The document provides assembly instructions for a travel motor in 28 steps. It includes illustrations and lists required tools. Key steps include installing seals and bearings, assembling piston and swashplate components, installing plates and discs, and fitting the head assembly using lifting tools due to component weights of 21-43 kg. The travel motor is then ready for installation on the excavator.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
This document provides instructions for removing and installing various engine components on a Caterpillar 336 Excavator. It details procedures for removing and installing the lifters, camshaft, camshaft gear, camshaft bearings, and engine oil pan. The document includes lists of required tools and multiple illustrations to support the step-by-step instructions provided.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
The document provides instructions for removing and installing components on a 336 excavator, including the piston motor (hydraulic fan), hydraulic lockout control, and operator monitor. It contains detailed procedures with required tools and multiple illustrations showing each step. Safety warnings are included to prevent injury when working with spring-loaded parts. The document is from Caterpillar and intended for technicians servicing 336 excavator models powered by a C9.3 engine.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...cdsaas
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 336 e l excavator (prefix gtj) service repair manual (gtj0000...fjskekmdm
The document provides instructions for assembling a travel motor used in excavators. It describes 27 steps to assemble components like seals, springs, pistons, and plates into the motor housing. Key steps include lubricating mating surfaces, installing retaining rings, and tightening bolts to specified torques. The assembly ends by installing the motor housing cover and bolts, and noting the motor is then ready for installation in the excavator.
This document provides instructions for removing and installing various engine components on a Caterpillar 336 Excavator. It details procedures for removing and installing the lifters, camshaft, camshaft gear, camshaft bearings, and engine oil pan. The document includes lists of required tools and multiple illustrations to support the step-by-step instructions provided.
Caterpillar cat 323 f excavator (prefix kby) service repair manual (kby00001 ...jfdskekdmme
This document provides instructions for removing and installing the rear power take-off (RPTO) on a Caterpillar 323F excavator engine. The removal procedure involves removing 12 components including gears, adapters, and sleeve bearings. The installation procedure describes installing these components in reverse order and ensuring proper alignment and torque specifications are followed.
The document provides instructions for removing and installing components on a 336 excavator, including the piston motor (hydraulic fan), hydraulic lockout control, and operator monitor. It contains detailed procedures with required tools and multiple illustrations showing each step. Safety warnings are included to prevent injury when working with spring-loaded parts. The document is from Caterpillar and intended for technicians servicing 336 excavator models powered by a C9.3 engine.
Caterpillar cat 390 f excavator (prefix hng) service repair manual (hng00001 ...fjskefksemer
This document provides instructions for removing and installing the front gear group of a C18 engine. The removal procedure involves removing 14 bolts, plates, gears and seals. Special care must be taken to mark gear orientations and not turn the crankshaft during removal. The installation procedure describes cleaning components, applying thread lock compound, installing 14 gears, plates and seals in the correct order and orientation, and adjusting backlash between gears. Proper removal and installation is important to avoid engine damage.
Caterpillar cat 345 d l excavator (prefix yee) service repair manual (yee0000...hhfjksekmm
This document provides instructions for removing and installing various components of the rear gear group and crankshaft rear seal of a 345D L Excavator with a C13 engine. The removal procedure includes using various tools to remove bolts, seals, gears, bushings, and bearings. The installation procedure provides instructions on cleaning, inspecting, applying threadlock, and installing components while ensuring proper dimensions and alignments are met. Torque specifications and notes are provided throughout.
Caterpillar cat 349 d l excavator (prefix fla) service repair manual (fla0000...cdsaas
1. The document provides installation and removal instructions for various components of a C13 engine, including the flywheel, rear gear group, crankshaft rear seal, and more.
2. Detailed steps and illustrations are given for each procedure, including the necessary tools. Precautions are outlined, such as containing fluids and keeping parts clean.
3. Specifications and additional reference documents are cited to ensure proper installation and inspection of components like the crankshaft seal surface and wear sleeves.
