This document provides instructions for installing an idler gear on a C4.4 engine. It outlines 19 steps including cleaning and inspecting parts, installing locking pins to hold components in place, lubricating and installing the idler gear and hub, checking timing marks and backlash, and reinstalling covers once complete. Tools required include various pins, sockets, and indicators to aid in the installation and ensure proper timing. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820291
Idler Gear - Install
SMCS - 1206-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A(1)
9U-6198 Crankshaft Turning Tool 1
A(2)
5P-7306 Housing 1
5P-7305 Engine Turning Tool 1
B 364-9107
Timing Pin
(Fuel Injection Pump)
1
C 230-6284
Timing Pin
(Camshaft)
1
D
136-4632
Timing Pin
(Crankshaft)
1
268-1966 Adapter 1
E 298-5564 T40 Torx Socket 1
F
9U-7324 Indicator Bracket 1
7H-1942 Dial Indicator 1
3S-3268 Indicator Contact Point 1
7H-1940 Universal Attachment 1
(1)
The Crankshaft Turning Tool is used on the front pulley.
1/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. (2)
This Tool is used in the aperture for the electric starting motor.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Ensure that number one piston is at top dead center on the compression stroke. Refer to
System Operation, Testing and Adjusting, "Finding Top Center for No. 1 Piston" for the
correct procedure.
Illustration 1 g02491276
2/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g01996475
2. Ensure that Tooling (D) is installed in Hole (W) in the cylinder block. Use Tooling (D) in
order to lock the crankshaft in the correct Position. Refer to System Operation, Testing and
Adjusting, "Finding Top Center Position for No.1 Piston" for the correct procedure.
3. Ensure that Tooling (C) is installed into Hole (X) in camshaft gear (3).
4. Use Tooling (B) in order to lock the fuel injection pump gear in the correct position. Refer
to Disassembly and Assembly, "Fuel Injection Pump - Remove" for the correct procedure.
3/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 3 g01996477
4/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 4 g01996478
5/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 5 g01996576
5. Clean idler gear (4) and inspect the idler gear for wear and damage. Refer to Specifications,
"Gear Group (Front)" for more information. If necessary, replace the idler gear.
6. Clean hub (9) and inspect the hub for wear and damage. Refer to Specifications, "Gear
Group (Front)" for more information. If necessary, replace the hub.
7. Lubricate hub (9) with clean engine oil. Install hub (9) into the recess in the front housing.
Ensure that oil Hole (Z) is to the top of the hub.
8. Install idler gear (4) onto hub (9). Ensure that the timing marks are toward the front of the
idler gear.
9. Align the timing mark on idler gear (4) with the timing mark on camshaft gear (3), fuel
injection pump gear (10) and crankshaft gear (11). Refer to the Illustration 5. Install the
assembly of idler gear (4) to hub (9).
10. Clean plate (8) and inspect the plate for wear and damage. If necessary, replace the plate.
11. Lubricate plate (8) with clean engine oil. Align the holes in plate (8) with the holes in hub
(9). Install the plate in the original orientation.
Note: Ensure that the identification mark TOP is upward.
12. Install bolts (7). Tighten the bolts to a torque of 44 N·m (32 lb ft).
13. Remove Tooling (B), Tooling (C), and Tooling (D).
6/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Note: Ensure that timing marks are aligned, before removing the Tooling (B), Tooling (C),
and Tooling (D).
14. Use Tooling (F) in order to check the end play for the idler gear. Refer to Specifications,
"Gear Group (Front)" for more information.
15. Use Tooling (F) in order to check the backlash between the idler gear and the camshaft gear.
Refer to Specifications, "Gear Group (Front)" for more information.
16. Use Tooling (F) in order to check the backlash between the idler gear and the crankshaft
gear. Refer to Specifications, "Gear Group (Front)" for more information.
17. Use Tooling (F) in order to check the backlash between the idler gear and the fuel injection
pump gear. Refer to Specifications, "Gear Group (Front)" for more information.
18. Lightly lubricate all of the gears with clean engine oil.
NOTICE
Failure to ensure that the crankshaft is set in the safe position will
result in interference between the pistons and the valves. Interference
between the pistons and the valves will result in damage to the engine.
19. Use Tooling (A) in order to rotate the crankshaft in a clockwise direction and position the
crankshaft at the safe position. Refer to System Operation, Testing and Adjusting, "Position
the Valve Mechanism Before Maintenance Procedures" for the correct procedure.
7/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 6 g01994556
20. Ensure that the guides for the pushrods are correctly positioned on the threaded inserts (5).
Use Tooling (E) in order to tighten threaded inserts (5) on all rocker arms (6). Tighten the
threaded inserts to a torque of 30 N·m (265 lb in).
Note: When the threaded insert is tightened, the threaded insert must be seated correctly
into the cup for the pushrod.
21. The engine should not be operated for a period 45 minutes after the threaded inserts on all
the rocker arms have been tightened. This period will allow the force of the valve springs to
purge off excessive engine oil from the hydraulic lifters.
8/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 7 g02485936
22. Position a new O-ring seal (2) onto plug (1). Install the plug to the cylinder block and
tighten the plug to a torque of 21 N·m (186 lb in).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove and
Install" for the correct procedure.
b. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install" for the correct procedure.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:56:27 UTC+0800 2020
9/9313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820292
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02488340
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02488341
6. Remove bolts (10), bolts (11) and bolts (12) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the different bolts.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (13).
3/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g02488356
9. Remove thrust washer (14) from cylinder block (15).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:57:24 UTC+0800 2020
4/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820293
Housing (Front) - Remove - Heavy Duty Housing (Front)
SMCS - 1151-011
Removal Procedure
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install" for the
correct procedure.
b. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove" for the correct procedure.
c. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove" for the correct procedure.
d. If the engine has an accessory drive, remove the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
e. Remove the water pump. Refer to Disassembly and Assembly, "Water Pump - Remove" for
the correct procedure.
f. Remove the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) -
Remove and Install" for the correct procedure.
g. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g02490356
1. Slide locking tab (1) (not shown) into the unlocked position.
2. Disconnect harness assembly (2) from coolant temperature sensor (3).
3. Cut cable strap (4) and remove harness assembly (2) from bypass tube (5).
4. Remove bolts (6) that secure bypass tube (5) to front housing (7).
2/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. 5. Remove bypass tube (5) from the cylinder head. Remove O-ring seal (8) and O-ring seal (9)
from bypass tube (5).
Illustration 2 g02490357
6. Remove bolts (11), bolts (12) and bolts (13) from front housing (7).
Note: The bolts are three different lengths. Note the positions of the bolts of different
length.
7. Remove front housing (7) from the cylinder block.
8. Remove gasket (14).
9. If necessary, follow Step 9.a through Step 9.b in order to remove bearing (10) from housing
(7).
a. Place housing (7) onto a suitable support.
b. Use a suitable tool in order to press bearing (10) out of housing (7).
3/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g02490358
10. Remove thrust washer (15) from cylinder block (16).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Thu Jun 11 17:58:21 UTC+0800 2020
4/4313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 313F EXCAVATOR NLG
Configuration: 313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
C4.4 Engines for Caterpillar Built Machines
Media Number -UENR4516-11 Publication Date -01/06/2015 Date Updated -29/10/2018
i05820294
Housing (Front) - Install - Heavy Duty Housing (Front)
SMCS - 1151-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6640 Sealant 1
B -
Guide Studs
M8 by 80 mm
2
C
319-6486 Alignment Tool 1
-
Bolts
M10 by 50 mm
3
D 1U-6396 O-Ring Assembly Compound 1
E 7M-7456 Bearing Mount Compound 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Ensure that the wiring harness assembly is correctly routed and the
cable straps are not over tightened. Over tightening of the cable straps
will damage the wiring harness and the convoluting.
1. Ensure that the front housing is clean and free from damage. If necessary, replace the front
housing.
If necessary, install blanking plugs to a new front housing. Use Tooling (A) in order to seal
all D-plugs.
2. Clean all the gasket surfaces of the cylinder block.
Illustration 1 g02490396
2/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g02490397
3. Inspect dowel (17) and dowel (18) for damage. If necessary, replace the dowels in the
cylinder block.
4. Install thrust washer (15) into the recess in cylinder block (16). Refer to Disassembly and
Assembly, "Camshaft - Install" for more information.
5. Install Tooling (B) to cylinder block (16). Refer to Illustration 2.
6. Align a new gasket (10) with Tooling (B). Install the gasket to (16) cylinder block.
Note: Ensure that two circular Tabs (X) on the gasket are engaged in two Holes (Y) in
cylinder block (16). Ensure that dowel (18) in cylinder block (16) is engaged on the gasket.
7. Install Tooling (C) to cylinder block (16).
3/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 3 g02490399
8. If necessary, follow Step 8.a through Step 8.c in order to install bearing (10) to housing (7).
a. Apply a small continuous bead of Tooling (E) to outer Surface (Z) of bearing (10).
b. Place housing (7) onto a suitable support.
c. Use a suitable tool in order to press bearing (10) into housing (7) until the bearing is
in the correct position within the housing. Remove any excess bearing mount
compound.
9. Install the front housing over Tooling (B) and Tooling (C) onto cylinder block (16).
4/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 4 g02490400
(11) M8 by 35 mm
(12) M8 by 20 mm
(13) M8 by 25 mm
5/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 5 g02058297
10. Install bolts (13) to front housing (7) finger tight.
11. Remove Tooling (B).
12. Loosely install bolts (11) and bolts (12). Refer to Illustration 4 for the correct position of the
bolts.
13. Tighten bolts (11), bolts (12) and bolts (13) in the sequence that is shown in Illustration 5 to
a torque of 28 N·m (248 lb in).
14. Remove Tooling (C) from the cylinder block.
6/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 6 g02490356
15. Install a new O-ring seal (8) and a new O-ring seal (9) to bypass tube (5). Use Tooling (D)
in order to lubricate the O-ring seals.
16. Install bypass tube (5) to the cylinder head. Install bolts (6). Tighten the bolts to a torque of
9 N·m (80 lb in).
17. Connect harness assembly (2) to coolant temperature sensor (3).
18. Slide locking tab (1) (not shown) into the locked position.
19. Position harness assembly (2) onto bypass tube (5). Install a new cable strap (4).
Note: Ensure that the cable strap meets Original Equipment Manufactures (OEM)
specification.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install" for the correct procedure.
b. Install the timing gears. Refer to Disassembly and Assembly, "Gear Group (Front) - Install"
for the correct procedure.
c. If the engine has an accessory drive, install the accessory drive. Refer to Disassembly and
Assembly, "Accessory Drive - Remove and Install" for the correct procedure.
7/8313F & 313F L Excavators NLG00001-UP (MACHINE) POWERED BY C4.4 Engine...
2020/6/11https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...