This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 330 c l excavator (prefix mkm) service repair manual (mkm0000...hhjsekmdmm
This document provides instructions for disassembling and assembling the travel motor of a 330C excavator. It begins by listing the required tools. The disassembly process is then described in 28 steps, removing components like the head, springs, plates, and seals. The assembly section follows the reverse order in 23 steps, applying thread lock and ensuring proper alignment of parts. Precautions are provided to prevent damage and ensure cleanliness during the process.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...hhjsekmdmm
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...hhjsekmdmm
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key components that are disassembled include the drive housing, planetary gear assemblies, ring gear, carrier assemblies, and individual planet gears. Tools required include link brackets and forcing bolts to remove components. Safety notes are provided to clean parts before disassembly and have two people assist with heavier components.
This document provides instructions for disassembling and assembling the final drive of a 330D2 excavator. The disassembly process involves using various tools to remove 37 individual parts from the final drive assembly. The assembly process similarly uses tools to reinstall the parts in the reverse order, ensuring proper installation of seals and adjusting bearing preload through precise shimming.
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...hhjsekmdmm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a 330D L excavator. The removal procedure involves using various tools to remove bolts, gears, bushings, bearings, and covers. Precautions are listed to keep parts clean and prevent damage. The installation procedure specifies how to position gears, bearings, seals and other components, applying threadlock and noting torque specifications. Dimensions and angles are provided to ensure proper installation of bearings.
Caterpillar cat 336 d2 l excavator (prefix zct) service repair manual (zct000...fjjskekdm
The document provides instructions for disassembling and assembling the main hydraulic pump of a 336D2 L excavator. It lists 51 steps to fully disassemble the pump by removing components like valves, springs, pistons, seals, and bearings. The assembly section lists 13 steps, including installing bearings, covers, pins and pistons back into their original positions. Precautions are provided for working with pressurized springs. Required specialty tools are also listed.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...hhjsekmdmm
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper alignment and torque specifications are noted throughout.
The document provides the disassembly procedure for a 330D2 excavator travel motor. It lists 28 steps to fully disassemble the travel motor, including removing the head, brake piston, plates and discs, rotating assembly, seals, and other internal components. Tools required are also listed. The procedure aims to clearly identify each part and ensure proper reinstallation of components in their original positions and orientations.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing the motor head, brake piston, rotating assembly, cam plate, piston assemblies and other internal components. Tools required include an adapter, bolts, eyebolt, retaining ring pliers, bearing puller, and other equipment to securely hold parts during disassembly. Safety precautions are noted such as containing fluids and ensuring air pressure is free of water.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
Caterpillar cat 330 c l excavator (prefix jab) service repair manual (jab0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C and 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing components back in reverse order and noting proper installation of seals, springs, and other parts.
The document provides instructions for disassembling and assembling a travel motor. It is a service repair manual for Caterpillar 330D2 and 330D2 L excavators. The disassembly procedure involves removing 28 different parts from the travel motor in 27 steps. The assembly procedure involves installing the parts in the reverse order over 23 steps. Precise alignment and cleanliness of parts is emphasized to ensure proper function.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m000...hhjsekmdmm
This document contains instructions for removing and installing various components on a 330C FM Excavator including:
1) The air compressor drive gear which involves removing a nut, washer and gear from the air compressor.
2) Releasing hydraulic pressure from single or multiple circuits by moving components and levers to release pressure before disconnecting lines.
3) Removing the batteries which requires disconnecting cables and removing covers.
4) Removing the alternator which involves disconnecting wiring, removing a belt with a tool, and removing a bolt from a guard.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...hhjsekmdmm
1. The document provides removal and installation instructions for the rear gear group, flywheel, and crankshaft rear seal of a 330D L excavator powered by a C9 engine.
2. Detailed step-by-step instructions are given, including the required tools and torque specifications. Illustrations are provided to supplement the text instructions.
3. Proper cleaning, inspection, and use of locking compounds are emphasized to ensure correct installation and prevent premature wear of components.
Caterpillar cat 330 c l excavator (prefix kdd) service repair manual (kdd0000...hhjsekmdmm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of a 330C L excavator.
2) It lists 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components.
3) It then lists 28 steps for assembly, placing the components back in reverse order and noting proper installation of seals, springs, and other parts.
