- The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and valve seat inserts on a C6.4 engine.
- It describes the required tools and gives step-by-step procedures for removal and disassembly, including cleaning, inspection, and installation of new parts.
- Precautions are provided to keep parts clean, contain fluids, and wear protective equipment when working with spring-loaded components.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 325 c l excavator (prefix btd) service repair manual (btd0000...fjkskedmme
The document provides step-by-step instructions for disassembling and assembling the piston motor of an excavator. It lists 22 steps for disassembly, which include removing the key, cover, port plate, bearings, valve assembly, and other components. It then lists 16 steps for assembly, which involve installing components in reverse order and ensuring proper seating and alignment of parts like bearings, seals, and the rotating group. Cleanliness is emphasized throughout and special tools are required for tasks like compressing springs.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 304.5 e mini hydraulic excavator (prefix fxt) service repair ...fjskekfseik
The document provides instructions for removing and installing piston and connecting rod assemblies in an engine. Key steps include:
1. Removing the cylinder head and oil pan before removing the piston and connecting rod.
2. Pushing the connecting rod and piston out of the cylinder block after removing the connecting rod cap and bearings.
3. Reversing the removal procedures to install the piston and connecting rod assemblies, ensuring correct orientation and applying lubricant to moving parts.
Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf0000...fjjsekmsmmes
This document provides instructions for removing and installing inlet and exhaust valve seats in a C6.4 engine. It describes using various tools to remove the valves, valve guides, and valve seat inserts from the cylinder head. It also details how to clean, inspect, and lubricate components before reinstalling the valve seat inserts, guides, and valves in the proper order and orientation. Protective equipment is recommended to safely compress springs during the process.
Caterpillar cat 325 c l excavator (prefix btd) service repair manual (btd0000...fjkskedmme
The document provides step-by-step instructions for disassembling and assembling the piston motor of an excavator. It lists 22 steps for disassembly, which include removing the key, cover, port plate, bearings, valve assembly, and other components. It then lists 16 steps for assembly, which involve installing components in reverse order and ensuring proper seating and alignment of parts like bearings, seals, and the rotating group. Cleanliness is emphasized throughout and special tools are required for tasks like compressing springs.
Caterpillar cat 305.5 e2 cr mini hydraulic excavator (prefix nc5) service rep...cdfzxs
The document provides instructions for removing and installing various engine components of a 305.5E2 CR Mini Hydraulic Excavator powered by a C2.4 engine, including the inlet manifold, inlet and exhaust valves, engine oil cooler, engine oil pump, water pump, and water temperature regulator. The procedures include draining fluids, removing fasteners and hoses, cleaning parts, and installing components in reverse order of removal while following safety notices.
Caterpillar cat 323 d l excavator (prefix pbe) service repair manual (pbe0000...fjjsekmsmmes
This document provides instructions for removing and installing the idler gear in the front gear group of a Caterpillar C6.4 engine. The removal procedure involves using various tools to remove the idler gear bolt, thrust plate, idler gear, bushing and idler shaft. The installation procedure specifies cleaning parts and using a press and driver group to re-install components in reverse order, checking backlash and end play tolerances.
Caterpillar cat 320 l track type excavator (prefix 2dl) service repair manual...fkjsekksmem
This document provides instructions for servicing components of Caterpillar excavator models 320, 320L, and 320N, including:
- Removing and installing inlet and exhaust valve seals
- Removing the engine oil filter base
- Installing the engine oil filter base
- Removing the engine oil cooler
- Disassembling the engine oil cooler
- Reassembling the engine oil cooler
- Installing the engine oil cooler
The document includes diagrams and step-by-step instructions for maintenance procedures. Technicians are advised to keep components clean and contain fluids properly during repair.
