The document provides assembly instructions for a travel motor in 27 steps. It begins by installing seals and bearings into the motor housing. Pistons, springs, and other internal components are then installed. The housing is positioned onto an assembly stand using lifting equipment. External components like the head assembly and relief valves are attached last. The assembly ensures proper installation of all sealed, sprung, and rotating components in the correct orientation.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F LN EXCAVATOR HCJ
Configuration: 326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05435999
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1U-7506 Adapter 1
8T-4244 Nut 6
8T-4223 Hard Washer 6
- M12 x 1.75 X 250 mm (10 inch) Threaded Rod 1
C 3E-3882 Eyebolt 1
D 1P-1859 Retaining Ring Pliers 1
E
1P-0510 Driver Gp 1
9S-9152 Bearing Puller Gp 1
F 1P-1861 Retaining Ring Pliers 1
G - Loctite 242 -
1/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00887762
1. Install O-ring seal (35) onto the housing of the travel motor.
Illustration 2 g00887754
2. Install seal (34) and piston actuator (33). Lubricate the surfaces of piston actuator (33) with
lubricant that is being sealed.
Illustration 3 g00887729
3. Install backup ring (32) and seal (31).
2/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00887619
4. Install cover (30) and bolts (29). Tighten bolts (29) to a torque of 28 ± 7 N·m (21 ± 5 lb ft).
Illustration 5 g00887589
5. Apply Tooling (G) to the mating surface of lip seal (28). Use Tooling (E) in order to install
lip seal (28). Lubricate the sealing lip of lip seal (28) with lubricant that is being sealed.
6. Use Tooling (F) in order to install retaining ring (27).
Illustration 6 g02107975
7. Rotate the housing.
3/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 8. Install keys (26) and locating pins (not shown) into the body of the travel motor.
9. Install bearing (25).
Illustration 7 g00887558
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
10. Install springs (24) into the barrel assembly. Install ball (23) onto springs (24). Lubricate
ball (23) with lubricant that is being sealed.
Illustration 8 g00887520
11. Lubricate the piston assemblies with lubricant that is being sealed. Install piston assemblies
and retainer plate (22) into barrel assembly (21).
4/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Take note of the mark on the piston assembly and the barrel assembly. The pistons
must be returned to the same position.
Illustration 9 g00887501
12. Lubricate cam plate (20) with lubricant that is being sealed. Install cam plate (20) onto
barrel assembly (21).
Illustration 10 g00888697
13. Install shaft (15) into a suitable press. Install bearing race (19) onto shaft (15).
Illustration 11 g00887426
5/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Rotate shaft (15) in the suitable press. Use Tooling (D) to install retaining ring (17) onto
shaft (15).
Illustration 12 g00888710
15. Install bearing race (18) onto shaft (15).
Note: Bearing race (18) must contact retaining ring (17).
Illustration 13 g00887405
16. Install Tooling (C) into shaft (15). Install shaft (15) into rotating assembly (16).
17. Place the pump housing into Tooling (A).
6/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g03431399
18. Use Tooling (C) in order to install rotating assembly (16) into the housing.
Illustration 15 g00887501
Illustration 16 g03431402
19. The notches in cam plate (20) must align with keys (26). The keys (26) are located in the
bottom of the housing of the travel motor.
Illustration 17 g00887355
7/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 20. Install plates (13) and friction discs (14) into the housing.
Note: Install the plates and the discs alternately.
Illustration 18 g00887336
21. Install backup ring (12) and seal (11) onto the brake piston.
22. Install backup ring (10) and seal (9) onto the brake piston.
Illustration 19 g00888967
23. Rotate brake piston (8).
24. Install brake piston (8) into the housing.
Note: Brake piston (8) must be level upon installation. The brake piston must be level in
order to prevent damage to the O-ring seals.
8/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 20 g00887311
25. Install springs (7) and O-ring seals (6).
Illustration 21 g00887302
26. Lubricate port plate (4) with lubricant that is being sealed. Install O-ring seal (3), port plate
(4), and bearing (5).
Illustration 22 g00887295
9/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
27. Install head (2) onto the body of the travel motor.
Note: During the installation of head (2) onto the travel motor, be careful not to damage the
mating surfaces of the components.
