This document provides instructions for removing and installing the camshaft on a 3054 engine. It describes:
1) Removing the rocker shaft, pushrods, fuel transfer pump, and front housing before removing the camshaft.
2) Turning the engine upside down, removing the thrust washer and carefully removing the camshaft.
3) Cleaning and lubricating the camshaft prior to installation and carefully reinstalling it along with the thrust washer.
The document provides instructions for removing and installing various engine components, including:
1) Lifter group removal which requires removing the camshaft first. Mark lifters for correct installation.
2) Camshaft removal requiring removal of other components first. Carefully remove camshaft while avoiding damage.
3) Engine oil pan removal requiring keeping parts clean to avoid contamination and containing fluids for proper disposal.
The document provides instructions for removing and installing camshaft bearings on a 3054 engine. It lists the required tools which include a camshaft bearing tool group and a ratchet wrench. The removal procedure involves first removing the camshaft according to separate instructions. To remove each bearing, a camshaft bearing tool is inserted and the bearing is pressed off the front housing. New bearings are pressed into place during installation. The camshaft and any other removed components are then reinstalled.
The document provides instructions for removing and installing camshaft bearings on a 3054 engine. It lists the required tools which include a camshaft bearing tool group and a ratchet wrench. The removal procedure involves first removing the camshaft according to separate instructions. To remove each bearing, a camshaft bearing tool is inserted and the bearing is pulled out. For installation, each bearing is pressed into place using the camshaft bearing tool.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Proper alignment of thrust washers is emphasized.
- Camshaft bearings, using a camshaft bearing tool to remove and install bearings, ensuring oil hole alignment.
- The camshaft gear, requiring alignment of timing marks and use of a puller tool.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning the bearings and lubricating them with oil before reinstalling them using the camshaft bearing tool. Proper cleaning and lubrication are emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters from an excavator engine, using a telescoping magnet tool.
- A camshaft from the engine, noting to keep parts clean and align dowels.
- Camshaft bearings from the engine block using a bearing tool.
- An engine oil pan from the engine, noting to contain fluids for proper disposal.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and safety notices. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning and lubricating the bearings before reinstalling them and the camshaft. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and ensuring they are marked for correct installation.
- A camshaft, requiring removal of other components first, with care taken to avoid damage when removing and installing the camshaft.
- Camshaft bearings, using a special tool to remove worn bearings and ensuring oil holes are correctly aligned during installation.
- An engine oil pan, noting the need to contain fluids during removal and dispose of them properly.
The document provides instructions for removing and installing various engine components, including:
1) Lifter group removal which requires removing the camshaft first. Mark lifters for correct installation.
2) Camshaft removal requiring removal of other components first. Carefully remove camshaft while avoiding damage.
3) Engine oil pan removal requiring keeping parts clean to avoid contamination and containing fluids for proper disposal.
The document provides instructions for removing and installing camshaft bearings on a 3054 engine. It lists the required tools which include a camshaft bearing tool group and a ratchet wrench. The removal procedure involves first removing the camshaft according to separate instructions. To remove each bearing, a camshaft bearing tool is inserted and the bearing is pressed off the front housing. New bearings are pressed into place during installation. The camshaft and any other removed components are then reinstalled.
The document provides instructions for removing and installing camshaft bearings on a 3054 engine. It lists the required tools which include a camshaft bearing tool group and a ratchet wrench. The removal procedure involves first removing the camshaft according to separate instructions. To remove each bearing, a camshaft bearing tool is inserted and the bearing is pulled out. For installation, each bearing is pressed into place using the camshaft bearing tool.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Proper alignment of thrust washers is emphasized.
- Camshaft bearings, using a camshaft bearing tool to remove and install bearings, ensuring oil hole alignment.
- The camshaft gear, requiring alignment of timing marks and use of a puller tool.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It begins by listing the required tools. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning the bearings and lubricating them with oil before reinstalling them using the camshaft bearing tool. Proper cleaning and lubrication are emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters from an excavator engine, using a telescoping magnet tool.
- A camshaft from the engine, noting to keep parts clean and align dowels.
- Camshaft bearings from the engine block using a bearing tool.
- An engine oil pan from the engine, noting to contain fluids for proper disposal.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and safety notices. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning and lubricating the bearings before reinstalling them and the camshaft. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and ensuring they are marked for correct installation.
- A camshaft, requiring removal of other components first, with care taken to avoid damage when removing and installing the camshaft.
- Camshaft bearings, using a special tool to remove worn bearings and ensuring oil holes are correctly aligned during installation.
- An engine oil pan, noting the need to contain fluids during removal and dispose of them properly.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and safety notices. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning and lubricating the bearings before reinstalling them and the camshaft. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and gives step-by-step procedures. The removal process involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. For installation, each bearing is pressed into place in the block and lubricated before reinstalling the camshaft. Proper cleaning and lubrication are emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Proper alignment of thrust washers is emphasized.
- Camshaft bearings, using a camshaft bearing tool to remove and install bearings, ensuring oil hole alignment.
- The camshaft gear, requiring alignment of timing marks and use of a puller tool.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and reinstalled ensuring correct cylinder numbering.
