This document provides instructions for removing and installing a gear pump that is part of the secondary steering system on a 990K wheel loader. The 40 step removal procedure includes releasing hydraulic pressure, removing bolts, seals, valves, springs, and other components. Special care must be taken to contain fluids and avoid hot oil or components that could cause injury. Inspection and replacement of worn O-rings, gaskets and seals is recommended during disassembly. Thorough cleaning of parts is also important before reassembly.
Caterpillar cat 962 h wheel loader (prefix pcw) service repair manual (pcw000...dikdkskmmdm
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals, and shafts. Tools required include link brackets, a transmission repair stand, retaining ring pliers, drivers, and bearing pullers. Cleanliness is important during assembly and disassembly to prevent dirt ingress.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations are provided for each step. Cleanliness is emphasized when handling parts.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations accompany each step. Cleanliness is emphasized when handling parts.
Caterpillar cat 962 h wheel loader (prefix pcw) service repair manual (pcw000...fjjskkemsmee
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations accompany each step. Cleanliness is emphasized when handling parts.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations are provided for each step. Cleanliness is emphasized when handling parts.
Caterpillar cat 962 h wheel loader (prefix pcw) service repair manual (pcw000...dikdkskmmdm
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals, and shafts. Tools required include link brackets, a transmission repair stand, retaining ring pliers, drivers, and bearing pullers. Cleanliness is important during assembly and disassembly to prevent dirt ingress.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations are provided for each step. Cleanliness is emphasized when handling parts.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations accompany each step. Cleanliness is emphasized when handling parts.
Caterpillar cat 962 h wheel loader (prefix pcw) service repair manual (pcw000...fjjskkemsmee
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations accompany each step. Cleanliness is emphasized when handling parts.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission on a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, beginning with removing O-rings and bolts from the housing. Various tools are required including retaining ring pliers and a bearing puller. Detailed illustrations accompany each step. The goal is to disassemble the transmission components in preparation for inspection or repair.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutches, gears, seals and shafts using various tools. Detailed illustrations are provided for each step. Cleanliness is emphasized when handling parts.
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutch plates, gears, seals, and shafts using various tools. Illustrations are provided to identify the specific components at each step. The overall document provides detailed technical instructions for servicing the power train transmission.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjsekdhjenmdn
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with diagrams and notes about releasing pressure and supporting lifted components.
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...dikdkskmdm
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...cdfzxs
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with diagrams and notes about releasing pressure and supporting lifted components.
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, springs, and bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches, and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts and covers.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before servicing hydraulic systems.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjjskekdm
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before working on hydraulic systems.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...fjskekxcddmmme
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
This document provides assembly instructions for an excavator final drive. It involves assembling several components in the following order:
1. Install the sprocket and bearings in the housing
2. Determine the correct shim thickness and install shims and coupling gear
3. Install seals, dowel pins, and connect the housing to the motor housing
4. Add remaining components like ring gear, planetary gears, and carrier assemblies
5. Secure components with pins, bolts, and retaining rings
The process requires precision measurements and cleaning/lubricating parts to ensure proper assembly.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...f8usueijdmm
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Multiple pages of detailed parts information are provided for the transmission, pilot controls, bulkhead plates, accumulators and other hydraulic systems.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head, including the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, and valve guides. The procedures involve using various tools to remove and install gaskets and seals, cleaning surfaces, and tightening bolts in a specific sequence while applying lubricants.
More Related Content
Similar to Caterpillar Cat 990K Wheel Loader (Prefix A9P) Service Repair Manual (A9P00001 and up).pdf
This document provides instructions for assembling and disassembling components of the torque converter and transmission for a 962H wheel loader. It includes 29 steps to disassemble the transmission planetary, involving removing housing components, clutch plates, gears, seals, and shafts using various tools. Illustrations are provided to identify the specific components at each step. The overall document provides detailed technical instructions for servicing the power train transmission.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjsekdhjenmdn
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with diagrams and notes about releasing pressure and supporting lifted components.
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...dikdkskmdm
This document provides instructions for assembling a piston pump and removing and installing a main control valve. It includes 31 steps for assembling the piston pump, requiring various tools and involving installation of numerous parts in the correct order. It also lists the required tools and provides 7 steps for removing a joystick control and 1 step for installing it.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...cdfzxs
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, and tightening bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with diagrams and notes about releasing pressure and supporting lifted components.
This document provides instructions for assembling and disassembling components of a 962K wheel loader, including:
- Assembling the piston pump by installing various parts like covers, bearings, seals, pistons, springs, and bolts in the correct order.