Caterpillar cat 320 d l excavator (prefix kgf) service repair manual (kgf0000...fkjsekksmem
This document provides instructions for disassembling and assembling the travel motor of a 320D L excavator. The disassembly process includes 27 steps to remove components like the head, fittings, seals, brake piston, plates, and barrel assembly. The assembly section outlines 13 steps including installing seals, keys, cam plate, springs, and piston shoe assemblies back into the barrel assembly and body of the travel motor. Special care must be taken to align parts properly and not allow components to separate during disassembly and assembly.
Caterpillar cat 312 c excavator (prefix cba) service repair manual (cba01201 ...fjskkksmemm
The document provides instructions for removing and installing various engine components on Caterpillar 312C and 312C L excavators, including:
- Installing a crankshaft rear seal using a specific tool and applying retaining compound to mating parts.
- Removing and installing a flywheel housing which requires removing bolts and installing a new gasket.
- Removing a crankshaft pulley using a puller tool and removing a wear sleeve with a chisel if needed.
- Removing a crankshaft front seal by drilling holes and using a slide hammer puller.
- Installing a new crankshaft front seal with a specific installer tool.
- Procedures are provided for additional
Caterpillar cat 304.5 e mini hydraulic excavator (prefix fxt) service repair ...fjskekfseik
The document provides instructions for removing and installing piston and connecting rod assemblies in an engine. Key steps include:
1. Removing the cylinder head and oil pan before removing the piston and connecting rod.
2. Pushing the connecting rod and piston out of the cylinder block after removing the connecting rod cap and bearings.
3. Reversing the removal procedures to install the piston and connecting rod assemblies, ensuring correct orientation and applying lubricant to moving parts.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening fasteners to specified torques. Tools required are also listed.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The installation procedure specifies applying lubricant to new seals before reconnecting the governor components using the same special tools. Proper tightening torque is listed for bolts reinstalling the fuel injection control linkage.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel, crankshaft rear seal, and flywheel housing and installing a new crankshaft rear seal, gasket, and flywheel housing. Torque specifications and tightening sequences are provided for installing the components.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 320 d l excavator (prefix dhk) service repair manual (dhk0000...fkjsekksmem
This document provides instructions for removing and installing the boom cylinder on a 320D and 320D L excavator. It outlines the required tools and safety precautions. The removal process involves releasing hydraulic pressure, removing attachment points, and lifting the cylinder out of place. Reinstallation is the reverse of removal. Torque specifications are provided for correct assembly.
Caterpillar cat 325 f excavator (prefix ndj) service repair manual (ndj00001 ...hfjsekekmmd
The document provides instructions for disassembling and assembling the travel motor of a 325F excavator. It includes 30 steps for disassembly, removing components like the spring, spool, relief valve, head assembly, housing assembly and more. The 31 steps for assembly include installing seals, springs, pistons, cam plate, barrel assembly and ensuring proper alignment of components. Special tools and precautions are noted to properly release spring forces and prevent damage during assembly.
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar 330 excavator engine. It describes:
1. Using valve spring compressors and other tools to remove the valves, springs, and related components from the cylinder head.
2. Inspecting the valve springs and related components when removed.
3. Lubricating and installing the valves back into the cylinder head in the reverse order of removal.
4. Ensuring the valve keepers are properly seated using a soft faced hammer.
The summary covers the key steps and tools involved in removing and installing the inlet and exhaust valves per the document's instructions.
The document provides assembly instructions for installing a swing gear and bearing on an excavator. It lists required tools and parts. The procedure involves cleaning the swing gear and bearing, applying lubricant and sealant, lifting it into position using links, and securing it with bolts torqued to specification. Inner and outer dust seals are installed in seal grooves before completing reassembly of the undercarriage frame.
Caterpillar cat 305 e2cr mini hydraulic excavator (prefix pyr) service repair...fjskekfseik
The document provides instructions for removing and installing various engine components on a Caterpillar 305E2 CR mini hydraulic excavator powered by a C2.4 engine, including:
- Removing and installing the idler gear.
- Removing and installing the front housing.
- Removing and installing the valve mechanism cover.
