Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Symptoms like intermittent starting and key recognition errors signal potential problems with your Mercedes’ EIS. Use diagnostic steps like error code checks and spare key tests. Professional diagnosis and solutions like EIS replacement ensure safe driving. Consult a qualified technician for accurate diagnosis and repair.
Why Is Your BMW X3 Hood Not Responding To Release CommandsDart Auto
Experiencing difficulty opening your BMW X3's hood? This guide explores potential issues like mechanical obstruction, hood release mechanism failure, electrical problems, and emergency release malfunctions. Troubleshooting tips include basic checks, clearing obstructions, applying pressure, and using the emergency release.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
5 Warning Signs Your BMW's Intelligent Battery Sensor Needs AttentionBertini's German Motors
IBS monitors and manages your BMW’s battery performance. If it malfunctions, you will have to deal with an array of electrical issues in your vehicle. Recognize warning signs like dimming headlights, frequent battery replacements, and electrical malfunctions to address potential IBS issues promptly.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Core technology of Hyundai Motor Group's EV platform 'E-GMP'Hyundai Motor Group
What’s the force behind Hyundai Motor Group's EV performance and quality?
Maximized driving performance and quick charging time through high-density battery pack and fast charging technology and applicable to various vehicle types!
Discover more about Hyundai Motor Group’s EV platform ‘E-GMP’!
What Exactly Is The Common Rail Direct Injection System & How Does It WorkMotor Cars International
Learn about Common Rail Direct Injection (CRDi) - the revolutionary technology that has made diesel engines more efficient. Explore its workings, advantages like enhanced fuel efficiency and increased power output, along with drawbacks such as complexity and higher initial cost. Compare CRDi with traditional diesel engines and discover why it's the preferred choice for modern engines.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02453078
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
C. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to remove the liner wear ridge from the inner surface of the cylinder liner.
2. Position the two pistons that are being removed at the bottom center position.
1/2
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00550548
3. Remove nuts (1) and the bolts.
4. Remove connecting rod caps (2) and the connecting rod bearings. Keep connecting rod caps
(2) and the connecting rod bearings together for installation.
Illustration 2 g00550549
5. Push pistons (3) and the connecting rods out of the top of cylinder block (4) .
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 28 23:25:23 UTC+0800 2020
2/2
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02088687
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00551459
Typical example
1. Use Tooling (A) in order to remove three piston rings (1) from piston (2).
Illustration 2 g00551460
Typical example
2. Use Tooling (B) in order to remove retaining rings (3) that hold the piston pin in position.
3. Remove piston pin (4) from the piston.
Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of
45 ± 5 °C (113 ± 9 °F). Do not use a torch to heat the piston.
4. Remove bearing (5) from connecting rod (6).
2/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00893862
5. Use a suitable press and a suitable adapter in order to remove piston pin bushing (7) from
connecting rod (6).
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 28 23:26:20 UTC+0800 2020
3/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02088688
Pistons and Connecting Rods - Assemble
SMCS - 1225-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 1 g00893862
1. Ream piston pin bushing (7) in order to obtain a clearance of 0.0085 ± 0.0055 mm
(0.00030 ± 0.00020 inch) between the piston pin and the piston pin bushing.
2. Lubricate all components with clean engine oil.
3. Use a suitable press and a suitable adapter to install piston pin bushing (7) into connecting
rod (6).
Note: Ensure that the oil hole in the piston pin bushing is aligned with the oil hole at the top
of the connecting rod.
2/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 2 g00551460
Typical example
4. Install bearing (5) in connecting rod (6).
5. Install piston pin (4) into the piston and through connecting rod (6).
Note: If the piston pin cannot be installed by hand, heat the piston to a temperature of
45° ± 5°C (113° ± 9°F).
6. Use Tooling (B) in order to install retaining rings (3) that hold the piston pin in position.
Illustration 3 g00551459
7. Use Tooling (A) in order to install piston rings (1) on piston (2) with the following steps.
a. Install the oil control piston ring in the groove that is lowest on the piston. The latch
pin that is on the oil control ring must be inside the ends of the spring.