- The camshaft, which is removed after other components and installed lubricated and ensuring proper alignment of thrust washers and dowels.
- Camshaft bearings, which are inspected and removed/installed using a bearing tool to correctly align oil holes.
- The engine oil pan, with notices to contain fluids and properly dispose of them.
The document provides instructions for removing and installing various engine components, including:
- Lifters from an excavator engine, using a telescoping magnet tool.
- A camshaft from the engine, noting to keep parts clean and avoid damaging lobes or bearings.
- Camshaft bearings from the cylinder block, using a camshaft bearing tool.
- An engine oil pan from the excavator, noting to contain fluids and dispose of them properly.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and ensuring they are marked for correct installation.
- A camshaft, which is removed after other components and carefully installed, ensuring lobes and bearings are not damaged.
- Camshaft bearings, which are inspected and removed/installed using a bearing tool, ensuring oil holes are correctly aligned.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Precautions are listed to keep parts clean and avoid damage.
- Camshaft bearings, using a camshaft bearing tool and ensuring oil holes are aligned.
The summaries provide concise yet comprehensive overviews of the removal and installation procedures and safety precautions for the given engine components from the multi-page repair manual document.
Caterpillar Cat 312B L Excavator (Prefix 6SW) Service Repair Manual (6SW00001...jdkskmdmdm
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The summary is:
1) The procedure begins by removing components like the rocker shaft, pushrods, and front housing to access the camshaft.
2) To remove the camshaft, the thrust washer is taken off and the camshaft is carefully pulled from the engine.
3) Camshaft installation involves cleaning and lubricating the camshaft before carefully placing it back in the engine and replacing the thrust washer.
Caterpillar Cat 312B and 312B L Excavator (Prefix 6SW) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the camshaft, camshaft bearings, camshaft gear, and engine oil pan. The procedures describe draining fluids, using required tools, cleaning parts, and torquing bolts to specification. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 312B and 312B L Excavator (Prefix 6SW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The removal procedure involves removing other components like the rocker shaft and pushrods first. For the camshaft, the thrust washer is removed and the camshaft is carefully taken out. For installing, the camshaft is lubricated and positioned ensuring alignment. For the camshaft gear, timing marks are aligned and the gear is removed using a puller. Installation involves aligning the timing marks and ensuring proper backlash. Removal and installation of camshaft bearings and the engine oil pan are also described.
Caterpillar Cat 312B L Excavator (Prefix 6SW) Service Repair Manual (6SW00001...f8usejkddmmd
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The removal procedure involves removing other components like the rocker shaft and pushrods first. For the camshaft, the thrust washer is removed and the camshaft is carefully taken out. For installing, the camshaft is lubricated and positioned ensuring alignment. For the camshaft gear, timing marks are aligned and the gear is removed using a puller. Installation involves aligning the timing marks and ensuring proper backlash. Removal and installation of camshaft bearings and the engine oil pan are also described.
Kubota M115GXDTC-4 Tractor Parts Catalogue Manual (Publishing ID BKIDK5251).pdfshuangminzou
This document provides a list of parts for frequently used items and components for a Kubota engine. It includes over 400 individual part numbers, part names in Polish and English, quantities, and other specifications. The parts include switches, fuses, bulbs, filters, belts, hoses, seals, and other routine maintenance items. Key components listed include the crankcase, oil pan, cylinder head, and brackets. Quantities and remarks provide additional details on serial numbers, weights, amperage, and other technical specifications.
Kubota L4630DT-C GST-C Tractor Parts Catalogue Manual (Publishing ID BKIDK05...shuangminzou
This document lists frequently used parts for a Kubota 30DT-C/GST-C tractor. It includes 170 parts such as fuses, light bulbs, filters, switches, hoses, and other common replacement components. Key information provided for each part includes the part number, name, quantity used, and weight. Notes indicate when new parts should be ordered and updated part numbers.
Kubota L2501DT Tractor Parts Catalogue Manual (Publishing ID BKIDK5230).pdfshuangminzou
The document is a parts list for frequently used items on a piece of machinery. It includes 30 parts ranging from switches and fuses to filters and hoses. For each part it provides the part number, name in Polish and English, quantity used, and other identifying information like serial number or weight.
Kubota KX41-2S KX41-2SV Excavator Parts Catalogue Manual (Publishing ID BKID...shuangminzou
This document contains a parts list for a crankcase assembly. It includes 230 parts ranging from gaskets and plugs to larger components like the crankshaft and cylinder head. Each part is listed with its part number, name in Polish and English, quantity used, and weight. Tolerances or size variations are specified for some parts like bearing shells.
Kubota G2160EC-2 Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK50...shuangminzou
This document provides a parts list for an engine, listing part numbers, part names in Polish and English, quantities, serial numbers/pins, weights, and remarks for each part. It includes sections for the crankcase, oil pan, cylinder head, gear case, head cover, oil filter, oil gauge, oil pump, and main bearing case. Each section lists the relevant parts in a table format.