Caterpillar cat 320 d lrr excavator (prefix eby) service repair manual (eby00...fjkskedmme
This document provides instructions for removing and installing various components of an excavator engine, including:
1. Removing and installing the flywheel housing, which requires using lifting straps and removing bolts.
2. Removing and installing the crankshaft pulley, which requires using a puller and tightening a nut.
3. Removing the crankshaft front seal using a slide hammer puller and installing a new seal with an installer tool.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsefkskemmm
This document provides instructions for disassembling and assembling the front drive and steering axle of a Caterpillar 424D backhoe loader. The disassembly process involves removing components like the carrier gear, hub, seals, bearings and kingpins. The assembly process describes installing these components in reverse order and adjusting shims to achieve the correct rolling resistance. Required tools are listed.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar Cat 326F L and 326F LN Excavator (Prefix HCJ) Service Repair Manu...yan77xunhao
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The housing is positioned onto an assembly stand using lifting equipment. External components like the head assembly and relief valves are attached last. The assembly ensures proper installation of all sealed, sprung, and rotating components in the correct orientation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f l excavator (prefix hcj) service repair manual (hcj0000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting equipment, completing the assembly of the travel motor.
Caterpillar Cat 326F L Excavator (Prefix HCJ) Service Repair Manual (HCJ00001...f8usiejdkmdd
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The housing is positioned onto an assembly stand using lifting equipment. External components like the head assembly and relief valves are attached last. The assembly ensures proper installation of all sealed, sprung, and rotating components in the correct orientation.
Caterpillar cat 326 f l excavator (prefix hcj) service repair manual (hcj0000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...kmf9ioseodk
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar Cat 326F L Excavator (Prefix HCJ) Service Repair Manual (HCJ00001...dujdkksdmm
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before securing the head assembly to the housing with bolts. Finally, relief valves and spools are installed to complete the assembly.
Caterpillar cat 326 f ln excavator (prefix hca) service repair manual (hca000...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f l excavator (prefix hca) service repair manual (hca0000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f excavator (prefix hca) service repair manual (hca00001 ...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Install the rotating group and brake assembly into the motor housing.
3. Attach the motor head assembly to the housing and install remaining components like seals and springs.
The instructions include 28 steps and require various tools to correctly assemble the travel motor.
Caterpillar cat 326 f ln excavator (prefix hca) service repair manual (hca000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 330 c l excavator (prefix jnk) service repair manual (jnk0000...hhjsekmdmm
The document provides installation instructions for a gear pump used in the fan drive of an excavator. It outlines 20 steps to assemble the piston motor that drives the hydraulic fan. These include pressing bearings onto shafts, installing springs, O-rings, seals, and housing components in the proper order and orientation. Precautions are given to ensure cleanliness and prevent injury from parts under pressure.
Caterpillar cat 336 f l excavator (prefix ljy) service repair manual (ljy0000...fjkskedmme
1. The document provides step-by-step instructions for disassembling and assembling the diesel exhaust fluid module of Caterpillar 336F excavators.
2. The disassembly procedure involves draining the fluid, removing hoses and connectors, and taking apart the various module components like the pump, tank, and control electronics.
3. The assembly procedure lists the parts and tools needed and describes reinstalling the components in reverse order and ensuring proper tightening of connections.
Caterpillar cat 349 d2 l excavator (prefix yae) service repair manual (yae000...cdsaas
The document provides instructions for assembling and installing a travel motor. It outlines 33 steps for assembling components like pistons, seals, plates, and bearings. Measurement checks are specified to ensure proper assembly. Tools required are listed. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 330 d excavator (prefix edx) service repair manual (edx00001 ...hhjsekmdmm
The document provides instructions for assembling the swing drive of an excavator. It describes 30 steps for installing bearings, gears, seals, and other components into the swing drive housing. Tools required include pliers, link brackets, a torque wrench, and sealant. Proper cleaning and lubrication of parts is emphasized. Weights of components are provided to note the number of people needed for installation.
Caterpillar cat 319 d l excavator (prefix rjp) service repair manual (rjp0000...fjkskedmme
The document provides instructions for disassembling and assembling a final drive on a 319D L and 319D LN excavator. The disassembly procedure involves removing 33 individual parts from the final drive including the cover, carrier assembly, ring gears, and main housing. The assembly procedure instructs installing 31 of the parts back into the final drive in reverse order and provides details on properly preloading the bearings and determining the correct shim thickness.
Caterpillar cat d8 n track type tractor dozer bulldozer (prefix 1xj) service ...ufjjdjffjkskemm
This document provides instructions for removing and installing the rear gear group and crankshaft rear seal on a Caterpillar D8N track-type tractor with a 3406 engine. The removal procedure involves using various tools to remove 14 bolts and components including gears, covers, seals, and bearings. The installation procedure provides instructions to install these same components in reverse order and includes notes about cleaning, applying sealant, and ensuring proper dimensions and alignment. Proper tools and torque specifications are listed for each step.
