The document provides instructions to disassemble and assemble the final drive of an excavator. Key steps include:
1. Removing the final drive cover, carrier assembly, ring gears, and other components.
2. Disassembling the carrier assembly by removing planetary gears and shafts.
3. Reassembling starts with installing bearings in the main housing and determining the correct shim thickness. Other parts like seals and gears are then reinstalled in reverse order of disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...cwmc101999
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...atow513211
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...jiyoushao19070
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, plates, gears, seals, and housing pieces.
3) The 33 steps for assembly describe installing seals, bearings, gears, shims, and housing pieces in reverse order. Proper cleaning, lubrication, and torque specifications are noted.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guituoya27447
This document provides instructions for disassembling and assembling the final drive of an excavator. It describes:
1) Removing over 30 individual parts of the final drive including gears, shafts, seals, housings and sprockets.
2) Disassembling carrier assemblies and planetary gear sets.
3) Cleaning all parts thoroughly before assembly to prevent dirt entry.
4) Reassembling the final drive by installing parts in reverse order and applying sealant compounds as needed.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...imvs79854181
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...jingcipo89419438
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, pins, gears, seals, and housing components.
3) The 33 steps for assembly describe installing seals, bearings, gears, shims, and housing components in reverse order. Precise alignment and cleanliness are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...heyong16820
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guangkaic18147
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...cwmc101999
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...atow513211
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...jiyoushao19070
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, plates, gears, seals, and housing pieces.
3) The 33 steps for assembly describe installing seals, bearings, gears, shims, and housing pieces in reverse order. Proper cleaning, lubrication, and torque specifications are noted.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guituoya27447
This document provides instructions for disassembling and assembling the final drive of an excavator. It describes:
1) Removing over 30 individual parts of the final drive including gears, shafts, seals, housings and sprockets.
2) Disassembling carrier assemblies and planetary gear sets.
3) Cleaning all parts thoroughly before assembly to prevent dirt entry.
4) Reassembling the final drive by installing parts in reverse order and applying sealant compounds as needed.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...imvs79854181
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...jingcipo89419438
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, pins, gears, seals, and housing components.
3) The 33 steps for assembly describe installing seals, bearings, gears, shims, and housing components in reverse order. Precise alignment and cleanliness are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...heyong16820
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...guangkaic18147
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and housing pieces.
3) The 31 steps for assembly describe installing seals, bearings, gears, and housing pieces in reverse order of disassembly. Proper cleaning, lubrication, and torque specifications are emphasized.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...s20y0196u
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...yi74411184285845
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...yu5676962
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and adjusting shims. Cleanliness is emphasized throughout to prevent contamination of parts.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...f9oseikkdks
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...jfkskmmdmdm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...jfkskmdmmdd
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
This document provides assembly instructions for an excavator final drive. It involves assembling several components in the following order:
1. Install the sprocket and bearings in the housing
2. Determine the correct shim thickness and install shims and coupling gear
3. Install seals, dowel pins, and connect the housing to the motor housing
4. Add remaining components like ring gear, planetary gears, and carrier assemblies
5. Secure components with pins, bolts, and retaining rings
The process requires precision measurements and cleaning/lubricating parts to ensure proper assembly.
More Related Content
Similar to Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP00001 and up).pdf
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...s20y0196u
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...yi74411184285845
1) The document provides step-by-step instructions for disassembling and assembling the final drive of an excavator.
2) It details 33 steps for disassembly, including removing bolts, seals, gears, and other components.
3) The 33 steps for assembly describe installing bearings, seals, gears, and other parts in reverse order of disassembly. Precise alignment and cleanliness are emphasized throughout.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...gongfuao7509
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and main housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...tengtui535
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...f8seodkdmdmed3
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...f8usiejdkmdd
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...yu5676962
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and adjusting shims. Cleanliness is emphasized throughout to prevent contamination of parts.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...f9oseikkdks
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar cat 318 d2 l excavator (prefix sgb) service repair manual (sgb000...fjskekdmjekm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and describes each step of the disassembly process, which includes removing covers, plates, gears, seals and other components. The assembly section then describes reversing each step and provides notes on cleaning, lubrication and installing new seals and O-rings during reassembly.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...jfkskmmdmdm
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 318D2 L Excavator (Prefix SGB) Service Repair Manual (SGB0000...jfkskmdmmdd
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the disassembled components. Cleanliness is emphasized throughout the process.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...f7djidksmd3e
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. It describes 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and seals. It then describes 31 steps for assembly, including pressing in bearings, determining shim thickness, installing seals and gears, and reassembling carrier assemblies. Precautions are given to clean parts and apply sealant or lubricant during assembly.