- Removing and installing the rocker shaft and push rods.
- Disassembling and assembling the rocker shaft.
The procedures include lists of required tools and step-by-step instructions with illustrations. Safety notices are also provided regarding keeping parts clean and preventing injury from spring-loaded components.
This document provides instructions for removing and installing exhaust manifold, inlet manifold, valves, and valve guides on Caterpillar 325, 325L, and 325LN excavator models powered by a 3116 engine. The procedures include removing mounting bolts and studs, applying anti-seize compound, installing new gaskets, and tightening fasteners to specified torques. Tools required are also listed.
Caterpillar cat 311 c excavator (prefix cke) service repair manual (cke00001 ...fjskefkemms
This service repair manual provides instructions for removing and installing inlet and exhaust valve seals on models 311C and 311C U excavators. The procedures describe using a seal pick tool to remove old seals from valve guides and installing new seals. Safety notices are included to keep parts clean and contain fluids.
Caterpillar cat 313 f excavator (prefix nlg) service repair manual (nlg00001 ...fjjskekdmmse
This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
Caterpillar cat 305 cr mini hydraulic excavator (prefix dgt) service repair m...fjskekfseik
The document provides instructions for removing the swivel on a 305CR Mini Hydraulic Excavator. It lists the required tools and notes to release hydraulic pressure and remove the cab first. The procedure involves using plugs and caps to seal ports while removing 4 bolts to detach the swivel assembly.
This document provides instructions for installing a flywheel and removing and installing a wet back end flywheel housing on a Caterpillar 320 GC excavator. It describes using guide studs and lifting devices to position the heavy flywheel and housing. Torque specifications and tightening sequences are given for installing mounting bolts. Replacing seals, gaskets and dowels is also covered.
Caterpillar cat 325 f excavator (prefix rbw) service repair manual (rbw00001 ...hfjsekekmmd
This document provides instructions for disassembling and assembling the travel motor on 325F and 325F L excavator models. The disassembly procedure involves 25 steps to remove components like the motor head, fittings, seals, pistons, and more. The assembly procedure describes 22 steps and includes applying sealant and grease, installing components in their original positions, and using a string to ensure proper cam plate engagement during installation of the barrel assembly. Precise following of the procedures is emphasized to prevent damage to components.
Caterpillar cat 323 d l excavator (prefix sdc) service repair manual (sdc0000...fjskksmem
The document provides step-by-step instructions for disassembling and assembling a travel motor. It begins with disassembly instructions, listing 27 steps to remove components such as the head, check valves, fittings, seals, brake piston, plates, and shaft. It then provides assembly instructions in 25 steps, listing the components to be installed in reverse order, and noting to clean parts and apply oil or seals at various steps. Precise positioning and alignment of parts is emphasized to ensure proper reassembly.
This document provides instructions for removing and installing a governor and fuel injection control linkage on Caterpillar 325, 325L, and 325LN excavators powered by a 3116 engine. The removal procedure involves using special tools to disconnect tubes, pins, and clips connecting the governor to the engine. The installation procedure specifies applying lubricant to new seals before reconnecting the governor components using the same special tools. Proper tightening torque is listed for bolts reinstalling the fuel injection control linkage.
Caterpillar cat 312 c excavator (prefix bwh) service repair manual (bwh00001 ...fjskkksmemm
The document provides instructions for removing and installing a crankshaft pulley on a 312C excavator. The removal procedure involves using a puller tool to remove the pulley from the crankshaft. For installation, the pulley is pressed onto the crankshaft and secured with bolts that are tightened to the specified torque.