- Removing and installing the electrohydraulic control by disconnecting harnesses and removing screws, switches, and covers.
- Removing the main control valve by draining fluids, disconnecting hoses and harnesses, and removing mounting bolts and covers.
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before servicing hydraulic systems.
Caterpillar cat 962 k wheel loader (prefix t6a) service repair manual (t6a000...fjjskekdm
This document provides instructions for assembling and disassembling parts of a 962K wheel loader. It includes 37 steps to assemble a piston pump, with diagrams showing each step. It also provides procedures for removing and installing a main control valve and electrohydraulic control components, with warnings about releasing pressure before working on hydraulic systems.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...fjskekxcddmmme
The document provides instructions for assembling a travel motor. It describes 33 steps including installing seals, spacers, pistons, disks, and other components in the proper order and orientation. Measurements are checked at several steps to ensure correct assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...cdsaas
The document provides instructions for assembling a travel motor. It describes 33 steps for installing various components like seals, pistons, plates, and bearings. Measurements are taken throughout to ensure proper assembly. Cleanliness is emphasized to prevent contaminating the hydraulic system. The travel motor must be filled with the correct oil type before operation to prevent damage.
Caterpillar cat 349 d l excavator (prefix khs) service repair manual (khs0000...hhfjksekmm
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection from contamination during installation is emphasized.
Caterpillar Cat 349D L Excavator (Prefix KHS) Service Repair Manual Instant D...f89siekkmdmm2w
This document provides instructions for installing a travel motor on an excavator. It lists the required tools and parts. The procedure has 33 steps that include installing seals, spacers, pistons, plates, and bolts in the proper sequence and orientation. Measurements are taken throughout to ensure correct assembly. Proper cleaning and protection of parts from contamination is emphasized.
Similar to Caterpillar Cat 990K Wheel Loader (Prefix A9P) Service Repair Manual (A9P00001 and up).pdf (15)
1) The document provides assembly instructions for a final drive on an excavator.
2) It involves over 40 steps to assemble bearings, seals, gears, carriers, housing and cover components.
3) Special tools and procedures are required to set bearing preloads, install seals, and test for leaks. Proper torque values and sealants are specified.
This document provides assembly instructions for an excavator final drive. It involves assembling several components in the following order:
1. Install the sprocket and bearings in the housing
2. Determine the correct shim thickness and install shims and coupling gear
3. Install seals, dowel pins, and connect the housing to the motor housing
4. Add remaining components like ring gear, planetary gears, and carrier assemblies
5. Secure components with pins, bolts, and retaining rings
The process requires precision measurements and cleaning/lubricating parts to ensure proper assembly.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...f8usueijdmm
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Multiple pages of detailed parts information are provided for the transmission, pilot controls, bulkhead plates, accumulators and other hydraulic systems.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. It describes:
1) Removing over 30 components of the final drive including gears, shafts, bearings, seals and hubs using various tools.
2) Inspecting all parts and replacing any that are damaged.
3) Heating some bearings cones to aid removal and ensuring proper temperatures when installing.
4) Precisely assembling the components in reverse order, taking care with sealing surfaces.
The document provides instructions for disassembling and assembling a recoil cylinder. Key steps include:
1. Removing the recoil cylinder and various components like bolts, guards, valves, and seals.
2. Inspecting parts and cleaning components as needed.
3. Reassembling the recoil cylinder by reinstalling components in reverse order and applying lubricants and seals. Precise torques are specified.
4. The process involves over 20 numbered steps and utilizes various specialized tools to properly disassemble and reassemble the recoil cylinder.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torques are specified for tightening bolts and nuts.
The document provides instructions for removing and installing various components of a 3406C diesel engine cylinder head, including the cylinder head assembly, spacer plate, valves, valve seat inserts, bridge dowels, and valve guides. The procedures involve using various tools to remove and install gaskets and seals, cleaning surfaces, and tightening bolts in a specific sequence while applying lubricants.
The document provides instructions for disassembling and assembling a swivel and swing motor on an excavator. Key steps include:
1. Cleaning and removing bolts and seals to separate the swivel housing, rotor, and cover.
2. Cleaning and installing seals and O-rings before positioning the rotor and housings back together.
3. Disconnecting hydraulic and electrical lines before removing the swing motor using lifting brackets.
4. Cleaning the swing motor and area before installation in reverse order.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise assembly is required to ensure proper governor function that regulates fuel delivery based on engine speed.
This document provides instructions for disassembling and assembling the governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing the fuel injection pump housing, governor housing, torque control group, and other components. Detailed steps are provided to disassemble the various parts of the governor system, including removing pins, plates, springs, and seals.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. The disassembly instructions list 37 steps to fully disassemble the governor. The assembly instructions list 40 steps to reassemble the governor, noting to apply clean oil to all parts before assembly and ensure all oil passages are clear.
