In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 22:57:58 UTC+0800 2020
3/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 22:58:54 UTC+0800 2020
3/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:00:45 UTC+0800 2020
3/3(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:01:41 UTC+0800 2020
4/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:02:37 UTC+0800 2020
4/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:03:32 UTC+0800 2020
2/2(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Oct 28 23:04:28 UTC+0800 2020
2/2(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D RR EXCAVATOR GMX
Configuration: 320D RR & 320D LRR Excavators GMX00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
26. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
27. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
28. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4(W)
w
2020/10/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...