Note: Ensure that the latch pin that is on the oil control ring is 180 degrees from the
oil control ring gap.
b. Install the intermediate piston ring with the tapered face into the second groove on the
piston. The stamp "TOP" must be toward the top of the piston.
Note: Intermediate piston rings that are new have a green mark which must be on the
left of the piston ring gap when the piston ring is installed.
c. Position the piston ring gaps at 120 degrees away from each other.
d. Install the top piston ring with the barrel face and the molybdenum insert into the top
groove on the piston. The top piston ring has a wedge shape. The stamp "TOP" must
be toward the top of the piston.
Note: Top piston rings that are new have a red mark which must be on the left of the
ring gap when the ring is installed.
End By:
a. Install the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston and
Connecting Rods - Install".
3/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02453085
Pistons and Connecting Rods - Install
SMCS - 1225-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
B 1U-6684 Piston Ring Compressor 1
C 8T-0455 Liner Projection Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Thoroughly clean all of the components.
2. Lubricate the piston and the cylinder liner with clean engine oil.
3. Rotate the crankshaft until the connecting rod journal is at the bottom center. Lubricate the
connecting rod journal with clean engine oil.
4. Install the upper connecting rod bearing cap in the connecting rod. Ensure that the locating
tab is correctly installed in the connecting rod.
5. Lubricate the bearing for the upper connecting rod journal with clean engine oil.
1/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 6. Align the piston rings on the piston so that the distance between the gaps is 120 degrees.
Illustration 1 g01224228
7. Install Tooling (B) on the piston.
Note: Ensure that Tooling (B) is installed correctly and that the piston can easily slide out of
the Tooling.
Note: The arrow or "FRONT" Mark that is on the top of the piston must be toward the front
of the engine.
8. Push the piston and the connecting rod assembly into the cylinder liner and onto the
connecting rod journal.
9. Install the lower connecting rod bearing in the connecting rod cap. Ensure that the locating
tab is correctly installed in the connecting rod cap.
10. Lubricate the lower connecting rod bearing with clean engine oil.
Illustration 2 g00550548
11. Install connecting rod caps (2) with the bolts and nuts (1) .
2/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. 12. Use the following procedure with serrated connecting rods and flat connecting rods:
a. If the connecting rod cap is held in position with bolts and nuts, tighten the nuts to a
torque of 125 N·m (92 lb ft).
b. If the connecting rod cap is held in position with bolts, tighten the bolts to a torque of
155 N·m (114 lb ft).
13. Use the following procedure with hydraulically fractured connecting rods:
Note: Do not reuse the bolts. New bolts should be used.
a. Tighten the bolts to a torque of 70 N·m (52 lb ft).
b. Tighten the bolts for an additional 120 degrees.
14. Rotate the crankshaft in order to ensure that there is no binding.
15. Use Tooling (C) in order to check the height of the piston above the cylinder block. Refer to
Testing and Adjusting, "Piston Height - Inspect".
End By:
a. Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
b. Install the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Install".
c. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 28 23:28:14 UTC+0800 2020
3/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01463918
Connecting Rod Bearings - Remove
SMCS - 1219-011
Removal Procedure
Start By:
A. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00550759
Typical example
1. Remove bolt (2) and two bolts (1) that hold the engine oil relief valve in position.
2. Remove the engine oil relief valve in order to gain access to the connecting rods.
3. Remove two bolts (4) that fasten the oil line to the engine oil pump. Remove bolt (3) that
holds the oil strainer in position.
4. Remove the oil strainer and the oil line in order to gain access to the connecting rods.
5. In order to remove the connecting rod caps, turn the crankshaft in a clockwise direction until
the piston is at the bottom center position.
Illustration 2 g00551183
2/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Type A connecting rod.
Illustration 3 g00551189
Type B connecting rod.
Note: There are two types of connecting rods that may be used in the engine. Type A
connecting rods have serrated mating faces on the connecting rod and the connecting rod
cap. Type A connecting rods are held together with a through bolt and a nut. Type B
connecting rods have an alignment pin in the connecting rod cap. Type B connecting rods
are held together with a bolt that is threaded into the connecting rod.