Caterpillar Cat 315D L Excavator (Prefix KBD) Service Repair Manual (KBD00001...paws21610697
This document provides instructions for disassembling and assembling the final drive of a 315D L excavator. The disassembly process involves using various tools to remove over 30 individual components from the final drive housing. The assembly process reverses the disassembly steps and provides details on installing bearings, seals, gears, and other components back into the housing using presses, lifting devices, and installation tools. Precise measurements are taken to determine the correct shim thickness for preloading the bearings. Cleanliness and lubrication of parts is emphasized throughout.
Similar to Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP00001 and up).pdf (20)
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
This document provides assembly instructions for an excavator final drive. It involves assembling several components in the following order:
1. Install the sprocket and bearings in the housing
2. Determine the correct shim thickness and install shims and coupling gear
3. Install seals, dowel pins, and connect the housing to the motor housing
4. Add remaining components like ring gear, planetary gears, and carrier assemblies
5. Secure components with pins, bolts, and retaining rings
The process requires precision measurements and cleaning/lubricating parts to ensure proper assembly.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...f8usueijdmm
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Multiple pages of detailed parts information are provided for the transmission, pilot controls, bulkhead plates, accumulators and other hydraulic systems.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
This document provides instructions for removing and installing a gear pump that is part of the secondary steering system on a 990K wheel loader. The 40 step removal procedure includes releasing hydraulic pressure, removing bolts, seals, valves, springs, and other components. Special care must be taken to contain fluids and avoid hot oil or components that could cause injury. Inspection and replacement of worn O-rings, gaskets and seals is recommended during disassembly. Thorough cleaning of parts is also important before reassembly.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head, including the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, and valve guides. The procedures involve using various tools to remove and install gaskets and seals, cleaning surfaces, and tightening bolts in a specific sequence while applying lubricants.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and installing seals and O-rings before positioning the rotor and housings back together.
3. Disconnecting hydraulic and electrical lines before removing the swing motor using lifting brackets.
4. Cleaning the swing motor and area before installation in reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise assembly is required to ensure proper governor function that regulates fuel delivery based on engine speed.
This document provides instructions for disassembling and assembling the governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing the fuel injection pump housing, governor housing, torque control group, and other components. Detailed steps are provided to disassemble the various parts of the governor system, including removing pins, plates, springs, and seals.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. The disassembly instructions list 37 steps to fully disassemble the governor. The assembly instructions list 40 steps to reassemble the governor, noting to apply clean oil to all parts before assembly and ensure all oil passages are clear.
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the transmission hydraulic control valve of a Caterpillar 637G wheel scraper. The disassembly procedure involves removing 19 parts in 19 steps, taking care with springs. The assembly procedure involves installing the 19 parts in reverse order, also taking care with springs. Tools required include retaining ring pliers.
This document provides instructions for removing and installing the camshaft on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Turning the engine upside down, removing the thrust washer and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft prior to installation and carefully reinstalling it along with the thrust washer.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318D2 L EXCAVATOR HBP
Configuration: 318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
318D2 Excavator Machine Systems
Media Number -UENR7326-02 Publication Date -01/11/2016 Date Updated -10/11/2016
i05453130
Final Drive - Disassemble
SMCS - 4050-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
C 154-6181 Forcing Bolt 1
D 439-3940 Link Bracket 2
E
5F-7366 Forcing Bolt 1
1P-5546 Crossblock 1
1U-9889 Crossblock 1
1P-0520 Driver Group 1
6V-7888 Puller Leg 2
1H-3112 Puller Assembly 1
1P-5551 Adjustable Screw Assembly 1
F - Loctite 5127 1
Start By:
a. Remove the final drive.
1/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Note: Cleanliness is an important factor. Before the disassembly procedure, thoroughly
clean the exterior of the component. This action will prevent dirt from entering the internal
mechanism.
1. Put an alignment mark across the sections of the final drive for assembly purposes. The
parts must be reinstalled in the original locations.
