The document provides step-by-step instructions for disassembling and assembling the travel motor of a 323D excavator. It details 27 steps for disassembly, removing components like the head, brake piston, barrel assembly, and shaft. It then outlines 24 steps for reassembly, replacing seals and installing components in the reverse order of removal to rebuild the travel motor. Special care is noted for aligning parts and preventing damage to surfaces.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 d l excavator (prefix wne) service repair manual (wne0000...fjskksmem
The document provides instructions for installing the crankshaft in a Caterpillar C6.4 engine:
1. Thrust washers and main bearings are installed in the cylinder block and bearing caps.
2. The crankshaft is positioned onto the main bearings using a lifting device.
3. Main bearing caps with bearings are installed and torqued to specifications.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
Caterpillar cat 323 d excavator (prefix zmf) service repair manual (zmf00001 ...fjskksmem
The document provides instructions for removing and installing various engine components on a Caterpillar 323D excavator. It describes in detail how to remove and install the crankshaft pulley, crankshaft front seal, and idler gear of the front gear group. The procedures involve using various tools to remove fasteners and other parts, taking care to keep components clean and ensure proper alignment of gears.
Caterpillar cat 320 d lrr excavator (prefix fxk) service repair manual (fxk00...fjkskedmme
This document provides instructions for removing and installing the crankshaft and crankshaft gear on Caterpillar 3064 and 3066 engines. It outlines the required tools and step-by-step procedures for removing components like the main bearings, connecting rod caps, and crankshaft. Instructions are provided for checking clearances and installing each part in reverse order. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 323 d l excavator (prefix cwg) service repair manual (cwg0000...fjskksmem
The document provides instructions for removing and installing the crankshaft on a Caterpillar C6.4 engine. To remove the crankshaft, the front housing, rear seal, flywheel housing and oil pan must first be removed. Then the connecting rod caps, main bearing caps and pistons can be taken off to allow removal of the crankshaft. Installation follows the reverse order, with care taken to clean parts and apply specified torques. End play must be checked after installation is complete.
The document provides instructions for removing and installing a fuel injection pump on a 320DL excavator with a C6.4 engine. It describes:
1) Removing components like hoses, tubes, brackets and gears to access the fuel injection pump.
2) Using identification marks and tooling to properly align gears during removal and installation.
3) Cleaning components thoroughly before installation to prevent contamination.
4) Installing the fuel injection pump by reversing the removal steps and ensuring proper torque of fasteners.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
The document provides instructions for removing and installing various engine components on a Caterpillar 330D2 excavator, including the engine oil pump, water pump, water temperature regulator, and flywheel. The procedures note required tools and safety precautions. Components must be clean and free of damage, with replacement of worn parts. Proper torque values are specified for reinstallation of components.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjsekmsmmes
This service manual provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and access the valves. The springs must be removed and installed in pairs per cylinder to ensure proper valve timing. Technicians are advised to clean all parts thoroughly and position the pistons carefully before compressing the springs.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 323 d excavator (prefix sdc) service repair manual (sdc00001 ...soeldksejdksem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, brake piston, barrel assembly, and shaft assembly. It then provides assembly instructions in 26 steps, placing components back into the travel motor in reverse order, and noting to clean parts and apply lubricants. Precise positioning and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in reverse order, noting specific installation procedures and component orientations. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f7fujksekmdm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in the reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damaging components and ensure correct assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying pipe sealant to seal surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...zan2736ban
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. It then lists 13 steps for assembling the travel motor, including installing seals, keys, cam plate and other components in the reverse order of disassembly. Safety precautions are provided to contain fluids and properly handle components.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...idkdkddmd
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar cat 323 d l excavator (prefix nzf) service repair manual (nzf0000...fjjsekmsmmes
This service manual provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.6 engine. The procedure involves using special tools to compress the valve springs, remove the keepers, and access the valves. The springs must be removed and installed in pairs per cylinder to ensure proper valve timing. Technicians are advised to clean all parts thoroughly and position the pistons carefully before compressing the springs.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 330 f excavator (prefix hck) service repair manual (hck00001 ...fjskkksmemm
The document is a service repair manual that provides instructions for disassembling a 330F excavator travel motor. It outlines 28 steps to fully disassemble the travel motor, removing components like the head assembly, housing assembly, brake piston, rotating group, pistons, and more. Various tools are required to remove fasteners and components. Safety precautions are provided throughout to warn of spring forces, pressurized fluids, and other hazards during disassembly.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Caterpillar cat 330 c mh excavator (prefix d3c) service repair manual (d3c000...jfdskekdmme
1) The document provides disassembly and assembly instructions for a 330C excavator travel motor.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then describes 13 steps for assembling the travel motor, including installing seals, bearings, springs, and securing components with bolts, pins, and retaining rings.
