The document provides instructions for removing and installing the flywheel on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel bolts and housing, then lifting the flywheel off. Reinstallation involves cleaning surfaces, installing with bolts and checking runout. Removing the rear crankshaft seal and installing a new one is also described.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...yu5676962
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...ze6074xunong
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...f8seodkdmdmed3
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...gongfuao7509
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...f8usejkdmmd8i
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove the flywheel, flywheel housing, rear crankshaft seal, and installing replacements. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing the flywheel and flywheel housing on a Caterpillar 320D LRR excavator with a C6.4 engine. It describes using various tools to remove components like the flywheel, flywheel ring gear, flywheel housing seal, and installing replacement parts. The document contains diagrams to illustrate the procedures.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...yu5676962
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...ze6074xunong
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...f8seodkdmdmed3
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...gongfuao7509
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...f8usejkdmmd8i
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...9fiseookddk
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...8foskkdjdkdm3e
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document contains detailed step-by-step instructions, illustrations, and safety notices for working on and servicing parts of the Caterpillar C6.4 engine.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document contains detailed step-by-step instructions, illustrations, and safety notices for working on and servicing parts of the Caterpillar C6.4 engine.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists any required tools. Safety notices are also provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the specific section of the document for full instructions.
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove bolts securing the housing. The housing weighs approximately 29 kg and is removed along with the gasket. A driver group tool is used to remove the oil seal from the housing. Reinstallation involves installing a new gasket and oil seal then securing the housing with bolts and washers.
Caterpillar cat 320 d rr excavator (prefix gmx) service repair manual (gmx000...fjkskedmme
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjskefksemer
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 320 d l excavator (prefix phx) service repair manual (phx0000...fjjkefkksem
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using tooling and lifting devices to remove the flywheel and install a replacement. Specific steps include removing mounting bolts and brackets, drilling holes in the rear crankshaft seal before removing it, and checking that the flywheel housing dowels are not damaged during removal and installation. Torques and tools required are listed in tables at the start.
Caterpillar cat 320 d excavator (prefix phx) service repair manual (phx00001 ...fjjsekfksmem
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using tooling and lifting devices to remove the flywheel and install a replacement. Specific steps include removing mounting bolts and brackets, drilling holes in the rear crankshaft seal before removing it, and checking that the flywheel housing dowels are not damaged during removal and installation. Torques and tools required are listed in tables at the start.
Caterpillar cat 320 d l excavator (prefix phx) service repair manual (phx0000...jfjskeksemmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. Key steps include:
1. Removing the electric starting motor and flywheel before removing the flywheel housing.
2. Installing a lifting device and link bracket to the flywheel housing and removing bolts and washers to separate it from the cylinder block.
3. Using a driver group to remove the oil seal from the housing.
4. Cleaning and applying compound to mating surfaces before installing a new oil seal and reattaching the flywheel housing with bolts and washers.
Caterpillar cat 320 d excavator (prefix phx) service repair manual (phx00001 ...fujsjekskem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. Key steps include:
1. Removing the electric starting motor and flywheel before removing the flywheel housing.
2. Installing lifting tools and removing bolts to lift the flywheel housing off the cylinder block.
3. Using drivers to remove the oil seal from the housing.
Installation is the reverse of removal, including installing a new gasket and oil seal before securing the housing with bolts.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove the flywheel housing, flywheel, crankshaft rear seal, and crankshaft pulley. The installation process specifies cleaning and applying compounds to parts and using installing tools to replace components like the rear seal and ensure correct installation. Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...f8seodkdmdmed3
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove the flywheel housing, flywheel, crankshaft rear seal, and crankshaft pulley. The installation process specifies cleaning and applying compounds to parts and reinstalling them in reverse order using installing tools like the link bracket and driver group. Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...yu5676962
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove components like the flywheel, flywheel housing, and crankshaft pulley. The installation process specifies cleaning and applying compounds to mating surfaces, and torquing bolts to the specified values. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
More Related Content
Similar to Caterpillar Cat 320D LRR Excavator (Prefix EJT) Service Repair Manual (EJT00001 and up).pdf
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...9fiseookddk
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar Cat 320D RR and 320D LRR Excavator (Prefix GMX) Service Repair Ma...8foskkdjdkdm3e
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document contains detailed step-by-step instructions, illustrations, and safety notices for working on and servicing parts of the Caterpillar C6.4 engine.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists the required tools. Safety notices are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document contains detailed step-by-step instructions, illustrations, and safety notices for working on and servicing parts of the Caterpillar C6.4 engine.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The document gives detailed step-by-step instructions and illustrations for each procedure, and lists any required tools. Safety notices are also provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the specific section of the document for full instructions.