Illustration 1 g00708089
2. Fasten the final drive to Tooling (A), as shown. The combined weight of the final drive and
final drive sprocket is approximately 312 kg (688 lb).
3. Remove bolts (1) and the washers that hold the cover in position.
Illustration 2 g00708090
4. Remove the setscrews from cover (2), and fasten Tooling (B) and a suitable lifting device to
cover (2), as shown. The weight of cover (2) is approximately 32 kg (70 lb). Remove cover
(2).
2/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 3 g00708091
5. Remove thrust plate (3) from cover (2).
6. Remove plugs (4) from cover (2).
Illustration 4 g00708235
7. Remove O-ring seals (5) from both plugs (4) that were in the cover.
Illustration 5 g00708092
8. Remove spacer (6) from carrier assembly (7).
9. Remove sun gear (8) from carrier assembly (7).
3/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 10. Remove carrier assembly (7) by lifting the carrier assembly straight up. The weight of
carrier assembly (7) is approximately 14 kg (30 lb).
Illustration 6 g01304883
11. Disassemble carrier assembly (7), as follows.
a. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 7 g00708144
b. Remove planetary shaft (9) with spring pin (10) from the carrier assembly.
c. Remove spring pin (10) from planetary shaft (9) with a hammer and a punch.
4/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 8 g00708218
d. Remove thrust washers (11) and planetary gear (13) from the carrier assembly.
e. Remove bearing (12) from planetary gear (13).
12. Repeat Steps 11.a through 11.e in order to remove the remaining planetary gears from the
carrier assembly.
Illustration 9 g00708162
13. Remove sun gear (14) from carrier assembly (15).
Illustration 10 g00708325
14. Remove spacer (16).
5/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 11 g00708184
Note: It will be necessary to pry ring gears (17) away from main housing (18) in order to
install the lifting slings.
15. Fasten a suitable lifting device to ring gears (17), as shown. Remove the ring gears from
main housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 12 g00708360
16. Use a screwdriver or a chisel in order to separate two ring gears (17).
Note: Two ring gears (17) are held together with Tooling (F). It may be necessary to heat
ring gears (17) in order to soften the sealant. Do not heat over 135 °C (275 °F) for more
than thirty minutes.
6/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 13 g00708172
17. Position a 12.7 mm (0.50 inch) shackle under carrier assembly (15).
18. Fasten a suitable lifting device to the shackle.
19. Slowly lift carrier assembly (15) from the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Disassemble carrier assembly (15), as follows.
Illustration 14 g00708175
a. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
7/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 15 g00708370
Illustration 16 g00708220
b. Remove planetary shaft (19) with spring pin (20) from the carrier assembly.
c. Remove spring pin (20) from planetary shaft (19) with a hammer and a punch.
d. Remove thrust washers (21) and planetary gear (23) from the carrier assembly.
e. Remove bearings (22) from planetary gear (23).
21. Repeat Steps 20.a through 20.e in order to remove the remaining planetary gears from the
carrier.
Illustration 17 g00708186
22. Remove O-ring seal (24) from main housing (18).
8/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 18 g00708187
23. Remove bolts (25) from gear (26).
Illustration 19 g00708202
24. Use Tooling (C) in order to remove gear (26) from main housing (18).
Note: The motor housing will separate from main housing (18) once gear (26) is removed.
Make sure that the motor housing is supported.
Illustration 20 g00708211
25. Remove shims (27) from the main housing.
9/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 21 g00708212
26. Fasten Tooling (D) and a suitable lifting device to main housing (18), as shown.
27. Use a hammer and a punch in order to separate main housing (18) and the final drive
sprocket from motor housing (28). The combined weight of main housing (18) and the final
drive sprocket is approximately 82 kg (180 lb).
Illustration 22 g00708214
28. Remove Duo-Cone seal (29) from motor housing (28).
29. Remove alignment pins (30).
10/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 23 g00708215
Illustration 24 g00708216
30. Remove Duo-Cone seal (31) from main housing (18).
31. Use Tooling (E) in order to remove bearings (32) and (33) from the main housing.
32. If necessary, remove the final drive sprocket from the main housing.
33. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 18 00:03:04 UTC+0800 2020
11/11
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318D2 L EXCAVATOR HBP
Configuration: 318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
318D2 Excavator Machine Systems
Media Number -UENR7326-02 Publication Date -01/11/2016 Date Updated -10/11/2016
i05453369
Final Drive - Assemble
SMCS - 4050-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-2420 Transmission Repair Stand 1
B 439-3938 Link Bracket 2
D 439-3940 Link Bracket 2
G 126-3994 Duo-Cone Seal Installer 1
H - Loctite C5-A Anti-Seize Lubricant
F - Loctite High Flex From-In-Place Gasket
Note: Cleanliness is an important factor. Before assembly, all parts should be cleaned in
cleaning fluid. Allow the parts to air dry. Wiping cloths or rags should not be used to dry
parts. Lint may be deposited on the parts which may cause later trouble. Inspect all parts. If
any parts are worn or damaged, use new parts for replacement. All disassembly and all
assembly procedures must be performed on a clean work surface and in a clean hydraulic
area. Keep cleaned parts covered and protected at all times.
Note: O-rings, gaskets, and seals should always be replaced. A used O-ring may not have
the same sealing properties as a new O-ring. Use 1U-6396 O-Ring Assembly Compound
during the assembly procedure.
Note: Apply a light film of hydraulic oil to all components before assembly.
1. Install the final drive sprocket if the sprocket was removed from the main housing.
1/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. 2. Refer to Disassembly and Assembly, "Final Drive Sprocket - Remove and Install".
Illustration 1 g00708215
3. Apply Tooling (H) to the outer diameter of the bearings.
4. Install bearings (32) and (33) in main housing (18) with a suitable press.
5. Make sure that bearing (32) and bearing (33) contact the counter bore in the main housing.
6. Use the following procedure to preload the bearings and determine the correct thickness of
shims.
Illustration 2 g00713058
a. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
b. Put the main housing and the motor housing in a suitable press.
2/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00709278
(a) Bearing surface
(b) Housing surface
c. Use a suitable press and a spacer in order to apply a load of 4000 kg (8819 lb) on the
bearings. Rotate the housing in order to seat the bearings.
d. Reduce the load on the bearings to 1000 ± 100 kg (2205 ± 221 lb).
e. Use a depth micrometer in order to measure the step length between the bearing
surface and the housing surface. Take measurements at several different locations
around the housing. Compute the average of the measured dimensions and record the
number. Call this Dimension (Y).
Illustration 4 g00709276
f. Use a depth micrometer in order to measure the step length of gear (26). Take
measurements at several different locations around the gear. Compute the average of
the measured dimensions and record the number. Call this Dimension (X).
g. The thickness of the shims is equal to (X − Y) ± 0.05 mm (0.002 inch).
Note: Use no more than two shims. If two shims are required, install the thinner shim
next to the gear.
h. Remove the main housing from the motor housing.
3/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g01021370
7. Use Tooling (G) in order to install Duo-Cone seal (31) in main housing (18). Refer to
Disassembly and Assembly, "Duo-Cone Conventional Seals - Install".
Note: The rubber seals and all surfaces that contact the seals must be clean and dry. After
installation of the seals, put clean SAE 30 oil on the contact surfaces of the metal seals.
Illustration 6 g01021371
8. Use Tooling (G) in order to install Duo-Cone seal (29) in motor housing (28).
Illustration 7 g00708214
4/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 9. Apply Tooling (H) to the surfaces that contact pins (30).
10. Install alignment pins (30).
Note: Do not damage the Duo-Cone seals in the main housing or in the motor housing
during the assembly of the two components. After installation of the main housing on the
motor housing, there will be a small gap between the components. The gap is caused by the
Duo-Cone seals. This gap will be eliminated during installation of gear (26).
Illustration 8 g00713058
11. Fasten Tooling (D) and a suitable lifting device to main housing (18). Install the main
housing on the motor housing.
Illustration 9 g00708211
12. Install shims (27) that were determined in Step 6.g in the main housing.
Note: If two shims are required, install the thinner shim next to the gear.
5/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 10 g00708187
13. Install gear (26).
14. Install bolts (25) in gear (26). Install the bolts in an even pattern until the gear is seated
against the bearing. Tighten bolts (25) in a crisscross pattern.
Illustration 11 g00708186
15. Install O-ring seal (24) to main housing (18).
Illustration 12 g00708175
16. Assemble carrier assembly (15), as follows.
6/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 13 g00708220
a. Install bearings (22) in planetary gear (23).
b. Install thrust washers (21) and planetary gear (23) in the carrier assembly.
c. Use a deburring tool in order to remove the metal burr from the openings in the
carrier. Install planetary shaft (19) in the carrier assembly.
d. Drive spring pin (20) into planetary shaft (19) with a hammer and a punch.
Illustration 14 g00513451
e. Orient the split in spring pin (20) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
17. Repeat Steps 16.a through 16.e in order to install the remaining planetary gears in the carrier
assembly.
7/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 15 g00708172
18. Install a lifting sling through the middle of carrier assembly (15). Fasten a 12.7 mm
(0.50 inch) shackle to the suitable lifting device.
19. Install carrier assembly (15) on the final drive. The weight of carrier assembly (15) is
approximately 39 kg (85 lb).
20. Remove the shackle and the suitable lifting device.
Illustration 16 g00713148
21. Apply Tooling (F) to the mating surface of ring gear (17b).
22. Install ring gear (17a) on ring gear (17b).
8/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 17 g00708184
23. Fasten a suitable lifting device to ring gears (17), as shown. Install the ring gears to main
housing (18). The weight of ring gears (17) is approximately 45 kg (100 lb).
Illustration 18 g00708325
24. Install spacer (16) in the carrier assembly.
Illustration 19 g00708162
25. Install sun gear (14) in carrier assembly (15).
9/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 20 g01304883
Illustration 21 g00708218
26. Assemble carrier assembly (7), as follows.
a. Install bearing (12) in planetary gear (13).
b. Install thrust washers (11) and planetary gear (13) in the carrier assembly.
c. Install planetary shaft (9) in the carrier assembly.
d. Drive spring pin (10) into planetary shaft (9) with a hammer and a punch.
Illustration 22 g00513451
e. Orient the split in spring pin (10) vertically to the carrier. Align the split in the spring
pin to the top or to the bottom. Make a stake mark on each side of the spring pin hole
in the carrier. Each stake mark should be approximately 1.50 mm (0.059 inch) from
the outside diameter of the spring pin hole.
10/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 27. Repeat Steps 26.a through 26.e in order to install the remaining planetary gears in the carrier
assembly.
Illustration 23 g00708092
28. Install carrier assembly (7) in the ring gear. The weight of carrier assembly (7) is
approximately 14 kg (30 lb).
29. Install sun gear (8) in carrier assembly (7).
30. Install spacer (6) in carrier assembly (7).
Illustration 24 g00708235
31. Install new O-ring seals (5) on plugs (4) that were in the cover.
11/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 25 g00708091
32. Install plugs (4) in cover (2). Tighten plugs (4) to a torque of 80 ± 10 N·m (59 ± 7 lb ft).
33. Install thrust plate (3) in cover (2).
34. Apply Tooling (F) to the mating surface of the ring gear.
Illustration 26 g00708090
35. Fasten Tooling (B) and a suitable lifting device to cover (2), as shown. The weight of cover
(2) is approximately 32 kg (70 lb). Install cover (2).
36. Remove Tooling (B) and install the setscrews in cover (2).
Illustration 27 g00708089
37. Install bolts (1) and the washers that hold the cover in position. Tighten bolts (1) in a
crisscross pattern.
38. Remove the final drive from Tooling (A). The combined weight of the final drive and final
drive sprocket is approximately 310 kg (683 lb).
End By:
a. Install the final drive.
12/13
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEB...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318D2 L EXCAVATOR HBP
Configuration: 318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
318D2 Excavator Machine Systems
Media Number -UENR7326-02 Publication Date -01/11/2016 Date Updated -10/11/2016
i07192988
Final Drive - Install
SMCS - 4050-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-7611 Handle As 2
8S-7615 Pin As 2
283-1495 Stand Assembly 2
B 439-3939 Link Bracket As 2
C - Loctite C5A Copper Anti-Seize -
Table 2
Torque Values of Bolts (3)
Bolt Size Torque
M16 90 ± 15 N·m (66 ± 11 lb ft) and turn an additional angle of 60 ± 5 degrees.
M20 150 ± 25 N·m (111 ± 18 lb ft) and turn an additional angle of 55 ± 5 degrees.