This document provides instructions for removing and installing various engine components on a Caterpillar 330 L excavator, including:
1. The cylinder head removal procedure involves removing fuel injection lines, exhaust manifold, rocker shaft and pushrods, and bolts holding the head to the cylinder block.
2. Installing the cylinder head requires cleaning surfaces, installing gaskets and bolts, adjusting valves, and reinstalling other removed components.
3. Removal of the spacer plate requires removing seals and installing a new gasket, while installation requires cleaning and installing the plate with new seals.
Caterpillar cat 312 b l track type excavator (prefix 9gr) service repair manu...fjskkksmemm
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 312B excavator engine. It describes:
1) Removing bolts and washers to detach the flywheel housing adapter, then removing the adapter.
2) Removing bolts to separate the inner ring from the flywheel, then removing the ring.
3) Lifting the flywheel out of the housing using straps and a lifting device, as it weighs 50kg.
The installation section reverses the removal steps, heating the ring gear if it was removed previously, and includes checking flywheel runout after installation.
Caterpillar cat 938 g ii wheel loader (prefix phn) service repair manual (phn...fjsjjekdkme
The document provides instructions for disassembling and assembling the transmission oil pump and relief valve (transmission hydraulic control) for a Caterpillar 938G II wheel loader. It includes detailed steps and illustrations for removing parts like gears, bearings, seals and covers. Tools required are also listed. The document is from a Caterpillar service manual and aims to guide maintenance technicians in properly servicing these components.
Caterpillar cat 312 c excavator (prefix bnn) service repair manual (bnn00001 ...fjskkksmemm
This document provides instructions for disassembling the final drive, travel motor, and travel counterbalance valve of excavator models 312C and 312C L. It outlines 19 steps to fully disassemble these components, including draining fluids, removing sprockets, valves, plates, seals, springs, and other internal parts. Safety notices are provided throughout to warn of hazards like stored energy, flying parts, and hot or pressurized fluids. Required specialty tools are listed at the beginning.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba00001 ...fjskkksmemm
This document provides instructions for removing and installing the engine oil bypass valve on Caterpillar 312C and 312C L excavators. It describes removing the threaded plug, shim, spring, and spring seat from the cylinder block. When installing, the spring seat, spring, shim, and threaded plug are reinstalled and tightened to the specified torque. The document also notes steps for checking components and adjusting valve opening pressure.
Caterpillar cat 323 d excavator (prefix sdc) service repair manual (sdc00001 ...soeldksejdksem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, brake piston, barrel assembly, and shaft assembly. It then provides assembly instructions in 26 steps, placing components back into the travel motor in reverse order, and noting to clean parts and apply lubricants. Precise positioning and alignment of parts is emphasized to prevent damage during reassembly.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in reverse order, noting specific installation procedures and component orientations. Proper cleaning and lubrication of parts is emphasized throughout.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f7fujksekmdm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...f8uesjdkdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...ufjksemd8ujd
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly section lists 24 steps to reinstall these components in the reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damaging components and ensure correct assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...jdkskmdmdm
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes precautions to ensure correct installation of components like the cam plate, piston shoe assemblies, and brake piston. Special tools may be required and clean hydraulic oil should be applied to sealing surfaces during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...prmy389342
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...8ufjsekddm8u
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying pipe sealant to seal surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fijsekkdmdm2w
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...zan2736ban
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It describes 27 steps to disassemble the travel motor by removing components like the head, brake piston, barrel assembly, shoe retainer, and shaft assembly. It then lists 13 steps for assembling the travel motor, including installing seals, keys, cam plate and other components in the reverse order of disassembly. Safety precautions are provided to contain fluids and properly handle components.
