This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 320 c excavator (prefix jtg) service repair manual (jtg00001 ...ufjjsjekkeidol
The document provides instructions for assembling and disassembling components of a 320C excavator travel motor. The disassembly procedure involves removing 27 individual parts from the travel motor in 28 steps. The assembly procedure instructs assembling the travel motor components in reverse order. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...hhjsekmdmm
The document provides installation instructions for a swivel on an excavator. It describes cleaning the swivel parts, positioning the swivel using lifting tools, and installing fittings, hoses, bolts and covers to secure the swivel in place. Technicians are instructed to check o-rings and seals for wear and replace if needed, and to use clean hydraulic oil during assembly. The completed swivel installation is then checked for leaks using air pressure.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
This document provides assembly instructions for a piston pump in a 226B3 skid steer loader. It lists 78 steps to assemble internal components like bearings, seals, springs, and housing pieces. Tools required include rulers, pliers, drivers, pullers, and grease. Proper orientation of dowels, pins, and plates is emphasized. Torque specifications are provided for fittings and valves. The instructions caution that following the steps and wearing protective equipment is important due safety risks from spring-loaded components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 c fm excavator (prefix b1k) service repair manual (b1k000...hfjsekekmmd
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by describing the required tools and safety precautions. The instructions then detail how to position the piston, align the camshaft gear marks, apply lubricant to the camshaft, and insert the camshaft into the cylinder block. It concludes by stating to rotate the camshaft in both directions during installation to ensure proper movement.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat m317 f wheeled excavator (prefix f6p) service repair manual (...ifkkdmdmdm
This document provides instructions for disassembling and assembling the rear axle of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, roller bearings, brake discs, carrier gear, and hub. The assembly procedure instructs installing these 23 components in reverse order and provides torque specifications for tightening nuts. Tools required include retaining ring pliers, drivers, a spanner, pry bar, three jaw puller, and torque multiplier group.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
Caterpillar cat 320 c l 320cl excavator (prefix gla) service repair manual (...ujjdfjkskdme
The document provides instructions for disassembling a swing drive component from an excavator. It involves 29 steps, including removing gears, carriers, retaining rings, seals and other parts from the housing. Cleanliness is important to prevent contaminating the hydraulic system. Tools include retaining ring pliers, drivers and presses. The process separates all internal components to allow inspection and replacement of parts.
The document provides instructions for disassembling and assembling the final drive of an excavator. It lists the necessary tools and parts. The 27 step disassembly process removes components like gears, shafts, seals and housings. The 36 step assembly process installs these components in reverse order, noting that cleanliness is important and new seals and shims should be used. Precise alignment of parts and use of press tools are required to reassemble the final drive.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...hhjsekmdmm
The document provides instructions for removing and disassembling the final drive, travel motor, and swivel components of an excavator. It outlines 13 steps to remove the final drive and travel motor assembly using tools like a lever puller and vacuum pump. It then describes 11 steps to reinstall the components and refill fluids. Finally, it lists 5 steps to disassemble the swivel joint, including using bolts and washers to separate the housing from the rotor.
Caterpillar cat 330 c l excavator (prefix cap) service repair manual (cap0000...jfdskekdmme
This document provides instructions for disassembling and assembling the final drive component of a 330C excavator model. It lists over 30 detailed steps for disassembly, removing parts like gears, bearings, seals, and housings. Similarly, it lists over 20 detailed steps for assembly, including applying compounds, installing seals and bearings, and pressing components together using various tools. The goal is to disassemble the entire final drive assembly into individual parts and then reassemble all parts back into the final drive assembly. Cleanliness is emphasized throughout to prevent damage during assembly.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
This document provides instructions for removing the lift cylinders and lift arms from a 228 Skid Steer Loader. The procedure involves:
1. Releasing hydraulic pressure and tilting the cab
2. Disconnecting hydraulic lines and electrical harnesses from the lift arms
3. Using retaining ring pliers to remove pins and rings, releasing the lift cylinders from the arms
4. Removing additional pins and braces to allow removal of the lift cylinders and arms
Safety precautions are provided regarding hydraulic pressure, and marks should be made on lines and cylinders before removal.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat m317 f wheeled excavator (prefix f6p) service repair manual (...ifkkdmdmdm
This document provides instructions for disassembling and assembling the rear axle of an M317F wheeled excavator. The disassembly procedure involves removing 23 components including carrier housing, planetary gears, thrust washers, retaining rings, roller bearings, brake discs, carrier gear, and hub. The assembly procedure instructs installing these 23 components in reverse order and provides torque specifications for tightening nuts. Tools required include retaining ring pliers, drivers, a spanner, pry bar, three jaw puller, and torque multiplier group.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. It also describes instructions for removing and installing the quick coupler on the skid steer loader. This involves removing pins and bolts to detach the coupler and lifting it off, then reversing the process to install it.
