This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual Instant ...shibi1322
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...diskdkkdmmd
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual Instant ...yin9niaojiao
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...cdfzxs
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...fjjsekkksmeik
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
The document aims to safely depressurize hydraulic systems to allow disconnection of components or lines for maintenance.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...jfdjskmdmme
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual Instant ...shibi1322
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...diskdkkdmmd
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual Instant ...yin9niaojiao
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...cdfzxs
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...fjjsekkksmeik
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
The document aims to safely depressurize hydraulic systems to allow disconnection of components or lines for maintenance.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...jfdjskmdmme
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...cdsaas
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
The document aims to safely depressurize hydraulic systems to allow disconnection of components or lines for maintenance.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar cat 336 d l excavator (prefix j2f) service repair manual (j2f0000...ikdkdmdm
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, covering tasks like positioning the travel motor and final drive, installing seals and bolts, and refilling fluids. Tools and safety precautions are also noted.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, covering tasks like positioning the travel motor and final drive, installing seals and bolts, and reconnecting hoses. Tools and safety precautions are also noted.
Caterpillar Cat 336F L Excavator (Prefix KCS) Service Repair Manual (KCS00001...cnp692569
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing fasteners and connectors, loosening clamps, and installing replacement parts in the reverse order of removal while applying sealants and lubricants and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
1. The document provides step-by-step instructions for disassembling the travel motor of a 336F excavator.
2. It describes removing 27 components and parts from the travel motor in a specific sequence using various tools.
3. Special care must be taken when removing springs and components under pressure to avoid injury from released forces.
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. The disassembly process involves 30 steps to remove all components of the travel motor. The assembly process reverses the disassembly with 27 steps and requires various tools to reinstall components in the proper order and orientation. Precautions are outlined to prevent injury from spring forces.
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing parts in the specified order, cleaning components, installing new gaskets and O-rings, and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
This document provides instructions for disassembling the travel motor on 336F and 336F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release stored energy from springs. Detailed illustrations accompany each step to ensure correct disassembly. Required tools are listed.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...cnp692569
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread lock to bolts and torquing to specification.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual (YEP00001...cnp692569
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing seals, bearings, springs and other components from the motor housing. The assembly process details installing these components in reverse order and applying lubricant or threadlock where specified. Proper torque values are listed for fasteners. The instructions note to mark components' orientations before removal to aid reinstallation.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001...cnp692569
The document provides instructions for disassembling and assembling a travel motor. It details 28 steps for travel motor assembly, including installing seals, springs, pistons and other components. Removal of the final drive and travel motor requires draining fluids, removing bolts and hoses, and lifting out the assembly. Reinstallation requires cleaning, applying sealant to bolts, and torquing bolts to the specified values.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
More Related Content
Similar to Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M00001 and up).pdf
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...cdsaas
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
The document aims to safely depressurize hydraulic systems to allow disconnection of components or lines for maintenance.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fijsekkdmdm2w
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...zan2736ban
The document provides instructions to remove and install the final drive and travel motor assembly on a 336D L excavator. The removal procedure involves 13 steps including disconnecting hoses, removing bolts, and lifting the assembly off with the aid of tools. The installation procedure reverses these steps, taking care to properly position the components and tighten bolts to the specified torques. Proper containment of fluids and cleaning of parts is emphasized throughout.
Caterpillar cat 336 d l excavator (prefix j2f) service repair manual (j2f0000...ikdkdmdm
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, covering tasks like positioning the travel motor and final drive, installing seals and bolts, and refilling fluids. Tools and safety precautions are also noted.
Caterpillar Cat 336D L Excavator (Prefix J2F) Service Repair Manual Instant D...fujkskemdmdm4r
The document provides instructions for removing and installing a final drive and travel motor on a 336D L excavator. It describes 13 steps to remove the component, which include disconnecting hoses, removing bolts and brackets, and lifting the final drive and travel motor assembly out. 11 steps are listed to install the component, covering tasks like positioning the travel motor and final drive, installing seals and bolts, and reconnecting hoses. Tools and safety precautions are also noted.
Similar to Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M00001 and up).pdf (10)
Caterpillar Cat 336F L Excavator (Prefix KCS) Service Repair Manual (KCS00001...cnp692569
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing fasteners and connectors, loosening clamps, and installing replacement parts in the reverse order of removal while applying sealants and lubricants and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
1. The document provides step-by-step instructions for disassembling the travel motor of a 336F excavator.
2. It describes removing 27 components and parts from the travel motor in a specific sequence using various tools.
3. Special care must be taken when removing springs and components under pressure to avoid injury from released forces.
This document provides instructions for disassembling and assembling the travel motor of a 336F excavator. The disassembly process involves 30 steps to remove all components of the travel motor. The assembly process reverses the disassembly with 27 steps and requires various tools to reinstall components in the proper order and orientation. Precautions are outlined to prevent injury from spring forces.