Kubota G261-HD Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK5350...shuangminzou
This document contains a list of parts for a Kubota engine. It includes 200 items ranging from starters, switches, filters, hoses, bolts, and other engine components. Each item lists the part number, name in Polish and English, quantity needed, and other identifying information. It appears to be providing an exhaustive list of parts that make up the engine for maintenance or repair purposes.
Kubota G21LD Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK0654).pdfshuangminzou
This document provides a parts list for a crankcase assembly, including 140 parts ranging from crankcases and caps to pins, plugs, seals, and gaskets. It lists the part numbers, names in Polish and English, quantities, identification codes, weights, and remarks for each part. The parts list is separated into sections for the crankcase, oil pan, cylinder head, gear case, and head covers with different identification code ranges. It was last updated on August 18, 2016 and contains copyright information for Kubota Corporation.
Kubota F3090-EU Front Mower Parts Catalogue Manual (Publishing ID BKIDA5063).pdfshuangminzou
This document provides a list of frequently used parts for a piece of equipment. It includes 160 parts with information like part number, name, quantity, serial number, weight, and remarks. The parts are for systems like the starter switch, thermostat, filters, belts, hoses, seals, and more. Specifications like part number, weight, and serial number ranges are provided to ensure the correct part is identified.
Kubota B2400D Tractor Parts Catalogue Manual (Publishing ID BKIDK0095).pdfshuangminzou
This document provides a parts list for the crankcase (Kurbelgehäuse) of a Kubota B2400D engine. It lists 23 parts related to the crankcase, including the composite crankcase, caps, plugs, pins, bushings, and an oil pressure switch. Each part is identified by number, part name in Polish and English, quantity, serial number if applicable, and weight in kilograms. Tolerances or serial number ranges are indicated for some parts. The document contains several copyright notices and was last updated on 04-03-2020.
Kubota B2230D Tractor Parts Catalogue Manual (Publishing ID BKIDK0597).pdfshuangminzou
This document provides a parts list for a gear case assembly with part numbers, names, quantities, serial numbers, and other specifications. It includes over 30 individual part listings for components of the gear case like bolts, plugs, seals, springs, and the gear case housing itself. The parts are specified for a Kubota engine model 230D gear case with serial numbers less than or greater than certain values.
Kubota B1181DT-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5130).pdfshuangminzou
This document provides a parts list for frequently used items on a Kubota 181DT-EC excavator. It includes 30 parts ranging from switches and fuses to hoses, filters, and other components. Each part is listed with the part number, name in Polish and English, quantity, and other identifying information.
More Related Content
Similar to Caterpillar Cat 315 Excavator (Prefix 3ZM) Service Repair Manual (3ZM00001 and up).pdf
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and safety notices. The removal procedure involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. The installation procedure specifies cleaning and lubricating the bearings before reinstalling them and the camshaft. Proper cleaning and lubrication of parts is emphasized to prevent premature wear.
This document provides instructions for removing and installing camshaft bearings on a 3054 engine. It outlines the required tools and gives step-by-step procedures. The removal process involves first removing the camshaft and then using a camshaft bearing tool and ratchet wrench to pull each bearing out of the engine block. For installation, each bearing is pressed into place in the block and lubricated before reinstalling the camshaft. Proper cleaning and lubrication are emphasized to prevent premature wear.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Proper alignment of thrust washers is emphasized.
- Camshaft bearings, using a camshaft bearing tool to remove and install bearings, ensuring oil hole alignment.
- The camshaft gear, requiring alignment of timing marks and use of a puller tool.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and reinstalled ensuring correct cylinder numbering.
- The camshaft, which is removed after other components and installed lubricated and ensuring proper alignment of thrust washers and dowels.
- Camshaft bearings, which are inspected and removed/installed using a bearing tool to correctly align oil holes.
- The engine oil pan, with notices to contain fluids and properly dispose of them.
The document provides instructions for removing and installing various engine components, including:
- Lifters from an excavator engine, using a telescoping magnet tool.
- A camshaft from the engine, noting to keep parts clean and avoid damaging lobes or bearings.
- Camshaft bearings from the cylinder block, using a camshaft bearing tool.
- An engine oil pan from the excavator, noting to contain fluids and dispose of them properly.
The document provides instructions for removing and installing various engine components, including:
- Lifters, which are removed using a telescoping magnet and ensuring they are marked for correct installation.
- A camshaft, which is removed after other components and carefully installed, ensuring lobes and bearings are not damaged.
- Camshaft bearings, which are inspected and removed/installed using a bearing tool, ensuring oil holes are correctly aligned.
The document provides instructions for removing and installing various engine components, including:
- Lifters, requiring the use of a telescoping magnet tool.
- The camshaft, which must be removed before removing lifters. Precautions are listed to keep parts clean and avoid damage.
- Camshaft bearings, using a camshaft bearing tool and ensuring oil holes are aligned.
The summaries provide concise yet comprehensive overviews of the removal and installation procedures and safety precautions for the given engine components from the multi-page repair manual document.
Caterpillar Cat 312B L Excavator (Prefix 6SW) Service Repair Manual (6SW00001...jdkskmdmdm
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The summary is:
1) The procedure begins by removing components like the rocker shaft, pushrods, and front housing to access the camshaft.