3. Finally, it provides steps for removing and installing the tilt cylinder, which requires removing pins and bolts to detach it from the lift arm assembly and reattaching it by reversing the removal steps.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader before performing maintenance. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. Steps are provided to remove and install the quick coupler on the skid steer loader. This involves supporting the coupler, removing pins and bolts, and using lifting devices during removal and installation.
3. Procedures describe removing the tilt cylinder from the lift arm assembly of the skid steer loader. This involves removing snap rings and pins, raising the lift arm with supports, and disconnecting hydraulic lines before removing the cylinder.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are outlined to prevent injury from hydraulic pressure and contain fluids during disassembly.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are provided to prevent injury from hydraulic pressure and contain fluids during disassembly.
Similar to Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m00001 and up) (13)
Caterpillar cat m315 c wheeled excavator (prefix h2b) service repair manual (...jfdjskmdmme
The document provides instructions for disassembling the piston pump of a M315C wheeled excavator. It describes removing 31 individual parts from the pump in a specific sequence, including the servo valve, charge pump, gears, head, relief valves, pistons, barrel assembly, swashplate assembly, and other components. Cleanliness is important during disassembly to prevent dirt from entering the internal mechanisms. Personal injury can result from hydraulic pressure still remaining in the system, so precautions are described.
Caterpillar cat m315 c wheeled excavator (prefix bdm) service repair manual (...jfdjskmdmme
This document provides instructions for disassembling and assembling the main hydraulic pump of a M315C wheeled excavator. It lists 42 steps to disassemble the pump by removing components like valves, springs, seals, pistons, and bearings. It then lists the assembly steps in reverse order, noting to clean parts and apply new thread lock before reinstalling components. Precautions are provided to mark parts for orientation and contain fluids during maintenance.
Caterpillar cat 330 d2 l excavator (prefix xdr) service repair manual (xdr000...jfdjskmdmme
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 330 d2 l excavator (prefix hsp) service repair manual (hsp000...jfdjskmdmme
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids during disassembly.
Caterpillar cat 330 d2 l excavator (prefix her) service repair manual (her000...jfdjskmdmme
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d2 l excavator (prefix fex) service repair manual (fex000...jfdjskmdmme
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
Caterpillar cat 330 d2 l excavator (prefix ex7) service repair manual (ex7000...jfdjskmdmme
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function of the travel motor.
Caterpillar cat 330 d2 l excavator (prefix ebp) service repair manual (ebp000...jfdjskmdmme
The document provides instructions for disassembling an excavator travel motor. It begins by having the technician remove the travel motor from the excavator. The disassembly instructions then detail 27 steps to fully disassemble the travel motor. These include removing components like the motor head, brake piston, barrel assembly, cam plate, and shaft assembly. Throughout the process, technicians are warned to take care with components and contain any fluids.
Caterpillar cat 330 d2 l excavator (prefix dtg) service repair manual (dtg000...jfdjskmdmme
The document provides the disassembly procedure for a 330D2 excavator travel motor in 28 steps. It begins by instructing the technician to clean and secure the travel motor vertically, then remove the head by taking out bolts and marking parts for reassembly. Several internal components are then removed, including brake pistons, plates, and seals. The rotating assembly is separated from the housing using a prybar. Bearings and seals are removed from the shaft. Finally, the cam plate, pistons, seals and other remaining parts are disassembled from the housing. Throughout, precise steps and illustrations are provided to guide disassembly while maintaining part orientation.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing components like the motor head, brake piston, rotating assembly, cam plate, piston assemblies and seals. Special tools are required for tasks like removing retaining rings and bearing races. Technicians are advised to mark components for proper reinstallation and contain any fluids removed from the motor.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves removing 37 individual parts in a specific sequence using various tools. The assembly process reverses the disassembly steps and provides additional details on setting the bearing preload and installing seals correctly.