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor and flywheel first. Then a lifting device and link bracket are used to remove bolts securing the housing. The housing weighs approximately 29 kg and is removed along with the gasket. A driver group tool is used to remove the oil seal from the housing. Reinstallation involves installing a new gasket and oil seal then securing the housing with bolts and washers.
Caterpillar cat 320 d rr excavator (prefix gmx) service repair manual (gmx000...fjkskedmme
The document provides instructions for removing and installing a flywheel housing on a 320D RR excavator. It describes removing the electric starting motor, flywheel, bolts and washers securing the housing. It also includes removing the gasket and oil seal from the housing. For installation, it specifies cleaning and applying retaining compound before installing a new oil seal and reattaching the housing with bolts and washers.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjkskedmme
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 320 d lrr excavator (prefix gmx) service repair manual (gmx00...fjskefksemer
This document provides instructions for removing and installing various engine components on a Caterpillar 320D RR excavator, including:
- Removing and installing the flywheel using various tools
- Removing and installing the crankshaft rear seal
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The summaries provide an overview of the component being worked on and refer the user to the detailed instructions and illustrations in the document.
Caterpillar cat 320 d l excavator (prefix phx) service repair manual (phx0000...fjjkefkksem
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using tooling and lifting devices to remove the flywheel and install a replacement. Specific steps include removing mounting bolts and brackets, drilling holes in the rear crankshaft seal before removing it, and checking that the flywheel housing dowels are not damaged during removal and installation. Torques and tools required are listed in tables at the start.
Caterpillar cat 320 d excavator (prefix phx) service repair manual (phx00001 ...fjjsekfksmem
The document provides instructions for removing and installing a flywheel on a Caterpillar 320D L excavator. It describes using tooling and lifting devices to remove the flywheel and install a replacement. Specific steps include removing mounting bolts and brackets, drilling holes in the rear crankshaft seal before removing it, and checking that the flywheel housing dowels are not damaged during removal and installation. Torques and tools required are listed in tables at the start.
Caterpillar cat 320 d l excavator (prefix phx) service repair manual (phx0000...jfjskeksemmme
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. Key steps include:
1. Removing the electric starting motor and flywheel before removing the flywheel housing.
2. Installing a lifting device and link bracket to the flywheel housing and removing bolts and washers to separate it from the cylinder block.
3. Using a driver group to remove the oil seal from the housing.
4. Cleaning and applying compound to mating surfaces before installing a new oil seal and reattaching the flywheel housing with bolts and washers.
Caterpillar cat 320 d excavator (prefix phx) service repair manual (phx00001 ...fujsjekskem
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. Key steps include:
1. Removing the electric starting motor and flywheel before removing the flywheel housing.
2. Installing lifting tools and removing bolts to lift the flywheel housing off the cylinder block.
3. Using drivers to remove the oil seal from the housing.
Installation is the reverse of removal, including installing a new gasket and oil seal before securing the housing with bolts.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...gongfuao7509
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove the flywheel housing, flywheel, crankshaft rear seal, and crankshaft pulley. The installation process specifies cleaning and applying compounds to parts and using installing tools to replace components like the rear seal and ensure correct installation. Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a Caterpillar 320D L excavator. The removal procedure involves using a link bracket and lifting device to remove the flywheel housing after removing bolts and washers. A driver group is then used to remove the oil seal from the housing. The installation procedure is not described.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...f8seodkdmdmed3
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove the flywheel housing, flywheel, crankshaft rear seal, and crankshaft pulley. The installation process specifies cleaning and applying compounds to parts and reinstalling them in reverse order using installing tools like the link bracket and driver group. Precautions are provided to keep parts clean and contain fluids.
Caterpillar Cat 320D and 320D L Excavator (Prefix PHX) Service Repair Manual ...yu5676962
This document provides instructions for removing and installing the flywheel and crankshaft pulley on a Caterpillar C6.4 engine. The removal process involves using tools like a link bracket and driver group to remove components like the flywheel, flywheel housing, and crankshaft pulley. The installation process specifies cleaning and applying compounds to mating surfaces, and torquing bolts to the specified values. Proper cleaning and installation of gaskets and seals is emphasized to prevent leaks.