2) To remove the camshaft, the thrust washer is taken off and the camshaft is carefully pulled from the engine.
3) Camshaft installation involves cleaning and lubricating the camshaft before carefully placing it back in the engine and replacing the thrust washer.
Caterpillar Cat 312B and 312B L Excavator (Prefix 6SW) Service Repair Manual ...fujkskemdmdm4r
This document provides instructions for removing and installing various engine components on a Caterpillar 3054 engine, including the camshaft, camshaft bearings, camshaft gear, and engine oil pan. The procedures describe draining fluids, using required tools, cleaning parts, and torquing bolts to specification. Cautions are provided regarding containing fluids and preventing contamination.
Caterpillar Cat 312B and 312B L Excavator (Prefix 6SW) Service Repair Manual ...fskekkdmdmdm3e
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The removal procedure involves removing other components like the rocker shaft and pushrods first. For the camshaft, the thrust washer is removed and the camshaft is carefully taken out. For installing, the camshaft is lubricated and positioned ensuring alignment. For the camshaft gear, timing marks are aligned and the gear is removed using a puller. Installation involves aligning the timing marks and ensuring proper backlash. Removal and installation of camshaft bearings and the engine oil pan are also described.
Caterpillar Cat 312B L Excavator (Prefix 6SW) Service Repair Manual (6SW00001...f8usejkddmmd
This document provides instructions for removing and installing a camshaft and camshaft gear on a Caterpillar 3054 engine. The removal procedure involves removing other components like the rocker shaft and pushrods first. For the camshaft, the thrust washer is removed and the camshaft is carefully taken out. For installing, the camshaft is lubricated and positioned ensuring alignment. For the camshaft gear, timing marks are aligned and the gear is removed using a puller. Installation involves aligning the timing marks and ensuring proper backlash. Removal and installation of camshaft bearings and the engine oil pan are also described.
Similar to Caterpillar Cat 315 Excavator (Prefix 3ZM) Service Repair Manual (3ZM00001 and up).pdf (11)
Kubota M115GXDTC-4 Tractor Parts Catalogue Manual (Publishing ID BKIDK5251).pdfshuangminzou
This document provides a list of parts for frequently used items and components for a Kubota engine. It includes over 400 individual part numbers, part names in Polish and English, quantities, and other specifications. The parts include switches, fuses, bulbs, filters, belts, hoses, seals, and other routine maintenance items. Key components listed include the crankcase, oil pan, cylinder head, and brackets. Quantities and remarks provide additional details on serial numbers, weights, amperage, and other technical specifications.
Kubota L4630DT-C GST-C Tractor Parts Catalogue Manual (Publishing ID BKIDK05...shuangminzou
This document lists frequently used parts for a Kubota 30DT-C/GST-C tractor. It includes 170 parts such as fuses, light bulbs, filters, switches, hoses, and other common replacement components. Key information provided for each part includes the part number, name, quantity used, and weight. Notes indicate when new parts should be ordered and updated part numbers.
Kubota L2501DT Tractor Parts Catalogue Manual (Publishing ID BKIDK5230).pdfshuangminzou
The document is a parts list for frequently used items on a piece of machinery. It includes 30 parts ranging from switches and fuses to filters and hoses. For each part it provides the part number, name in Polish and English, quantity used, and other identifying information like serial number or weight.
Kubota KX41-2S KX41-2SV Excavator Parts Catalogue Manual (Publishing ID BKID...shuangminzou
This document contains a parts list for a crankcase assembly. It includes 230 parts ranging from gaskets and plugs to larger components like the crankshaft and cylinder head. Each part is listed with its part number, name in Polish and English, quantity used, and weight. Tolerances or size variations are specified for some parts like bearing shells.
Kubota G2160EC-2 Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK50...shuangminzou
This document provides a parts list for an engine, listing part numbers, part names in Polish and English, quantities, serial numbers/pins, weights, and remarks for each part. It includes sections for the crankcase, oil pan, cylinder head, gear case, head cover, oil filter, oil gauge, oil pump, and main bearing case. Each section lists the relevant parts in a table format.
Kubota G261-HD Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK5350...shuangminzou
This document contains a list of parts for a Kubota engine. It includes 200 items ranging from starters, switches, filters, hoses, bolts, and other engine components. Each item lists the part number, name in Polish and English, quantity needed, and other identifying information. It appears to be providing an exhaustive list of parts that make up the engine for maintenance or repair purposes.
Kubota G21LD Garden Tractor Parts Catalogue Manual (Publishing ID BKIDK0654).pdfshuangminzou
This document provides a parts list for a crankcase assembly, including 140 parts ranging from crankcases and caps to pins, plugs, seals, and gaskets. It lists the part numbers, names in Polish and English, quantities, identification codes, weights, and remarks for each part. The parts list is separated into sections for the crankcase, oil pan, cylinder head, gear case, and head covers with different identification code ranges. It was last updated on August 18, 2016 and contains copyright information for Kubota Corporation.
