This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with controls in neutral to release system pressure when servicing multiple circuits.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...yin9niaojiao
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components. Temperatures must be controlled for some parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...yin9niaojiao
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy components and ensuring proper hose, harness and bracket connections.
Caterpillar Cat 336D and 336D L Excavator (Prefix WRK) Service Repair Manual ...yin9niaojiao
The document provides instructions for removing and installing a final drive and travel motor on a Caterpillar 336D excavator. It lists required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...yin9niaojiao
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the rear gear group and related components on a 330D L excavator with a C9 engine. The removal process involves using tools to remove bolts, gears, bushings, bearings, and covers. The installation process gives specifics on cleaning parts, applying adhesives, inserting bearings at the proper angles and depths, and torquing bolts. Tolerances are provided for correct installation of several components.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual Instant D...yin9niaojiao
The document provides installation instructions for a swivel on an excavator. It describes removing the swivel by disconnecting hoses, removing bolts and lifting it out. It then details assembling the swivel by cleaning parts, installing seals and O-rings, positioning the housing over the rotor, and securing them with bolts. Finally, it describes installing the assembled swivel by connecting hoses and fittings and securing it with bolts.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...yin9niaojiao
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
The document provides instructions for disassembling the final drive of a 330D MH EXCAVATOR. It lists 31 steps to completely disassemble the final drive assembly including removing gears, carriers, shafts, seals and housings. Various tools are required including retaining ring pliers, link brackets, eyebolts and forcing bolts to separate the components. Cleanliness is important to prevent dirt from entering during disassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix ZBJ) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling a travel motor and final drive for Caterpillar 336F L and 336F LN excavators. It lists required tools and parts and includes diagrams illustrating the 27 steps to assemble the travel motor. These include installing seals, springs, plates, and fasteners in the proper sequence and orientation. The instructions also describe removing the final drive and travel motor as a unit and then separating the individual components.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix WTZ) Service Repair Manu...yin9niaojiao
This document provides the disassembly and assembly procedures for a 336F excavator travel motor. The disassembly procedure involves 30 steps to remove all components of the travel motor. The assembly procedure reverses the disassembly process in 27 steps and provides notes on proper installation of springs, seals, and ensuring alignment of keys and notches. Tools required include a transmission repair stand, lifting eyes, bolts, drivers and pullers. Personal protective equipment is recommended when working with springs.
Caterpillar Cat 336F L and 336F LN Excavator (Prefix KFT) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling a 336F excavator travel motor. It describes 27 steps to remove components such as the motor head, springs, seals, relief valves, plugs and ball bearings. Tools include a transmission repair stand, lifting eye assembly, driver group and retaining ring pliers. Safety precautions are provided to release spring forces and contain fluids during disassembly.
Caterpillar Cat 336E LH and 336E LNH Excavator (Prefix GNY) Service Repair Ma...yin9niaojiao
The document provides instructions for removing and installing a travel motor on an excavator. It is a 28-step procedure that includes draining oil, removing hoses and fittings, using lifting devices to remove the final drive and travel motor assembly, and reinstalling the components in reverse order. Precautions are provided for working with pressurized hydraulic systems and heavy components. The installation steps specify applying anti-seize compound to bolts and torquing them to the specified values.
Caterpillar Cat 336E H and 336E LH EXCAVATOR (Prefix JEA) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling the travel motor of a 336E excavator. It outlines 27 steps to disassemble the motor, removing components like the head, springs, brake piston, and bearing races. It then lists 28 steps for reassembling the motor, describing how to install seals, plates, springs and other parts in the reverse order of disassembly. Precautions are provided to prevent injury from spring forces and ensure proper alignment of parts.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FAJ) Service Re...yin9niaojiao
This document provides disassembly instructions for a travel motor on a 336D2 excavator. It lists 27 steps to fully disassemble the travel motor, including removing components like the motor head assembly, piston assemblies, springs, seals, and plates. Special care must be taken when removing or handling components with stored spring energy to avoid personal injury. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix NAH) Service Repair ...yin9niaojiao
This document provides the disassembly and assembly procedures for a travel motor on a Cat 336D2 excavator model. It lists 30 steps for disassembly, removing components like caps, springs, valves, plugs and seals. It then lists 30 steps for assembly, installing components like seals, pistons, bearings, springs and covers in the reverse order of disassembly. The document provides illustrations and notes for each step to ensure correct reassembly.