Caterpillar cat 323 d2 l excavator (prefix tdt) service repair manual (tdt000...idkdkddmd
The document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. It lists 27 steps for disassembly, which include removing the head, brake piston, barrel assembly, and other components. It then lists 13 steps for assembly, which involve installing seals, the shaft assembly, cam plate, springs and other parts back into the travel motor body. Safety precautions are noted, such as containing fluids and applying sealant to surfaces.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fujkskemdmdm4r
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during assembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual (TDT0000...km7seydwuhdw
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar Cat 323D2 L Excavator (Prefix TDT) Service Repair Manual Instant ...fskekkdmdmdm3e
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, brake piston, barrel assembly, and shaft. The assembly process describes 25 steps and includes installing seals, plates, springs and reassembling components in reverse order using alignment marks and clean hydraulic oil. Special care must be taken with components like the cam plate to ensure correct alignment during reassembly.
Caterpillar cat 323 d2 l excavator (prefix ycr) service repair manual (ycr000...fjkskekxsdcmdmme
This document provides instructions for disassembling and assembling the travel motor of a 323D2 L excavator. The disassembly process includes 27 steps to remove components like the motor head, check valves, fittings, piston guide, brake piston, barrel assembly and more. The assembly section lists 24 steps to reinstall these components in reverse order, noting proper orientation and cleaning of parts. Precautions are provided to avoid damage and ensure correct installation of components like the cam plate and piston shoe assemblies.
Similar to Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc00001 and up) (15)
Fiat kobelco sl30 b skid steer loader service repair manualidkkmdmd
This document is the service manual for an SL30B skid steer loader. It provides safety precautions and instructions for operating and servicing the loader. Some key points:
- Most accidents can be prevented by following simple safety rules and recognizing potential hazards before they cause accidents.
- Never attempt to clean, oil, or adjust the machine while it is in motion. Be certain any hydraulic, mechanical, or cable equipment is lowered to the ground before servicing.
- Wear appropriate protective equipment like safety hats, boots, gloves, and hearing protection when operating or servicing the loader.
- Only allow trained operators to use the loader. Do not let anyone ride as a passenger.
Fiat kobelco ex95 w mini wheel excavator service repair manualidkkmdmd
This document provides safety precautions for operating an excavator. It outlines general safety rules such as reading the operator's manual, understanding safety signs, wearing proper protective equipment, keeping the operator compartment clear, and following rules for starting, operating, stopping and maintaining the machine. It emphasizes avoiding hazards from moving parts by keeping body parts inside the operator compartment. It also notes checking for overhead and underground utilities and following limitations for the work site.
Fiat kobelco e80 mini crawler excavator service repair manualidkkmdmd
This document provides safety precautions and general guidelines for disassembling and repairing machines:
- Proper preparation is important, including cleaning the machine, recording inspection details, and arranging the work area. Safety gear should be worn and the machine secured before starting work.
- Hydraulic systems require special care when disassembling. Pressure must be released from lines and parts cleaned before removal. Match marks should be made and original assembly procedures followed.
- Inspection and cleaning of individual parts is important. Clearances and wear must be measured and documented. Reassembly follows the reverse of disassembly procedures, with new seals, grease, and sealants applied as needed. Thorough checks are required before
Fiat kobelco e50.2 sr mini crawler excavator service repair manualidkkmdmd
This document provides specifications and component information for an excavator model. It includes sections on machine dimensions, specifications and performance, machine and component weights, transportation requirements, crawler shoe and bucket types, and engine specifications including a performance curve. The document lists key components such as the engine, hydraulic pump, slewing motor, and travel motor. It also provides diagrams of machine dimensions and a table of weights.