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for removing and installing the cylinder head assembly on a 3204 vehicular engine. It describes:
1) Removing the cylinder head assembly by loosening hoses, removing bolts, and lifting it off with a hoist.
2) Cleaning and installing a new gasket before lowering the cylinder head back onto the cylinder block and tightening bolts in a specific sequence and torque.
3) Checking the flatness of the cylinder head and block surfaces during installation.
This document provides instructions for disassembling and assembling the transmission hydraulic control valve of a Caterpillar 637G wheel scraper. The disassembly procedure involves removing 19 parts in 19 steps, taking care with springs. The assembly procedure involves installing the 19 parts in reverse order, also taking care with springs. Tools required include retaining ring pliers.
Caterpillar Cat 318D2 L Excavator (Prefix HBP) Service Repair Manual (HBP0000...f8usueijdmm
The document provides instructions to disassemble and assemble the final drive of an excavator. Key steps include:
1. Removing the final drive cover, carrier assembly, ring gears, and other components.
2. Disassembling the carrier assembly by removing planetary gears and shafts.
3. Reassembling starts with installing bearings in the main housing and determining the correct shim thickness. Other parts like seals and gears are then reinstalled in reverse order of disassembly.
This document provides instructions for removing and installing the camshaft on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Turning the engine upside down, removing the thrust washer and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft prior to installation and carefully reinstalling it along with the thrust washer.
How to Prepare for Fortinet FCP_FAC_AD-6.5 Certification?NWEXAM
Begin Your Preparation Here: https://bit.ly/3VfYStG — Access comprehensive details on the FCP_FAC_AD-6.5 exam guide and excel in the Fortinet Certified Professional - Network Security certification. Gather all essential information including tutorials, practice tests, books, study materials, exam questions, and the syllabus. Solidify your knowledge of Fortinet FCP_FAC_AD-6.5 certification. Discover everything about the FCP_FAC_AD-6.5 exam, including the number of questions, passing percentage, and the time allotted to complete the test.
Leadership Ambassador club Adventist modulekakomaeric00
Aims to equip people who aspire to become leaders with good qualities,and with Christian values and morals as per Biblical teachings.The you who aspire to be leaders should first read and understand what the ambassador module for leadership says about leadership and marry that to what the bible says.Christians sh
IT Career Hacks Navigate the Tech Jungle with a RoadmapBase Camp
Feeling overwhelmed by IT options? This presentation unlocks your personalized roadmap! Learn key skills, explore career paths & build your IT dream job strategy. Visit now & navigate the tech world with confidence! Visit https://www.basecamp.com.sg for more details.
Joyce M Sullivan, Founder & CEO of SocMediaFin, Inc. shares her "Five Questions - The Story of You", "Reflections - What Matters to You?" and "The Three Circle Exercise" to guide those evaluating what their next move may be in their careers.
A Guide to a Winning Interview June 2024Bruce Bennett
This webinar is an in-depth review of the interview process. Preparation is a key element to acing an interview. Learn the best approaches from the initial phone screen to the face-to-face meeting with the hiring manager. You will hear great answers to several standard questions, including the dreaded “Tell Me About Yourself”.
Learnings from Successful Jobs SearchersBruce Bennett
Are you interested to know what actions help in a job search? This webinar is the summary of several individuals who discussed their job search journey for others to follow. You will learn there are common actions that helped them succeed in their quest for gainful employment.
In the intricate tapestry of life, connections serve as the vibrant threads that weave together opportunities, experiences, and growth. Whether in personal or professional spheres, the ability to forge meaningful connections opens doors to a multitude of possibilities, propelling individuals toward success and fulfillment.
Eirini is an HR professional with strong passion for technology and semiconductors industry in particular. She started her career as a software recruiter in 2012, and developed an interest for business development, talent enablement and innovation which later got her setting up the concept of Software Community Management in ASML, and to Developer Relations today. She holds a bachelor degree in Lifelong Learning and an MBA specialised in Strategic Human Resources Management. She is a world citizen, having grown up in Greece, she studied and kickstarted her career in The Netherlands and can currently be found in Santa Clara, CA.
Jill Pizzola's Tenure as Senior Talent Acquisition Partner at THOMSON REUTERS...dsnow9802
Jill Pizzola's tenure as Senior Talent Acquisition Partner at THOMSON REUTERS in Marlton, New Jersey, from 2018 to 2023, was marked by innovation and excellence.
