This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
What Does the Active Steering Malfunction Warning Mean for Your BMWTanner Motors
Discover the reasons why your BMW’s Active Steering malfunction warning might come on. From electrical glitches to mechanical failures and software anomalies, addressing these promptly with professional inspection and maintenance ensures continued safety and performance on the road, maintaining the integrity of your driving experience.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05834261
Unit Injector - Remove and Install
SMCS - 1290-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 268-1968 Pry Bar 1
B - Scotch Brite 1
C
1U-5718 Vacuum Pump 1
169-7372 Bottle Assembly 1
4C-4057
Clear Plastic Tubing
7.92 mm (0.312 inch) OD
1
4C-4055
Clear Plastic Tubing
6.35 mm (0.250 inch) OD
D 9U-5470 Reamer 1
E 4C-6161 Tube Brush 1
F 9U-6862 Tapered Brush 1
G 4C-6774 Vacuum Gun Kit 1
H 4C-5027 Tap Wrench 1
Start By:
1/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
3. A. Remove the valve mechanism cover.
B. Remove the fuel injection line.
C. Remove Compression Brake (If Equipped).
Illustration 1 g01264292
Illustration 2 g01264293
Note: Do not remove the quill tube. This action will reduce the risk of contamination to the
system.
1. Fully loosen quill tube nut (1) . Pull quill tube (1) out of the bore until you see O-ring seal
(2) . This action will ensure that the injector does not contact the quill tube during removal.
At this time, inspect O-ring seal (2) for wear or for damage. Replace the O-ring seal if
necessary.
2/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
4. Illustration 3 g02161166
Typical Example
2. Disconnect harness assembly (3) from the unit injector.
Illustration 4 g02161316
Typical Example
3. Remove bolt (5) from clamp (6) .
Note: When possible, remove the unit injector by hand by twisting the unit injector and
pulling upward. Be sure not to strike the unit injector during the removal procedure.
4. If unit injector (4) cannot be removed by hand, go to Step 5.
3/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
5. Illustration 5 g02161361
Typical Example
Note: Do not damage the unit injector during removal. Side loading may damage to the unit
injector.
5. Position Tooling (A) under unit injector clamp (6) . Carefully remove unit injector (4) from
the cylinder head.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Evacuate as much fuel and oil as possible from the cylinder head before installing the unit
injector. Several evacuations may be necessary. Use Tooling (C) to remove the fuel and oil
from the cylinder.
4/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
6. Note: Tooling (F) is available to clean loose material from the sleeve bore and the cylinder.
2. Clean the carbon from the sleeve, the sleeve bore, and the end of the unit injector. Clean the
carbon from the seat area that is inside of the cylinder head. A fine grade of Tooling (B) is
preferred. Clean the carbon from the cylinder head. If the sleeve of the unit injector has been
removed, use Tooling (D) to remove only carbon from the surface of the sleeve. If the
sleeve of the unit injector is installed, use Tooling (E) to clean the carbon deposit from the
inside of the sleeve.
The following procedure is the preferred method of cleaning the sleeve bore.
Place a 38 mm (1.5 inch) square piece of Scotch Brite material on the end of Tooling (F) .
Twist Tooling (F) with Tooling (H) against the lower surface of the sleeve bore.
The surface should be cleaned until the surface is smooth and shiny. The entire sleeve bore
should be cleaned in order to remove any loose carbon particles.
Note: Tooling (G) is available to clean loose material from the sleeve bore and the cylinder.
NOTICE
The correct procedures and tooling specifications must always be used.
Failure to follow any of the procedures may result in damage,
malfunction, or possible engine failure.
Illustration 6 g01355602
Note: Replace the O-ring seals on the injector.
3. Install O-ring seal (9) and O-ring seal (10) on unit injector (4) . Lubricate O-ring seal (9) , O
-ring seal (10) , and the sleeve bore of the unit injector sparingly with clean engine oil.
4. Record the serial number for the injector and the injector confirmation code. When you
install a new unit injector, the E-Trim value must be programmed into the Engine Control
Module. For more information, refer to Troubleshooting, "Injector Trim File - Install".
5/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
7. Illustration 7 g02161415
Illustration 8 g01264293
Note: Verify quill tube (1) is positioned out of the bore enough to see O-ring seal (2) . This
action will ensure that the injector does not contact the quill tube during installation.
5. Place unit injector (4) into the bore. Make sure that the key (7) for the unit injector fits into
slot (8) in the cylinder head.
6/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
8. Illustration 9 g02161316
Note: Use new socket head bolt (5) .
6. Position unit injector clamp (6) with the label "C9" in the up position. Install socket head
bolt (5) into unit injector clamp (6) . Tighten socket head bolt (5) to a torque of 28 ± 3 N·m
(21 ± 2 lb ft) in order to secure unit injector (4) .
Illustration 10 g02161166
7. Connect harness assembly (3) to the unit injector.
7/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
9. Illustration 11 g01355441
Illustration 12 g01355608
Note: Check the O-ring seal for wear or for damage. If necessary, replace the O-ring seal.
