This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 different components of the travel motor including the head, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the process.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 parts from the travel motor in 27 steps using various tools. The assembly process reverses the disassembly steps and involves installing the parts back onto the travel motor in the correct order and orientation using lubricants and following safety precautions for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. The disassembly process involves removing 27 parts from the travel motor in 27 steps using various tools. The assembly process reverses the disassembly steps and involves installing the parts back onto the travel motor in the correct order and orientation using lubricants and following safety precautions for parts under spring force.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fijsekkdmdm2w
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8uesjdkdmdm
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. The assembly process lists 28 steps for reinstalling these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly processes.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjkkekmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing and ensuring proper alignment of parts such as the cam plate with keys. Special tools are required for tasks like removing races and installing seals. Safety precautions are provided to watch for spring forces.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f8sejdkdmdijd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkskmmdmd1
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section then lists the 28 steps to reinstall each part in reverse order, noting the proper lubrication and torque specifications. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
More Related Content
Similar to Caterpillar Cat 336E Excavator (Prefix T3Z) Service Repair Manual (T3Z00001 and up).pdf
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct reassembly. Special safety precautions and tools are listed for components under spring force.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjfyjsekdmme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...hfhjskedme
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, pistons, and housing cover. The assembly process lists 28 steps to reinstall these components in the reverse order, noting the importance of lubrication, torque specifications, and proper alignment of parts. Tools including an adapter, bolts, eyebolt, retaining ring pliers, and bearing puller are required for the disassembly and assembly work.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...yqen95561858
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...ze3xiandiao
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section similarly outlines 28 steps to reinstall each part in reverse order, noting the importance of lubrication and proper alignment of components. Tools required are listed for specific removal and installation tasks.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...f7usuejkdkddm3
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and noting alignment marks to ensure correct positioning. Special safety precautions and tools are listed for components under spring force.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...ufs89eodkdmdm
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkskmmdmd1
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E L Excavator (Prefix TEG) Service Repair Manual (TEG00001...jdkksmemmd
This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar Cat 336E and 336E L Excavator (Prefix TEG) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. Similarly, the assembly section lists 28 steps to reinstall each part in reverse order, noting proper lubrication and torque specifications. Tools required are also outlined.
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing 27 different components of the travel motor including the head, springs, plates, seals, and housing cover. Detailed steps are provided for each part along with accompanying illustrations. The assembly section then lists the 28 steps to reinstall each part in reverse order, noting the proper lubrication and torque specifications. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
Similar to Caterpillar Cat 336E Excavator (Prefix T3Z) Service Repair Manual (T3Z00001 and up).pdf (20)
Caterpillar Cat W345B Series II Material Handler (Prefix CDY) Service Repair ...paws21610697
This document provides assembly instructions for a swing drive on a W345B Series II wheeled excavator. It includes a list of required tools and 40 steps to assemble the various components of the swing drive, such as bearings, seals, gears, and housings. Special attention is given to cleaning parts, applying lubricants, and torquing bolts to the specified values. The instructions also cover installing the assembled swing drive into the excavator's main frame.
1. Remove the fuel injection pump housing and governor from the engine as a single unit using lifting sling and hoist. Disconnect all connecting lines and tubes.
2. Disassemble the fuel injection pump housing by removing the retaining ring, filter base, tubes and other attached components.
3. Inspect all seals and gaskets, replacing any that are damaged, to prepare the housing for assembly.
This document provides installation instructions for removing and installing an axle shaft on the steering axle of an M325D Material Handler excavator. It is a 15 step process that includes draining fluids, removing bolts and pins, lifting out heavy components using lifting devices, replacing seals and bushings, and reinstalling components in reverse order. Special tools are required and Loctite threadlocker is used on reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides installation instructions for separating an upper frame from an undercarriage frame on an excavator. It outlines 33 steps including removing components like the stick, front and rear drive shafts, swivel, and left boom cylinder. It instructs using tools and lifting devices to reposition pins and plates to separate the frames while supporting heavy components weighing up to 500 pounds. Proper identification of hose and tube assemblies is noted for reinstallation.
Caterpillar Cat M325D L MH EXCAVATOR (Prefix KAY) Service Repair Manual (KAY0...paws21610697
This document provides instructions for disassembling and assembling the swing drive of an M325D L Material Handler excavator. It lists the required tools and presents a 31 step disassembly procedure and a 29 step assembly procedure. The procedures involve removing and installing various components of the swing drive like gears, shafts, bearings, seals and housings. Precautions are provided regarding cleanliness and safety.