M24 250 ± 25 N·m (184 ± 18 lb ft) and turn an additional angle of 45 ± 5 degrees.
M30 500 ± 50 N·m (369 ± 37 lb ft) and turn an additional angle of 50 ± 5 degrees.
1/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00712767
1. Attach Tooling (B) and a suitable lifting device to final drive (1). The weight of final drive
(1) and the sprocket is approximately 312 kg (688 lb). Position the final drive in the frame.
Illustration 2 g00712737
Note: Make sure that bolt holes (2) for the travel motor are in the correct position.
Note: Make sure that bolts (3), the washers, the motor housing, and the frame are clean and
free of protective coating and oil.
2. Before assembly remove all compounds, oil, and dust from the female threads.
3. Apply Tooling (C) to the threads of bolt (3). Install bolts (3) and the washers in the final
drive. Tighten bolts (3) to a torque specified in Table 2.
4. Refer to Service Magazine, M0083843, "An Improved Bolt Tightening Procedure for the
Critical Joints Is Now Used on All Excavators" for more detail information.
5. Remove Tooling (B) and the suitable lifting device from the final drive.
2/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 3 g00489826
Typical Example
6. Lift the side of the machine to remove Tooling (A).
End By:
a. Install the travel motor.
b. Connect the track assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 18 00:05:02 UTC+0800 2020
3/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318D2 L EXCAVATOR HBP
Configuration: 318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
318D2 Excavator Machine Systems
Media Number -UENR7326-02 Publication Date -01/11/2016 Date Updated -10/11/2016
i01001305
Swivel - Remove
SMCS - 5060-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
(A) 138-7573 Link Bracket 1
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
29. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
30. At operating temperature the implement hydraulic oil tank is hot and
under pressure. Hot oil can cause burns.
To prevent possible injury, release the pressure in the implement
hydraulic system before hydraulic lines or components are disconnected
or removed.
1. Release the hydraulic system pressure. Refer to Disassembly and Assembly, "Hydraulic
System Pressure - Release" in this manual.
2. Clean the outside of the swivel joint and the area around the swivel joint prior to removal.
Illustration 1 g00513210
3. Oil will drain from all hose assemblies that are connected to the swivel joint. Place suitable
containers under the machine in the area of the swivel joint in order to collect the oil.
4. Put identification marks on seven hose assemblies (1) for installation purposes. Disconnect
seven hose assemblies (1) from the swivel joint. Put plugs in the ends of the hose assemblies
in order to prevent oil loss and keep contaminants out of the hydraulic system.
5. Remove two bolts (2) and the washers that hold setting plate (3) in position. Remove setting
plate (3).
6. Remove eight bolts (4).
7. Remove one cover bolt from the swivel joint. Reuse the cover bolt in order to fasten Tool
(A) to the swivel joint. Fasten a hoist to Tool (A).
2/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 2 g00513213
This view is from the underside of the machine.
8. Remove bolts (5) and two cover assemblies (6) from the underside of the undercarriage
frame assembly.
Illustration 3 g00513219
This view is from the underside of the machine.
9. Put identification marks on eight hose assemblies (7) for installation purposes. Disconnect
eight hose assemblies (7) from the bottom of the swivel joint. Put plugs in the ends of the
hose assemblies in order to prevent oil loss and keep contaminants out of the hydraulic
system.
10. Remove tee fitting (8) from the swivel joint.
11. Cover the ports in the bottom of the swivel joint with tape in order to keep dirt and debris
out of the unit.
12. Remove six bolts (9).
13. Remove the swivel joint from the machine. The weight of the swivel joint is 43 kg (95 lb).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 18 00:06:02 UTC+0800 2020
3/3
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 318D2 L EXCAVATOR HBP
Configuration: 318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine
Disassembly and Assembly
318D2 Excavator Machine Systems
Media Number -UENR7326-02 Publication Date -01/11/2016 Date Updated -10/11/2016
i01961404
Swivel - Remove
SMCS - 5060-011
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
At operating temperature the implement hydraulic oil tank is hot and
under pressure. Hot oil can cause burns.
To prevent possible injury, release the pressure in the implement
hydraulic system before hydraulic lines or components are disconnected
or removed.
1/4
318D2 L Excavator HBP00001-UP (MACHINE) POWERED BY C4.4 Engine(SEBP...
2020/11/18
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...