Fiat kobelco e45.2 sr mini crawler excavator service repair manualidkkmdmd
This document provides safety precautions and general guidelines for repairing construction machinery. It discusses preparing for disassembly, safety during disassembly and assembly, handling hydraulic and electrical equipment, welding repairs, and environmental measures. Specific safety topics covered include cleaning machines before work, using proper protective equipment, relieving pressures in systems, and properly supporting lifted or raised components. Guidelines are provided for disassembling and assembling hydraulic systems and components.
Fiat kobelco e40.2 sr mini crawler excavator service repair manualidkkmdmd
This document provides safety precautions and guidelines for repairing and maintaining excavators. It covers preparing for disassembly, safety procedures for hydraulic and electrical systems, inspection and replacement of parts, reassembly, and installation. Proper preparation, cleaning, documentation, use of safety equipment, and bleeding of hydraulic systems are emphasized.
Fiat kobelco e35.2 sr mini crawler excavator service repair manualidkkmdmd
This document provides specifications and component information for an excavator model E30.2SR - E35.2SR. It includes:
1. A list of major components with corresponding numbers for identification.
2. Dimensions and performance specifications for the excavator, including machine weight, transport information, and bucket/shoe types.
3. Engine specifications, including performance curves for the model.
4. Sections on maintenance, systems, troubleshooting, and additional support data for the excavator. The document appears to be a workshop manual providing technical information to aid in repairs and maintenance of the machine.
Fiat kobelco e30.2 sr mini crawler excavator service repair manualidkkmdmd
This document provides safety precautions and guidelines for disassembling and repairing hydraulic excavators. It covers preparing for repairs, safety measures when disassembling parts, handling hydraulic and electrical components, and reassembling equipment. The document instructs technicians to clean machines before work, record inspection details, use proper safety gear, and bleed air from hydraulic systems after reassembly. Technicians are advised to take precautions for their safety and to properly handle and reinstall components.
Fiat kobelco e22 sr mini crawler excavator service repair manualidkkmdmd
This document provides safety guidelines and procedures for repairing heavy machinery:
- Technicians should thoroughly read manuals, clean machines, identify necessary parts, and document inspections before disassembling.
- Proper protective equipment like gloves, shoes, and glasses should be worn. Warning signs should be posted and engines stopped before work.
- Hydraulic and electrical systems need to be depressurized and disconnected from power sources. Guards and shields must be reinstalled after repairs.
- Welding, if required, should only be done by trained personnel. Fuel and hydraulic lines must be carefully inspected for damage.
- Procedures describe escaping from enclosed cabs and towing machines if necessary. Conversions between
Clark tmx12 25 forklift service repair manualidkkmdmd
This document provides instructions for safely maintaining electric forklifts. It discusses:
1. Identifying safety signs and messages and outlining safe maintenance practices such as blocking the wheels before working under the truck.
2. Procedures for lifting parts of the truck, including raising the drive wheels, chaining the upright, and jacking the rear or entire truck.
3. Instructions for securely tying down the truck for shipping.
Clark sf50 75s dl forklift service repair manualidkkmdmd
The document is a service manual that provides instructions for servicing a transmission. It begins with general information about the transmission components and operation. It then provides a section-by-section process to disassemble the transmission down to its core components in over 20 steps, including removing gears, shafts, bearings, seals, and other parts. Precautions are given to clean parts thoroughly to prevent dirt intrusion during repair.
Clark sf15 20 slc forklift service repair manualidkkmdmd
This 3-sentence summary provides the high-level and essential information from the document:
This service manual provides technical information for repair and maintenance of various models of forklifts, including safety precautions, general repair procedures, and standards conversions. It is divided into sections covering each main system, with chapters addressing topics like the engine, electrical system, and safety protocols. Technicians are directed to use proper tools and follow safety guidelines to prevent injury when working on forklifts.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Real-time driver monitoring is one of the easiest ways to make fleet management efficient as well as seamless. Connected vehicle solutions such as fleet GPS trackers and associated software help businesses in several ways. Refer to the post below for more details.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i01219550
Travel Motor - Disassemble
SMCS - 4351-015
Disassembly Procedure
Start By:
a. Remove the travel motor.
