Caterpillar Cat 330C Excavator (Prefix JNK) Service Repair Manual (JNK00001 and up).pdf

Service Repair Manual
Models
330C and 330C L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 330C EXCAVATOR JNK
Configuration: 330C & 330C L Excavators JNK00001-UP (MACHINE) POWERED BY C-9 Engine
Disassembly and Assembly
330C Excavator Machine Systems
Media Number -RENR5438-14 Publication Date -01/04/2010 Date Updated -13/04/2010
i02344155
Piston Motor (Hydraulic Fan) - Assemble
SMCS - 1386-016-QP; 5058-016-FM; 5058-016-HFN
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-9152 Bearing Puller Gp 1
C 1P-1857 Retaining Ring Pliers 1
D 1P-0510 Driver Gp 1
E 1U-6396 O-Ring Assembly Compound 1
F 1P-1854 Retaining Ring Pliers 1
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have the
same sealing properties as a new O-ring. A reconditioning procedure should not be degraded
because of a low cost component such as an O-ring or a gasket. Use Tooling (E) during the
assembly procedure.
Note: Cleanliness is an important factor. Before assembly, all parts should be thoroughly cleaned
in cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry parts.
Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If any parts are
worn or damaged, use new parts for replacement. All disassembly and all assembly procedures
must be performed on a clean work surface and in a clean hydraulic area. Keep cleaned parts
covered and protected at all times.
Note: Apply a light film of SAE 10W oil to all components before assembly.
1/11(W)
w
2020/9/17
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...

Illustration 1 g00882512
1. Use Tooling (D) in order to install bearing cup (27) .
Note: Bearing cup (27) must be fully seated. Bearing cup (27) must be properly seated in
order for the motor to assemble properly.
2. Rotate housing (3) . Use Tooling (D) in order to install seal (26) .
3. Use Tooling (C) in order to install retaining ring (25) .
2/11(W)
w
2020/9/17

4. Install shaft (2) and bearing cone (16) in a suitable press. Press bearing cone (16) onto shaft
(2) .
Note: Bearing cone (16) must be fully seated. Bearing cone (16) must be properly seated in
order for the motor to assemble properly.
5. Assemble the rotating group in the following manner:
a. Install pins (24) in the top of barrel assembly (19) .
3/11(W)
w
2020/9/17

b. Rotate barrel assembly (19) . Install washer (23) and spring (22) . Place retaining ring
(21) on top of spring (22) .
Note: Do not attempt to install retaining ring (21) .
c. Rotate the barrel assembly. Retain the contents of the barrel. Position guide (20) on
pins (24) .
d. Install shaft (2) and the bearing through the barrel assembly.
Note: The shaft will align the barrel assembly.
4/11(W)
w
2020/9/17

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
e. Install Tooling (A) and barrel assembly (19) into a suitable press.
f. Compress the spring. Use Tooling (F) in order to install retaining ring (21) .
g. Slowly release the pressure on barrel assembly (19) .
h. Remove the shaft from barrel assembly (19) .
6. Install pistons and plate (18) into barrel assembly (19) .
7. Install swashplate (17) onto rotating group (14) .
5/11(W)
w
2020/9/17

Note: Barrel assembly (19) is rotating group (14) upon the installation of the pistons.
Note: Place identifying marks on swashplate (17) in order to locate two holes on the top of
the swashplate.
8. Install shaft (2) into rotating group (14) .
Note: Splines in shaft (2) must engage splines in rotating group (14) .
6/11(W)
w
2020/9/17

9. Align swashplate (17) with housing (3) .
Note: The holes on the top of swashplate (17) must engage the dowels in housing (3) .
10. Install rotating group (14) into housing (3) .
7/11(W)
w
2020/9/17

11. Raise the temperature of sleeve (15) . Install sleeve (15) onto shaft (2) .
12. Install shim (13) onto shaft (2) .
13. Install bearing cone (12) onto shaft (2) .
Note: Bearing cone (12) is a slip fit.
8/11(W)
w
2020/9/17

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
14. Install valve assembly (9) , sleeve (10) , and plug (11) into cover (5) .
15. Use Tooling (A) to install bearing cup (8) into cover (5) .
9/11(W)
w
2020/9/17

16. Install port plate (6) onto cover (5) .
Note: Take note of the slot in the reverse side of port plate (6) . The slot will receive the
dowel in cover (5) .
17. Install O-ring seal (7) on cover (5) .
10/11(W)
w
2020/9/17