8. If the O-ring seal was damaged, perform Step 8.a and Step 8.b.
8/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
10. Illustration 13 g02077582
a. Inspect the Sealing Surface (A) for damage. Replace quill tube (1) if damage was
found.
b. Lubricate new O-ring seal (2) with clean engine oil. Install new O-ring seal (2) .
9. Lubricate the O-ring seal, the nut face, and the threads with clean engine oil. Insert quill
tube (1) into the bore with the ball on the right side. Once the quill tube has bottomed out,
rotate the quill tube until the ball engages with the slot. The quill tube should drop slightly
when the ball is engaged with the slot. This action will install quill tube (1) . Ensure that the
ball is in alignment with the slot for quill tube (1) . Tighten the nut for quill tube (1) to a
torque of 70 ± 3 N·m (52 ± 2 lb ft).
End By:
a. Install Compression Brake (If Equipped).
b. Install the valve mechanism cover.
c. Install the fuel injection line.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:42:58 UTC+0800 2020
9/9(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
11. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05282771
Unit Injector Sleeve - Remove and Install
SMCS - 1713-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A - Tap 7/8-9 NC 1
B
1A-5576 Bolt 1
8C-6913 Hard Washer 7
C 221-9803 Rubber Stopper 1
D 1P-0510 Driver Gp 1
E 4C-5552 Large Bore Brush 1
F 4C-9507 Retaining Compound 1
Start By:
a. Remove the unit injectors.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the coolant from the cooling system into a suitable container for storage or disposal.
Refer to Operation and Maintenance Manual, "Refill Capacities and Recommendations".
Illustration 1 g02163825
2. Position Tooling (C) at the bottom of the unit injector sleeve (1).
3. Coat Tooling (A) (not shown) with clean grease. Use Tooling (A) to cut threads into unit
injector sleeve (1).
4. Use Tooling (B) in order to remove unit injector sleeve (1). Discard the unit injector sleeve
(1).
Installation Procedure
1. Thoroughly clean the bores for the unit injectors with Tooling (E).
2/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
13. Illustration 2 g02164118
2. Apply clean engine oil to O-ring seals (2). Install O-ring seals (2) on unit injector sleeve (1).
3. Apply a thin coating of Tooling (F) around the outer circumference of unit injector sleeve
(1) at Area (G).
4. Position unit injector sleeve (1) in the cylinder head. Use a hammer and Tooling (D) in
order to install unit injector sleeve (1) in the cylinder head.
Note: Allow Tooling (F) to cure for 2 hours at 21 °C (70 °F) before filling the engine with
fuel or coolant. Longer curing time is required for lower temperatures.
5. Fill the cooling system with coolant to the correct level. Refer to Operation and
Maintenance Manual, "Refill Capacities and Recommendations".
End By:
a. Install the unit injectors.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:43:54 UTC+0800 2020
3/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
14. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05831969
Turbocharger - Remove and Install - Cooled by Coolant
SMCS - 1052-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description QTY
A - Loctite C5A Copper Anti-Seize 1
1. Drain the cooling system into a suitable container for storage or disposal. Refer to Operation
and Maintenance Manual, "Cooling System Coolant (ELC) - Change".
Illustration 1 g02377418
2. Disconnect tube assemblies (1) and (2) .
3. Disconnect hose (3) .
1/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
15. Illustration 2 g02377458
4. Disconnect hose assemblies (4) and (5) .
Illustration 3 g02377876
5. Remove four nuts (7) and remove turbocharger (6) . Discard nuts (7) and remove the gasket.
2/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
16. Illustration 4 g02377938
Note: Band clamps (8) , (9) and (10) , are one time use parts. Discard the clamp assemblies
if the clamps are loosened.
6. Remove band clamp (8) in order to separate the adaptor from the turbine housing. Discard
band clamp (8) .
7. Remove band clamp (9) in order to separate the turbine housing from the cartridge
assembly. Discard band clamp (9) .
8. Remove band clamp (10) in order to separate the compressor housing from the cartridge
assembly. Discard band clamp (10) .
9. Remove adapters (11) from the cartridge assembly.
Installation Procedure
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
1. Install the turbocharger (6) in the reverse order of removal.
a. Install new band clamp (9) . Tighten band clamp (9) to a torque of 18 N·m (159 lb in).