Reference: Refer to Disassembly and Assembly, "Travel Motor - Remove" in this manual.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the outside of the travel motor prior to disassembly.
2. Fasten the travel motor to a suitable holding fixture in a vertical position. The weight of the
travel motor is 60 kg (132 lb).
1/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
3. 3. Put an alignment mark across the head and the body of the travel motor for assembly
purposes. The head must be reinstalled in the head's original position on the body of the
travel motor.
Illustration 1 g00510326
Note: During the removal of head (2) from the body of the travel motor, be careful not to
scratch or damage the mating surfaces of the components.
4. Remove socket head bolts (1).
5. Remove head (2) from the body of the travel motor.
Illustration 2 g00510341
2/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
4. Illustration 3 g00510349
6. Turn over head (2).
7. Remove O-ring seal (6), shims (5), port plate (4), and bearing (3) from the head.
8. Remove the two check valve assemblies from the head.
Note: There is a retainer under spring (9). This retainer is a press fit in head (2). Do not
remove the retainer.
9. Insert a dowel rod with a small diameter into hole (X). Tap the dowel rod with a plastic
hammer in order to remove spring (9), poppet (8) and seat (7) from the head.
Illustration 4 g00510351
10. Remove three fittings (10) and plugs (11) from the head. Remove the O-ring seal from each
fitting.
Illustration 5 g00510352
11. Remove three O-ring seals (12) and washer set (13) from the body of the travel motor.
12. Place a shop towel over brake piston (14). Retain brake piston (14) by hand, and apply
approximately 525 kPa (75 psi) of shop air pressure to brake release port (Y). Make sure
that the shop air pressure is free of water. Brake piston (14) will move up the piston guide,
and out of the piston guide. Remove brake piston (14) from the body of the travel motor.
3/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
5. Illustration 6 g00510353
13. Remove O-ring seal (15) from the brake piston. Remove backup ring (16) from the brake
piston.
14. Remove O-ring seal (17) from the brake piston. Remove backup ring (18) from the brake
piston.
Illustration 7 g00510356
15. Remove piston guide (19), five friction plates (20) and the four steel plates from the body of
the travel motor.
Illustration 8 g00510359
4/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
6. 16. Remove O-ring seal (21) from the piston guide. Remove backup ring (22) from the piston
guide.
Illustration 9 g00510365
Note: Do not allow the components of barrel assembly (23) to come apart during the
removal from the travel motor. All of the components in the barrel assembly must be
reinstalled in the component's original location.
17. Use two large screwdrivers, as shown. Slowly remove barrel assembly (23) from the body
of the travel motor. Do not allow the components to fall apart.
Illustration 10 g00510502
Note: Shoe retainer (24) and piston shoe assemblies (25) are not serviced separately. Prior
to the removal of the shoe retainer and the piston shoe assemblies from barrel (26), put
identification marks on piston shoe assemblies (25) for assembly purposes. Identification
marks are used to identify the piston shoe assembly's location in shoe retainer (24) and
barrel (26). The piston shoe assemblies must be reinstalled in the piston shoe assembly's
original bores in the shoe retainer and the barrel.
18. Remove shoe retainer (24) and piston shoe assemblies (25) from barrel (26). Separate the
piston shoe assemblies from the shoe retainer.
5/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
7. Illustration 11 g00510504
19. Remove guide (27), spacer (28) and springs (29) from the barrel.
Illustration 12 g00510547
20. Remove cam plate (30) from the body of the travel motor.
Illustration 13 g00510550
21. Remove two keys (31) and the two locating pins (not shown) from the body of the travel
motor.
6/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
8. Illustration 14 g00510551
22. Remove O-ring seal (33) from the body of the travel motor.
23. Use a soft faced hammer to remove shaft assembly (34) from the body of the travel motor.
Remove the shaft assembly in the direction that is indicated by the arrow. Refer to
Illustration 14.