Caterpillar Cat 336D2, 336D2 L and 336D2 GC Excavator (Prefix FBT) Service Re...yin9niaojiao
This document provides instructions for removing and installing various engine components on a Caterpillar 336D2 excavator, including:
1) The engine oil filter and oil filter base.
2) The engine oil cooler.
3) The air cleaner assembly.
4) The turbocharger.
5) The water temperature regulator.
Detailed step-by-step instructions are provided for each component, along with illustrations to aid in the process. Safety notices are also included.
Caterpillar Cat 336D2 XE and 336D2 LXE Excavator (Prefix MFA) Service Repair ...yin9niaojiao
This document provides disassembly instructions for a 336D2 excavator travel motor. It outlines 27 steps to fully disassemble the travel motor. These include removing the motor head assembly, piston assemblies, barrel assembly, springs, seals, plates, and other internal components. Tools required include bolting fixtures, pry bars, pullers, and seal removal tools. Precautions are provided to retain component positioning for reassembly and to safely release spring forces during disassembly.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix MYG) Service Repair Manu...yin9niaojiao
This document provides instructions for disassembling and assembling the swing motor of 336D L and 336D LN excavators. The disassembly procedure involves 26 steps to remove components like the head, pistons, barrel, housing, seals and bearings. The assembly procedure reverses the disassembly steps and includes cleaning and inspecting parts, applying oil, and torquing bolts to the specified value. Proper tools and safety precautions are noted throughout to prevent injury from spring loaded parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix PPN) Service Repair Manu...yin9niaojiao
1. The document provides instructions for disassembling and assembling a piston pump used in Caterpillar 336D L and 336D LN excavators.
2. The disassembly procedure includes using various tools to remove over 30 individual parts from the pump in the correct order.
3. Reassembly requires carefully installing each part in the reverse order, ensuring proper placement and installation of seals, bearings, springs and other components. Temperatures must be controlled for some parts.
Caterpillar Cat 336D L and 336D LN Excavator (Prefix KDJ) Service Repair Manu...yin9niaojiao
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) used in Caterpillar 336D L and 336D LN excavators. It lists 22 steps for disassembly, removing various components like housing, springs, seals and bearings. The assembly section lists 30 steps to install these components in reverse order, noting that cleanliness is important and worn parts should be replaced. It also provides illustrations matching each step for clarity.
Caterpillar Cat 330F and 330F LN Excavator (Prefix HBT) Service Repair Manual...yin9niaojiao
This document provides instructions for removing and installing components related to the crankshaft and front cover of a Caterpillar 330F excavator engine. The procedures include removing and installing the crankshaft pulley, vibration damper, front seal, and heavy duty front cover. Tools required are listed for each procedure. Illustrations show the components and steps to disassemble and reassemble the assemblies.
This document provides installation instructions for a main hydraulic pump on a 330D excavator. It lists 54 steps to assemble components like pistons, gears, brackets, hoses and sensors. Tools include lever pullers, link brackets and torque wrenches. Precautions are given for spring loaded parts. The process involves lifting heavy components and ensuring proper hose, harness and bracket connections.
Caterpillar Cat 336D and 336D L Excavator (Prefix WRK) Service Repair Manual ...yin9niaojiao
The document provides instructions for removing and installing a final drive and travel motor on a Caterpillar 336D excavator. It lists required tools and gives step-by-step instructions involving disconnecting hoses, removing bolts and brackets, lifting out the assembly, and reinstalling it in reverse order. Safety notices are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix HER) Service Repair Manua...yin9niaojiao
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves 37 steps to remove all components of the final drive. Key steps include removing the final drive cover, gears, carrier assembly, planetary gears, and sprocket housing. The assembly process has 36 steps and involves installing components in reverse order while applying anti-seize compound and ensuring proper bearing preload using shims.
Caterpillar Cat 330D L Excavator (Prefix R2D) Service Repair Manual Instant D...yin9niaojiao
This document provides instructions for removing and installing the rear gear group and related components on a 330D L excavator with a C9 engine. The removal process involves using tools to remove bolts, gears, bushings, bearings, and covers. The installation process gives specifics on cleaning parts, applying adhesives, inserting bearings at the proper angles and depths, and torquing bolts. Tolerances are provided for correct installation of several components.