Kubota F3090-EU Front Mower Parts Catalogue Manual (Publishing ID BKIDA5063).pdfshuangminzou
This document provides a list of frequently used parts for a piece of equipment. It includes 160 parts with information like part number, name, quantity, serial number, weight, and remarks. The parts are for systems like the starter switch, thermostat, filters, belts, hoses, seals, and more. Specifications like part number, weight, and serial number ranges are provided to ensure the correct part is identified.
Kubota B2400D Tractor Parts Catalogue Manual (Publishing ID BKIDK0095).pdfshuangminzou
This document provides a parts list for the crankcase (Kurbelgehäuse) of a Kubota B2400D engine. It lists 23 parts related to the crankcase, including the composite crankcase, caps, plugs, pins, bushings, and an oil pressure switch. Each part is identified by number, part name in Polish and English, quantity, serial number if applicable, and weight in kilograms. Tolerances or serial number ranges are indicated for some parts. The document contains several copyright notices and was last updated on 04-03-2020.
Kubota B2230D Tractor Parts Catalogue Manual (Publishing ID BKIDK0597).pdfshuangminzou
This document provides a parts list for a gear case assembly with part numbers, names, quantities, serial numbers, and other specifications. It includes over 30 individual part listings for components of the gear case like bolts, plugs, seals, springs, and the gear case housing itself. The parts are specified for a Kubota engine model 230D gear case with serial numbers less than or greater than certain values.
Kubota B1181DT-EC Tractor Parts Catalogue Manual (Publishing ID BKIDA5130).pdfshuangminzou
This document provides a parts list for frequently used items on a Kubota 181DT-EC excavator. It includes 30 parts ranging from switches and fuses to hoses, filters, and other components. Each part is listed with the part number, name in Polish and English, quantity, and other identifying information.
Kubota B1181D-F2-EC-S5 Tractor Parts Catalogue Manual (Publishing ID BKIDA515...shuangminzou
This document provides a parts list for the main bearing case of an engine. It includes the part numbers, names, quantities, and other details for 110 unique parts that make up the main bearing case assembly. The parts are grouped into categories like bearings, seals, bolts, and covers. The main bearing case assembly comprises these various individual components.
JCB 300T TRACKED Robot Parts Catalogue Manual (Serial Number 02427501-024278...shuangminzou
This document contains parts catalogs and diagrams for hydraulic components for an agricultural construction vehicle. It includes lists of parts with descriptions and quantities for hydraulic circuits, pumps, motors, tubing, valves, filters and other components. Multiple pages of detailed parts information are provided for the transmission, pilot controls, bulkhead plates, accumulators and other hydraulic systems.
This document provides instructions to disassemble and assemble the final drive of a D9R track-type tractor. The disassembly process involves using various tools to remove over 30 components from the planetary carrier, sun gear, hub, and ring gear. The assembly process reverses the disassembly steps, heating some bearings before installation and using specialty tools to install seals and retainers. Proper safety precautions and inspection of parts is emphasized throughout.
This document provides instructions for disassembling and assembling the recoil cylinder of a D7E track-type tractor. The disassembly process involves removing 21 different parts from the cylinder including the head assembly, piston assembly, seals, rings, and manifold. The assembly process describes installing these 21 parts in the reverse order and includes lubricating seals with hydraulic oil additive. Safety precautions are provided to avoid injury from the high-pressure parts.
This document provides instructions for removing and installing various components of the front gear group, front housing, valve mechanism cover, and valve mechanism cover base of a Caterpillar 3412E engine used in a 992C wheel loader. The procedures include removing gears, shafts, housings, covers, and electrical harness assemblies. Special tools may be required and components must be kept clean to prevent premature wear. Torque specifications are provided for reinstallation.
The document provides instructions for disassembling and assembling the piston pump and gear pump used in the secondary steering system of a 990K wheel loader. The piston pump assembly procedure involves 40 steps to remove housing covers, shafts, seals, pistons, springs and other internal components. The gear pump removal involves draining oil and disconnecting hoses to remove the pump. Its disassembly requires removing bolts and washers to separate the pump body from other components.
The document provides instructions for removing and installing various engine components of a 3406C diesel engine, including the cylinder head assembly, spacer plate, valves, valve guides, oil pan, and plate. The removal process involves draining oil, removing mounting bolts, lifting components, and extracting seals and gaskets. The installation process specifies cleaning surfaces, inserting new seals and gaskets, lowering components into place, and tightening bolts in a specific sequence while applying lubricant.
1) The document provides instructions for disassembling and assembling the governor component of a 3204 vehicular engine used in Caterpillar 953 track loaders.
2) The disassembly instructions include removing the fuel injection pump housing, governor housing cover, adjustment screws, lever assembly, torque control group, and weight assembly.
3) The assembly instructions list installing these components in reverse order and adjusting clearance measurements and spring tensions as specified.