Caterpillar cat 424 d backhoe loader (prefix bgp) service repair manual (bgp0...fjjsefkskemmm
This document provides instructions for disassembling and assembling the front drive and steering axle of a Caterpillar 424D backhoe loader. The disassembly process involves removing components like the carrier gear, hub, seals, bearings and kingpins. The assembly process describes installing these components in reverse order and adjusting shims to achieve the correct rolling resistance. Required tools are listed.
Caterpillar cat 336 d l excavator (prefix ppn) service repair manual (ppn0000...fjskekdmjekm
The document provides instructions for disassembling and assembling a piston pump (hydraulic fan) for a 336D L & 336D LN excavator. The disassembly procedure involves 30 steps that remove components like the head, port plate, bearing cups, pistons, pins, and springs. The assembly procedure involves 25 steps that install components in the reverse order, and notes that cleanliness is important during assembly. Tools required include retaining ring pliers, a dial indicator, and a bearing puller.
Caterpillar Cat 326F L and 326F LN Excavator (Prefix HCJ) Service Repair Manu...yan77xunhao
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The housing is positioned onto an assembly stand using lifting equipment. External components like the head assembly and relief valves are attached last. The assembly ensures proper installation of all sealed, sprung, and rotating components in the correct orientation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f l excavator (prefix hcj) service repair manual (hcj0000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting equipment, completing the assembly of the travel motor.
Caterpillar Cat 326F L Excavator (Prefix HCJ) Service Repair Manual (HCJ00001...f8usiejdkmdd
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The housing is positioned onto an assembly stand using lifting equipment. External components like the head assembly and relief valves are attached last. The assembly ensures proper installation of all sealed, sprung, and rotating components in the correct orientation.
Caterpillar cat 326 f l excavator (prefix hcj) service repair manual (hcj0000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
Caterpillar cat 326 f ln excavator (prefix hcj) service repair manual (hcj000...kmf9ioseodk
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before installing the head assembly. Bolts are tightened to the specified torques to complete the assembly. The travel motor is then ready for installation.
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, bearings, springs, and plates in the correct order and orientation.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar Cat 326F L Excavator (Prefix HCJ) Service Repair Manual (HCJ00001...dujdkksdmm
The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto the brake piston before installing it. Additional seals and springs are fitted before securing the head assembly to the housing with bolts. Finally, relief valves and spools are installed to complete the assembly.
Caterpillar cat 326 f ln excavator (prefix hca) service repair manual (hca000...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f l excavator (prefix hca) service repair manual (hca0000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f excavator (prefix hca) service repair manual (hca00001 ...kmf9ioseodk
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Install the rotating group and brake assembly into the motor housing.
3. Attach the motor head assembly to the housing and install remaining components like seals and springs.
The instructions include 28 steps and require various tools to correctly assemble the travel motor.
Caterpillar cat 326 f ln excavator (prefix hca) service repair manual (hca000...fujsekfkksemm
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar Cat 326F, 326F L and 326F LN Excavator (Prefix HCA) Service Repai...yan77xunhao
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, pistons, springs, and plates.
2. Position the motor housing onto an assembly stand and install additional components like the brake piston.
3. Attach the head assembly onto the housing using lifting tools, completing the travel motor assembly.
Caterpillar cat 326 f l excavator (prefix hca) service repair manual (hca0000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 3 steps:
1. Install various internal components of the travel motor like seals, springs, pistons, and plates in the proper order and orientation.
2. Position the housing and install additional components like the rotating group, brake piston, and head assembly using lifting tools due to the heavy weight of parts.
3. Tighten bolts and install remaining parts like relief valves and spools to complete the assembly.
Caterpillar cat 326 f ln excavator (prefix hca) service repair manual (hca000...fjsekdmmeed
The document provides assembly instructions for a travel motor in 28 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto brake components before installing them. Finally, the head assembly is attached to the housing and bolts are tightened to specified torques to complete the assembly.
Caterpillar cat 326 f excavator (prefix hca) service repair manual (hca00001 ...fjsekdmmeed
The document provides assembly instructions for a travel motor in 28 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating assembly and brake components are assembled separately and placed into the housing. Finally, the head assembly is attached to the housing and relief valves and spools are installed to complete the travel motor assembly.