Caterpillar Cat 330D L Excavator (Prefix HAS) Service Repair Manual Instant D...yin9niaojiao
The document provides installation instructions for a swivel on an excavator. It describes removing the swivel by disconnecting hoses, removing bolts and lifting it out. It then details assembling the swivel by cleaning parts, installing seals and O-rings, positioning the housing over the rotor, and securing them with bolts. Finally, it describes installing the assembled swivel by connecting hoses and fittings and securing it with bolts.
Caterpillar Cat 330D2 and 330D2 L Excavator (Prefix FEX) Service Repair Manua...yin9niaojiao
The document provides instructions for disassembling a 330D2 excavator final drive. It involves 33 steps including removing the final drive cover, carrier assembly, planetary gears, ring gears, and other components. Various tools are required including link brackets, eyebolts, retaining ring pliers, and a transmission repair stand to support components weighing up to 550 kg during disassembly. Cleanliness is important to prevent dirt from entering internal mechanisms.
The document provides instructions for disassembling the final drive of a 330D MH EXCAVATOR. It lists 31 steps to completely disassemble the final drive assembly including removing gears, carriers, shafts, seals and housings. Various tools are required including retaining ring pliers, link brackets, eyebolts and forcing bolts to separate the components. Cleanliness is important to prevent dirt from entering during disassembly.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050091
Air Compressor Drive Gear - Remove
SMCS - 1803-011-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
Start By:
A. Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install Tooling (A) on the air compressor drive gear.
3. Remove nut (2) and washer (3) .
4. Remove air compressor drive gear (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:33:15 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050094
Air Compressor Drive Gear - Install
SMCS - 1803-012-GE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install air compressor drive gear (4) on the air compressor crankshaft.
3. Install washer (3) and nut (2) .
4. Install Tooling (A) on the air compressor drive gear.
5. Tighten nut (2) to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
6. Place a driver which is slightly larger than the nut over the nut and tap the driver with a
hammer.
7. Tighten the nut again to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
End By: Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:34:10 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01897971
Hydraulic System Pressure - Release - Forest Machines
SMCS - 3000-553; 4250-553; 4300-553; 5050-553
S/N - B1K1-UP
S/N - B2L1-UP
S/N - B3M1-UP
S/N - B4N1-UP
Pressure Release Procedure
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the following hydraulic circuits before any hydraulic
lines are disconnected or removed from that hydraulic circuit.
• Boom hydraulic circuit
• Stick hydraulic circuit
• Heel hydraulic circuit
• Grapple hydraulic circuit
• Swing hydraulic circuit
• Travel hydraulic circuit
• Attachment hydraulic circuits (if equipped)
• Pilot hydraulic circuit
• Return hydraulic circuit
1/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Refer to the Disassembly and Assembly Manual for additional information concerning
service of the components of specific hydraulic circuits.
Release Of Hydraulic Pressure From A Single Hydraulic
Circuit
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from a single hydraulic
circuit of the main hydraulic system.
1. Position the machine on level ground.
2/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that single hydraulic
circuit. This will also release any pressure that might be present in the pilot hydraulic
circuit.
Note: If the desired hydraulic circuit that requires service requires the activation of a switch
for operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Turn the engine start switch to the OFF position.
9. Slowly loosen the filler plug on the hydraulic tank and release the pressure from the
hydraulic tank. Leave the filler plug loose for a minimum of 45 seconds. This will release
the pressure that may be present in the return hydraulic circuit.
10. Tighten the filler plug on the hydraulic tank to the specified torque.
11. The pressure in the single hydraulic circuit that requires service is now released and lines
and components can be disconnected or removed from that hydraulic circuit.
Release Of Hydraulic Pressure From Multiple Hydraulic
Circuits
3/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from multiple hydraulic
circuits of the main hydraulic system.
1. Position the machine on level ground.
4/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that hydraulic circuit.
This will also release any pressure that might be present in the pilot hydraulic circuit.
Note: If the hydraulic circuit that requires service requires the activation of a switch for
operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Start the engine.
9. Place the hydraulic activation control lever in the UNLOCKED position. Do not move any
joysticks or pedals from the NEUTRAL position during this step. Do not activate any
switches during this Step.