The document provides instructions for removing and installing various components of a Caterpillar C9.3 engine, including the combustion head, ARD nozzle heater relay, ARD fuel solenoid valve, exhaust manifold, and exhaust elbow. The procedures include removing parts in the specified order, cleaning components, installing new gaskets and O-rings, and torquing fasteners to the specified values. Safety precautions are provided regarding working on hot engine components and with flammable liquids.
This document provides instructions for disassembling the travel motor on 336F and 336F L Excavator models. It outlines 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, barrel assembly, springs, seals, and other internal parts. Precautions are provided to safely release stored energy from springs. Detailed illustrations accompany each step to ensure correct disassembly. Required tools are listed.
Caterpillar Cat 336E L HVG Excavator (Prefix RBS) Service Repair Manual (RBS0...cnp692569
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread lock to bolts and torquing to specification.
Caterpillar Cat 336E L Excavator (Prefix YEP) Service Repair Manual (YEP00001...cnp692569
This document provides instructions for disassembling and assembling a travel motor. The disassembly process involves removing seals, bearings, springs and other components from the motor housing. The assembly process details installing these components in reverse order and applying lubricant or threadlock where specified. Proper torque values are listed for fasteners. The instructions note to mark components' orientations before removal to aid reinstallation.
Caterpillar Cat 336E L Excavator (Prefix KED) Service Repair Manual (KED00001...cnp692569
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly. 10 steps are outlined for removal, including draining oil, removing hoses and fittings, and using lifting tools. 13 steps are given for installation, with torque specifications for the reinstallation bolts.
3. Disassembly instructions for the final drive include removing the cover, plate, and links using lifting brackets and forcing bolts.
Caterpillar Cat 336E L Excavator (Prefix GTJ) Service Repair Manual (GTJ00001...cnp692569
The document provides instructions for disassembling and assembling a travel motor. It details 28 steps for travel motor assembly, including installing seals, springs, pistons and other components. Removal of the final drive and travel motor requires draining fluids, removing bolts and hoses, and lifting out the assembly. Reinstallation requires cleaning, applying sealant to bolts, and torquing bolts to the specified values.
The document provides instructions for installing and removing components related to the rear power take-off (RPTO) system on a Caterpillar C9.3 engine. The removal procedure includes removing the crankshaft rear seal, various bolts and gears, thrust washers, dowels, bearings, seals and the PTO shaft. The installation procedure specifies cleaning and lubricating parts before reinstalling components in reverse order, applying thread locking compound to bolts, and torquing bolts to the specified values.
This document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps for disassembly, removing components like the head, springs, plates, seals and bearings. It then outlines 17 steps for assembly, replacing these components in reverse order and noting specifics like lubrication, torque settings and alignment marks. Tools required are listed.
1. The document provides assembly instructions for a travel motor on an excavator. It details 28 steps to assemble the travel motor, including installing seals, springs, pistons, and other components.
2. Removal and installation instructions are provided for the final drive and travel motor assembly of an excavator. The procedure includes disconnecting hoses, removing mounting bolts, and lifting out the assembly.
3. Disassembly instructions are given for a final drive, including removing the cover, plate, and installing lifting brackets to remove internal components. Detailed diagrams accompany each step.
The document provides instructions for disassembling and assembling a travel motor. It details 28 steps for disassembling the travel motor, removing components like seals, springs, and plates. It then lists 13 steps for reassembling the travel motor and tightening components like bolts, hoses, and covers to the specified torques.
Caterpillar Cat 336D2 L Excavator (Prefix ZCT) Service Repair Manual (ZCT0000...cnp692569
This document provides disassembly and assembly instructions for the main hydraulic pump on a 336D2 L excavator. It lists over 50 steps to fully disassemble the pump by removing covers, valves, springs, seals, gears, and other components. The corresponding assembly section lists the steps to reinstall all components in reverse order, noting requirements for special tools and heating/pressing some bearings and seals back into place. Precautions are included for releasing spring forces to avoid injury.
Caterpillar Cat 336D2 L Excavator (Prefix YCF) Service Repair Manual (YCF0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for Caterpillar 336D2 and 336D2 L excavators. The disassembly procedure involves removing 30 parts in 8 steps, taking precautions for spring-loaded parts. The assembly procedure reinstalls the parts in 30 steps, heating and cooling certain parts, using tools to install retaining rings and measure end play, and filling the hydraulic system.
Caterpillar Cat 336D2 L Excavator (Prefix XBH) Service Repair Manual (XBH0000...cnp692569
This document provides instructions for installing and removing the final drive and travel motor, and disassembling and assembling the swivel, on Caterpillar 336D2 and 336D2 L excavators. The procedures include using various tools to lift heavy components, installing and tightening bolts, replacing O-rings and seals, and checking for leaks during assembly. Cleanliness is emphasized to prevent contamination.
