- The document provides instructions for installing the automatic timing advance on a 3306 engine.
- It describes using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt.
- Technicians are instructed to maintain constant torque on the automatic timing advance using a spanner wrench while tightening the bolt to the specified torque.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...xiapokang564341
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...hvy7sbkw8e
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...wenxian17880
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to lock the timing advance in place and tightening it to the specified torque. Technicians are instructed to keep parts clean and apply thread sealant to mounting studs during reinstallation.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...xiapokang564341
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...hvy7sbkw8e
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...wenxian17880
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to lock the timing advance in place and tightening it to the specified torque. Technicians are instructed to keep parts clean and apply thread sealant to mounting studs during reinstallation.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
More Related Content
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual Instant Download 1.pdf
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual Instant Download 1.pdf (20)
This document provides assembly instructions for a transmission in a 434E backhoe loader. It lists required tools and gives step-by-step instructions for assembling various transmission components, including the reverse shaft, input shaft, countershaft, and output shaft. Safety notes are included to warn of potential injury from improper assembly of spring-loaded parts.
The document provides instructions for removing and installing various components of a Caterpillar 992K wheel loader, including:
1) Removing and disassembling the rear power take-off, which involves using various tools to remove nuts, bearings, and other parts.
2) Instructions for reassembling the rear power take-off by installing bearings and other components in the reverse order of disassembly.
3) Procedures for removing and installing the vibration damper and pulley, which includes using guide studs and lifting equipment to handle the heavy components.
The document contains detailed step-by-step instructions along with illustrations to correctly perform maintenance on specific parts of the 992K
The document provides instructions for disassembling a transmission (power shift) from a 416E Backhoe Loader. It lists required tools and outlines 25 steps to remove the transmission, including draining fluids, disconnecting electrical and hydraulic connections, removing mounting hardware, and lifting the transmission off with a hydraulic jack. The transmission weighs approximately 255 kg (562 lb) and special care must be taken when handling it and containing any fluids.
This document provides instructions for removing and disassembling the transmission of a 416D Backhoe Loader. It outlines 14 steps to remove the transmission, which includes draining fluids, removing mounting bolts, and lowering the transmission. It then details disassembling the transmission into its major components, such as removing the front and rear output shafts, planetary gears, clutch packs, seals, and bearings. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing the sliding frame and bearings on a 434E backhoe loader. The key steps include:
1. Removing the swing frame, swing cylinders, and hydraulic lines.
2. Using lifting devices to remove the lift cylinders, link assembly, sliding frame, and various mounting bars and blocks.
3. Using pullers and drivers to remove the thrust bearings and sliding bearings from the sliding frame.
4. Reversing the removal procedures to install the new bearings and reassemble the sliding frame and associated components. Special tools and low bearing temperatures are required for installation.
The document provides instructions for removing and installing the fuel transfer pump on a Caterpillar 322N excavator powered by a 3116 engine. It details removing the pump cover, spring, piston and seals. It also describes inspecting parts and lubricating them with oil during installation. Installation involves reversing the removal steps and ensuring proper alignment of components.
The document provides instructions for removing and installing final drive sprockets, travel brake valves, and travel motors on a 322-A excavator model. Key steps include separating the track assemblies, using tools to support heavy components like the sprocket while removing fasteners, cleaning mating surfaces, replacing seals, and torquing fasteners to the specified values. The process also requires draining oil from the final drive and hydraulic system before removing components.
This document provides instructions for disassembling the control valve (auxiliary) on a 322C excavator. It describes removing and disassembling various components of the control valve such as solenoid valves, line relief valves, fittings, seals, and spools. Cleanliness is emphasized to prevent contamination of hydraulic systems during disassembly and reassembly. Detailed illustrations and part numbers are provided for each step. Personal protective equipment is recommended when removing or releasing parts under spring pressure.
Caterpillar Cat 322 L EXCAVATOR (Prefix 4RM) Service Repair Manual Instant Do...udjkskdmmd
This document provides instructions for removing and installing a governor from a 322 L, 322 LN, and 322 N excavator powered by a 3116 engine. The removal procedure involves using special tools to disconnect linkages and tubes connecting the governor to the engine. Individual parts like O-rings and seals must be removed and replaced. The installation procedure specifies lubricating new seals and using tools to reconnect everything in the reverse order of removal. Special attention is given to properly adjusting the fuel setting after installing the new governor.
Caterpillar Cat 322C L Hydraulic Excavator (Prefix EMR) Service Repair Manual...udjkskdmmd
The document provides instructions for removing and installing various engine components on a Caterpillar 3126B engine, including:
- Removing and installing the crankshaft vibration damper and pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing and installing the front cover.