The document provides instructions for disassembling the front and rear final drive carriers, hubs, and brakes of an M320 excavator. The 28 step procedure describes how to remove components like planetary carriers, sun gears, ring gears, brake pistons, bearings, and seals. Tools required include retaining ring pliers, pullers, wrenches, and hammers. Safety notices are provided to release hydraulic pressure and contain fluids before disassembly.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, and hub. The assembly procedure provides steps to install 23 components in reverse order and includes checking brake clearance and installing seals and bearings. Tools required include retaining ring pliers, drivers, spanners, pry bars, pullers, and torque wrenches.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
The document provides instructions for disassembling and assembling the main hydraulic pump of a M317D2 Wheeled Excavator. It lists 34 steps for disassembly, removing components like pistons, springs, seals and bearings. It then lists 36 steps for assembly, replacing components and using various tools to set dimensions and install retaining rings, seals and bearings. Precision is required to mark positions of parts and reinstall components in their original orientation for proper function.
This document provides instructions for disassembling and assembling a swing drive on a wheeled excavator model M316D. The removal procedure involves releasing hydraulic pressure, removing hoses and bolts, and using lifting tools to remove the swing drive assembly. The disassembly procedure then describes using various tools to remove retaining rings, plates, discs, seals, gears, and other internal components. The assembly procedure outlines cleaning and lubricating parts, and using tools to reinstall components in reverse order, taking care to properly seat bearings and tighten nuts to the specified torques.
The document provides instructions for disassembling the front and rear axles of an M315F wheeled excavator. It lists required tools and presents a 23 step procedure for removing components like carrier housings, planetary gears, bearings, seals, and hubs. Detailed illustrations accompany each step to show how to properly disassemble parts. Safety notices are included to handle fluids and springs safely during the process.
The document provides disassembly and assembly instructions for the travel motor of an M312 excavator. It lists 44 steps to disassemble the travel motor and its components. These include removing covers, gaskets, seals, valves, springs, pins, and other parts. It then lists the assembly steps in reverse order, noting to replace all seals and gaskets, apply oil, and ensure cleanliness during assembly.
Caterpillar Cat M312 Excavator (Prefix 6TL) Service Repair Manual (6TL00001-0...paws21610697
This document provides the disassembly and assembly procedures for the swing drive of an M312 excavator. The disassembly procedure involves 28 steps to remove components such as the swing brake assembly, discs, plates, piston, seals, shaft, gears, bearings, and housing. The assembly procedure involves 17 steps and requires various tools to install components in the reverse order of disassembly while applying lubricant and ensuring proper torque specifications are achieved.
This document provides instructions for removing and installing engine oil filter bases and related components on Caterpillar 3304B and 3306B engines. The procedures describe removing the oil filter, oil filter base, gaskets and O-rings. Instructions are provided for disassembling the oil filter base by removing covers, bolts, springs and plungers. Reassembly and installation steps are also outlined. Tools required are listed for each procedure. Precautions are noted to keep parts clean and contain fluids.
Caterpillar Cat D250E II Articulated Truck (Prefix 4PS) Service Repair Manual...paws21610697
The document provides instructions for disassembling and assembling the piston pump used for steering on a D250E II Articulated Truck. The disassembly procedure involves removing 21 individual parts from the pump housing. The assembly procedure instructs assembling the 21 parts in the reverse order, applying lubrication and torque specifications as needed. Tools required include various drivers, pliers, and lubricants.
The document provides instructions for disassembling and assembling the governor of an articulated truck. It lists 57 steps to disassemble the front and rear housings of the governor. Tools required include a governor repair fixture, retaining ring pliers, pin punch, clevis driver, and legs to mount the rear housing. Cautions are provided regarding cleaning parts and containing fluids during maintenance.
The document provides instructions for disassembling and assembling a Type I governor used in Caterpillar 3114, 3116, and 3126 engines. It describes 35 steps to disassemble the governor front housing and 19 additional steps to disassemble the rear housing. Various parts are inspected for wear or damage during disassembly. Cleaning and replacement parts are also discussed. Tools required are listed.
The document provides instructions for removing and installing various engine components on a Caterpillar 3408 industrial engine, including the oil cooler, oil filter base, oil bypass valves, engine oil cooler/lines, aftercooler, and turbocharger. The procedures describe removing bolts, hoses, seals, and other parts, cleaning components, applying sealant, and reinstalling parts in reverse order.
The document provides instructions for removing and installing wheel spindles on Caterpillar articulated dump trucks. It describes removing the wheels, bearings, and seals before removing the brake shoes. It then details removing pins and springs to separate the brake shoes from the spider. Reinstallation follows the reverse order. Instructions are also given for disassembling and assembling suspension cylinders.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
2. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 1 23:51:08 UTC+0800 2020
10/10
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Aug 1 23:52:04 UTC+0800 2020
5/5
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: MOBILE HYD POWER UNIT
Model: 336E MOBILE HYD POWER UNIT T3Z
Configuration: 336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E Mobile Hydraulic Power Unit T3Z00001-UP (MACHINE) POWERED BY C9.3...
2020/8/1
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...