The document provides instructions for disassembling a 330D2 excavator travel motor. It is a 28 step process that includes removing the motor head, brake piston, rotating assembly, cam plate, piston assemblies and other internal components. Tools required include an adapter, bolts, eyebolt, retaining ring pliers, bearing puller, and other equipment to securely hold parts during disassembly. Safety precautions are noted such as containing fluids and ensuring air pressure is free of water.
Caterpillar cat 374 d l excavator (prefix pja) service repair manual (pja0000...fjkskedmme
This document provides instructions for disassembling and assembling the final drive of a 374D L excavator. It lists over 30 detailed steps for removing components like the ring gear, carrier assemblies, gears, shafts and seals. Bearing preload is determined by applying specific pressures and measuring clearances with a micrometer. All components must be thoroughly cleaned before precise reassembly in their original locations using torque wrenches and lifting devices, with seals and threaded surfaces coated in locking compound or adhesive.
Caterpillar cat 315 d l excavator (prefix kbd) service repair manual (kbd0000...fjskefkemms
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves removing over 30 individual parts including the carrier assembly, ring gears, sun gear, planetary gears, and seals. The assembly process reverses the disassembly steps and provides details on installing new seals, bearings, and determining the correct shim thickness. Proper cleaning and use of installation tools are emphasized throughout.
Caterpillar cat 16 h motor grader (prefix ats) service repair manual (ats0000...fjskefkemms
This document provides disassembly instructions for the transmission and transfer gears of a 16H Motor Grader. It lists over 60 steps and required tools to disassemble components such as the transmission control module, planetary group, sleeves, gears, bearings, seals, and housing. Detailed illustrations accompany each step to show how to remove parts and subassemblies like the gear pump, coupling assembly, manifold, and housing. Safety precautions are provided for steps involving compressed springs.
Caterpillar cat 330 d excavator (prefix jjm) service repair manual (jjm00001 ...jfdskekdmme
This document provides instructions for disassembling and assembling the travel motor on a 330D excavator. It lists the required tools and presents step-by-step procedures to remove and install various components of the travel motor like the head, brake piston, plates, seals, and bearings. Cleanliness is emphasized during disassembly and assembly to prevent contamination. All O-rings and gaskets must be replaced.
Caterpillar cat 323 f ln excavator (prefix yec) service repair manual (yec000...fjjskekdmme
This service repair manual provides instructions for assembling the final drive of a 323F LN Excavator. It outlines 37 steps requiring various tools to install bearings, seals, gears, pins, and other components in the proper order. Proper preloading of bearings is important. Gaskets and seals must be clean and lubricated before installation. Weights of individual components are provided to assist with assembly. Upon completion, the final drive is installed on the excavator.
Caterpillar cat 330 f excavator (prefix hbt) service repair manual (hbt00001 ...fjskekdmjekm
This document provides instructions for removing and installing a front cover on a 330F excavator engine. The key steps are:
1. Remove the crankshaft pulley, fan if equipped, and front seal from the front cover.
2. Remove bolts from the front cover and housing, then remove the cover and gasket.
3. Clean the cover, housing, and install a new gasket. Use guide studs to position the cover and hand tighten bolts.
4. Align the cover and tighten the bolts. Install a new front seal. Reinstall the pulley, fan if equipped.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 e l excavator (prefix tdw) service repair manual (tdw0000...fjskefkemms
This document provides assembly and disassembly instructions for a swing drive on excavator models 323E L, 323E LN, and 323E SA. It includes 21 steps for disassembly and 18 steps for assembly. Key steps include using retaining ring pliers and pullers to remove gears, carriers, shafts, and seals from the housing. Assembly involves pressing components back into place, applying threadlocker, and torquing bolts to specifications. The document provides detailed illustrations and lists required tools for each step.
Caterpillar cat 330 c fm excavator (prefix b2l) service repair manual (b2l000...fjsjekdmmeme
This document provides instructions for removing and installing the cylinder head and camshaft on a Caterpillar 330C FM excavator equipped with a C-9 engine. The removal procedure involves draining coolant, removing various components attached to the cylinder head like the alternator and valve cover, then using lifting tools to remove the cylinder head and gasket. The installation procedure outlines reinstalling the gasket and cylinder head, reattaching all components and refilling the cooling system. Similarly, the camshaft removal involves setting piston timing, removing gears and thrust plate, while installation requires lubricating and inserting the camshaft ensuring proper timing of gears.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 330 l excavator (prefix 8fk) service repair manual (8fk00001 ...fjsjekdmmeme
This document provides instructions for removing and installing a cylinder head on a 330L excavator with a 3306 engine. The key steps are:
1. Remove components attached to the cylinder head like the exhaust manifold, fuel lines, and rocker shaft.
2. Remove the cylinder head bolts and lifting the heavy cylinder head off the engine.
3. Clean the mating surfaces and install a new gasket before reinstalling the cylinder head and torquing the bolts in the specified sequence.