- Removing and installing the front housing.
The summaries provide the high level steps for removing and installing the listed components from the 3126B engine in 3 sentences or less per the request.
The document provides instructions for removing and installing various components on a M317D2 Wheeled Excavator, including:
- Removing the swing gear and bearing by lifting it out after removing bolts and spacers.
- Installing the swing gear and bearing by positioning it with lifting tools, then installing bolts and spacers.
- Removing the hydraulic oil filter by taking off the cover, O-ring, and retainer, then removing the filter.
- Installing the hydraulic oil filter by reversing the removal steps.
- Removing the hydraulic tank by draining it, disconnecting hoses and fittings, and lifting it off after removing bolts.
- Installing the hydraulic tank by
This document provides instructions for removing and installing various engine components on a Caterpillar 993K wheel loader, including:
- Inlet and exhaust valves, guides, and seat inserts
- Engine oil filter base
- Engine oil cooler
The procedures describe using various tools to remove parts like the cylinder head, valves, guides, filters, hoses, and the oil cooler assembly. Installation is generally the reverse of removal, with instructions to clean parts, apply sealant or lubricant, and torque fasteners to the specified values. Safety notices warn of spring hazards and keeping parts clean to prevent wear.
This document provides instructions for removing and installing various components of the rear power take-off (RPTO) and vibration damper on a 993K wheel loader. It describes in detail how to disassemble the RPTO by removing nuts, bearings, and gears. It then explains the reverse process to assemble the RPTO. Separate sections provide procedures for installing the RPTO and removing/installing the vibration damper and pulley, including the use of various tools. Detailed illustrations accompany each step.
This document provides instructions for disassembling and assembling the parking brake on a Caterpillar 993K Wheel Loader. It describes removing 16 different components of the parking brake including pistons, springs, discs, plates, and housings. Detailed illustrations and torque specifications are provided for each step of disassembly and assembly. Tools required include a slide hammer, puller, driver group, link brackets, lever puller hoist, and sealant. Personnel safety warnings and proper procedures are noted throughout.
The document provides instructions for disassembling and assembling the torque converter of a 966F wheel loader. It describes 31 steps to disassemble the various components of the torque converter including removing housing bolts, gears, bearings, seals, and other parts. It then describes 26 steps for reassembling the torque converter components in reverse order, noting specific alignment and torque specifications. The overall document provides detailed technical instructions for maintenance personnel to fully disassemble and reassemble the machine's torque converter.
The document provides instructions for disassembling and assembling the service brake on a Caterpillar 993K wheel loader. The disassembly procedure involves removing reaction plates, discs, springs, pistons, seals and other brake components. The assembly procedure describes installing these components in reverse order and applying grease and torques as specified. Safety precautions are provided to prevent injury from spring forces.
The document provides instructions for servicing components of a Caterpillar 3306 engine, including:
- Installing and removing fuel injection nozzles
- Disassembling and assembling the fuel ratio control
- Removing and installing the fuel shutoff solenoid
The instructions include diagrams illustrating the components and numbered steps for disassembly, cleaning, inspection, and reassembly of the parts. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for disassembling and assembling the rear axle carrier, hubs, and brakes of an M318F wheeled excavator. It lists the required tools and parts and provides step-by-step instructions and illustrations for removing components like the carrier housing, planetary gears, and brake discs, and installing components like the thrust washer, carrier gear, and retaining rings. The instructions aim to properly remove and replace these components while containing fluids and following safety procedures.
This document provides instructions for disassembling and assembling the swing drive of a M325C MH wheeled excavator. It lists 31 steps for disassembly, removing components like the cover, carrier assembly, gears, shafts, and seals. It then lists 35 steps for assembly, installing these components in reverse order along with tools needed and special instructions. Precautions are given to contain fluids, clean parts thoroughly, and use lifting devices due to component weights up to 310 kg.
This document provides instructions for disassembling the front final drive, carrier, hubs, and brakes of an M320 Excavator. It outlines 28 steps to remove components like the planetary carrier, sun gear, ring gear, brake piston, hub, bearings and seals. Various tools are required including retaining ring pliers, pullers, wrenches and adapters. Safety notices are included about containing fluids, releasing hydraulic pressure and avoiding damage during disassembly.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 17:59:01 UTC+0800 2019
2/2
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 17:59:57 UTC+0800 2019
4/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the
surface of the fuel injection pump housing.
2/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 18:01:48 UTC+0800 2019
6/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
Illustration 9 g00589938
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil
drain line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil
drain line (25) and install the bolts. Install the clamps on the oil line.
Illustration 10 g00460346
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 ± 7 N·m (20 ± 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 18:02:44 UTC+0800 2019
6/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
27. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...