Illustration 15 g00510595
24. Remove retaining rings (35) from each side of bearing (36). Push shaft (34) out of bearing
(36) with a press.
Illustration 16 g00510598
7/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
9. 25. Remove inner race (37) from shaft (34).
Illustration 17 g00510599
26. Remove lip seal (38) from the body of the travel motor.
Illustration 18 g00510605
27. Remove two stoppers (39) and the two pistons from the body of the travel motor.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:52:58 UTC+0800 2020
8/8
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i01706705
Travel Motor - Assemble
SMCS - 4351-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
1. Make sure that all of the components of the travel motor are thoroughly clean and free of
dirt and debris prior to assembly.
Illustration 1 g00510595
2. Install retaining ring (35) in the groove on shaft (34).
3. Install bearing (36) on shaft (34) with a press. Install the bearing until the bearing contacts
the retaining ring.
1/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
11. 4. Install the other retaining ring on the opposite side of bearing (36).
Illustration 2 g00510598
5. Install inner race (37) on the end of shaft (34) until the inner race is seated against the
shoulder on the shaft.
Illustration 3 g00651891
(a) Body
6. Apply a thin coat of 5P-3413 Pipe Sealant on Surfaces (Y) of the body of the travel motor.
7. Use Tooling (A) in order to install lip seal (38).
8. Install lip type seal (38) in the body of the travel motor. Install the lip seal so that the sealing
lip is facing in the direction that is shown. Make sure that the lip seal contacts the
counterbore in the body of the travel motor.
Note: Slowly rotate shaft assembly (34) during the installation in order to make sure that the
shaft assembly does not bind in the body of the travel motor.
9. Apply clean hydraulic oil on the lip of lip seal (38).
2/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
12. 10. Use a press to install shaft assembly (34) in the body of the travel motor. Slowly rotate the
shaft during the installation in order to make sure that the shaft does not bind. Make sure
that the bearing on the shaft contacts the counterbore in the body of the travel motor.
Illustration 4 g00651960
NOTICE
The locating pin on each key is not centered. In order to prevent
damage to the barrel assembly during assembly of the travel motor, the
keys must be installed as shown. Also, the keys must be installed in the
key's original location in the body of the travel motor.
11. Install the two locating pins and two keys (31) in the body of the travel motor, as shown.
Illustration 5 g00510547
3/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
13. 12. Install cam plate (30) in the body of the travel motor in the cam plate's original location.
Make sure that the two pistons and two keys (31) in the body of the travel motor engage
properly with the cam plate.
Illustration 6 g00510504
13. Install nine springs (29) in the barrel. Install spacer (28) and guide (27) on the barrel.
Illustration 7 g00878253
14. Install piston shoe assemblies (25) in the piston shoe assembly's original bores in shoe
retainer (24).
15. Apply clean hydraulic oil in the bores of the barrel and on piston shoe assemblies (25).
Install the piston shoe assemblies with the shoe retainer in the piston shoe assembly's
original bore in barrel (26).
NOTICE
Make sure that the cam plate is correctly engaged with the two pistons
in the body of the travel motor prior to installing the barrel assembly.
When the body of the travel motor is tilted to allow the installation of
the barrel assembly, the cam plate can slide off of the two pistons. The
remaining parts of the travel motor can be assembled with the cam
plate in the incorrect position.
4/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
14. Extensive damage will result from the incorrect installation of the cam
plate. Follow the exact installation procedure to prevent damage.
16. Apply clean hydraulic oil on the sliding surfaces of the cam plate, on the piston shoe
assemblies and on the splined shaft of the travel motor.
Illustration 8 g00485953
17. Route a piece of strong string through an opening for the cam plate tension adjusters. Route
the string over the sliding surface of cam plate (30) and through the opposite opening for the
cam plate tension adjusters. Hold the string taut in order to keep cam plate (30) correctly
engaged with keys (31). Keep the string taut and position the body of the travel motor on the
body's side. Do not release the tension on the string at this time. Install barrel assembly (23)
as a unit on the shaft. Pull the string out of the body of the travel motor. It may be necessary
to pull the barrel assembly and the piston shoe assemblies away from the cam plate slightly
in order to release the string.