4. Reinstall the removed components like the rocker shaft after installing the new cylinder head.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...shudun96087
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits before servicing lines or components
- Removing and installing the air compressor drive gear
- Removing and installing batteries
- Removing and installing the alternator
It describes the required tools, safety precautions, illustrated steps, and torque specifications for each job. Releasing hydraulic pressure properly is emphasized to prevent injury from high pressure lines.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...cnp692569
This document provides instructions for removing and installing components on a 330C FM Excavator, including:
- Releasing hydraulic pressure from single and multiple circuits safely before disconnecting lines or removing components.
- Removing and installing the air compressor drive gear by mounting the compressor, removing/installing hardware, and tightening to the specified torque.
- Removing the alternator by disconnecting wiring, using a tool to remove the belt, and removing a bolt from the belt guard.
- Removing and installing batteries by moving the disconnect switch to off, removing covers and terminals, and reinstalling in the correct positions.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...kesi7153062
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing maintenance or repairs. It describes:
- Releasing pressure from a single circuit by moving its control joystick or pedal to the full stroke position with the engine off and activation lever unlocked.
- Releasing pressure from multiple circuits by starting the engine briefly with the activation lever unlocked and controls in neutral, then stopping it.
- Positioning the excavator's boom, stick, and bucket flat on the ground first to avoid movement.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove snap rings and pins from the front of each lift cylinder.
4. Disconnect lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing the tilt cylinder from a Caterpillar 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
This document provides instructions for removing the tilt cylinder from a 226 Skid Steer Loader. The key steps are:
1. Release hydraulic pressure and remove the quick coupler.
2. Support the rear of the machine with jack stands.
3. Remove the snap ring and pin from the front of each tilt cylinder.
4. Disconnect the lines from each tilt cylinder and remove bolts and pins to separate the cylinder.
This document provides instructions for removing and installing the tilt cylinder on a 226 Skid Steer Loader. The removal procedure involves releasing hydraulic pressure, removing pins and bolts to separate the cylinder from the lift arm assembly. The installation procedure describes reattaching the cylinder using bolts, pins and reconnecting hydraulic lines. Safety precautions are provided regarding hydraulic pressure and fluid containment.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. It also describes instructions for removing and installing the quick coupler on the skid steer loader. This involves removing pins and bolts to detach the coupler and lifting it off, then reversing the process to install it.
3. Finally, it provides steps for removing and installing the tilt cylinder, which requires removing pins and bolts to detach it from the lift arm assembly and reattaching it by reversing the removal steps.
1. The document provides instructions for releasing hydraulic pressure on a 216 Skid Steer Loader before performing maintenance. It describes pressing the auxiliary hydraulic control switch while the joystick is in neutral to release pressure from the auxiliary system.
2. Steps are provided to remove and install the quick coupler on the skid steer loader. This involves supporting the coupler, removing pins and bolts, and using lifting devices during removal and installation.
3. Procedures describe removing the tilt cylinder from the lift arm assembly of the skid steer loader. This involves removing snap rings and pins, raising the lift arm with supports, and disconnecting hydraulic lines before removing the cylinder.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are outlined to prevent injury from hydraulic pressure and contain fluids during disassembly.
1. The document provides instructions for removing a lift cylinder from a 216 Skid Steer Loader.
2. It describes releasing hydraulic pressure, tilting the cab, and removing pins and bolts to detach the lift cylinder.
3. Safety precautions are provided to prevent injury from hydraulic pressure and contain fluids during disassembly.
Similar to Caterpillar cat 330 c fm excavator (prefix b3m) service repair manual (b3m00001 and up) (13)
Caterpillar cat 330 d l mobile hydraulic excavator (prefix h3d) service repai...diskdkkdmmd
This document provides instructions for removing and installing a crankshaft rear seal on a 330D L excavator. The removal procedure involves removing the flywheel and then removing the crankshaft rear seal and bolts. The installation procedure specifies cleaning and preparing surfaces, applying sealant, and installing the seal with bolts in a specified tightening sequence. Tools and inspection guidelines are also referenced.