Similar to Caterpillar Cat 320D LRR Excavator (Prefix EJT) Service Repair Manual (EJT00001 and up).pdf (20)
This document provides instructions for servicing components of a Caterpillar 330D L excavator engine. It describes procedures for removing and installing the cylinder head, camshaft, lifter group, and associated parts. The steps include draining coolant, removing mounting hardware, lifting components with tools, applying lubricant, and torquing fasteners to specified values. Safety notices are provided to keep parts clean and prevent damage during removal and installation.
1. The document provides instructions for assembling and installing the swing drive of an excavator model 330D L.
2. It describes 30 steps for assembling bearings, gears, shafts, seals, and housings and attaching the assembly to the excavator frame using bolts.
3. Proper cleaning, lubrication, and heating of parts is emphasized to ensure correct assembly. Tools, torque specifications, and maintenance procedures are also outlined.
Caterpillar Cat 330C L Excavator (Prefix MCA) Service Repair Manual (MCA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The disassembly process involves removing 28 different components in a specific sequence. The assembly process reverses the disassembly steps and includes applying thread lock compound and lubricating components before reassembly. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 330C L Excavator (Prefix KDD) Service Repair Manual (KDD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling a 330C excavator travel motor. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, cam plate, and rotating assembly into the housing. Special tools are listed and safety notices are provided throughout regarding cleaning, pressurized air, and spring loading.
Caterpillar Cat 330C L Excavator (Prefix JNK) Service Repair Manual (JNK00001...fjkdksmmdm
The document provides instructions for assembling and installing a piston motor (hydraulic fan). It is a 3 page document that details 20 steps for assembly, including installing various components like bearings, seals, springs and retaining rings. It then provides 11 steps for installing the assembled piston motor and attaching hoses and guards. Proper cleaning and lubrication of parts is emphasized.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B1K) Service Repair Manual (B1K0000...fjkdksmmdm
This document provides instructions for installing a camshaft on a Caterpillar 330C FM excavator engine. It begins by listing the required tools. The instructions then state to clean all parts, set the number 1 piston to top center, and align the camshaft and idler gears. The camshaft is then lubricated and inserted into the cylinder block. The thrust plate and bolts are installed and tightened. Lifters are repositioned and the procedure ends by installing the front cover and rocker arm assembly.
Caterpillar Cat 330C L Excavator (Prefix JCD) Service Repair Manual (JCD00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavators. It outlines 28 steps for disassembly, removing components like the head, springs, brake piston, and bearings. It then outlines 13 steps for assembly, replacing seals and installing components in the reverse order of disassembly, taking care to mark parts and return them to their original positions. Special tools are listed that may be required for tasks like removing races and seals.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and seals. It then describes 15 steps for reassembling the motor and installing components in the reverse order, making sure to clean parts and apply thread lock compound as needed. Tools required include retaining ring pliers, a bearing puller, an eyebolt, and an adapter.
Caterpillar Cat 330C L Excavator (Prefix GKX) Service Repair Manual (GKX00001...fjkdksmmdm
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
Caterpillar Cat 330C L Excavator (Prefix DKY) Service Repair Manual (DKY00001...fjkdksmmdm
- The document provides disassembly and assembly instructions for the travel motor of a 330C L excavator.
- It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, and bearing races.
- It then describes 28 steps for assembling the travel motor, providing notes on cleaning, applying sealant, and ensuring proper alignment of components like the cam plate and keys.
- Tools required include retaining ring pliers, a bearing puller, threaded rod, and eyebolt for installation and removal of components.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. It describes 28 steps to disassemble the motor by removing components like the head, port plate, springs, brake piston, plates, and bearings. It then describes 13 steps for assembly, including installing seals, bearings, springs, and securing the rotating assembly back into the housing. Special tools are listed and safety notices are provided throughout regarding handling pressurized components and ensuring cleanliness during reassembly.
Caterpillar Cat 330C L Excavator (Prefix CYA) Service Repair Manual (CYA00001...fjkdksmmdm
This document provides instructions for disassembling and assembling the travel motor on a 330C L excavator. The disassembly process involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals. The assembly process reverses the disassembly steps and includes installing seals, bearings, and retaining rings in their proper positions. Cleanliness is important during assembly to prevent contamination.