28. Install bolts (1). Tighten bolts (1) to a torque of 177 ± 18 N·m (131 ± 13 lb ft).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 25 15:03:32 UTC+0800 2020
10/10
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F LN EXCAVATOR HCJ
Configuration: 326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i07505850
Travel Motor - Assemble
SMCS - 4351-016
S/N - B321-UP
S/N - EBK1-UP
S/N - ERL1-UP
S/N - FBR1-UP
S/N - GGJ1-UP
S/N - GHT1-UP
S/N - HBT1-UP
S/N - HCA1-UP
S/N - HCJ1-UP
S/N - HCK1-UP
S/N - JFR1-UP
S/N - JHF1-UP
S/N - KFA1-UP
S/N - LBN1-UP
S/N - LCG1-UP
S/N - MBX1-UP
1/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. S/N - RCN1-UP
S/N - TMR1-UP
S/N - TPG1-UP
S/N - WBA1-UP
S/N - WGL1-UP
S/N - XFK1-UP
S/N - YHA1-UP
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1P-2420 Transmission Repair Stand 1
FT-0957 Positioning Gp 4
B
- M16x2 Threaded Rod 3
8T-1757 Nut 6
9X-8268 Washer 6
C 421-5662 Lifting Eye Assembly 1
D 421-5663 Lifting Eye Assembly 2
Illustration 1 g06343795
1. Install lip seal (45) and bearing (44).
2. Install balls (46).
2/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g06343783
6. Install springs (39) and hold down ball (38) into barrel (37).
Illustration 6 g06343777
7. Install retainer (36) and piston (35) into barrel (37).
Illustration 7 g06343638
8. Install rotating group (34) into housing (26).
4/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 8 g06343469
Illustration 9 g06343466
9. Install plates (33) and friction discs (32) in the orientation determined in the disassembly.
Illustration 10 g06343464
10. Install O-ring seal (31) into brake piston guide (30).
5/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 11 g06343462
11. Install brake piston guide (30).
Illustration 12 g06343437
12. Install O-ring seals (29) and back up rings (28) into brake piston (27).
Illustration 13 g06343877
13. Use Tooling (D) and a suitable lifting device to position housing (26) onto Tooling (A) and
(B). The weight of housing (26) is approximately 43 kg (95 lb).
14. Remove Tooling (D) and install brake piston (27).
6/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 14 g06343381
15. Install O-ring seals (25) and (24).
16. Install springs (23) and pins (22).
Illustration 15 g06343374
17. Install bearing (21) and control plate (20) into head assembly (18).
Illustration 16 g06343366
18. Use Tooling (C) and a suitable lifting device to install head assembly (18) onto the housing.
The weight of head assembly (18) is approximately 21 kg (47 lb).
7/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 17 g06343887
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
19. Install bolts (19). Tighten bolts (19) to a torque of 205 ± 10 N·m (151 ± 7 lb ft).
20. Install the bolts of Tooling (B)
Illustration 18 g06343315
8/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 19 g06343314
21. Install O-ring seal (17) onto relief valve (16).
22. Install relief valve (16) into the head assembly. Tighten relief valve (16) to a torque of
570 ± 20 N·m (420 ± 14 lb ft). Repeat for the opposite side.
Illustration 20 g06342009
23. Install spool (15).
Illustration 21 g06342005
9/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
24. Install O-ring seal (12) onto plug (11).
25. Install ball (14), spring (13), and plug (11) into cap (6). Repeat for the opposite side.
Illustration 22 g06342000
Illustration 23 g06341942
Improper assembly of parts that are spring loaded can cause bodily
injury.
10/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
26. Install O-ring seal (10) onto cap (6).
27. Install washer (7), spring (8), guide (9), and cap (6) into the head assembly.
28. Repeat for the opposite side.
Illustration 24 g06341917
29. Install spool (4).
Illustration 25 g06341915
30. Install spring (3).
11/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 26 g06341912
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
31. Install plug (2A). Tighten plug (2A) to a torque of 54 ± 5 N·m (40 ± 4 lb ft). Repeat for the
opposite side.
Illustration 27 g06344110
32. Install plug (2) and the O-ring seal. Tighten plug (2) to a torque of 53 ± 2 N·m (39 ± 1 lb ft).
12/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 28 g06341880
33. Install plugs (1) and the O-ring seals.
34. Remove the travel motor from Tooling (A) and (B). The weight of the travel motor is
approximately 70 kg (154 lb).
End By:
a. Install the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Oct 25 15:04:28 UTC+0800 2020
13/13
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 ...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 326F LN EXCAVATOR HCJ
Configuration: 326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 Engine
Disassembly and Assembly
326F, 329F and 330F Excavators Machine Systems
Media Number -UENR3313-07 Publication Date -01/09/2015 Date Updated -12/09/2018
i05435924
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
326F L & 326F LN Excavators HCJ00001-UP (MACHINE) POWERED BY C7.1 En...
2020/10/25
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...