Caterpillar cat 330 d l excavator (prefix thj) service repair manual (thj0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 330 d l excavator (prefix r2d) service repair manual (r2d0000...diskdkkdmmd
This document provides instructions for removing and installing various components of the rear gear group and flywheel on a Caterpillar 330D L excavator with a C9 engine. The summary is:
The rear gear group removal procedure involves using tools to remove retaining bolts, bushings, adapters, bearings, gears and covers. Installation requires matching dimensions and orientations when pressing in new bearings and reinstalling components.
To remove the flywheel, bolts are first removed 180 degrees apart using a guide stud before lifting the flywheel off. Installation involves heating and pressing in a ring gear, lifting the flywheel into place using guide studs, and torquing bolts to the specified value
Caterpillar cat 330 d l excavator (prefix nbd) service repair manual (nbd0000...diskdkkdmmd
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d l excavator (prefix mwp) service repair manual (mwp0000...diskdkkdmmd
This document provides disassembly and assembly instructions for a 330D L excavator final drive. It lists required tools and steps to remove the travel motor, drain oil, remove the final drive sprocket, cover, carrier assemblies, springs and other components. Detailed illustrations accompany each step to disassemble the planetary gear assemblies, shafts, rings, and other parts of the final drive. Proper safety procedures are noted to relieve spring pressure before removing retaining rings.
Caterpillar cat 330 d l excavator (prefix lrm) service repair manual (lrm0000...diskdkkdmmd
The document provides instructions for removing and installing the final drive and travel motor assembly on an excavator. Key steps include:
1. Removing hydraulic hoses and fittings, separating the track, and using a lever puller and vacuum pump to remove the assembly.
2. Lifting the assembly free using lifting brackets and bolts.
3. Removing sealing rings and the counterbalance valve.
4. Reinstalling involves the reverse of removal steps, including applying anti-seize compound and tightening bolts to the specified torque.
Caterpillar cat 330 d l excavator (prefix jlp) service repair manual (jlp0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. The steps include removing covers, gears, shafts, seals, and other components. Special tools are required for tasks like removing retaining rings and carrier assemblies. Safety notes are included to clean parts thoroughly before disassembly to prevent dirt intrusion.
Caterpillar cat 330 d l excavator (prefix has) service repair manual (has0000...diskdkkdmmd
The document provides instructions for assembling a swivel component. It describes cleaning the parts thoroughly before assembly and inspecting O-rings and seals for wear. The assembly process involves installing seals and O-rings into the outside housing, positioning the rotor inside the housing, and attaching the housing to the rotor with bolts and washers. Proper cleanliness is emphasized throughout the assembly.
Caterpillar cat 330 d l excavator (prefix gbc) service repair manual (gbc0000...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It outlines the required tools and steps to take the camshaft out of the cylinder block, including removing other components like the rocker arm shaft and front cover first. It then describes how to install the camshaft, making sure to lubricate the lobes and journals and rotate the camshaft to prevent binding. Proper alignment of timing marks is also emphasized when installing the camshaft.
Caterpillar cat 330 d l excavator (prefix ern) service repair manual (ern0000...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive including removing covers, gears, carriers, shafts, seals and housings. Special tools are required including link brackets and forcing bolts to remove components due to their weight, with some parts weighing up to 550kg. Detailed illustrations accompany each step to show how to disassemble the various components.
Caterpillar cat 330 d l excavator (prefix edx) service repair manual (edx0000...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar cat 330 d l excavator (prefix eah) service repair manual (eah0000...diskdkkdmmd
This document provides instructions for disassembling and assembling the swing drive of 330D and 330D L excavator models. The disassembly procedure involves removing 17 total parts from the swing drive including covers, gears, carriers, shafts and seals. The assembly procedure instructs installing these 17 parts in reverse order and includes cleaning and lubricating components before assembly. Tools required include link brackets, nylon slings and pliers.
Caterpillar cat 330 d fm excavator (prefix l2k) service repair manual (l2k000...diskdkkdmmd
This document provides installation instructions for a travel motor on a 330D FM excavator. It includes:
- Cleaning the mating surfaces of the travel motor and final drive.