This document provides disassembly and assembly instructions for a governor for a 3204 vehicular engine used in 943 and 953 track-type loaders. It describes removing and installing over 40 individual parts in 37 steps for disassembly and 33 steps for assembly, including removing the fuel injection pump housing, governor components like springs, pins, and levers, and reinstalling them in the reverse order. Precise instructions are given to disassemble and reassemble small intricate parts like ensuring proper end play of flyweights on dowels during assembly.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Caterpillar Cat 315 Excavator (Prefix 3ZM) Service Repair Manual (3ZM00001 and up).pdf
1. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01164529
Camshaft - Remove and Install
SMCS - 1210-010
Removal Procedure
Start By:
A. Remove the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Remove".
B. Remove the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Remove".
C. Remove the front housing. Refer to Disassembly and Assembly, "Housing (Front) -
Remove".
D. Remove the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
2. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Turn the engine upside-down so the valve lifters are held in a position away from the
camshaft.
Illustration 1 g00546803
2. Remove thrust washer (1). Make a note of the location of the hollow dowel (X) for
installation purposes.
Illustration 2 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
2/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 3. Carefully remove camshaft (2) from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00546869
NOTICE
Do not damage the lobes or the bearings when the camshaft is removed
or installed.
Note: Ensure that camshaft (2) is clean. Lubricate camshaft (2) with clean engine oil prior
to installation.
1. Carefully install camshaft (2) in the engine.
3/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 4 g00546803
2. Put thrust washer (1) in position. Make sure that thrust washer (1) is aligned with hollow
dowel (X) .
End By:
a. Install the camshaft gear. Refer to Disassembly and Assembly, "Camshaft Gear - Remove
and Install".
b. Install the front housing. Refer to Disassembly and Assembly, "Housing (Front) - Install".
c. Install the fuel transfer pump. Refer to Disassembly and Assembly, "Fuel Transfer Pump -
Install".
d. Install the rocker shaft and the pushrods. Refer to Disassembly and Assembly, "Rocker
Shaft and Pushrods - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:06:18 UTC+0800 2021
4/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i03140046
Camshaft Gear - Remove and Install
SMCS - 1210-010-GE
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Name Qty
A
1U-6671 Puller Gp 1
8S-4712 Bolt 2
1P-0510 Driver Group 1
Start By:
a. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
b. Remove the front cover. Refer to Disassembly and Assembly, "Front Cover - Remove".
1/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 1 g00541128
1. Rotate the crankshaft until the timing marks on the crankshaft gear, the camshaft gear, and
the fuel injection pump gear are aligned, as shown.
Note: The timing marks on the idler gear may not be aligned. This is caused by the
difference in the speed of the rotation of the idler gear.
Illustration 2 g00541130
2. Remove bolt (1) and the washer from the camshaft gear (2).
2/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 3 g00541131
3. Install Tooling (A) and remove camshaft gear.
Note: Do not lose the key from the camshaft gear.
4. Inspect the camshaft gear for wear and damage. Replace the gear, if necessary.
Installation Procedure
Illustration 4 g00541130
1. Install camshaft gear (2) in the front housing.
Note: When you install the camshaft gear, ensure that the teeth that have the timing marks
are facing toward the front. Also, ensure that the key is aligned properly in the keyway. If
necessary, tap the gear with a soft hammer in order to seat the key in the keyway.
2. If necessary, remove the idler gear in order to align the gear teeth correctly.
3. Install the washer and bolt (1) on the camshaft gear. Tighten bolt (1) to a torque of 95 N·m
(70 lb ft).
Note: Ensure that the timing marks on the camshaft gear, the crankshaft gear, and the fuel
injection pump gear are aligned.
3/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. 4. If a new camshaft gear is used, check the backlash of the camshaft gear. The minimum
backlash for a new gear is 0.08 mm (0.003 inch).
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Front Cover - Install".
b. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:07:14 UTC+0800 2021
4/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i06043534
Camshaft Bearings - Remove and Install
SMCS - 1211-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
Start By:
A. If the engine is equipped with a balancer, remove the balancer. Refer to Disassembly and
Assembly, "Balancer - Remove". If the engine is not equipped with a balancer, remove the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Remove" for the
correct procedure.
B. Remove the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and
Install" for the correct procedure.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 1 g01270437
1. Inspect camshaft bearing (1) . Refer to Specifications, "Camshaft Bearings" for more
information.
2. For worn or damaged camshaft bearing (1) use Tooling (A) in order to remove the camshaft
bearing from the cylinder block.
Note: Remove the camshaft bearing from the front of the cylinder block.
Installation Procedure
Table 2
Required Tools
Tool Part Number Part Description Qty
A
8S-2241 Camshaft Bearing Tool Group 1
8H-0684 Ratchet Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Clean the bearing housing in the cylinder block. Ensure that the oil holes in the bearing
housing are free from debris.
2/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 2 g01266512
2. Lubricate the bearing housing in the cylinder block with clean engine oil.
3. Accurately align two Oil Holes (X) in camshaft bearing (1) with the two oil holes in the
cylinder block.
Note: Groove (Y) in the camshaft bearing must be to the top of the cylinder block.
4. Use Tooling (A) in order to install camshaft bearing (1) into the cylinder block. Install the
camshaft bearing so that the front edge of the bearing is flush with the face of the recess in
the cylinder block.