Caterpillar cat 326 f excavator (prefix hca) service repair manual (hca00001 ...fujsekfkksemm
The document provides assembly instructions for a travel motor in 28 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating group is placed into the housing along with plates and discs. Seals are fitted onto brake components before installing them. Finally, the head assembly is attached to the housing and bolted in place, completing the assembly.
Caterpillar Cat 326F L Excavator (Prefix HCA) Service Repair Manual (HCA00001...dujdkksdmm
The document provides assembly instructions for a travel motor in 28 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The rotating assembly and brake components are assembled separately and placed into the housing. Finally, the head assembly is attached to the housing and relief valves and spools are installed to complete the travel motor assembly.
Similar to Caterpillar cat 326 f excavator (prefix fbr) service repair manual (fbr00001 and up) (20)
Caterpillar cat 345 c l excavator (prefix wde) service repair manual (wde0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 345 c l excavator (prefix spc) service repair manual (spc0000...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group. It then details removing components from the rotating group like the shaft assembly, bearings, and piston assemblies. The assembly section provides steps to reinstall these components in reverse order and includes precautions like cleaning, applying lubricant, and ensuring proper orientation of parts.
Caterpillar cat 345 c l excavator (prefix scn) service repair manual (scn0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly process involves removing over 20 individual parts from the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly section outlines installing new seals, pressing in bearing cups, adjusting shims to set proper bearing preload, and reinstalling all parts in reverse order. Precise positioning of stamped identification marks on gears is required for correct reassembly.
Caterpillar cat 345 c l excavator (prefix s5m) service repair manual (s5m0000...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C L excavator. The disassembly procedure involves removing over 20 components of the final drive including the cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure instructs to clean all parts, apply anti-seize compound, install bearing cups and cones, and adjust the bearing preload using shims to achieve the proper load. Precise positioning of identification marks is required to reinstall parts in their original locations.
Caterpillar cat 345 c hydraulic excavator (prefix tdg) service repair manual ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, pistons, and housing pieces. It then lists 13 steps for assembly, replacing components in reverse order and noting to clean all parts, apply lubricant, and measure clearances during assembly to ensure proper operation. Tools required are listed for both disassembly and assembly.
Caterpillar cat 345 c excavator (prefix wde) service repair manual (wde00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of a 345C excavator. The disassembly procedure involves removing 28 parts in 28 steps, including removing the final drive cover, ring gear, carrier assemblies, planetary gears, and sprocket housing. The assembly procedure involves installing 29 parts in 29 steps in the reverse order, adjusting bearing preload using shims, and applying anti-seize compound and thread lock to ensure proper assembly. Tools such as retaining ring pliers, eyebolts, and a transmission stand are required.
Caterpillar cat 345 c excavator (prefix spc) service repair manual (spc00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with disassembly steps including removing the head, pins, plates, seals, brake piston, separator plates, disks, and rotating group components. Assembly steps are then listed in reverse order and include installing seals, spacers, piston assemblies, springs and other components back into the travel motor housing. Precautions are given such as cleaning parts and applying lubricant before assembly.
Caterpillar cat 345 c excavator (prefix dhp) service repair manual (dhp00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling a travel motor. It begins with removing external components like the displacement change valve and head. Internal components like the brake piston, disks, and rotating group are then removed. Individual parts in the rotating group like the piston assemblies and barrel are also taken apart. Precise identification and reinstallation of parts is emphasized. The assembly section provides instructions for reinstalling components in reverse order and ensuring proper placement and torque of parts.
Caterpillar cat 345 b series ii excavator (prefix dcw) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176 engine. The removal procedure involves disconnecting sensors, tubes, wiring harnesses, and fuel filters before removing bolts and lifting off the cylinder head. The installation procedure specifies cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all components in reverse order. Tools required include wrenches, taps, and a strap wrench.
Caterpillar cat 345 b series ii excavator (prefix ccc) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing the cylinder head on a 345B Series II Excavator with a 3176C engine. The removal process involves disconnecting various sensors and tubes, removing bolts, and lifting the cylinder head off. The installation involves cleaning surfaces, installing new gaskets and seals, lifting the cylinder head into place, and torquing the head bolts to the specified sequence and values. Proper cleaning, lubrication, and torque procedures are emphasized to ensure correct installation.
Caterpillar cat 345 b series ii excavator (prefix ald) service repair manual ...fjsekdmmeed
This document provides instructions for removing and installing a lifter group on a 3176C engine. The removal process involves taking out bolts and separating the lifter assembly into sections to remove individual components like brackets, lifters and injector lifters. The installation is the reverse of removal, requiring cleaning of parts and reinstallation in the proper order and orientation. Precautions are provided to contain fluids and dispose of them according to regulations.