- Using guide bolts and lifting devices to position the travel motor, then installing securing bolts.
- Connecting hose assemblies and tightening to the specified torque.
- Using guide bolts and two people to position the heavy cover, then installing and tightening cover bolts.
Caterpillar cat 330 d fm excavator (prefix e4k) service repair manual (e4k000...diskdkkdmmd
This document provides disassembly instructions for the final drive of a 330D FM excavator. It lists required tools and outlines 33 steps to fully disassemble the final drive. These include removing the travel motor, draining oil, removing the sprocket, cover, carrier assemblies, gears, springs and other components. Detailed illustrations are provided to show how to remove retaining rings, shafts, plates and other parts using various specialty tools. Safety precautions are noted regarding relieving spring pressure and containing fluids.
Caterpillar cat 330 d excavator (prefix thj) service repair manual (thj00001 ...diskdkkdmmd
The document provides disassembly instructions for a final drive on an excavator model 330D L. It involves removing 32 components in 31 steps, starting with removing the final drive and travel motor. Key steps include removing gears, carriers, shafts, seals and housings using various tools like link brackets, forcing bolts, and presses. Cleanliness is important to prevent dirt from entering during reassembly.
Caterpillar cat 330 d excavator (prefix nbd) service repair manual (nbd00001 ...diskdkkdmmd
This document provides disassembly instructions for a final drive on excavator models 330D and 330D L. The procedure involves 32 steps and requires various tools. Key steps include removing the final drive cover, gears, carrier assembly, planetary gear assembly, and housing components. Disassembly of the planetary gear assembly requires pressing out shafts and removing individual parts like springs pins, washers, bearings, and gears. Cleanliness is important during disassembly to prevent dirt from entering internal mechanisms.
Caterpillar cat 330 d excavator (prefix gbc) service repair manual (gbc00001 ...diskdkkdmmd
This document provides instructions for removing and installing a camshaft on a Caterpillar C9 engine. It describes:
1) Removing the rocker arm shaft, front cover, and valve lifters before removing the camshaft.
2) Aligning timing marks and removing bolts and thrust plate to access the camshaft.
3) Lubricating and carefully installing the camshaft, rotating it to prevent binding in the bearings.
Caterpillar cat 330 d excavator (prefix ern) service repair manual (ern00001 ...diskdkkdmmd
This document provides disassembly instructions for a final drive on an excavator model 330D L. It outlines 32 steps to fully disassemble the final drive. Key steps include removing the final drive cover, gears, carrier assemblies, planetary gear assemblies, and ring gear. Proper safety equipment and lifting devices are required due to the heavy weights involved, such as the 550 kg total weight of the entire final drive assembly. Cleanliness is important to prevent dirt from entering during disassembly.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...diskdkkdmmd
The document provides instructions for assembling and installing the swing drive of an excavator. It describes applying sealant and installing bearings, gears, housing components, and fasteners in the proper sequence. The assembled swing drive is then installed on the excavator frame using lifting equipment and bolted into place with an alternating tightening pattern to the specified torque.
Caterpillar cat 330 d excavator (prefix eah) service repair manual (eah00001 ...diskdkkdmmd
This document provides instructions for disassembling and assembling the swing drive of excavator models 330D and 330D L. The disassembly procedure involves removing 17 parts from the swing drive including the cover, carrier assemblies, gears, and housing. The assembly procedure describes installing these 17 parts in the reverse order and includes cleaning, lubricating, and setting components into place using various tools. Proper cleaning and lubrication of parts is emphasized for correct reassembly.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050091
Air Compressor Drive Gear - Remove
SMCS - 1803-011-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
Start By:
A. Remove the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install Tooling (A) on the air compressor drive gear.
3. Remove nut (2) and washer (3) .
4. Remove air compressor drive gear (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:33:15 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
C9
Engine For Caterpillar Built Machines
Media Number -SENR9502-16 Publication Date -01/03/2014 Date Updated -06/03/2014
i02050094
Air Compressor Drive Gear - Install
SMCS - 1803-012-GE
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 132-5451 Holding Fixture 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. Illustration 1 g00634494
1. Mount air compressor (1) in a bench vise.
2. Install air compressor drive gear (4) on the air compressor crankshaft.
3. Install washer (3) and nut (2) .
4. Install Tooling (A) on the air compressor drive gear.
5. Tighten nut (2) to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
6. Place a driver which is slightly larger than the nut over the nut and tap the driver with a
hammer.