Note: Ensure that all oil holes are correctly aligned. If the oils are not correctly aligned, the
camshaft bearing should be removed.
End By:
a. Install the camshaft. Refer to Disassembly and Assembly, "Camshaft - Remove and Install"
for the correct procedure.
b. If the engine is equipped with a balancer, install the balancer. Refer to Disassembly and
Assembly, "Balancer - Install". If the engine is not equipped with a balancer, install the
engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump - Install" for the
correct procedure.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:08:10 UTC+0800 2021
3/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02974660
Engine Oil Pan - Remove and Install
SMCS - 1302-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g01870497
Typical Example
2/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 2 g01871553
Note: The engine may be equipped with an oil drain plug or the engine may be equipped
with a drain valve.
1. If equipped, remove drain plug (2) and the O-ring seal. If equipped, open drain valve (5) by
turning handle (6) counterclockwise. Drain the engine oil into a suitable container for
storage or disposal.
2. If necessary, remove drain valve (5) from adapter (7) . If necessary, remove adapter (7)
from engine oil pan (3) .
Note: In order to remove a oil pan, the engine must be removed from the machine.
3. Remove bolts (1) from engine oil pan (3) .
4. Remove engine oil pan (3) and gasket (4) .
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
3/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. 1. Clean the gasket surfaces of the cylinder block and the engine oil pan thoroughly.
Illustration 3 g01870497
Typical Example
4/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 4 g01871553
2. Install a new gasket (4) to the cylinder block. Install engine oil pan (3) .
3. Install bolts (1) . Tighten bolts to a torque of 22 N·m (16 lb ft).
Note: The engine may be equipped with an oil drain plug or the engine may be equipped
with a drain valve.
4. If drain valve (5) and adapter (7) were removed, use the following procedure.
a. Install a new O-ring to the adapter (7) .
b. Install adapter (7) into engine oil pan (3) . Tighten the adapter to a torque of 34 N·m
(25 lb ft).
c. Install a new O-ring to drain valve (5) .
d. Install drain valve (5) into adapter (7) . Tighten the drain valve to a torque of 34 N·m
(25 lb ft).
5. If equipped, install a new O-ring seal on drain plug (2) . Install the drain plug. Tighten the
drain plug to a torque of 34 N·m (25 lb ft). If equipped, close drain valve (5) by turning
handle (6) clockwise. Turn handle (6) until the handle is tight. Do not overtighten the
handle.
6. Fill the engine oil pan to the correct level that is indicated on the engine oil level gauge.
5/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Note: Refer to the Operation and Maintenance Manual, "Refill Capacities" for the correct
engine oil capacity.
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:09:05 UTC+0800 2021
6/6
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i04368112
Cylinder Liner - Remove
SMCS - 1216-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1A-1460 Bolt 3
2J-3507 Full Nut 1
5F-7347 Head 1
5H-1504 Hard Washer 1
5P-8245 Washer 3
6V-2183 Screw 1
8H-0684 Ratchet Wrench 1
9U-6234 Puller Plate 1
9U-6281 Leg 3
1D-5119 Nut 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
B. Remove the pistons and connecting rods. Refer to Disassembly and Assembly, "Pistons and
Connecting Rods - Remove".
1/2
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. C. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Before you proceed with the removal of the cylinder liner, check the cylinder liners for wear
or for damage. Check the inner diameter of each cylinder liner at the top, the middle, and the
bottom. Check the inner diameter at two places that are 180 degrees away from each other. The
maximum wear for the cylinder liners is 0.25 mm (.010 inch).
Note: An engine may have a high rate of oil consumption if the surface of the cylinder liners are
glazed. Glaze can be removed from the cylinder liners by honing the bore of the cylinder liner.
1. Rotate the crankshaft in order to gain access to the cylinder liner. Place a protective cover
on the crankshaft in order to prevent damage.
Illustration 1 g00893799
2. Install Tooling (A) .
3. Remove cylinder liner (1) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:10:01 UTC+0800 2021
2/2
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01746068
Cylinder Liner - Install
SMCS - 1216-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
1A-1460 Bolt 3
2J-3507 Full Nut 1
5F-7347 Head 1
5H-1504 Hard Washer 1
5P-8245 Washer 1
6V-2183 Screw 1
8H-0684 Ratchet Wrench 1
9U-6235 Puller Plate 1
1U-9895 Cross Block 1
B 8T-0455 Liner Projection Tool Group 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 1. Clean the cylinder block bore with 8T-9011 Component Cleaner before you install the
cylinder liner.
2. Apply clean engine oil to the cylinder block bore. Do not apply the clean engine oil to the
top 50.0 mm (2.00 inch) of the cylinder block bore.
Illustration 1 g00635369
3. Install Tooling (A).
4. Install cylinder liner (1).
5. Press cylinder liner (1) into the cylinder block within 50.0 mm (2.00 inch) of the top of the
cylinder block.
Note: Cylinder liner (1) is a press fit to a distance of ±0.03 mm (±0.001 inch) from the top
of the cylinder block.
6. Apply 6V-1541 Quick Cure Primer to the exposed area of cylinder liner (1). Also apply 9S-
3265 Compound to the exposed area of cylinder liner (1).
7. Wipe off any excess compound from cylinder liner (1).
2/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g00635363
8. Use Tooling (B) to check that cylinder liner (1) is 0.10 mm (0.004 inch) above the cylinder
block or below the cylinder block.
9. Immediately after you install a new cylinder liner, follow the recommendations below:
a. Do not operate the engine at full load.
b. Do not operate the engine at high speed.
c. Do not allow the engine to run at low idle for an extended period of time.
End By:
a. Install the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Install".
b. Install the pistons and connecting rods. Refer to Disassembly and Assembly, "Piston and
Connecting Rods - Install".
c. Install the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head - Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:10:57 UTC+0800 2021
3/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i01548436
Piston Cooling Jets - Remove and Install
SMCS - 1331-010
Removal Procedure
Start By:
a. Remove the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Note: The naturally aspirated 3054 marine engine has one piston cooling jet that is located inside
the number one cylinder. The naturally aspirated 3056 marine engine is not equipped with piston
cooling jets.
Illustration 1 g00548374
Illustration 2 g00606467
1. Remove valve assembly (1) from piston cooling jet (2).
2. Remove piston cooling jet (2) from the cylinder block.
Note: The engine crankshaft may be rotated in order to access all of the piston cooling jets.
Note: Ensure that the ball moves freely within the valve assembly of the piston cooling jet.
Check that the tube of the piston cooling jet is not damaged.
3. Remove hollow dowel (3) from the cylinder block.
Note: Hollow dowel (3) is used to locate the piston cooling jet.
2/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. 4. Repeat Steps 1 through 3 for the removal of the remaining piston cooling jets.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00548374
Illustration 4 g00606467
1. Install piston cooling jet (2) to the cylinder block.
3/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Note: Ensure that piston cooling jet (2) is properly located on hollow dowel (3). Refer to the
Specifications Manual, "Piston Cooling Jet" for the correct procedure for the alignment of
the piston cooling jet.
2. Install valve assembly (1) into the piston cooling jet (2). Tighten the banjo bolt of the valve
assembly (1) to a torque of 20 N·m (15 lb ft).
3. Repeat Steps 1 through 2 for the installation of the remaining piston cooling jets.
End By:
a. Install the engine oil pan. Refer to Disassembly and Assembly, "Engine Oil Pan - Remove
and Install".
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:11:53 UTC+0800 2021
4/4
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02453078
Pistons and Connecting Rods - Remove
SMCS - 1225-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2269 Ridge Reamer 1
Start By:
A. Remove the cylinder head. Refer to Disassembly and Assembly, "Cylinder Head -
Remove".
B. Remove the engine oil pump. Refer to Disassembly and Assembly, "Engine Oil Pump -
Remove".
C. Remove the piston cooling jets. Refer to Disassembly and Assembly, "Piston Cooling Jets -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Use Tooling (A) to remove the liner wear ridge from the inner surface of the cylinder liner.
2. Position the two pistons that are being removed at the bottom center position.
1/2
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 1 g00550548
3. Remove nuts (1) and the bolts.
4. Remove connecting rod caps (2) and the connecting rod bearings. Keep connecting rod caps
(2) and the connecting rod bearings together for installation.
Illustration 2 g00550549
5. Push pistons (3) and the connecting rods out of the top of cylinder block (4) .
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:12:48 UTC+0800 2021
2/2
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Please write to us.
Our email:
aservicemanualpdf@yahoo.com
Please go to the homepage
to get the full manual, or
other brand PDF manuals.
Home Site:
aservicemanualpdf.com
30. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
GET MORE OTHER MANUALS https://www.aservicemanualpdf.com/
31. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 315-A EXCAVATOR 3ZM
Configuration: 315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine
Disassembly and Assembly
3054 Engine for Caterpillar Built Machines
Media Number -SENR6241-13 Publication Date -01/08/2008 Date Updated -04/08/2008
i02088687
Pistons and Connecting Rods - Disassemble
SMCS - 1225-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-6683 Ring Expander 1
B 1P-1857 Retaining Ring Pliers 1
Start By:
a. Remove the pistons and the connecting rods. Refer to Disassembly and Assembly, "Piston
and Connecting Rods - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 1 g00551459
Typical example
1. Use Tooling (A) in order to remove three piston rings (1) from piston (2).
Illustration 2 g00551460
Typical example
2. Use Tooling (B) in order to remove retaining rings (3) that hold the piston pin in position.
3. Remove piston pin (4) from the piston.
Note: If the piston pin cannot be removed by hand, heat the piston to a temperature of
45 ± 5 °C (113 ± 9 °F). Do not use a torch to heat the piston.
4. Remove bearing (5) from connecting rod (6).
2/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 3 g00893862
5. Use a suitable press and a suitable adapter in order to remove piston pin bushing (7) from
connecting rod (6).
Copyright 1993 - 2021 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Jan 11 23:13:44 UTC+0800 2021
3/3
315 Excavator 3ZM00001-UP (MACHINE) POWERED BY 3054 Engine(SEBP2354 ...
2021/1/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...