This document provides instructions for removing and installing a crankshaft rear seal and flywheel housing on a Caterpillar C4.4 engine. It describes removing the flywheel, crankshaft rear seal, and flywheel housing and installing a new crankshaft rear seal, gasket, and flywheel housing. Torque specifications and tightening sequences are provided for installing the components.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...dkdmidkkdk
This document provides instructions for removing and installing inlet and exhaust valves and valve guides on a C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and lubricate components before installation. Precautions are outlined to prevent injury and ensure proper assembly.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing valves, valve guides, and the engine oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing valves, valve guides, and installing new components. The document also describes draining coolant and removing bolts to take off the engine oil cooler.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjsekkdmme
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjjskekmsemm
This document provides the procedure for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine. The procedure involves using various tools to compress springs, remove components in the proper order, clean parts, and inspect for wear. Valves, guides, seals and other components are then reinstalled in the reverse order, taking care to lubricate parts and set components to the correct specifications.
Caterpillar cat 311 d lrr excavator (prefix cla) service repair manual (cla00...fjsekdmmeed
This document provides instructions for removing and installing inlet and exhaust valves, valve guides, and the engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to remove the cylinder head to access the valves. Procedures are provided for removing and installing the valves, guides, and oil cooler. Precautions are outlined to prevent contamination and contain fluids.
1. The document provides instructions for removing and installing inlet and exhaust valves and valve guides on a Caterpillar C4.2 engine.
2. The removal procedure includes using various tools to compress the valve springs, remove the valve keepers and other components, and extract the valves and valve guides.
3. The installation procedure specifies cleaning and lubricating the components, and using tools to reinstall the valve guides at the proper height and compress the springs to reinstall the valves and associated parts.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble and remove the components, cleaning requirements, and installation procedures.
The document provides instructions for removing and installing inlet and exhaust valves, valve guides, and an engine oil cooler on a Caterpillar C4.2 engine. It describes the required tools and steps to disassemble components like removing valve springs and stem seals, and installing new valve stem seals. Precautions are outlined to keep parts clean and contain fluids during the repair work.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...idkkdmmdd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not to replace reading the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...idkkmdmd
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It outlines the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve components. Reinstallation follows the reverse order, ensuring parts are clean and applying the proper pressure with the compressor tool. The summary is intended only to convey the main focus and steps involved, not serve as a replacement for the full instructions.
Caterpillar cat 323 d l excavator (prefix wgc) service repair manual (wgc0000...dhjfjkmmmde
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsjekkdkem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. The process is then reversed to install the new parts, ensuring the valve stem seal is installed correctly. Similar instructions are provided for removing and installing the valve guides.
Caterpillar cat 323 d excavator (prefix wgc) service repair manual (wgc00001 ...fhsejkdkmem
The document provides instructions for removing and installing inlet and exhaust valve springs on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves using a valve spring compressor tool to compress the valve spring and remove the retainer, spring, and valve keeper. Installation is the reverse process of cleaning components and lubricating the valve stem before reinstalling the valve keeper, spring, and retainer while compressing the spring with the tool.
Similar to Caterpillar cat 323 d l excavator (prefix gtf) service repair manual (gtf00001 and up) (17)
Kubota la1403 ec front loader service repair manualfjjskekdmmme
This document provides specifications and safety information for a Kubota front loader model LA1403EC. It includes:
1. Specifications for the loader model, bucket sizes, hydraulic system details, dimensions, and operational capacities.
2. Safety instructions for servicing the loader, including general precautions, safety starting and working procedures, avoiding fires, ventilation, acid burns, and emergency preparedness.
3. Terminology used to identify parts of the loader.
4. Tightening torques for screws, bolts, and hydraulic fittings on the loader.
5. Maintenance checklists and inspection procedures.
The document provides technical information and safety guidelines for servicing the Kub
Kubota la1403 front loader service repair manualfjjskekdmmme
This workshop manual provides information for servicing a Kubota LA1403 front loader. It is divided into three parts covering general information, the loader mechanism, and servicing procedures. The general section includes identification, safety, maintenance, and specifications. The mechanism section describes the construction and functions. The servicing section provides troubleshooting, repair, and assembly instructions.
Kubota kx121 2(h) excavator parts catalogue manualfjjskekdmmme
The document consists of the repeated text "classicmachinery.net" with no other substantive information. At the end, there is a brief note asking the reader to click a link for a complete manual, and to download a PDF first if there is no response to clicking the link.
John deere te gator utility vehicle service repair manualfjjskekdmmme
This technical manual provides information for servicing a Gator utility vehicle. It contains sections covering specifications, component locations, schematics, theory of operation, diagnostics, testing, repair and safety. Safety is the first section and provides instructions on battery safety, protective equipment, emergency procedures, charging batteries and acid burns. Technicians should follow all safety procedures when servicing this high voltage electrical system.
John deere pro gator 2030 utility vehicle service repair manualfjjskekdmmme
This document provides specifications for a John Deere ProGator 2030 Utility Vehicle. It includes specifications for the diesel engine, electrical system, fuel system, drive train, hydraulic system, tires, dimensions, torque specifications for fasteners, diesel fuel requirements, lubricants, and coolants. The specifications are organized into labeled sections for easy reference to details on particular systems.
John deere jx75 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service the mowers.
John deere je75 21 inch walk-behind mower service repair manualfjjskekdmmme
The document is a technical manual for John Deere 21-Inch Walk-Behind Mower models. It provides an introduction and overview of the manual's contents and organization. The manual contains sections on general specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, and torque specifications to assist technicians in servicing the mower models. It emphasizes reading all instructions before attempting any repairs.
John deere ja65 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
John deere ja62 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions to service various systems of the mower.
John deere jx85 21 inch walk-behind mower service repair manualfjjskekdmmme
This technical manual provides specifications and information for John Deere 21-inch walk-behind mowers. It includes sections on general vehicle specifications, engine specifications, electrical specifications, fuel system specifications, transmission specifications, dimensions, torque specifications, lubricant specifications, and product identification locations. The manual is intended to be a reference for technicians and contains detailed technical data, diagrams, and instructions for servicing and repairing the mowers.
Hyundai 40 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structure, operation, inspection, troubleshooting, and repair of components within that system. Symbols are used to identify important safety information. Conversion tables are included to allow simple unit conversions.
Hyundai 35 ds 7e forklift truck service repair manualfjjskekdmmme
This document provides an overview and structure of a service manual for a machine. It contains 8 sections that cover general information, removal/installation procedures, power train, brake, steering, hydraulic, electrical, and mast systems. Each section is divided into groups that explain the structures, operations, inspections, troubleshooting, and maintenance procedures for the components in that system. Conversion tables are also provided at the end to allow simple conversions between different units of measurement.
Hyundai 35 bh 9 forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The major steps include:
1) Disassembling the steering unit by removing components like the end cover, gearwheel set, cardan shaft, distributor plate, check valve parts, sleeve, spool, and pressure relief valve parts.
2) Assembling the spool and sleeve with neutral position springs installed in slots. Bearing races and seals are also installed.
3) Lubricating O-rings and seals before installing them using special tools to push them into place in the housing.
4) Proper positioning and alignment of parts is important during assembly to ensure correct functioning of the steering unit.
Hyundai 33 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a gear pump and controlled by a main relief valve and solenoid valve to engage the appropriate clutch for forward or reverse operation.
Hyundai 33 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The disassembly process involves removing components like the end cover, gearwheel set, cardan shaft, distributor plate, spool, sleeve and seals. The pressure relief valve is also disassembled by removing the plug, seal washers, setting screw, spring and piston. The assembly process describes fitting components like the spool, sleeve, cross pin, bearings, O-rings and lip seal back into the steering unit housing using various tools. Special care and markings are required when assembling the neutral position springs in the spool and sleeve.
Hyundai 30 df forklift truck service repair manualfjjskekdmmme
The document describes the structure and operation of the power train system of an industrial vehicle, including:
1. The main components of the power train system including the engine, transmission, drive shaft, drive axle, and brakes.
2. The transmission uses a torque converter and includes a forward clutch, reverse clutch, and output gear to transfer power from the input shaft to the output shaft in forward and reverse modes.
3. Oil is pumped through the system by a charging pump in the torque converter and is filtered, cooled, and distributed to clutches by the transmission control valve to engage the appropriate clutch for the selected gear.
Hyundai 30 d 7e forklift truck service repair manualfjjskekdmmme
This document provides instructions for disassembling and assembling a steering unit. The main steps for disassembly are: removing the end cover and gearwheel set; taking out the cardan shaft and distributor plate; pressing out the spool, sleeve, bearing races and thrust bearing; and disassembling the pressure relief valve. The main steps for assembly are: assembling the spool and sleeve with neutral position springs; fitting the bearing races and cross pin; installing the O-rings and lip seal using assembly tools; and reassembling other components. Precautions and the correct assembly pattern are emphasized to ensure proper reassembly.
Caterpillar cat 323 d s excavator (prefix dkw) service repair manual (dkw0000...fjjskekdmmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 3066 engine. It describes using lifting tools to remove the flywheel housing which weighs approximately 65 lbs. The procedure includes cleaning the mating surfaces, installing a new gasket, and securing the housing with bolts. Tools are also used to remove the old oil seal and install a new seal and crankshaft wear sleeve. Reinstalling the flywheel and electric starting motor completes the installation process.
Caterpillar cat 323 d s excavator (prefix cyd) service repair manual (cyd0000...fjjskekdmmme
The document provides disassembly and assembly instructions for a final drive on an excavator model 323D LN. Key steps include:
1. Removing the final drive cover, carrier assembly, sun gears, ring gears, and other components.
2. Disassembling the carrier assemblies by removing planetary gears, shafts, and bearings.
3. Assembling begins with pressing bearings into the main housing and determining the correct shim thickness. Seals, pins and other components are then installed to reassemble the final drive.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06051426
Inlet and Exhaust Valves - Remove and Install
SMCS - 1105-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
C 5P-1720 Seal Pick 1
Start By:
a. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Note the location and orientation of all components for assembly purposes.
1. Clean the bottom face of the cylinder head. Check the depth of the valves below the face of
the cylinder head before the valve springs are removed. Refer to Specifications, "Cylinder
Head Valves" for the correct dimensions.
1/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 2. Place a temporary identification mark on the heads of the valves in order to identify the
correct position.
Illustration 1 g01376164
3. Use a suitable lifting device in order to position cylinder head (1) onto Tooling (A) with the
valve springs upward. The weight of cylinder head (1) is approximately 113 kg (250 lb).
Note: Ensure that cylinder head (1) is kept on a clean, soft surface in order to prevent
damage to the machined face.
Illustration 2 g01376174
2/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01376184
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
4. Install Tooling (B) on cylinder head (1) in order to compress valve spring (5).
NOTICE
Ensure that the valve spring is compressed squarely or damage to the
valve stem may occur.
5. Apply sufficient pressure to Tooling (B) in order to remove valve keepers (3). Do not
compress the spring so that valve spring retainer (4) touches valve stem seal (6).
6. Slowly release the pressure on Tooling (B).
7. Remove valve spring retainer (4). Remove valve spring (5). Remove valve (2).
8. Use Tooling (C) in order to remove valve stem seal (6).
3/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 9. Repeat Steps 4 through 7 for the remaining valves.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 8S-6691 Cylinder Head Repair Stand 1
B 9U-6195 Valve Spring Compressor Gp 1
D 312-8755 Valve Stem Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean all components of the cylinder head assembly. Ensure that all ports, all coolant
passages, and all lubrication passages in the cylinder head are free from debris. Follow
Steps 1.a through 1.d in order to inspect the components of the cylinder head assembly.
Replace any components that are worn or damaged.
a. Inspect the cylinder head for wear and for damage. Refer to Testing and Adjusting,
"Cylinder Head Inspect".
b. Inspect the valve seats for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" for further information.
c. Inspect the valve guides for wear and for damage. Refer to Specifications, "Cylinder
Head Valves" and Testing and Adjusting, "Valve Guide - Inspect" for further
information.
d. Inspect the valves for wear and for damage. Refer to Specifications, "Cylinder Head
Valves ".
e. Inspect valve springs (5) for damage and for the correct length. Refer to
Specifications, "Cylinder Head Valves ".
4/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01376184
Illustration 5 g01376926
2. Lubricate the stem of valve (2) with clean engine oil. Install valve (2) in the appropriate
position in the cylinder head.
3. The outer face of the valve guides must be clean and dry before installing the valve stem
seal (6). Use Tooling (C) in order to install new valve stem seal (6) onto the valve guide.
4. Install valve spring (5) onto the cylinder head. Position valve spring retainer (4) on valve
spring (5).
5. Install Tooling (B) in the appropriate position on cylinder head (1) in order to compress
valve spring (5).
Improper assembly of parts that are spring loaded can cause bodily
injury.
5/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
6. Apply sufficient pressure to Tooling (B) in order to install valve keepers (3). Do not
compress spring (5) so that valve spring retainer (4) touches valve stem seal (6).
7. Carefully release the pressure on Tooling (B).
8. Repeat Steps 2 through 7 for the remaining valves.
End By:
a. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:04:42 UTC+0800 2020
6/6
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625003
Inlet and Exhaust Valve Guides - Remove and Install
SMCS - 1104-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 384-8861 Valve Guide Remover 1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 2 g01377121
2. Use Tooling (A) in order to remove valve guides (2) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8862 Valve Guide Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 3 g01377130
1. Lubricate the outside of valve guides (2) (not shown) with clean engine oil.
2. Use Tooling (E) in order to install new valve guides (2) . Install valve guide (2) so that
valve guide (2) protrudes 16.000 mm (0.6299 inch) above Surface (X) of cylinder head (1) .
End By:
a. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injector - Install".
b. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:05:41 UTC+0800 2020
4/4
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i04625001
Inlet and Exhaust Valve Seat Inserts - Remove and Install
SMCS - 1103-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
166-7441 Valve Seat Extractor Tool 1
6V-4194 Valve Seat Extractor (1)
1
6V-4196 Valve Seat Extractor (1)
1
B 138-7573 Link Bracket 4
C 1U-9200 Lever Puller Hoist 1
D 8S-6691 Cylinder Head Repair Stand 1
( 1 )
Component of the Valve Seat Extractor Tool Group.
Start By:
A. Remove the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and
Exhaust Valves - Remove and Install".
B. Remove the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Remove".
NOTICE
Keep all parts clean from contaminants.
1/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Contaminants may cause rapid wear and shortened component life.
Note: Refer to Special Instructions, SMHS7953-00, "Use of Valve Seat Insert Puller Group" to
aid with the removal of the inlet and exhaust valve seats.
Illustration 1 g01377064
1. Attach Tooling (B ) , Tooling (C) , and a suitable lifting device to cylinder head (1) . Use
Tooling (B ) , Tooling (C) , and the suitable lifting device in order to turn over cylinder head
(1) by 180° onto Tooling (D) .
2/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01376571
2. Use the valve seat grinder of Tooling (A) in order to notch the valve seat.
Illustration 3 g01376578
3. Use the valve seat extractor of Tooling (A) to remove the inlet and exhaust valve seats.
4. Clean the valve seat in the cylinder head. Remove any rough areas from the valve seat in the
cylinder head.
5. Repeat Steps 2 through 4 for the remaining inlet valve seat inserts and exhaust valve seat
inserts.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
E 384-8859 Valve Seat Installer 1
F 384-8860 Valve Seat Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 4 g01377071
Typical Example
1. Lower the temperature of the new inlet valve seat inserts (2) . Use Tooling (E) in order to
install a new inlet valve seat insert (2) (not shown) in the cylinder head.
Illustration 5 g01376588
Typical Example
2. Lower the temperature of new exhaust valve seat inserts (3) . Use Tooling (E) and Tooling
(F) in order to install the new exhaust valve seat insert (3) (not shown) in the cylinder head.
Note: The temperature of exhaust valve seat insert (3) is lowered in order to ease the
installation of exhaust valve seat insert (3) .
3. Repeat Step 1 and 2 for the remaining inlet valve seat inserts and exhaust valve seat inserts.
End By:
a. Install the inlet and exhaust valves. Refer to Disassembly and Assembly, "Inlet and Exhaust
Valves - Remove and Install".
b. Install the electronic unit injectors. Refer to Disassembly and Assembly, "Electronic Unit
Injectors - Install".
4/5
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746253
Engine Oil Cooler - Remove
SMCS - 1378-011
Removal Procedure
Start By:
a. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g01375410
1. Disconnect harness assembly (1).
2. Remove bolts (2) and remove engine oil cooler (3). Remove gasket (4) (not shown) from the
engine cylinder block.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:07:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746254
Engine Oil Cooler - Disassemble
SMCS - 1378-015
Disassembly Procedure
Start By:
a. Remove the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior of the
components should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism. Precision components can be damaged by contaminants or by dirt. Perform disassembly
procedures on a clean work surface. Keep components covered and protected at all times.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g01375411
1. Remove bolts (9) and the washers. Remove cover (8) and gasket (7).
2. Remove nuts (5) and the washers from engine oil cooler cover (4). Remove nuts (6) and the washers
from engine oil cooler cover (4).
3. Remove engine oil cooler core (2) from engine oil cooler cover (4). Remove gaskets (1) and (3).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:08:39 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746255
Engine Oil Cooler - Assemble
SMCS - 1378-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning fluid.
Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be deposited on the parts
which may cause trouble. Inspect all parts. If any parts are worn or damaged, use new parts for
replacement. Dirt and other contaminants can damage the precision component. Perform assembly
procedures on a clean work surface. Keep components covered and protected at all times.
Note: Check the gaskets for damage. Replace the components, if necessary.
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g01375411
1. Install gaskets (3) and (1) to engine oil cooler core (2). Position engine oil cooler core (2) to engine
oil cooler cover (4).
2. Install the washers and nuts (6). Install the washers and nuts (5).
3. Install gasket (7) and position cover (8). Install the washers and bolts (9).
End By:
a. Install the engine oil cooler. Refer to Disassembly and Assembly, "Engine Oil Cooler - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:09:38 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02746256
Engine Oil Cooler - Install
SMCS - 1378-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the gaskets for wear or for damage. Replace the components, if necessary.
Illustration 1 g01375410
1. Install gasket (4) (not shown). Position engine oil cooler (3) to the engine block. Install bolts
(2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 2. Connect harness assembly (1).
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:10:37 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751808
Engine Oil Relief Valve - Remove and Install
SMCS - 1315-010
Removal Procedure
Start By:
a. Remove the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377673
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 1. Remove engine oil relief valve (1).
2. Remove gasket (2) (not shown). Discard gasket (2).
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01377673
1. Install a new gasket (2) (not shown).
2. Install engine oil relief valve (1). Tighten engine oil relief valve (1) to a torque of
49 ± 5 N·m (36 ± 4 lb ft).
End By:
a. Install the electronic control module. Refer to Disassembly and Assembly, "Electronic
Control Module - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Aug 21 22:11:36 UTC+0800 2020
2/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 323D L EXCAVATOR GTF
Configuration: 323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02751881
Engine Oil Bypass Valve - Remove and Install
SMCS - 1306-010-BV
Removal Procedure
Start By:
a. Remove the oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g01377713
1. Remove engine oil bypass valve (1). Remove gasket (2) (not shown). Discard gasket (2).
1/2
323D L Excavator GTF00001-UP (MACHINE) POWERED BY C6.4 Engine(SEBP56...
2020/8/21
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...