5. 7. Install bearings (55) to swashplate (53). Use Tooling (B) to hold the bearings in place for
installation.
8. Install swashplate (53) and remove Tooling (B).
Illustration 10 g06153892
9. Install retainers (51), plugs (52) and the O-rings. Repeat for opposite side.
Note: Ensure retainers (51) lock into pins (54) shown in illustration 7..
Illustration 11 g06153894
10. Install adjustment screw (50) into housing (30). Repeat for opposite side.
5/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 12 g06153856
11. Place port plate (31) on a flat surface and install Tooling (G).
Illustration 13 g06149897
12. Install Tooling (F) into bearing (49).
Illustration 14 g06149905
13. Install shims (47) into bearing (49).
Illustration 15 g06149911
6/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 14. Install bearing (49) onto barrel (44).
Illustration 16 g06153902
Dimension (X) is 220.95 - 221.20mm (8.698 - 8.708 inch)
Dimension (Y) is 170.95 - 171.20mm (6.730- 6.740 inch)
15. Install barrel assembly (44) onto port plate (31). Install retainer plate (46) onto barrel
assembly (44). Install Tooling (C) and (D) onto retainer plate (46).
16. Use Tooling (G) to measure dimensions (X) and (Y). Adjust the shims under retainer plate
(46) as necessary to achieve the dimensions shown in Illustration 16.
17. Remove Tooling (C) and (D). Remove retainer plate (46) from barrel assembly (44).
Remove barrel assembly (44) from port plate (31).
Illustration 17 g06149911
18. Remove bearing (49) from barrel (44).
7/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 21 g06149905
21. Apply Tooling (H) to springs (48). Install springs (48) and shims (47) into bearing (49).
Illustration 22 g06149911
22. Install bearing (49) onto barrel (44).
Illustration 23 g06146401
23. Install retainer plate (46) and pistons (45) into barrel (44).
9/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 24 g06146790
24. Rotate housing (30) to a horizontal position. Use a suitable string to install barrel assembly
(44) into housing (30).
Illustration 25 g06146314
25. Apply Tooling (J) to bolts (42). Install retainer (43) and bolts (42). Repeat for opposite side.
Note: Bolts (42) should be replaced with new bolts.
Illustration 26 g06146295
26. Install cover (41). Repeat for opposite side.
10/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 27 g06154614
Illustration 28 g06154626
27. Install O-ring seal (39). Install rods (40) and (38). Install piston (37), spring (36), spring
(35), and piston (34).
Illustration 29 g06153915
28. Install bushing (33) and bearing (32) into head (29). Apply Tooling (H) to port plate (31)
and install into head (29).
11/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 30 g06146219
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
29. Attach Tooling (B) and a suitable lifting device to head (29). Install head (29) onto housing
(30).
Illustration 31 g06146174
30. Install bolts (28). Tighten bolts (28) to a torque of 780 ± 78 N·m (575 ± 58 lb ft). Install
plug (27) and the O-ring seal. Tighten plug (27) to a torque of 198 ± 20 N·m
(146 ± 15 lb ft).
12/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 32 g06146164
Illustration 33 g06146158
31. Install plugs (26), (25), and the O-ring seals.
Illustration 34 g06153150
32. Install retaining ring (24A).
13/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 35 g06153932
33. Install impeller (23) and retaining ring (24).
Illustration 36 g06145926
34. Install adapter (22) and the O-ring seal. Install bolts (21).
Illustration 37 g06145925
35. Install adapter (20) and the O-ring seal. Install bolts (19). Install coupler (18).
14/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 38 g06145907
Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
36. Install spool (11), guide (12), spring (13), spring (14), guide (15), O-ring seal (16), and
valve (17).
37. Install spool (5), guide (6), spring (7), guide (8), O-ring seal (9), and valve (10).
Illustration 39 g06145896
38. Install O-ring seals (4).
15/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 40 g06145891
39. Install valve (2) and bolts (3).
Illustration 41 g06145889
40. Install plug (1) and the O-ring seal. Remove the piston pump from Tooling (A).
End By:
a. Install the piston pump.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 23 17:33:33 UTC+0800 2021
16/16
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEB...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 990K WHEEL LOADER A9P
Configuration: 990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine
Disassembly and Assembly
990K Wheel Loader and 844K Wheel Dozer Machine Systems
Media Number -UENR6576-05 Publication Date -01/01/2018 Date Updated -26/01/2018
i06545830
Gear Pump (Secondary Steering) - Remove and Install
SMCS - 4324-010-GT; 4324-010; 5073-010-SST; 5073-010
Removal Procedure
Start by:
a. Connect the steering frame lock.
b. Release the hydraulic system pressure.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting, and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Dealer Service Tool
Catalog" for tools and supplies suitable to collect and contain fluids on
Cat®
products.