7. Tighten the nut again to a torque of 170 ± 15 N·m (125 ± 11 lb ft).
End By: Install the air compressor. Refer to Disassembly and Assembly, "Air Compressor -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:34:10 UTC+0800 2020
2/2(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01897971
Hydraulic System Pressure - Release - Forest Machines
SMCS - 3000-553; 4250-553; 4300-553; 5050-553
S/N - B1K1-UP
S/N - B2L1-UP
S/N - B3M1-UP
S/N - B4N1-UP
Pressure Release Procedure
The release of hydraulic pressure in a hydraulic circuit is required before service is performed to
that hydraulic circuit. Release the pressure in the following hydraulic circuits before any hydraulic
lines are disconnected or removed from that hydraulic circuit.
• Boom hydraulic circuit
• Stick hydraulic circuit
• Heel hydraulic circuit
• Grapple hydraulic circuit
• Swing hydraulic circuit
• Travel hydraulic circuit
• Attachment hydraulic circuits (if equipped)
• Pilot hydraulic circuit
• Return hydraulic circuit
1/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Note: Refer to the Disassembly and Assembly Manual for additional information concerning
service of the components of specific hydraulic circuits.
Release Of Hydraulic Pressure From A Single Hydraulic
Circuit
Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from a single hydraulic
circuit of the main hydraulic system.
1. Position the machine on level ground.
2/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that single hydraulic
circuit. This will also release any pressure that might be present in the pilot hydraulic
circuit.
Note: If the desired hydraulic circuit that requires service requires the activation of a switch
for operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Turn the engine start switch to the OFF position.
9. Slowly loosen the filler plug on the hydraulic tank and release the pressure from the
hydraulic tank. Leave the filler plug loose for a minimum of 45 seconds. This will release
the pressure that may be present in the return hydraulic circuit.
10. Tighten the filler plug on the hydraulic tank to the specified torque.
11. The pressure in the single hydraulic circuit that requires service is now released and lines
and components can be disconnected or removed from that hydraulic circuit.
Release Of Hydraulic Pressure From Multiple Hydraulic
Circuits
3/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Perform the following Steps in order to release the hydraulic pressure from multiple hydraulic
circuits of the main hydraulic system.
1. Position the machine on level ground.
4/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Illustration 2 g00733088
2. Position the stick at the full STICK OUT position. Fully retract the heel cylinder. Position
the grapple against the heel and close the grapple. Lower the boom until the grapple is flat
on the ground. Refer to Illustration 1.
3. Shut off the engine.
4. Turn the engine start switch to the ON position without starting the engine.
5. Place the hydraulic activation control lever in the UNLOCKED position.
6. Move only the joysticks or the pedals of the hydraulic circuit that requires service to the
FULL STROKE positions. This will release the high pressure only in that hydraulic circuit.
This will also release any pressure that might be present in the pilot hydraulic circuit.
Note: If the hydraulic circuit that requires service requires the activation of a switch for
operation, activate the necessary switches for the operation of the hydraulic circuit.
7. Place the hydraulic activation control lever in the LOCKED position.
8. Start the engine.
9. Place the hydraulic activation control lever in the UNLOCKED position. Do not move any
joysticks or pedals from the NEUTRAL position during this step. Do not activate any
switches during this Step.
10. Return the hydraulic activation control lever to the LOCKED position.
11. Shut off the engine.
12. Repeat Steps 4 through 11 for each additional hydraulic circuit that requires service.
13. After releasing the hydraulic pressure in each of the desired hydraulic circuits, place the
hydraulic activation control lever in the LOCKED position.
5/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. 14. Turn the engine start switch to the OFF position.
15. Slowly loosen the filler plug on the hydraulic tank and release the pressure. Leave the filler
plug loose for a minimum of 45 seconds. This will release the pressure that may be present
in the return hydraulic circuit.
16. Tighten the filler plug on the hydraulic tank to the specified torque.
17. The pressure in the multiple hydraulic circuits that require service is now released and lines
and components can be disconnected or removed from those hydraulic circuits.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:35:33 UTC+0800 2020
6/6(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01694093
Battery - Remove and Install
SMCS - 1401-010
Removal Procedure
Note: This machine contains four batteries. The batteries are connected in series. Mark the
position of both the batteries and the battery cables prior to removal.