Caterpillar cat 345 b l excavator (prefix 9cw) service repair manual (9cw0000...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a Caterpillar 345B L excavator engine. It details removing components like the valve mechanism cover, rocker shaft, and pushrods. It then explains how to remove the cylinder head by disconnecting sensors and tubes, and removing bolts. Reinstallation involves cleaning surfaces, installing new gaskets and seals, tightening bolts in a specific sequence, and reconnecting all removed components and hoses. Tools required are also listed.
Caterpillar cat 345 b l excavator (prefix 8rw) service repair manual (8rw0000...fjsekdmmeed
The document provides instructions for removing and installing a cylinder head and lifter group on a Caterpillar 345B L EXCAVATOR engine. It describes disconnecting various engine components and sensors, removing bolts and gaskets, and lifting the cylinder head off the engine block. It then details cleaning surfaces, installing new gaskets and seals, bolting the head back onto the block, and reconnecting all components in reverse order. Proper torque specifications are provided for all fasteners.
Caterpillar cat 345 b excavator (prefix ayr) service repair manual (ayr00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the final drive of an excavator model 345B. It describes removing components such as the travel motor, final drive, ring gear, and carrier assemblies. Detailed steps are provided to disassemble each assembly into individual parts. The assembly section instructs cleaning and inspecting parts, applying anti-seize compound, and installing components in reverse order using lifting tools and following markings made during disassembly. Proper bearing preload is set by measuring clearance with shims.
Caterpillar cat 345 b excavator (prefix amn) service repair manual (amn00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists 31 steps to disassemble parts like the head, plates, seals, pistons, and housing. It then lists 27 steps to reassemble these parts in reverse order, making sure to clean parts and apply lubricant. Proper installation of seals, washers, and keys is emphasized.
Caterpillar cat 345 b excavator (prefix amj) service repair manual (amj00001 ...fjsekdmmeed
This document provides assembly instructions for installing a travel motor on a 345B Excavator. It outlines 33 steps to assemble parts like seals, pistons, plates, and shafts inside the travel motor housing. It then describes 4 steps to install the assembled travel motor onto the final drive, including cleaning surfaces, replacing an O-ring seal, and using lifting tools to maneuver the motor into position. Proper torque specifications are given for tightening fasteners.
Caterpillar cat 345 b excavator (prefix amd) service repair manual (amd00001 ...fjsekdmmeed
This document provides assembly instructions for a travel motor on a 345B Excavator. It outlines 33 steps to assemble internal components like pistons, seals, plates and housing pieces. Measurement checks are included to ensure correct assembly. The instructions also cover installing the assembled travel motor by cleaning mating surfaces, replacing an O-ring seal, and using lifting tools to slide the motor into position in the final drive housing.
Caterpillar cat 345 b excavator (prefix 8kw) service repair manual (8kw00001 ...fjsekdmmeed
This document provides instructions for removing and installing a cylinder head on a 345B excavator engine. It includes 14 steps to remove the head, such as removing sensors, tubes, and bolts. The 20 step installation procedure describes cleaning surfaces, installing gaskets and seals, tightening bolts in a specific sequence, and reconnecting related components like sensors and tubes. Special tools are listed for tasks like removing the fuel filter. Cautions are provided about containing fluids and keeping parts clean to prevent damage and wear.
Caterpillar cat 345 b excavator (prefix 6mw) service repair manual (6mw00001 ...fjsekdmmeed
The document provides instructions for disassembling and assembling the travel motor of an excavator model 345B. It lists the required tools and parts. The disassembly instructions include removing components like the brake cover, brake assembly, springs, gears, and barrel assembly. The assembly instructions list installing components like bushings, bearings, seals and rings in reverse order of disassembly. Safety notices are provided to keep parts clean and prevent hydraulic system contamination.
Caterpillar cat 340 f excavator (prefix sgh) service repair manual (sgh00001 ...fjsekdmmeed
This document provides instructions for disassembling and assembling the swing drive of a 340F Excavator. The disassembly procedure involves removing 27 parts from the swing drive including the cover, sun gear, carrier assembly, planetary gears, ring gear, and pinion shaft. The assembly procedure instructs installing lip seals and bearings on the cage and pinion shaft and pressing the cage into the swing drive housing.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F EXCAVATOR FBR
Configuration: 326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05435999
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) in order to install
lip seal (28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g03431399
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g03431402
19. The notches in cam plate (20) must align with keys (26). The keys (26) are located in the
bottom of the housing of the travel motor.