Illustration 9 g00651967
5/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
15. 18. Install O-ring seal (21) and backup ring (22) on piston guide (19), as shown.
Illustration 10 g00510356
19. Place the body of the travel motor in a vertical position.
20. Apply clean hydraulic oil on five friction plates (20) and the four steel plates. Install the
plates in alternating order in the body of the travel motor. Start with a friction plate and end
with a friction plate.
21. Install piston guide (19) in the body of the travel motor until the piston guide contacts the
counterbore in the body of the travel motor.
Illustration 11 g00878297
Note: Make sure that brake piston (14) is thoroughly clean and free of dirt and debris.
22. Install O-ring seal (16). Install backup ring (15).
23. Install O-ring seal (17). Install backup ring (18).
6/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
16. 24. Apply a thin coat of hydraulic oil on the surfaces of piston (14) which contact the body of
the travel motor. Install piston (14) in the body of the travel motor by hand. It may be
necessary to use a soft faced hammer to seat the piston correctly.
Illustration 12 g00878299
Illustration 13 g00878239
25. Install washer set (12) in piston (14), as shown.
26. Install O-ring seals (13) in the body of the travel motor, as shown.
7/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
17. Illustration 14 g00510605
27. Install the two pistons and two stoppers (39) in the housing of the travel motor. Tighten the
stoppers to a torque of 140 ± 14 N·m (105 ± 10 lb ft).
Illustration 15 g00510351
28. Install the O-ring seals on fittings (10). Apply 5P-3413 Pipe Sealant on the threads of
fittings (10). Install the fittings in the head, as shown.
29. Install plugs (11) in the head. Tighten each plug to a torque of 15 ± 2 N·m (11 ± 1 lb ft).
Illustration 16 g00510349
8/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
18. Illustration 17 g00510341
30. Apply a thin coat of 9S-3263 Thread Lock Compound on the threads of the two check
valves. Install the check valves in the head.
31. Install seat (7), poppet (8) and spring (9) in the head at Location (X).
32. Install O-ring seal (6) in the head, as shown.
33. Install bearing (3) in the head until the bearing contacts the counterbore in the cover.
34. Apply 1U-6396 O-Ring Assembly Compound on port plate (4). Install the port plate in the
port plate's original position on the motor cover.
35. Use a shim or shims (5) so that the following requirements are met.
Note: During the following checks, turn the travel motor output shaft in a clockwise
direction.
a. The travel motor output shaft does not rotate with an applied torque of 440 N·m
(325 lb ft) or more with the parking brake release port open.
b. The travel motor output shaft rotates with an applied torque of 29 N·m (21 lb ft) or
less when the parking brake release port is pressurized to 780 kPa (115 psi) with both
the inlet port and the outlet port open to the hydraulic oil tank.
Note: It may be necessary to remove head (2) several times in order to determine the correct
thickness of shim or shims (5) that are used to adjust the rolling torque of the travel motor
output shaft.
36. Apply a thin layer of 5P-0960 Molybdenum Grease on shim or shims (5). Install the shim or
shims on the head. The grease will hold the shim or shims in place during the installation of
the head. Install the head on the body of the travel motor.
9/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
19. Illustration 18 g00510326
37. Place head (2) in the head's original position on the travel motor. Install socket head bolts
(1) that secure the head. Tighten the socket head bolts to a torque of 175 ± 18 N·m
(130 ± 13 lb ft).
NOTICE
To prevent possible damage to the travel motor, fill the unit with oil at
least to the fill port before operating the machine. Refer to the
Operation and Maintenance Manual for the correct oil specification.
End By:
a. Install the travel motor. Refer to Disassembly and Assembly, "Travel Motor - Install" in this
manual.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:53:57 UTC+0800 2020
10/10
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engi...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i03524320
Travel Motor - Install
SMCS - 4351-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-7692 Threaded Rod M16 by 381mm 2
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Thoroughly clean the mating surfaces of the travel motor and the final drive.