The document provides instructions for disassembling a final drive assembly in 3 steps:
1. Remove the final drive assembly and disassemble it by removing the cover, gears, carrier assembly, planetary gears, and ring gear.
2. Disassemble the planetary carrier by removing the planetary shafts, washers, and gears.
3. Remove the ring gear from the sprocket housing and disassemble the motor housing by removing coupling gear, shims, and seals.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure reverses this process and puts the travel motor back together in 25 steps, reinstalling the parts in the reverse order that they were removed. Precise instructions are given for each step to ensure correct reassembly.
The document provides disassembly instructions for a 330D2 and 330D2 L excavator travel motor in 28 steps. It begins by having the technician thoroughly clean and secure the travel motor vertically before disassembling. The steps then carefully describe removing components like the head, brake piston, plates, seals, bearings, and more. Pictures accompany each step to illustrate the proper procedure. Safety notices are included to handle fluids and springs carefully.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...jfdjskmdmme
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. This includes removing covers, gears, shafts, bearings, seals and other components. Special tools are required to remove some parts, and safety notes are provided about cleanliness and part weights which require multiple people to handle. The overall goal is to break the final drive down into all of its individual parts for repair or replacement.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...jfdjskmdmme
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations supplement the written instructions.
3. Proper cleaning and application of sealant or retaining compound is emphasized to prevent contamination and ensure proper component life.
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...jfdjskmdmme
The document provides disassembly instructions for a final drive on an excavator model 330D L excavator. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing the cover, gears, plates, plugs, seals, carrier assembly, planetary gear assembly, shafts, springs, and bearings. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050091
Air Compressor Drive Gear - Remove
SMCS - 1803-011-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
Start By:
A. Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install Tooling (A) on the air compressor drive gear.
3. Remove nut (2) and washer (3) .
4. Remove air compressor drive gear (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:33:15 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050094
Air Compressor Drive Gear - Install
SMCS - 1803-012-GE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install air compressor drive gear (4) on the air compressor crankshaft.
3. Install washer (3) and nut (2) .
4. Install Tooling (A) on the air compressor drive gear.
5. Tighten nut (2) to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
6. Place a driver which is slightly larger than the nut over the nut and tap the driver with a
hammer.
7. Tighten the nut again to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
End By: Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:34:10 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01897971
Hydraulic System Pressure - Release - Forest Machines
SMCS - 3000-553; 4250-553; 4300-553; 5050-553
S/N - B1K1-UP
S/N - B2L1-UP
S/N - B3M1-UP
S/N - B4N1-UP
Pressure Release Procedure
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the following hydraulic circuits before any hydraulic
lines are disconnected or removed from that hydraulic circuit.
• Boom hydraulic circuit
• Stick hydraulic circuit
• Heel hydraulic circuit
• Grapple hydraulic circuit
• Swing hydraulic circuit
• Travel hydraulic circuit
• Attachment hydraulic circuits (if equipped)
• Pilot hydraulic circuit
• Return hydraulic circuit
1/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Refer to the Disassembly and Assembly Manual for additional information concerning
service of the components of specific hydraulic circuits.
Release Of Hydraulic Pressure From A Single Hydraulic
Circuit
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from a single hydraulic
circuit of the main hydraulic system.
1. Position the machine on level ground.
2/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that single hydraulic
circuit. This will also release any pressure that might be present in the pilot hydraulic
circuit.
Note: If the desired hydraulic circuit that requires service requires the activation of a switch
for operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Turn the engine start switch to the OFF position.
9. Slowly loosen the filler plug on the hydraulic tank and release the pressure from the
hydraulic tank. Leave the filler plug loose for a minimum of 45 seconds. This will release
the pressure that may be present in the return hydraulic circuit.
10. Tighten the filler plug on the hydraulic tank to the specified torque.
11. The pressure in the single hydraulic circuit that requires service is now released and lines
and components can be disconnected or removed from that hydraulic circuit.
Release Of Hydraulic Pressure From Multiple Hydraulic
Circuits
3/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from multiple hydraulic
circuits of the main hydraulic system.
1. Position the machine on level ground.
4/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that hydraulic circuit.
This will also release any pressure that might be present in the pilot hydraulic circuit.
Note: If the hydraulic circuit that requires service requires the activation of a switch for
operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Start the engine.
9. Place the hydraulic activation control lever in the UNLOCKED position. Do not move any
joysticks or pedals from the NEUTRAL position during this step. Do not activate any
switches during this Step.