Loosen band clamp (9) and retighten the clamp to a torque of 13.6 ± 1.2 N·m (120 ±
11 lb in).
b. Install new band clamp (10) . Tighten band clamp (10) to a torque of 13.6 ± 1.2 N·m
(120 ± 11 lb in).
c. Install new band clamp (8) . Tighten band clamp (8) to a torque of 12 ± 4 N·m (106 ±
35 lb in).
d. Apply Tooling (A) to the threads of new nuts (7) prior to installation.
e. Tighten nuts (7) to a torque of 70 ± 5 N·m (52 ± 4 lb ft).
f. Put clean engine oil in the oil inlet of the turbocharger after assembly or before
installation. This action will provide lubrication during start-up and during storage.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:44:50 UTC+0800 2020
3/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
17. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i03907730
Solenoid Valve (Exhaust Balance) - Remove and Install
SMCS - 1052-010-VL
Removal Procedure
Illustration 1 g02148775
1. Disconnect harness assembly (2). Disconnect tube assemblies (1) and (3).
2. Remove solenoid balance valve (4).
Installation Procedure
1. Install the solenoid balance valve (4) in the reverse order.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:45:45 UTC+0800 2020
1/1(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
18. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05295284
Air Control Valve - Remove and Install
SMCS - 108A-010
Removal Procedure
Illustration 1 g02161617
View of the Air Control Valve which is located on the Clean Emissions Module.
1. Remove cable straps (2). Disconnect harness assemblies (1) and position the harness
assembly out of the way.
2. Remove tube assembly (3).
1/2(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
19. Illustration 2 g02161618
3. Loosen clamp assembly (5). Remove bolts (4) and remove air control valve (6).
Illustration 3 g02161693
4. Remove bolts (11). Separate housings (10) and (7) from the air control valve actuator (8).
Remove both seals (9) from the housings.
Installation Procedure
1. Install air control valve (8) in the reverse order of removal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:46:41 UTC+0800 2020
2/2(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
20. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05295410
Exhaust Cooler (NRS) - Remove and Install
SMCS - 1087; 108C-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
207-1600(1)
Rubber Lubricant 1
207-1601 Rubber Lubricant 1
(1)
For Use in EAME
Note: Due to various machine configurations, components will need to be removed that are not
called out in this procedure. Refer to the appropriate manual to remove the necessary components.
1. Refer to Operation and Maintenance Manual, "Cooling System Coolant - Change" for the
proper draining and filling procedures.
Note: Step 2 through Step 4 may not apply to all engine configurations. If so, then start with
Step 5.
1/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
21. Illustration 1 g02763336
2. Disconnect hose assembly (2).
3. Remove hose (1), hose (3), the adapters, and the clips.
Illustration 2 g02763418
4. Position oil level gauge (4) out of the way. Remove bracket assembly (5).
Illustration 3 g02763456
5. Loosen band clamps (6) and the hose.
2/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
22. Note: The band clamps and hose are one-time use components. Discard upon removal and
install new.
6. Loosen clamps (10). Remove bolts (8) and (11).
7. Remove exhaust cooler (7). Remove bellows (9) and clamps (10) from exhaust cooler (7).
Note: Note the orientation of the bellows. The arrow should point toward the exhaust
cooler.
8. Remove tubes (12). Remove the O-ring seals from tubes (12).
Installation Procedure
1. Install exhaust cooler (7) in the reverse order of removal.
a. Apply a light coating of Tooling (A) to the bores and the O-ring seals for tubes (12).
b. Install new bellows (9) and clamps (10). Tighten clamp assemblies (10) to a torque of
7.5 ± 1 N·m (66 ± 9 lb in).
Note: The arrow on the bellows should point toward the exhaust cooler. Total
misalignment for the bellows is 1.50 mm (0.06 inch) lateral and 1.50 mm (0.06 inch)
axial.
c. Tighten bolts (11) to a torque of 55 ± 10 N·m (41 ± 7 lb ft).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:47:37 UTC+0800 2020
3/3(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i05295411
Exhaust Gas Valve (NRS) - Remove and Install
SMCS - 108N-010; 5510
Removal Procedure
Illustration 1 g02150623
1. Disconnect clamp assembly (1). Disconnect harness assemblies (2) and disconnect hose
assemblies (4). Disconnect clamp assembly (3).
1/2(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
25. Illustration 2 g02150662
2. Remove four bolts (5) and remove exhaust gas valve (6).
Installation Procedure
1. Install exhaust gas valve (6) in reverse order of removal.
a. Tighten clamp assembly (3) to a torque of 8.5 ± 2 N·m (75 ± 18 lb in).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sun Jun 7 18:48:33 UTC+0800 2020
2/2(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...
26. Shutdown SIS
Previous Screen
Product: INDUSTRIAL ENGINE
Model: C9.3 INDUSTRIAL ENGINE CS9
Configuration: C9.3 Industrial Engine CS900001-UP
Disassembly and Assembly
C9.3 Industrial Engine
Media Number -UENR0183-02 Publication Date -01/06/2014 Date Updated -06/06/2014
i03513485
Exhaust Gas Valve (NRS) - Disassemble
SMCS - 108N-015; 5510
Disassembly Procedure
Start By:
a. Remove the Exhaust Gas Valve.
Illustration 1 g01845346
1. Remove temperature sensor (1).
2. Remove bolts (2). Separate actuator assembly (3) from the valve housing (4).
1/2(W)
w
2020/6/7
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/siswe...