1/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
21. Illustration 1 g00651795
2. Install a new O-ring seal (5) . Apply clean hydraulic oil on O-ring seal (5) .
Illustration 2 g00707267
3. Attach a suitable lifting device to travel motor (4) , as shown. The weight of travel motor (4)
is approximately 57 kg (125 lb).
Illustration 3 g00944825
2/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
22. 4. Carefully install travel motor (4) on Tooling (A) . Slide travel motor (4) into the final drive.
5. Install bolt (2A) that secures travel motor (4) to the final drive.
6. Remove Tooling (A) .
Illustration 4 g00707275
Typical example
7. Install bolts (2) .
8. Connect hose assemblies (3) and (1) .
9. Fill the final drive with oil. Refer to Operation and Maintenance Manual, "Lubricant
Viscosities" for the proper oil viscosity. Refer to Operation and Maintenance Manual, "Final
Drive Oil Level - Check" for the correct filling procedure.
10. Install high efficiency filters in place of the pilot filter, the case drain filter, and the return
filter.
Note: High efficiency filters should not be run for more than 250 hours before you change
back to the standard filters.
11. Obtain a hydraulic oil sample from the main S·O·S port. Refer to Operation and
Maintenance Manual, "Sampling Interval and Location of Sampling Valve" for the correct
location.
12. If the S·O·S sample exceeds ISO 18/15, flush the hydraulic system. Refer to Contamination
Control Guideline, SEBF8447 for further information.
End By: Install the counterbalance valve. Refer to Disassembly and Assembly, "Counterbalance
Valve (Travel) - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:54:57 UTC+0800 2020
3/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i05453056
Final Drive - Remove
SMCS - 4050-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C
154-6184 Forcing Bolt (M 20) 2
154-6185(1)
Forcing Bolt (M 24) 2
(1)
For Use on 329 and 330 sales models
Start By:
a. Separate the track assembly.
b. Remove the travel motor.
1/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
24. Illustration 1 g00489826
Typical Example
Note: Adjust the height of Tooling (A) so that there is sufficient clearance between the
sprocket and the track for the removal of the final drive.
1. Lift the side of the machine in order to install Tooling (A) under the frame, as shown.
Illustration 2 g00712767
2. Fasten Tooling (B) and a suitable lifting device to final drive (1), as shown. Put a slight
lifting tension on the final drive.
Illustration 3 g00712737
2/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
25. Note: Mark the orientation of bolt holes (2) for the travel motor for installation purposes.
3. Remove bolts (3) and the washers from the final drive.
Illustration 4 g00712749
4. Use Tooling (C) in order to remove the final drive from the frame.
5. Carefully remove final drive (1). The weight of final drive (1) and the sprocket is
approximately 312 kg (688 lb).
6. Remove Tooling (C) from the frame.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Sep 5 00:55:57 UTC+0800 2020
3/3
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR SDC
Configuration: 323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
323D Excavator Machine Systems
Media Number -RENR7500-07 Publication Date -01/02/2012 Date Updated -14/02/2012
i05453130
Final Drive - Disassemble
SMCS - 4050-015
S/N - BYM1-UP
S/N - CWG1-UP
S/N - CYD1-UP
S/N - DCJ1-UP
S/N - DKW1-UP
S/N - GTF1-UP
S/N - JLG1-UP
S/N - LFL1-UP
S/N - NDE1-UP
S/N - NES1-UP
S/N - PBE1-UP
S/N - PBM1-UP
S/N - RAC1-UP
S/N - SDC1-UP
S/N - SED1-UP
S/N - WGC1-UP
1/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
28. S/N - WNE1-UP
S/N - YSD1-UP
S/N - ZMF1-UP
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
2/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...
29. Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
Illustration 3 g00708091
3/11
323D & 323D L Excavator SDC00001-UP (MACHINE) POWERED BY 3066 Engine...
2020/9/5
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisw...