This document provides the disassembly and assembly procedures for the travel motor of a 336E excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installing them and ensuring proper alignment of parts using marks made during disassembly. Special safety precautions and tools are noted throughout to properly release spring forces and install seals and bearings.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
Caterpillar cat 336 e l excavator (prefix cmr) service repair manual (cmr0000...fjskekmdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove all components of the travel motor. Key steps include using an air pressure tool to remove the brake piston, pressing out bearing races, and removing springs. The assembly procedure reverses the disassembly process in 27 steps and provides details on lubricating parts and ensuring proper alignment of components like pistons and keys. Tools required include an adapter, nuts, washers, eyebolts, retaining ring pliers, a bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 336 e l excavator (prefix jrj) service repair manual (jrj0000...fjskekmdm
The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. It lists 27 steps for disassembly, removing components like the head, springs, brake piston, plates and discs. It then lists 28 steps for assembly, reinstalling these components in reverse order and noting proper lubrication and torque specifications. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group and Loctite.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjskekmdm
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the piston assemblies, cam plate, and brake piston.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix bzy) service repair manual (bzy0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate and keys. Special tools are listed that are required for tasks like removing races and installing seals. Safety notices advise wearing protective equipment when working with spring-loaded parts.
Caterpillar cat 336 e l excavator (prefix cmr) service repair manual (cmr0000...fjskekmdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove all components of the travel motor. Key steps include using an air pressure tool to remove the brake piston, pressing out bearing races, and removing springs. The assembly procedure reverses the disassembly process in 27 steps and provides details on lubricating parts and ensuring proper alignment of components like pistons and keys. Tools required include an adapter, nuts, washers, eyebolts, retaining ring pliers, a bearing puller, and Loctite.
Caterpillar cat 336 e l excavator (prefix dpx) service repair manual (dpx0000...fjskekmdm
This document provides instructions for disassembling and assembling a 336E L excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, O-rings, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly process in 21 steps and provides warnings about spring-loaded components and ensuring proper alignment of parts. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group, and Loctite.
Caterpillar cat 336 e l excavator (prefix jrj) service repair manual (jrj0000...fjskekmdm
The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator. It lists 27 steps for disassembly, removing components like the head, springs, brake piston, plates and discs. It then lists 28 steps for assembly, reinstalling these components in reverse order and noting proper lubrication and torque specifications. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, driver group, bearing puller group and Loctite.
Caterpillar cat 336 e h excavator (prefix jea) service repair manual (jea0000...fjskekdmjekm
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are included to properly release spring forces and avoid damaging mating surfaces. Tools required include an eyebolt, retaining ring pliers, bearing puller, and adapter to securely hold parts during disassembly and assembly.
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
Caterpillar cat 336 e ln excavator (prefix yce) service repair manual (yce000...fjsekdmmeed
1. The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator.
2. The disassembly procedure involves removing 27 different parts from the travel motor in a specific order using various tools.
3. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and align markings to ensure proper assembly.
Caterpillar cat 336 e ln excavator (prefix yce) service repair manual (yce000...kmf9ioseodk
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating parts and ensuring proper alignment of components like the piston assemblies and cam plate. Tools required include an adapter, nuts, bolts, eyebolt, retaining ring pliers, bearing puller group, and loctite.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...kmf9ioseodk
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys. Special tools are required for tasks like removing races and installing seals. Proper torque values and cautions for spring-loaded parts are also noted.
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar Cat 336E L Excavator (Prefix TMZ) Service Repair Manual (TMZ00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...kmf9ioseodk
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar Cat 336E L and 336E LN Excavator (Prefix TMZ) Service Repair Manu...yan77xunhao
This document provides the disassembly and assembly procedures for the travel motor of a 336E LN excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installation and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the procedures.
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Caterpillar cat 336 e ln excavator (prefix tmz) service repair manual (tmz000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Massey ferguson mf 7242 combine parts catalogue manualhfhjskedme
This document provides a parts list for a Massey Ferguson MF 7242 combine. It includes 128 items with part numbers, quantities, descriptions, and comments. The parts listed are for the knives and fingers, table auger right hand, and table auger left hand components of the combine.
Massey ferguson mf 3455 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3445 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3435 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3425 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3355 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3350 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3340 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3330 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods of the MF 3315 and 3325 tractors. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3325 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods of the MF 3315 and 3325 tractors. The parts lists include the part numbers, quantities, descriptions, and any comments or replacement part numbers. The diagrams visually show the layout and components.
More Related Content
Similar to Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg00001 and up)
Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg0000...fjsekqazxkdmmem
The document provides disassembly and assembly instructions for a 336E and 336E L excavator travel motor. It lists required tools and parts and outlines 27 steps to disassemble the travel motor, removing components like the head, springs, brake piston, and seals. It then describes 21 steps for reassembling the travel motor, providing notes on lubrication and proper positioning of parts like the brake piston, cam plate, and head. The instructions are accompanied by illustrations of each step for clarification.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjekkdmmem
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27 assembly steps install components in reverse order, including keys, seals, bearings, piston assemblies and the rotating assembly. Precautions are provided for spring loaded components and proper positioning of parts is emphasized.
Caterpillar cat 336 e excavator (prefix teg) service repair manual (teg00001 ...fjjskekdm
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. It contains 27 steps for disassembly, removing components like the head, springs, brake piston, plates and seals. The 27-step assembly procedure instructs how to rebuild the travel motor by installing components in reverse order, like seals, piston actuator, cover and retaining rings. Precautions are provided regarding spring force and proper positioning of parts. Tools required are listed in a table.
Caterpillar cat 336 e ln excavator (prefix yce) service repair manual (yce000...fjsekdmmeed
1. The document provides instructions for disassembling and assembling the travel motor of a 336E L excavator.
2. The disassembly procedure involves removing 27 different parts from the travel motor in a specific order using various tools.
3. The assembly procedure instructs assembling the travel motor in the reverse order and notes to lubricate parts and align markings to ensure proper assembly.
Caterpillar cat 336 e ln excavator (prefix yce) service repair manual (yce000...kmf9ioseodk
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating parts and ensuring proper alignment of components like the piston assemblies and cam plate. Tools required include an adapter, nuts, bolts, eyebolt, retaining ring pliers, bearing puller group, and loctite.
Caterpillar cat 336 e l excavator (prefix yce) service repair manual (yce0000...kmf9ioseodk
This document provides the disassembly and assembly procedures for a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components and ensuring proper alignment of parts like the cam plate keys. Special tools are required for tasks like removing races and installing seals. Proper torque values and cautions for spring-loaded parts are also noted.
This document provides instructions for disassembling and assembling a 336E excavator travel motor. The disassembly procedure involves 27 steps to remove components like the motor head, springs, brake piston, rotating assembly, and seals. The assembly procedure describes 28 steps and requires various tools to reinstall the components in the reverse order of disassembly while ensuring proper alignment and torque specifications are followed. Precautions are provided to watch for spring forces and avoid damaging mating surfaces.
Caterpillar Cat 336E L Excavator (Prefix TMZ) Service Repair Manual (TMZ00001...f8usiejdkmdd
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Caterpillar cat 336 e l excavator (prefix tmz) service repair manual (tmz0000...kmf9ioseodk
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor housing including the head, springs, brake piston, plates, and seals. The assembly procedure instructs installing these 27 parts in reverse order and provides notes to ensure proper installation of parts like pistons, seals, and bearing races. Tools required include an adapter, nuts, washers, eyebolt, retaining ring pliers, bearing puller, and Loctite.
Caterpillar Cat 336E L and 336E LN Excavator (Prefix TMZ) Service Repair Manu...yan77xunhao
This document provides the disassembly and assembly procedures for the travel motor of a 336E LN excavator. The disassembly procedure involves 27 steps to remove components such as the head, springs, brake piston, plates, and seals. The assembly procedure reverses the disassembly steps and includes lubricating components before installation and ensuring proper alignment of parts. Tools such as an eyebolt, retaining ring pliers, and bearing puller are required to complete the procedures.
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Caterpillar cat 336 e ln excavator (prefix tmz) service repair manual (tmz000...fjsekdmmeed
This document provides instructions for disassembling and assembling a 336E LN excavator travel motor. The disassembly procedure involves removing 27 parts from the travel motor in a specific order. The assembly procedure instructs assembling the travel motor in the reverse order, noting proper lubrication and torque specifications for reinstallation. Tools required are also listed.
Similar to Caterpillar cat 336 e l excavator (prefix teg) service repair manual (teg00001 and up) (12)
Massey ferguson mf 7242 combine parts catalogue manualhfhjskedme
This document provides a parts list for a Massey Ferguson MF 7242 combine. It includes 128 items with part numbers, quantities, descriptions, and comments. The parts listed are for the knives and fingers, table auger right hand, and table auger left hand components of the combine.
Massey ferguson mf 3455 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3445 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3435 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3425 vsf tractors parts catalogue manualhfhjskedme
This document contains parts lists and diagrams for engine components of Massey Ferguson 3425, 3435, 3445, and 3455 tractors, including:
- The cylinder block, with lists of parts, part numbers, and quantities for each model.
- The crankshaft, pistons, and connecting rods, again with detailed parts lists and diagrams for each model.
- The cylinder head, with exploded diagrams and parts listings specific to each model.
- A page showing the heater/starter switch components for the MF 3425 model.
The document provides maintenance technicians with the information needed to service and repair engine parts for these Massey Ferguson tractor models. Parts are identified
Massey ferguson mf 3355 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3350 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3340 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3330 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods of the MF 3315 and 3325 tractors. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 3325 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods of the MF 3315 and 3325 tractors. The parts lists include the part numbers, quantities, descriptions, and any comments or replacement part numbers. The diagrams visually show the layout and components.
Massey ferguson mf 3315 vsf tractors parts catalogue manualhfhjskedme
This document provides parts information for Massey Ferguson tractors models MF 3315, 3325, 3330, 3340, 3350, and 3355. It includes detailed parts lists and diagrams for the engine, alternator, starter, cylinder block, crankshaft, pistons, and connecting rods. The parts lists include the part numbers, quantities, descriptions, and any relevant comments for each component.
Massey ferguson mf 1345 compact tractors parts catalogue manualhfhjskedme
This document provides parts lists and descriptions for components of Massey Ferguson MF 1325/1335/1345 compact tractors, including the cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It lists each part number, quantity, description, and any relevant comments or footnotes for each item. The parts lists are broken down by component and model to provide the specific parts for the MF 1325, MF 1335, and MF 1345 models.
Massey ferguson mf 1335 compact tractors parts catalogue manualhfhjskedme
This document provides parts lists and descriptions for components of Massey Ferguson MF 1325/1335/1345 compact tractors, including the cylinder block, crankshaft, pistons, connecting rods, and cylinder head. It lists each part number, quantity, description, and any relevant comments or footnotes for each item. The parts lists are broken down by component and model to provide the specific parts for the MF 1325, 1335, and 1345 models.
Massey ferguson mf 1325 compact tractors parts catalogue manualhfhjskedme
This document contains parts lists and specifications for cylinder blocks, crankshafts, pistons, connecting rods, and cylinder heads for Massey Ferguson MF 1325, 1335, and 1345 compact tractors. It includes detailed lists of each part required with corresponding part numbers and quantities. Specifications vary slightly between the three tractor models.
Massey ferguson mf 1260 compact tractor ( e60101 - hst non hst) parts catal...hfhjskedme
This document provides parts information for the Massey Ferguson MF 1260 compact tractor, including multiple assemblies and components. It lists 61 individual items that make up the timing gear housing assembly, providing part numbers, quantities, descriptions, and other relevant details for each part. Special notes are included to indicate part number changes associated with specific serial or engine numbers. The document also includes parts listings for other assemblies like the cylinder head, block, and turbocharger.
Komatsu pc1800 6 hydraulic excavator service repair manual (sn 11002 and up)hfhjskedme
This shop manual provides instructions for repairing and maintaining the Komatsu PC1800-6 excavator. It is divided into sections covering general information, structure and function, testing and adjusting, disassembly and assembly, and other topics. The manual notes that the PC1800-6 is equipped with a SAA6D140E-3 engine, and the engine shop manual should be referenced for engine-related repairs. Technicians are advised to follow safety precautions, prepare properly for each repair job, and consult the manual for the correct procedures and standards.
Komatsu pc1800 6 hydraulic excavator service repair manual (sn 10011 and up)hfhjskedme
This shop manual provides instructions for repairing and maintaining the Komatsu PC1800-6 excavator. It is divided into sections covering general information, structure and function, testing and adjusting, disassembly and assembly, and other topics. The manual notes that the PC1800-6 is equipped with a SAA6D140E-3 engine, and the engine shop manual should be referenced for engine-related repairs. Technicians are advised to follow safety precautions, prepare properly for each repair job, and consult the manual for the correct procedures and standards.
Komatsu pc1800 6 galeo hydraulic excavator operation & maintenance manual...hfhjskedme
1) This manual provides safety and operational instructions for Komatsu PC1800-6 Hydraulic Excavators with serial numbers 11035 and up.
2) The excavator is designed for digging and loading work. Safety labels and precautions in the manual must always be followed.
3) In addition to operational details, the manual covers maintenance schedules, troubleshooting, specifications, and attachments like loading shovels that can be used with the excavator. Users should contact their distributor for any revision updates.
Komatsu pc250 lc 6 excavator service repair manual sn a80001 and uphfhjskedme
This document is a shop manual for Komatsu excavators providing technical information for maintenance and repair work. It includes sections on general safety procedures, the structure and function of components, testing and adjustment procedures, disassembly and assembly instructions, and maintenance standards for parts. The manual is intended to help technicians safely and effectively service the excavators by providing accurate technical information.
Komatsu pc220 ll 6 excavator service repair manual sna85001 and uphfhjskedme
This document is a shop manual addendum for the Komatsu PC200LL-6 and PC220LL-6 logging excavators. It provides information for servicing and repairing these excavator models, with sections covering general information, structure and function, testing and troubleshooting, disassembly and assembly, and maintenance standards. Komatsu policies on improving products and revising publications are also mentioned. The manual instructs technicians to use information from standard shop manuals for any topics not covered specifically for the PC200LL and PC220LL models.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR TEG
Configuration: 336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03863290
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 by 250 mm (10 inch) Threaded Rod 1
B
8T-0651 Bolt 1
8T-4167 Hard Washer 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
Start By:
a. Remove the travel motor.
1. Fasten the travel motor in Tooling (A) in a vertical position. The weight of the travel motor
is approximately 60 kg (132 lb).
1/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00887295
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
Note: During the removal of head (2) from the travel motor, be careful not to damage the
mating surfaces of the components.
3. Remove bolts (1).
4. Remove head (2) from the body of the travel motor.
2/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00887302
5. Remove O-ring seal (3), port plate (4), and bearing (5).
Illustration 3 g00887311
6. Remove O-ring seals (6). Remove springs (7).
Illustration 4 g00887331
Illustration 5 g00890074
This is an example of the use of Tooling (B).
3/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 7. Place a shop towel over brake piston (8). Retain brake piston (8) with Tooling (B). Apply
approximately 525 kPa (75 psi) of shop air pressure to brake release Port (Y). Make sure
that the shop air pressure is free of water. Brake piston (8) will move up the piston guide,
and out of the piston guide. Remove brake piston (8) from the body of the travel motor.
Illustration 6 g00887336
8. Remove seal (9) and backup ring (10) from the brake piston.
9. Remove seal (11) and backup ring (12) from the brake piston.
Illustration 7 g00887355
10. Remove plates (13) and friction discs (14).
4/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g02107957
Illustration 9 g00887405
Illustration 10 g00887424
11. Install Tooling (C) into shaft (15). Use a prybar to remove the rotating assembly (16) from
the housing.
12. Remove Tooling (C) from shaft (15).
13. Remove shaft (15) from rotating assembly (16).
Illustration 11 g00887426
5/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Use Tooling (D) in order to remove retaining ring (17) from shaft (15).
Illustration 12 g00887445
15. Use a suitable press in order to remove bearing race (18) from shaft (15).
Illustration 13 g00887463
16. Rotate shaft (15). Use a suitable press and tooling (E) in order to remove bearing race (19)
from shaft (15).
Illustration 14 g00887501
17. Remove cam plate (20) from barrel assembly (21).
6/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00887520
18. Remove piston assemblies and retainer plate (22) from barrel assembly (21).
Note: Place marks on the pistons and the barrel assembly. The pistons must be returned to
the original position.
Illustration 16 g00887558
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
19. Remove ball (23) and springs (24).
7/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 17 g02107975
20. Remove bearing (25).
21. Remove keys (26) and locating pins (not shown) from the body of the travel motor.
Illustration 18 g00887589
22. Rotate the housing. Use Tooling (F) in order to remove retaining ring (27).
23. Remove lip seal (28).
Illustration 19 g00887619
24. Remove bolts (29) and cover (30).
8/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887729
25. Remove seal (31) and backup ring (32).
Illustration 21 g00887754
26. Remove piston actuator (33) and seal (34).
Illustration 22 g00887762
27. Remove O-ring seal (35) from the housing of the travel motor.
9/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR TEG
Configuration: 336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07175112
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) to install lip seal
(28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 14 g02107957
18. Use Tooling (C) to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g02107975
19. The notches in cam plate (20) must align with keys (26). The keys are located in the bottom
of the housing of the travel motor.
Illustration 17 g00887355
7/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing so that the cast mark on brake piston (8) is aligned
with the brake supply passage in the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level to
prevent damage to the O-ring seals.
8/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 240 ± 40 N·m (177 ± 30 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 20:32:00 UTC+0800 2020
10/10
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Eng...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR TEG
Configuration: 336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i07191698
Final Drive and Travel Motor - Remove and Install
SMCS - 4050; 4351
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
1. Refer to Operation and Maintenance Manual, "Final Drive Oil - Change" for the correct
draining and filling procedures.
1/5
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 1 g02108761
2. Remove bolts (1) and cover (2).
3. Separate the track.
Illustration 2 g02108762
4. Disconnect hose assemblies (3) ( 4), and (6). Remove fitting (5).
2/5
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 3 g02108781
5. Attach Tooling (A) and a suitable lifting device to final drive and travel motor (7). The
weight of final drive and travel motor (7) is approximately 860 kg (1896 lb). Put a slight
lifting tension on final drive and travel motor (7).
Illustration 4 g02108790
Note: Mark the orientation of the final drive and travel motor assembly for installation
purposes.
6. Remove bolts (8).
Illustration 5 g02108791
7. Use two bolts (8) to remove final drive and travel motor (7).
8. Carefully remove final drive and travel motor (7).
9. Remove bolts (8) from the frame.
3/5
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 6 g02108793
10. Remove bolts (9), counterbalance valve (10), and the O-ring seals.
Illustration 7 g02108794
11. Attach Tooling (B) and a suitable lifting device to travel motor (11). The weight of travel
motor (11) is approximately 84 kg (185 lb).
12. Remove four bolts (12) and travel motor (11) from final drive (13).
4/5
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 8 g02108914
13. Remove coupling (14).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 1U-9200 Lever Puller Hoist 1
B 439-3938 Link Bracket 1
C - Loctite C5A Copper Anti-Seize -
1. Before assembly remove all compounds, oil, and dust.
2. Install final drive and travel motor (7) in the reverse order of removal.
a. Tighten bolts (9) to a torque of 80 ± 8 N·m (60 ± 6 lb ft).
b. Apply Tooling (C) to the threads of bolt (8).
c. Tighten bolts (8) to a torque of 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional
angle of 45 ± 5 degrees. Refer to Service Magazine, M0083843, "An Improved Bolt
Tightening Procedure for the Critical Joints Is Now Used on All Excavators" for more
detail information.
d. Tighten hose assembly (3) to a torque of 160 ± 16 N·m (120 ± 12 lb ft).
e. Tighten bolts (1) to a torque of 130 ± 10 N·m (95 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jul 20 20:32:56 UTC+0800 2020
5/5
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 336E L EXCAVATOR TEG
Configuration: 336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine
Disassembly and Assembly
336E Excavator and 336E MHPU Mobile Hydraulic Power Unit Machine Systems
Media Number -KENR8157-05 Publication Date -01/06/2014 Date Updated -12/06/2014
i03885522
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Brackets 3
B 154-6183 Forcing Bolts 3
C 138-7576 Link Brackets 3
Start By:
a. Remove the final drive and the travel motor.
Illustration 1 g02131413
1/8
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. 1. Attach Tooling (A) and a suitable lifting device to cover (2). The weight of cover (2) is
approximately 20 kg (45 lb). Remove bolts (1) and cover (2).
Illustration 2 g02131414
2. Remove plate (3) from cover (2).
Illustration 3 g02131415
3. Remove sun gear (4), spacer (5), and planetary gear assembly (6).
2/8
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 4 g02131875
4. Remove retaining ring (7), washer (8), planetary gear (9), roller bearing (11), and washer
(12) from carrier assembly (13).
5. Remove retaining ring (10) and sun gear (14) from carrier assembly (13).
Illustration 5 g02131876
6. Remove spacer (16).
7. Attach Tooling (A) and a suitable lifting device to planetary gear assembly (15). The weight
of planetary gear assembly (15) is approximately 32 kg (70 lb). Remove planetary gear
assembly (15).
3/8
336E & 336E L Excavators TEG00001-UP (MACHINE) POWERED BY C9.3 Engine...
2020/7/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...