Caterpillar Cat 330C FM EXCAVATOR (Prefix B3M) Service Repair Manual (B3M0000...fjkdksmmdm
This document provides instructions for releasing hydraulic pressure from the systems of a 330C FM excavator before performing service. It describes:
- Releasing pressure from a single circuit by moving the relevant control to its full stroke position with the engine on and activation lever unlocked.
- Releasing pressure from multiple circuits by repeating this process for each circuit needing service.
- Additional steps like starting the engine briefly with no control movement to further release pressure across systems.
The document aims to safely depressurize hydraulic lines and components before disconnection or removal during maintenance.
This document provides instructions for disassembling and assembling the travel motor on a 330C excavator. It describes 28 steps to disassemble the motor by removing components like the head, port plate, bearings, brake piston, plates, and seals. It then describes 13 steps for assembling the motor, replacing all seals and installing components in reverse order of removal. Special tools are required and cleanliness is important when handling parts.
This document provides instructions for disassembling and assembling the travel motor on 330C and 330C L excavator models. The summary is:
1. The travel motor disassembly procedure involves removing 28 components including the head, port plate, springs, brake piston, plates, and seals.
2. Travel motor assembly requires installing components in reverse order, applying thread lock compound and oil, and torquing bolts to specified values.
3. Special tools are required to remove races, seals, and retainers, and care must be taken to avoid damaging parts and ensure proper alignment of keys and plates.
This document provides instructions for assembling a piston motor (hydraulic fan) with 20 steps. It involves installing various components like bearing cups, seals, pins, springs, pistons, and plates in the proper sequence and orientation. Safety notes are included to handle parts carefully and apply oil during assembly. The summary is complete in 3 sentences.
1) The document provides disassembly and assembly instructions for a travel motor on 330C and 330C L excavator models.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, plates, seals, bearings, and housing covers.
3) It then lists 28 steps for reassembling the travel motor, replacing all seals and applying lubricant before reinstalling the components in reverse order of disassembly. Proper cleanliness and torque specifications are emphasized.
1) The document provides instructions for disassembling and assembling the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, port plate, springs, brake piston, plates, and seals.
3) It then lists 28 steps for reassembling the travel motor, placing components back in reverse order and noting alignment and torque specifications. Precise reassembly is emphasized for correct operation.
1) The document provides step-by-step instructions for disassembling and assembling the travel motor of 330C and 330C L excavator models.
2) It details 28 steps for disassembly, including removing the head, brake piston, plates and discs, seals, and other components. Special tools are required.
3) It then lists 28 steps for reassembly, providing notes on cleaning, lubrication, and proper installation of O-rings and other parts to ensure correct assembly. The keys and notches must be properly aligned and torques applied to specifications.
1) The document provides disassembly and assembly instructions for the travel motor of a 330C excavator.
2) It describes 28 steps to disassemble the travel motor by removing components like the head, springs, plates, and seals.
3) It then describes 29 steps for assembling the travel motor, including installing seals, plates, springs, and tightening bolts in the proper order and with specified torques.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02743771
Flywheel - Remove
SMCS - 1156-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B Forcing bolts M16 - 2 by 120 mm 2
Start By:
a. Remove the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
b. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
3. Illustration 1 g01374966
1. Remove muffler brackets (1).
Illustration 2 g01374968
Illustration 3 g01374970
2. Remove bolts (2).
3. Install Tooling (A) and a suitable lifting device onto flywheel (3).
4. Use Tooling (B) in order to remove flywheel (3) out of the housing. The weight of flywheel
(3) is approximately 50 kg (110 lb).
2/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
4. 5. Perform the following procedure in order to remove the flywheel ring gear.
Illustration 4 g01374977
Typical Example
a. Place flywheel (3) and ring gear (4) on suitable cribbing.
Note: Mark the orientation of ring gear (4) on flywheel (3) for assembly purposes.
Always wear protective gloves when handling parts that have been
heated.
b. Raise the temperature of ring gear (4) uniformly.
c. Remove the ring gear (4) by tapping ring gear (4) all the way around flywheel (3).
d. Reposition flywheel (3) in order to remove ring gear (4).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:47:36 UTC+0800 2020
3/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02744399
Flywheel - Install
SMCS - 1156-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Always wear protective gloves when handling parts that have been
heated.
1. Perform the following procedure, if the ring gear was removed from the flywheel:
a. Raise the temperature of the ring gear 149 °C (300 °F).
1/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
6. b. Use a suitable press in order to install the ring gear onto the flywheel.
Note: Prior to the installation of the flywheel, refer to Specifications, "Flywheel" for
information on checking the flywheel assembly for flatness.
Illustration 1 g01374993
2. Install Tooling (A) and a suitable lifting device onto flywheel (3).
3. Install flywheel (3). The weight of flywheel (3) is approximately 50 kg (110 lb).
Illustration 2 g01374968
4. Install bolts (2) in order to secure flywheel (3) onto the crankshaft. Tighten bolts (2) to a
torque of 83 ± 5 N·m (61 ± 4 lb ft).
5. Remove Tooling (A) from flywheel (3).
2/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
7. Illustration 3 g01374966
6. Install muffler brackets (1).
7. Check the flywheel runout. Refer to Testing and Adjusting, "Flywheel Housing - Inspect"
for more information on flywheel runout.
End By:
a. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
b. Install the crankshaft position sensor. Refer to Disassembly and Assembly, "Crankshaft
Position Sensor - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:48:31 UTC+0800 2020
3/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01135944
Crankshaft Rear Seal - Remove
SMCS - 1161-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B
5P-7312 Seal Distorter 1
5P-7338 Distorter Ring 2
Start By:
a. Remove the flywheel. Refer to Disassembly and Assembly, "Flywheel - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
1/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
9. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00604840
Note: If the oil seal shows a sign of oil leaks, remove the wear sleeve and the oil seal.
1. Drill three evenly spaced 3 mm (0.12 inch) holes in crankshaft rear seal (1).
2. Use Tool (A) to remove the crankshaft rear seal.
Illustration 2 g00604844
3. Use Tool (B) to remove the wear sleeve (2) (not shown) from the rear of the crankshaft.
Note: When you are removing the wear sleeve, take extreme care not to damage the
crankshaft.
2/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i01615317
Crankshaft Rear Seal - Install
SMCS - 1161-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
9U-6169 Installer 1
9U-6171 Locator 1
9U-6172 Bolt 2
5P-8247 Hard Washer 1
6V-3303 Bolt 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. To install a new wear sleeve that is complete with a seal, use 169-5464 Quick Cure Primer
to clean the outer diameter of the crankshaft and the inside diameter of the wear sleeve.
Apply 4C-9507 Retaining Compound to the faces of all the mating parts.
1/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
11. Illustration 1 g00604874
2. Install a new wear sleeve that is complete with a seal (1) (not shown) with Tool (A), as
follows:
Illustration 2 g00604875
a. Install 9U-6171 Locator (3) onto the crankshaft with 9U-6172 Bolt (4).
b. Put the new wear sleeve that is complete with a seal in 9U-6169 Installer (2).
c. Put 6V-3303 Bolt (6) through 5P-8247 Hard Washer (5) and 9U-6169 Installer (2)
and thread into 9U-6171 Locator (3).
d. Push the wear sleeve that is complete with a seal onto the crankshaft until 9U-6169
Installer (2) bottoms out.
2/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
12. Illustration 3 g00604874
e. Remove Tool (A) and check crankshaft rear seal (1) (not shown) for correct
installation.
End By:
a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:50:23 UTC+0800 2020
3/3(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742697
Flywheel Housing - Remove and Install
SMCS - 1157-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
b. Remove the flywheel and ring gear. Refer to Disassembly and Assembly, "Flywheel -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
14. Illustration 1 g01374571
1. Install Tooling (A), and a suitable lifting device onto flywheel housing (3).
2. Remove bolts (2) and the washers that secure flywheel housing (3) to the cylinder block.
3. Remove flywheel housing (3). The weight of flywheel (3) is approximately 29 kg (65 lb).
4. Remove gasket (1) (not shown).
Illustration 2 g01374572
5. Use Tooling (B) in order to remove the oil seal (4) (not shown).
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 1
B 1P-0510 Driver Group 1
NOTICE
2/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
15. Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g01374614
1. Use Tooling (B) in order to install the oil seal (4) (not shown).
Illustration 4 g01374571
2. Check the condition of two dowels (not shown). If dowels are damaged, use new parts for
replacement.
3. Clean old gasket (1) (not shown) from the mating surfaces of the cylinder block and the
flywheel housing. Install a new gasket on the cylinder block.
4. Place flywheel housing (3) in position on the cylinder block.
5. Install the washers and bolts (2) in order to secure flywheel housing (3) to the cylinder
block.
6. Remove Tooling (A).
End By:
3/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
16. a. Install the flywheel. Refer to Disassembly and Assembly, "Flywheel - Install".
b. Install the electric starting motor. Refer to Disassembly and Assembly, "Electric Starting
Motor- Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:51:19 UTC+0800 2020
4/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i06790404
Crankshaft Pulley - Remove and Install
SMCS - 1205-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2321 Combination Puller 1
B 6V-9120 Socket(1)
1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Remove the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
1/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
18. Illustration 1 g00604778
2. Use Tooling (B) in order to remove nut (1) and washer (2) from the threaded end of the
crankshaft.
Illustration 2 g00604784
3. Use Tooling (A) in order to remove crankshaft pulley (3) from the engine.
2/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
19. Illustration 3 g00604792
4. If it is necessary to remove wear sleeve (4) from crankshaft pulley (3), use a suitable
hammer and a suitable chisel. Hold the suitable chisel at right angles to the surface of the
wear sleeve. Tap the wear sleeve in three places. You can remove the wear sleeve once the
tension is released.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
B 6V-9120 Socket(1)
1
C 1P-0510 Driver Gp 1
(1)
Tooling (B) is a 46 mm socket.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Raise the temperature of the wear sleeve. Use Tooling (C) in order to install the wear sleeve
onto the crankshaft pulley.
3/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
20. Illustration 4 g01377941
2. Ensure that baffle plate (5) is oriented, as shown.
Illustration 5 g00604778
3. Position crankshaft pulley (3) onto the engine.
4. Install washer (2) and nut (1). Use Tooling (B) in order to tighten nut (1) to a torque of
707.5 ± 57.5 N·m (522 ± 42 lb ft).
5. Install the belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:52:14 UTC+0800 2020
4/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742689
Crankshaft Front Seal - Remove
SMCS - 1160-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
Start By:
a. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/2(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
22. Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00529162
Typical Example
1. Drill three evenly spaced 3.0 mm (0.12 inch) holes in crankshaft front seal (1).
2. Use Tooling (A) in order to remove crankshaft front seal (1). Remove the seal evenly by
alternating the position of Tooling (A) from hole to hole.
Note: Do not damage the flange of the crankshaft during the removal process for the
crankshaft front seal.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:53:10 UTC+0800 2020
2/2(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742692
Crankshaft Front Seal - Install
SMCS - 1160-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6180 Front Seal Installer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
24. Illustration 1 g00612743
Typical Example
1. Clean the faces of all the mating parts. Apply a thin coat of clean engine oil to a new
crankshaft front seal.
2. Use Tooling (A) in order to install new crankshaft front seal (1) in the front housing.
3. Remove Tooling (A) and check crankshaft front seal (1) for correct installation.
4. Apply clean engine oil to the face of the crankshaft pulley that will be in contact with the
new crankshaft front seal.
End By:
a. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 23 09:54:06 UTC+0800 2020
2/2(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
25. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320D LRR EXCAVATOR EJT
Configuration: 320D LRR Excavator EJT00001-UP (MACHINE) POWERED BY C6.4 Engine
Disassembly and Assembly
C6.4 Engine for Caterpillar Built Machines
Media Number -KENR8106-09 Publication Date -01/10/2017 Date Updated -18/10/2017
i02742863
Gear Group (Front) - Remove - Idler Gear Only
SMCS - 1206-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6148 Idler Shaft Puller 1
B 1P-0510 Driver Group 1
Start By:
a. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
1/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
27. before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g01374732
(1) Fuel injection pump drive gear
(2) Idler gear
(3) Camshaft gear
(4) Crankshaft gear
Note: The No. 1 cylinder is at the top center position when these marks are in alignment.
Note: Ensure that the marks on the timing gears are in alignment.
2/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...
28. Illustration 2 g01374789
1. Remove idler gear bolt (5) and the washer from the idler gear shaft .
2. Remove thrust plate (6) from the idler gear shaft.
Illustration 3 g01374793
3. Remove idler gear (2) from the idler gear shaft.
Illustration 4 g01374804
4. If necessary, use Tooling (B) and a suitable press in order to remove bushing (7) (not
shown) from idler gear (2).
3/4(W)
w
2020/10/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sis...