Dispose of all fluids according to local regulations and mandates.
Hot oil and hot components can cause personal injury. Do not allow hot
oil or hot components to contact skin.
1/3
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected always.
1. Drain the transmission oil into a suitable container for storage or disposal. Refer to
Operation and Maintenance Manual, "Transmission Oil - Change". Drain enough oil to
bring the oil level below the secondary steering pump.
Illustration 1 g00346175
2. Disconnect hose assemblies (2) from secondary steering pump (3).
Illustration 2 g00346174
3. Remove nuts (4) and secondary steering pump (3).
2/3
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 3 g00346176
4. Remove gasket (5) from the pump drive.
Installation Procedure
1. Install secondary steering pump (3) in the reverse order of removal.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 23 17:34:30 UTC+0800 2021
3/3
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 990K WHEEL LOADER A9P
Configuration: 990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine
Disassembly and Assembly
990K Wheel Loader and 844K Wheel Dozer Machine Systems
Media Number -UENR6576-05 Publication Date -01/01/2018 Date Updated -26/01/2018
i00761547
Gear Pump (Secondary Steering) - Disassemble
SMCS - 4324-015-GT; 5073-015-SST
Disassembly Procedure
Start By:
a. Remove the secondary steering pump. Refer to Disassembly and Assembly, "Gear Pump
(Secondary Steering) - Remove".
Illustration 1 g00346187
1. Remove bolts (1) and the washers. Remove body (2) from the secondary steering pump.
1/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 2 g00346188
2. Remove two pistons (3) and two springs from body (2).
3. Remove two seals (4) from body (2).
Illustration 3 g00346189
4. Remove spacer (5) from body assembly (6).
Illustration 4 g00346190
5. Remove two spacers (7) from spacer (5).
2/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 5 g00346191
6. Remove two pistons (8) and two springs (9) from body assembly (6).
Illustration 6 g00346232
7. Remove two seals (10) from body assembly (6).
Illustration 7 g00346233
8. Remove bolts (11) and the washers from flange assembly (12). Remove flange assembly
(12) from body assembly (6).
3/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 8 g00346234
9. Remove seal (13) from flange assembly (12).
Illustration 9 g00346235
10. Remove seals (14) from bushings (15).
Illustration 10 g00346236
11. Remove two dowels (16) and two bushings (15) from flange assembly (12).
4/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 11 g00346237
12. Remove two lip seals (17) and the ring from flange assembly (12).
Illustration 12 g00346239
Illustration 13 g00346240
13. Remove two metal seals (18) and five plastic seals (19) from body assembly (6).
5/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
26. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
27. Illustration 14 g00346241
14. Remove plate (20) from body assembly (6).
Illustration 15 g00346242
15. Remove shaft (21) and gear (22) from body assembly (6).
Illustration 16 g00346243
16. Remove plate (23) from body assembly (6).
6/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 17 g00346244
Illustration 18 g00346245
17. Remove two metal seals (24) and five plastic seals (25) from body assembly (6).
Illustration 19 g00346246
18. Remove seals (26) from bushings (27). Remove bushings (27).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Nov 23 17:35:27 UTC+0800 2021
7/7
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Shutdown SIS
Previous Screen
Product: WHEEL LOADER
Model: 990K WHEEL LOADER A9P
Configuration: 990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine
Disassembly and Assembly
990K Wheel Loader and 844K Wheel Dozer Machine Systems
Media Number -UENR6576-05 Publication Date -01/01/2018 Date Updated -26/01/2018
i01281269
Gear Pump (Secondary Steering) - Assemble
SMCS - 4324-016-GT; 5073-016-SST
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Gp 1
Note: Thoroughly clean all parts of the secondary steering pump prior to assembly.
1. Check the condition of all seals. If any seals are worn or damaged, use new parts for
replacement . Lubricate the seals with clean hydraulic oil.
2. Apply clean hydraulic oil on all internal parts of the secondary steering pump.
NOTICE
Failure to follow the recommended procedure or the specified tooling
that is required for the procedure could result in damage to
components.
To avoid component damage, follow the recommended procedure
using the recommended tools.
Note: Two isolation plates are required for the bottom of the pump housing. Two isolation
plates are required for the top of the pump housing. The isolation plates hold the seal
components together. The isolation plates that have round edges on one outer radius will be
1/8
990K Wheel Loader A9P00001-UP (MACHINE) POWERED BY C27 Engine(SEBP6...
2021/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...