6. If you have Type A connecting rods, remove two nuts (9) and two bolts (10) that fasten the
connecting rod cap to the connecting rod. If you have Type B connecting rods, remove two
bolts (11) that fasten the connecting rod cap to the connecting rod.
7. Remove connecting rod cap (8) from the connecting rod.
8. Remove lower connecting rod bearing (5). Keep the connecting rod bearings together with
the respective connecting rod caps for installation purposes.
9. Carefully push the connecting rod into the cylinder liner in order to remove upper
connecting rod bearing (6). The connecting rod may need to be rotated in order to prevent
contact with the piston cooling jet.
10. Remove upper connecting rod bearing (6). Keep the connecting rod bearings together with
the respective connecting rods for installation purposes.
11. Repeat Steps 5 through 9 for the remaining connecting rod bearings.
Tue Jan 28 23:29:10 UTC+0800 2020
3/4
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
17. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01463939
Connecting Rod Bearings - Install
SMCS - 1219-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 1 g00551183
Type A connecting rod.
Illustration 2 g00551189
Type B connecting rod.
Note: There are two types of connecting rods that may be used in the engine. Type A
connecting rods have serrated mating faces on the connecting rod and the connecting rod
cap. Type A connecting rods are held together with a through bolt and a nut. Type B
connecting rods have an alignment pin in the connecting rod cap. Type B connecting rods
are held together with a bolt that is threaded into the connecting rod.
1. Clean the bearing surface of connecting rod (7) and connecting rod cap (8) .
2. Clean upper connecting rod bearing (6) and lubricate the bearing face with clean engine oil.
3. Clean lower connecting rod bearing (5) and lubricate the bearing face with clean engine oil.
Note: Align the tabs on the connecting rod bearings with the tab grooves in the connecting
rod.
4. Install upper connecting rod bearing (6) in connecting rod (7) .
5. Pull the connecting rod into position against the crankshaft. The connecting rod may need to
be rotated in order to prevent contact with the piston cooling jet.
6. Install lower connecting rod bearing (5) in connecting rod cap (8) .
7. Put connecting rod cap (8) in position on connecting rod (7). Ensure that the identification
numbers are stamped on the same side.
2/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 8. If you have Type A connecting rods, install two bolts (10) and two nuts (9) that fasten the
connecting rod cap to the connecting rod. Tighten the nuts for the connecting rod cap to a
torque of 125 N·m (92 lb ft). If you have Type B connecting rods, install two bolts (11) that
fasten the connecting rod cap to the connecting rod. Tighten the bolts for the connecting rod
cap to a torque of 155 N·m (114 lb ft).
9. Repeat Steps 1 through 8 for the remaining connecting rod bearings.
Illustration 3 g00550759
10. Put the oil line in position on the engine oil pump and install bolts (4). Install bolt (3) that
holds the oil strainer in position.
11. Put the engine oil relief valve in position on the engine and install two bolts (1) and bolt
(2) .
End By: Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan -
Remove and Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Tue Jan 28 23:30:07 UTC+0800 2020
3/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 307 EXCAVATOR 2WM
Configuration: 307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01758964
Crankshaft Main Bearings - Remove
SMCS - 1203-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6282 Torque Wrench Extension 1
Start By:
a. Remove the engine oil relief valve and the oil strainer. Refer to Disassembly and Assembly,
"Engine Oil Relief Valve - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Remove the following components from the engine in order to remove the rear main
bearing with the crankshaft in position: flywheel, flywheel housing, rear oil seal housing and
bridge assembly.
Note: Use Tooling (A) in order to remove the front main bearing cap with the front housing and
the engine oil pump in place. If Tooling (A) is not available, removal of the front cover and the
engine oil pump will be necessary. The engine oil pump is attached to the front main bearing cap.
1/3
307 EXCAVATOR 2WM00001-00499 (MACHINE) POWERED BY 3054 ENGINE(...
2020/1/28
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...