Caterpillar Cat 336D2 L Excavator (Prefix WDC) Service Repair Manual (WDC0000...cnp692569
The document provides instructions for assembling and disassembling components of a piston motor (hydraulic fan) and hydraulic lockout control on excavator models 336D2 and 336D2 L. It describes 17 steps for assembling the piston motor, including installing bearings, seals, springs, and retaining rings. It also describes removing and disassembling the hydraulic lockout control into individual parts and reassembling it. Safety precautions are provided for parts under spring tension.
Caterpillar Cat 336D2 L Excavator (Prefix WBC) Service Repair Manual (WBC0000...cnp692569
The document provides instructions for removing and installing valve guides, valve seat inserts, an engine oil filter base, and oil cooler on a Caterpillar C9 engine. The removal procedures describe using various tools to remove the components from the cylinder head and engine. The installation sections explain cleaning and lubricating parts before reinstalling them using specific tools and following the correct procedure.
Caterpillar Cat 336D2 L Excavator (Prefix TLY) Service Repair Manual (TLY0000...cnp692569
The document provides instructions for disassembling and assembling a piston pump. It includes 30 steps for assembly, beginning with cleaning parts and ending by filling the hydraulic system with oil. The 3 steps for disassembly are: 1) removing bolts and the head, 2) removing internal components like pistons and bearings, and 3) using tools to remove the rotating group and bearing cone. Protective equipment is recommended as parts are under spring pressure.
Caterpillar Cat 336D2 L Excavator (Prefix LAM) Service Repair Manual (LAM0000...cnp692569
This document provides instructions for removing and installing the unit injector hydraulic pump on a Caterpillar C9 engine. The removal process involves disconnecting fuel lines and electrical connections, removing mounting bolts, and taking out the O-ring seal. Installation is the reverse of removal, and includes cleaning parts, applying a new O-ring seal, reinstalling mounting bolts, and reconnecting fuel lines and electrical connections. Proper cleaning and containment of fluids is emphasized. Both non-dual and dual tapered roller bearing pump types are covered.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050091
Air Compressor Drive Gear - Remove
SMCS - 1803-011-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
Start By:
A. Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install Tooling (A) on the air compressor drive gear.
3. Remove nut (2) and washer (3) .
4. Remove air compressor drive gear (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:33:15 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050094
Air Compressor Drive Gear - Install
SMCS - 1803-012-GE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install air compressor drive gear (4) on the air compressor crankshaft.
3. Install washer (3) and nut (2) .
4. Install Tooling (A) on the air compressor drive gear.
5. Tighten nut (2) to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
6. Place a driver which is slightly larger than the nut over the nut and tap the driver with a
hammer.
7. Tighten the nut again to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
End By: Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:34:10 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01897971
Hydraulic System Pressure - Release - Forest Machines
SMCS - 3000-553; 4250-553; 4300-553; 5050-553
S/N - B1K1-UP
S/N - B2L1-UP
S/N - B3M1-UP
S/N - B4N1-UP
Pressure Release Procedure
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the following hydraulic circuits before any hydraulic
lines are disconnected or removed from that hydraulic circuit.
• Boom hydraulic circuit
• Stick hydraulic circuit
• Heel hydraulic circuit
• Grapple hydraulic circuit
• Swing hydraulic circuit
• Travel hydraulic circuit
• Attachment hydraulic circuits (if equipped)
• Pilot hydraulic circuit
• Return hydraulic circuit
1/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Note: Refer to the Disassembly and Assembly Manual for additional information concerning
service of the components of specific hydraulic circuits.
Release Of Hydraulic Pressure From A Single Hydraulic
Circuit
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from a single hydraulic
circuit of the main hydraulic system.
1. Position the machine on level ground.
2/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 1 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that single hydraulic
circuit. This will also release any pressure that might be present in the pilot hydraulic
circuit.
Note: If the desired hydraulic circuit that requires service requires the activation of a switch
for operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Turn the engine start switch to the OFF position.
9. Slowly loosen the filler plug on the hydraulic tank and release the pressure from the
hydraulic tank. Leave the filler plug loose for a minimum of 45 seconds. This will release
the pressure that may be present in the return hydraulic circuit.
10. Tighten the filler plug on the hydraulic tank to the specified torque.
11. The pressure in the single hydraulic circuit that requires service is now released and lines
and components can be disconnected or removed from that hydraulic circuit.
Release Of Hydraulic Pressure From Multiple Hydraulic
Circuits
3/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from multiple hydraulic
circuits of the main hydraulic system.
1. Position the machine on level ground.
4/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 2 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that hydraulic circuit.