10. Return the hydraulic activation control lever to the LOCKED position.
11. Shut off the engine.
12. Repeat Steps 4 through 11 for each additional hydraulic circuit that requires service.
13. After releasing the hydraulic pressure in each of the desired hydraulic circuits, place the
hydraulic activation control lever in the LOCKED position.
5/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 14. Turn the engine start switch to the OFF position.
15. Slowly loosen the filler plug on the hydraulic tank and release the pressure. Leave the filler
plug loose for a minimum of 45 seconds. This will release the pressure that may be present
in the return hydraulic circuit.
16. Tighten the filler plug on the hydraulic tank to the specified torque.
17. The pressure in the multiple hydraulic circuits that require service is now released and lines
and components can be disconnected or removed from those hydraulic circuits.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:35:33 UTC+0800 2020
6/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01694093
Battery - Remove and Install
SMCS - 1401-010
Removal Procedure
Note: This machine contains four batteries. The batteries are connected in series. Mark the
position of both the batteries and the battery cables prior to removal.
1. Open the rear access door on the left side of the machine.
Illustration 1 g00872239
2. Move the battery disconnect switch (1) to the OFF position.
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00872229
3. Remove nuts (2) from battery covers (3) .
4. Remove battery covers (3) .
Illustration 3 g00872255
5. Move rubber covers (4) from the battery terminal posts.
6. Remove the negative terminals from each of the batteries.
7. Remove the positive terminals from each of the batteries.
8. Remove the batteries.
Installation Procedure
Note: This machine contains four batteries. The batteries are connected in series. Each battery
MUST be in the correct position in order for correct machine operation.
1. Install the batteries in the correct position.
2. Install the positive terminals on each of the batteries.
3. Install the negative terminals on each of the batteries.
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g00872239
7. Move the battery disconnect switch (1) to the ON position.
8. Close the access door.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:36:28 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692348
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7113 Reverse Ratchet 1
1. Open the hood.
2. Disconnect the positive battery terminal. This will prevent any damage to the wiring or to
the alternator.
Illustration 1 g00871311
3. Disconnect wiring terminals (1), (2), and (3) from the alternator.
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00871323
4. Insert Tooling (A) in slot (4). Apply downward pressure in order to remove the belt.
Illustration 3 g00871363
5. Remove bolt (5) from the belt guard.
2/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 4 g00871375
6. Remove nut (6) and remove the bolt. Remove the guard.
Illustration 5 g00871388
7. Remove spacer (7) and bolt (8) .
8. Remove alternator (9) .
Installation Procedure
1. Place alternator (9) in position.
Illustration 6 g00871388
2. Install spacer (7) and bolt (8). Remove the alternator.
3/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 7 g00871375
3. Position the guard and install nut (6) .
Illustration 8 g00871363
4. Install bolt (5) in the belt guard.
Illustration 9 g00871323
5. Insert Tooling (A) in slot (4). Apply downward pressure in order to install the belt.
4/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 10 g00871311
6. Connect wiring terminals (1), (2), and (3) to the alternator.
7. Connect the positive battery terminal.
8. Close the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:37:24 UTC+0800 2020
5/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692671
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
1. Disconnect the battery cables.
Illustration 1 g00871495
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g00871498
2. Place an index mark on all of the electrical wires that are connected to the electric starting
motor. Disconnect the electrical wires from the electric starting motor.
Illustration 3 g00871501
3. Remove top starter bolt (1) .
Illustration 4 g00871506
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. 4. Remove bottom starter bolts (2) and use a hoist and a lifting sling to remove starter (3). The
weight of the starter is approximately 32 kg (70 lb).
Installation Procedure
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket on the electric starting motor.
Illustration 5 g00871506
3. Use a hoist and a lifting sling to position starter (3) and install bottom starter bolts (2). The
weight of the starter is approximately 32 kg (70 lb).
Illustration 6 g00871501
4. Install top starter bolt (1) .
3/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 7 g00871495
Illustration 8 g00871498
5. Connect all of the electrical wires to the electric starting motor by using the index marks.
6. Connect the battery cables.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:38:20 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692852
Fuel Filter (Primary) and Fuel Filter Base - Remove and
Install
SMCS - 1261-010; 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench As 1
B
6V-9508 Face Seal Plug (11/16 inch by 16 THD) 2
6V-9829 Cap Assembly (11/16 inch by16 THD) 2
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...