Illustration 17 g00887355
7/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
8/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 11 09:17:39 UTC+0800 2020
10/10
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M00...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F EXCAVATOR FBR
Configuration: 326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i07505850
Travel Motor - Assemble
SMCS - 4351-016
S/N - B321-UP
S/N - EBK1-UP
S/N - ERL1-UP
S/N - FBR1-UP
S/N - GGJ1-UP
S/N - GHT1-UP
S/N - HBT1-UP
S/N - HCA1-UP
S/N - HCJ1-UP
S/N - HCK1-UP
S/N - JFR1-UP
S/N - JHF1-UP
S/N - KFA1-UP
S/N - LBN1-UP
S/N - LCG1-UP
S/N - MBX1-UP
1/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - RCN1-UP
S/N - TMR1-UP
S/N - TPG1-UP
S/N - WBA1-UP
S/N - WGL1-UP
S/N - XFK1-UP
S/N - YHA1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
Illustration 1 g06343795
1. Install lip seal (45) and bearing (44).
2. Install balls (46).
2/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g06343793
Illustration 3 g06343788
3. Install shaft (43) and springs (42).
4. Install pistons (41).
Illustration 4 g06343786
5. Install swashplate (40) into housing (26).
3/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g06343783
6. Install springs (39) and hold down ball (38) into barrel (37).
Illustration 6 g06343777
7. Install retainer (36) and piston (35) into barrel (37).
Illustration 7 g06343638
8. Install rotating group (34) into housing (26).
4/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g06343469
Illustration 9 g06343466
9. Install plates (33) and friction discs (32) in the orientation determined in the disassembly.
Illustration 10 g06343464
10. Install O-ring seal (31) into brake piston guide (30).
5/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 11 g06343462
11. Install brake piston guide (30).
Illustration 12 g06343437
12. Install O-ring seals (29) and back up rings (28) into brake piston (27).
Illustration 13 g06343877
13. Use Tooling (D) and a suitable lifting device to position housing (26) onto Tooling (A) and
(B). The weight of housing (26) is approximately 43 kg (95 lb).
14. Remove Tooling (D) and install brake piston (27).
6/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 14 g06343381
15. Install O-ring seals (25) and (24).
16. Install springs (23) and pins (22).
Illustration 15 g06343374
17. Install bearing (21) and control plate (20) into head assembly (18).
Illustration 16 g06343366
18. Use Tooling (C) and a suitable lifting device to install head assembly (18) onto the housing.
The weight of head assembly (18) is approximately 21 kg (47 lb).
7/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 17 g06343887
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
19. Install bolts (19). Tighten bolts (19) to a torque of 205 ± 10 N·m (151 ± 7 lb ft).
20. Install the bolts of Tooling (B)
Illustration 18 g06343315
8/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 19 g06343314
21. Install O-ring seal (17) onto relief valve (16).
22. Install relief valve (16) into the head assembly. Tighten relief valve (16) to a torque of
570 ± 20 N·m (420 ± 14 lb ft). Repeat for the opposite side.
Illustration 20 g06342009
23. Install spool (15).
Illustration 21 g06342005
9/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M0086...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
22. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install O-ring seal (12) onto plug (11).
25. Install ball (14), spring (13), and plug (11) into cap (6). Repeat for the opposite side.
Illustration 22 g06342000
Illustration 23 g06341942
Improper assembly of parts that are spring loaded can cause bodily
injury.
10/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M00...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
26. Install O-ring seal (10) onto cap (6).
27. Install washer (7), spring (8), guide (9), and cap (6) into the head assembly.
28. Repeat for the opposite side.
Illustration 24 g06341917
29. Install spool (4).
Illustration 25 g06341915
30. Install spring (3).
11/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M00...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 26 g06341912
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
31. Install plug (2A). Tighten plug (2A) to a torque of 54 ± 5 N·m (40 ± 4 lb ft). Repeat for the
opposite side.
Illustration 27 g06344110
32. Install plug (2) and the O-ring seal. Tighten plug (2) to a torque of 53 ± 2 N·m (39 ± 1 lb ft).
12/13
326F L Excavators FBR00001-UP (MACHINE) POWERED BY C7.1 Engine(M00...
2020/10/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...