1. Open the rear access door on the left side of the machine.
Illustration 1 g00872239
2. Move the battery disconnect switch (1) to the OFF position.
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 2 g00872229
3. Remove nuts (2) from battery covers (3) .
4. Remove battery covers (3) .
Illustration 3 g00872255
5. Move rubber covers (4) from the battery terminal posts.
6. Remove the negative terminals from each of the batteries.
7. Remove the positive terminals from each of the batteries.
8. Remove the batteries.
Installation Procedure
Note: This machine contains four batteries. The batteries are connected in series. Each battery
MUST be in the correct position in order for correct machine operation.
1. Install the batteries in the correct position.
2. Install the positive terminals on each of the batteries.
3. Install the negative terminals on each of the batteries.
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. Illustration 6 g00872239
7. Move the battery disconnect switch (1) to the ON position.
8. Close the access door.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:36:28 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692348
Alternator - Remove and Install
SMCS - 1405-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7113 Reverse Ratchet 1
1. Open the hood.
2. Disconnect the positive battery terminal. This will prevent any damage to the wiring or to
the alternator.
Illustration 1 g00871311
3. Disconnect wiring terminals (1), (2), and (3) from the alternator.
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00871323
4. Insert Tooling (A) in slot (4). Apply downward pressure in order to remove the belt.
Illustration 3 g00871363
5. Remove bolt (5) from the belt guard.
2/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Illustration 4 g00871375
6. Remove nut (6) and remove the bolt. Remove the guard.
Illustration 5 g00871388
7. Remove spacer (7) and bolt (8) .
8. Remove alternator (9) .
Installation Procedure
1. Place alternator (9) in position.
Illustration 6 g00871388
2. Install spacer (7) and bolt (8). Remove the alternator.
3/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. Illustration 7 g00871375
3. Position the guard and install nut (6) .
Illustration 8 g00871363
4. Install bolt (5) in the belt guard.
Illustration 9 g00871323
5. Insert Tooling (A) in slot (4). Apply downward pressure in order to install the belt.
4/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. Illustration 10 g00871311
6. Connect wiring terminals (1), (2), and (3) to the alternator.
7. Connect the positive battery terminal.
8. Close the hood.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:37:24 UTC+0800 2020
5/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692671
Electric Starting Motor - Remove and Install
SMCS - 1453-010
Removal Procedure
1. Disconnect the battery cables.
Illustration 1 g00871495
1/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 2 g00871498
2. Place an index mark on all of the electrical wires that are connected to the electric starting
motor. Disconnect the electrical wires from the electric starting motor.
Illustration 3 g00871501
3. Remove top starter bolt (1) .
Illustration 4 g00871506
2/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. 4. Remove bottom starter bolts (2) and use a hoist and a lifting sling to remove starter (3). The
weight of the starter is approximately 32 kg (70 lb).
Installation Procedure
1. Inspect the condition of the gasket. Replace the gasket, if necessary.
2. Install the gasket on the electric starting motor.
Illustration 5 g00871506
3. Use a hoist and a lifting sling to position starter (3) and install bottom starter bolts (2). The
weight of the starter is approximately 32 kg (70 lb).
Illustration 6 g00871501
4. Install top starter bolt (1) .
3/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 7 g00871495
Illustration 8 g00871498
5. Connect all of the electrical wires to the electric starting motor by using the index marks.
6. Connect the battery cables.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 10 08:38:20 UTC+0800 2020
4/4(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C FM EXCAVATOR B3M
Configuration: 330C Forest Swing Machine B3M00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Engine Supplement
Media Number -RENR5439-02 Publication Date -01/08/2003 Date Updated -21/08/2003
i01692852
Fuel Filter (Primary) and Fuel Filter Base - Remove and
Install
SMCS - 1261-010; 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 2P-8250 Strap Wrench As 1
B
6V-9508 Face Seal Plug (11/16 inch by 16 THD) 2
6V-9829 Cap Assembly (11/16 inch by16 THD) 2
Fuel leaked or spilled onto hot surfaces or electrical components can
cause a fire. To help prevent possible injury, turn the start switch off
when changing fuel filters or water separator elements. Clean up fuel
spills immediately.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
1/5(W)
w
2020/9/10
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...