10. Return the hydraulic activation control lever to the LOCKED position.
11. Shut off the engine.
12. Repeat Steps 4 through 11 for each additional hydraulic circuit that requires service.
13. After releasing the hydraulic pressure in each of the desired hydraulic circuits, place the
hydraulic activation control lever in the LOCKED position.
5/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 14. Turn the engine start switch to the OFF position.
15. Slowly loosen the filler plug on the hydraulic tank and release the pressure. Leave the filler
plug loose for a minimum of 45 seconds. This will release the pressure that may be present
in the return hydraulic circuit.
16. Tighten the filler plug on the hydraulic tank to the specified torque.
17. The pressure in the multiple hydraulic circuits that require service is now released and lines
and components can be disconnected or removed from those hydraulic circuits.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:35:33 UTC+0800 2020
6/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01694093
Battery - Remove and Install
SMCS - 1401-010
Removal Procedure
Note: This machine contains four batteries. The batteries are connected in series. Mark the
position of both the batteries and the battery cables prior to removal.
1. Open the rear access door on the left side of the machine.
Illustration 1 g00872239
2. Move the battery disconnect switch (1) to the OFF position.
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00872229
3. Remove nuts (2) from battery covers (3) .
4. Remove battery covers (3) .
Illustration 3 g00872255
5. Move rubber covers (4) from the battery terminal posts.
6. Remove the negative terminals from each of the batteries.
7. Remove the positive terminals from each of the batteries.
8. Remove the batteries.
Installation Procedure
Note: This machine contains four batteries. The batteries are connected in series. Each battery
MUST be in the correct position in order for correct machine operation.
1. Install the batteries in the correct position.
2. Install the positive terminals on each of the batteries.
3. Install the negative terminals on each of the batteries.
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g00872239
7. Move the battery disconnect switch (1) to the ON position.
8. Close the access door.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:36:28 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692348
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7113 Reverse Ratchet 1
1. Open the hood.
2. Disconnect the positive battery terminal. This will prevent any damage to the wiring or to
the alternator.
Illustration 1 g00871311
3. Disconnect wiring terminals (1), (2), and (3) from the alternator.
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00871323
4. Insert Tooling (A) in slot (4). Apply downward pressure in order to remove the belt.
Illustration 3 g00871363
5. Remove bolt (5) from the belt guard.
2/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 4 g00871375
6. Remove nut (6) and remove the bolt. Remove the guard.
Illustration 5 g00871388
7. Remove spacer (7) and bolt (8) .
8. Remove alternator (9) .
Installation Procedure
1. Place alternator (9) in position.
Illustration 6 g00871388
2. Install spacer (7) and bolt (8). Remove the alternator.
3/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 7 g00871375
3. Position the guard and install nut (6) .
Illustration 8 g00871363
4. Install bolt (5) in the belt guard.
Illustration 9 g00871323
5. Insert Tooling (A) in slot (4). Apply downward pressure in order to install the belt.
4/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 10 g00871311
6. Connect wiring terminals (1), (2), and (3) to the alternator.
7. Connect the positive battery terminal.
8. Close the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:37:24 UTC+0800 2020
5/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692671
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
1. Disconnect the battery cables.
Illustration 1 g00871495
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g00871498
2. Place an index mark on all of the electrical wires that are connected to the electric starting
motor. Disconnect the electrical wires from the electric starting motor.
Illustration 3 g00871501
3. Remove top starter bolt (1) .
Illustration 4 g00871506
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 4. Remove bottom starter bolts (2) and use a hoist and a lifting sling to remove starter (3). The
weight of the starter is approximately 32 kg (70 lb).
Installation Procedure
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket on the electric starting motor.
Illustration 5 g00871506
3. Use a hoist and a lifting sling to position starter (3) and install bottom starter bolts (2). The
weight of the starter is approximately 32 kg (70 lb).
Illustration 6 g00871501
4. Install top starter bolt (1) .
3/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 7 g00871495
Illustration 8 g00871498
5. Connect all of the electrical wires to the electric starting motor by using the index marks.
6. Connect the battery cables.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:38:20 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692852
Fuel Filter (Primary) and Fuel Filter Base - Remove and
Install
SMCS - 1261-010; 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench As 1
B
6V-9508 Face Seal Plug (11/16 inch by 16 THD) 2
6V-9829 Cap Assembly (11/16 inch by16 THD) 2
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...