18. Install cover (5) onto housing (3) .
19. Secure cover (5) with bolts (4) .
20. Install key (1) into shaft (2) .
End By: Install the piston motor. Refer to Disassembly and Assembly, "Piston Motor (Hydraulic
Fan) - Install ".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:43:50 UTC+0800 2020
11/11(W)
w
2020/9/17

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02344156
Piston Motor (Hydraulic Fan) - Install
SMCS - 1386-012-QP; 5058-012-FM
Installation Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6(W)
w
2020/9/17

1. Position piston motor (23) into the bracket. Secure the piston motor with bolts (22) .
2. Install adapter (21) onto the piston motor.
3. Install nut (20) , fan blade (19) , and bolts (18) .
2/6(W)
w
2020/9/17

4. Attach a suitable lifting device to the piston motor and fan assembly (17) . The weight of the
piston motor and fan assembly (17) is approximately 29 kg (65 lb). Position the piston
motor and fan assembly (17) . Install bolts (16) .
5. Install hose assemblies (15) .
3/6(W)
w
2020/9/17

6. Install upper fan guard (14) and bolts (13) .
7. Install tube assemblies (10) and (9) . Install bolts (12) and (11) .
8. Slide the hoses from tube assemblies (10) and (9) into position. Install hose clamps (8) .
4/6(W)
w
2020/9/17

9. Install strap (7) and bolts (6) .
10. Install brace (5) and bolts (4) .
11. Install plates (1) , (2) , and (3) . Install the bolts.
5/6(W)
w
2020/9/17

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04776349
Gear Pump (Fan Drive) - Remove
SMCS - 1387-011-GT; 5073-011-HFN
Removal Procedure
Start By:
a. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the oil from the hydraulic oil tank into a suitable container for storage or disposal.
The capacity of the hydraulic oil tank is 175 L (46 US gal).
1/2(W)
w
2020/9/17

2. Remove hose assemblies (2) and (3).
3. Remove nuts (1). Remove gear pump (4).
4. Remove nut (5). Remove gear (6), gasket (8), flange (9), key (10), and the O-ring seal.
5. Use a suitable press to remove bearing (7) from gear (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Sep 17 13:45:42 UTC+0800 2020
2/2(W)
w
2020/9/17

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i04959810
Gear Pump (Fan Drive) - Install
SMCS - 1387-012-GT; 5073-012-HFN; 5073
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover
any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
1/3(W)
w
2020/9/17

1. Use a suitable press to Install bearing (7) onto gear (6).
2. Install key (10). Install the O-ring seal onto flange (9). Install flange (9), gasket (8). Install
gear (6) and nut (5).
Note: Do not tighten nut at this time. The gear pump must be installed on the engine before
the nut is tightened. This procedure will prevent the pump from being damaged internally.
3. Position gear pump (4).
4. Secure gear pump (4) into position with bolts and nuts (1).
5. Remove the front access cover (not shown) in order to tighten nut (5). Tighten nut (5) to a
torque of 80 ± 8 N·m (59 ± 6 lb ft).
6. Install the front access cover.
7. Connect hose assemblies (2) and (3).
2/3(W)
w
2020/9/17

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i01796054
Handle (Joystick) - Remove and Install
SMCS - 5705-010
Removal Procedure
1. Remove the cover from the front of the console. Remove screws (1) .
1/6(W)
w
2020/9/17

2. Remove screws (2) from the rear of the console.
3. Open armrest (3). Remove screws (4). Remove armrest (3) .
2/6(W)
w
2020/9/17

4. Reposition cover (6) in order to access the harness assembly on the right hand console.
Disconnect harness assembly (5) .
5. Remove cover (6) from the console.
6. Disconnect harness assembly (7) from the joystick.
7. Lift rubber boot (8) over handle (9) .
Note: Mark the location of locknut (10) and the handle for installation procedures.
8. Hold nut (11). Loosen locknut (10). Unscrew handle (9) in order to remove the handle.
9. Remove rubber boot (8) from the handle.
3/6(W)
w
2020/9/17

Caterpillar Cat 330C Excavator (Prefix JNK) Service Repair Manual (JNK00001 and up).pdf

Recommended

Recommended

More Related Content

More from dujkdksmdmdm

More from dujkdksmdmdm (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 330C Excavator (Prefix JNK) Service Repair Manual (JNK00001 and up).pdf