This will also release any pressure that might be present in the pilot hydraulic circuit.
Note: If the hydraulic circuit that requires service requires the activation of a switch for
operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Start the engine.
9. Place the hydraulic activation control lever in the UNLOCKED position. Do not move any
joysticks or pedals from the NEUTRAL position during this step. Do not activate any
switches during this Step.
10. Return the hydraulic activation control lever to the LOCKED position.
11. Shut off the engine.
12. Repeat Steps 4 through 11 for each additional hydraulic circuit that requires service.
13. After releasing the hydraulic pressure in each of the desired hydraulic circuits, place the
hydraulic activation control lever in the LOCKED position.
5/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. 14. Turn the engine start switch to the OFF position.
15. Slowly loosen the filler plug on the hydraulic tank and release the pressure. Leave the filler
plug loose for a minimum of 45 seconds. This will release the pressure that may be present
in the return hydraulic circuit.
16. Tighten the filler plug on the hydraulic tank to the specified torque.
17. The pressure in the multiple hydraulic circuits that require service is now released and lines
and components can be disconnected or removed from those hydraulic circuits.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:35:33 UTC+0800 2020
6/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01694093
Battery - Remove and Install
SMCS - 1401-010
Removal Procedure
Note: This machine contains four batteries. The batteries are connected in series. Mark the
position of both the batteries and the battery cables prior to removal.
1. Open the rear access door on the left side of the machine.
Illustration 1 g00872239
2. Move the battery disconnect switch (1) to the OFF position.
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Illustration 2 g00872229
3. Remove nuts (2) from battery covers (3) .
4. Remove battery covers (3) .
Illustration 3 g00872255
5. Move rubber covers (4) from the battery terminal posts.
6. Remove the negative terminals from each of the batteries.
7. Remove the positive terminals from each of the batteries.
8. Remove the batteries.
Installation Procedure
Note: This machine contains four batteries. The batteries are connected in series. Each battery
MUST be in the correct position in order for correct machine operation.
1. Install the batteries in the correct position.
2. Install the positive terminals on each of the batteries.
3. Install the negative terminals on each of the batteries.
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Illustration 6 g00872239
7. Move the battery disconnect switch (1) to the ON position.
8. Close the access door.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:36:28 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692348
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7113 Reverse Ratchet 1
1. Open the hood.
2. Disconnect the positive battery terminal. This will prevent any damage to the wiring or to
the alternator.
Illustration 1 g00871311
3. Disconnect wiring terminals (1), (2), and (3) from the alternator.
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 2 g00871323
4. Insert Tooling (A) in slot (4). Apply downward pressure in order to remove the belt.
Illustration 3 g00871363
5. Remove bolt (5) from the belt guard.
2/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 4 g00871375
6. Remove nut (6) and remove the bolt. Remove the guard.
Illustration 5 g00871388
7. Remove spacer (7) and bolt (8) .
8. Remove alternator (9) .
Installation Procedure
1. Place alternator (9) in position.
Illustration 6 g00871388
2. Install spacer (7) and bolt (8). Remove the alternator.
3/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 7 g00871375
3. Position the guard and install nut (6) .
Illustration 8 g00871363
4. Install bolt (5) in the belt guard.
Illustration 9 g00871323
5. Insert Tooling (A) in slot (4). Apply downward pressure in order to install the belt.
4/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Illustration 10 g00871311
6. Connect wiring terminals (1), (2), and (3) to the alternator.
7. Connect the positive battery terminal.
8. Close the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:37:24 UTC+0800 2020
5/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692671
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
1. Disconnect the battery cables.
Illustration 1 g00871495
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Illustration 2 g00871498
2. Place an index mark on all of the electrical wires that are connected to the electric starting
motor. Disconnect the electrical wires from the electric starting motor.
Illustration 3 g00871501
3. Remove top starter bolt (1) .
Illustration 4 g00871506
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. 4. Remove bottom starter bolts (2) and use a hoist and a lifting sling to remove starter (3). The
weight of the starter is approximately 32 kg (70 lb).
Installation Procedure
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket on the electric starting motor.
Illustration 5 g00871506
3. Use a hoist and a lifting sling to position starter (3) and install bottom starter bolts (2). The
weight of the starter is approximately 32 kg (70 lb).
Illustration 6 g00871501
4. Install top starter bolt (1) .
3/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Illustration 7 g00871495
Illustration 8 g00871498
5. Connect all of the electrical wires to the electric starting motor by using the index marks.
6. Connect the battery cables.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:38:20 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692852
Fuel Filter (Primary) and Fuel Filter Base - Remove and
Install
SMCS - 1261-010; 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench As 1
B
6V-9508 Face Seal Plug (11/16 inch by 16 THD) 2
6V-9829 Cap Assembly (11/16 inch by16 THD) 2
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...