This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the starting motor and front housing.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...xiapokang564341
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...hvy7sbkw8e
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...wenxian17880
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to lock the timing advance in place and tightening it to the specified torque. Technicians are instructed to keep parts clean and apply thread sealant to mounting studs during reinstallation.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing the automatic timing advance on a 3306 engine. It describes:
1. Installing a fuel pump timing pin and bolt to hold the camshaft in position.
2. Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3. Removing the tools and installing the front housing once the timing advance is installed.
This document provides instructions for installing an automatic timing advance on a 3306 engine. It involves using various tools to install a fuel pump timing pin and bolt to hold the automatic timing advance in place while tightening another bolt. The timing advance is then tightened to a specified torque and the tools are removed. Finally, the front housing is reinstalled.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...xiapokang564341
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...hvy7sbkw8e
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to hold the timing advance in place while tightening another bolt to the specified torque. The timing advance is then secured to the fuel pump camshaft and the tools are removed to complete the installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01...wenxian17880
This document provides instructions for removing and installing the automatic timing advance on a 3306 engine. It outlines the required tools and gives a step-by-step process that involves installing pins and bolts to lock the timing advance in place and tightening it to the specified torque. Technicians are instructed to keep parts clean and apply thread sealant to mounting studs during reinstallation.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
CASE IH STX450 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX440 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
More Related Content
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01300).pdf
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounting hardware.
3) It provides steps to disassemble the fuel injection pump housing, including removing the fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly, which weighs 24 kg for a 3304B engine.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
4) Disassembling the housing further by removing items like the fuel rack, lifters, camshaft, and bearings.
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer, bolt, and weight assembly into position on the fuel injection pump camshaft.
2) It also provides instructions for removing a fuel injection pump housing and governor from a 3304B or 3306B engine. It lists required tools and describes removing various components including nuts, bolts, tubes, and filters.
3) Additionally, it describes how to disassemble and assemble a fuel injection pump housing. The disassembly process involves removing components like a cover, fuel rack, lifters, snap ring, camshaft and bearings. The assembly process describes installing these
This document provides instructions for installing an automatic timing advance and removing a fuel injection pump housing and governor from a Caterpillar 3304B engine. It describes:
1) Using various tools to install the automatic timing advance and tighten bolts to the specified torques.
2) Removing components like lines, covers, and tubes to access the fuel injection pump housing and governor.
3) Using lifting equipment to safely remove the housing and governor assembly due to its weight.
The document contains detailed step-by-step instructions accompanied by illustrations. It is from a Caterpillar service manual for technicians performing maintenance or repairs.
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tightening it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing the removal process which includes removing various fasteners, lines, and the housing using lifting equipment.
3) It provides instructions for disassembling the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made
1) The document provides instructions for installing an automatic timing advance on a 3304 engine. It describes using various tools to install a washer and bolt to hold the timing advance in place and tighten it to the specified torque.
2) It describes removing the fuel injection pump housing and governor from a 3304B or 3306B engine. It lists the required tools and provides illustrations showing how to remove various components like lines, covers, and mounts to detach the housing.
3) It provides steps to disassemble the fuel injection pump housing, including removing the cover, fuel rack, lifters, snap ring, washer, camshaft and bearings. Identification marks should be made on original lifters
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjsjfjskeksmem
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjkskekdmmenm
The document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a washer and bolt and turning the fuel pump camshaft to insert a timing pin.
2) Installing the weight assembly and tightening the bolt to the specified torque.
3) Removing the tools and installing the front housing.
Caterpillar cat 966 e wheel loader (prefix 94x) service repair manual (94x064...fjjkskefmsemwe
This document provides instructions for installing the automatic timing advance on a Caterpillar 3306 engine. It describes:
1) Installing a fuel pump timing pin and bolt to hold the fuel pump camshaft in position.
2) Installing the weight assembly for the timing advance and tightening the bolt to the specified torque.
3) Removing the tools and installing the starting motor once the timing advance is installed.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The removal process involves removing various lines and components to access the housing. Disassembly involves using various tools to remove parts like the camshaft, bearings, and lifters. Reassembly requires installing these parts in reverse order and ensuring proper clearance and positioning.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
This document provides instructions for servicing the automatic timing advance on a 517 TRACK SKIDDER model powered by a 3304 engine. It describes removing the fuel injection pump housing and governor, disassembling the housing, and reassembling the housing. The procedures involve using various tools to install and remove parts like bearings, lifters, and seals. Technicians are advised to keep parts clean and apply engine oil during assembly.
Similar to Caterpillar Cat 235 EXCAVATOR (Prefix 32K) Service Repair Manual (32K00789-01300).pdf (20)
CASE IH STX450 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX440 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The instructions cover disconnecting batteries, removing the radiator, hood, fuel lines, air intake components, and other parts to fully separate the engine from the tractor.
CASE IH STX375 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting and ensuring all personnel are clear during movements.
CASE IH STX325 Tractor Service Repair Manual.pdfgen78guozun
The document provides instructions for removing and installing an engine. It is a multi-step process that begins by preparing the machine, disconnecting electrical and fluid connections, removing ancillary components, and then lifting the engine out of the machine. The installation process reverses these steps, carefully positioning and securing the engine before reconnecting all electrical and fluid lines. Safety is emphasized throughout with warnings about proper lifting equipment and blocking the machine securely.
Caterpillar Cat 257 Multi Terrain Loader (Prefix CMM) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing various components of a 3034 engine, including:
- Removing the flywheel, which requires drilling holes in it and using guide bolts.
- Removing the crankshaft rear seal using a drill bit and slide hammer puller to avoid damaging the crankshaft.
- Installing the crankshaft rear seal by lubricating it and setting it in place with a seal installer tool.
- Removing the flywheel housing by detaching lifting brackets, removing bolts, and tapping it off dowels.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix FMR) Service Repair Manual ...gen78guozun
This document provides instructions for removing and installing various engine components on a 257D Multi Terrain Loader, including:
- Engine oil relief valve - Instructions include loosening a plug, carefully removing a cap, and removing additional parts. Reinstallation is the reverse order.
- Engine oil pump - Removal involves removing screws and covers. Installation includes cleaning parts, checking clearances, applying grease, and reinstalling covers.
- Water pump - Removal requires removing belts, bolts, and the pump. Installation is the reverse order with a new gasket.
- Water temperature regulator - Removal involves disconnecting hoses, removing bolts and a gasket, and taking out the regulator. Install
This document provides instructions for removing and installing a piston pump on a 246D Skid Steer Loader. It outlines the required tools and gives step-by-step instructions to disassemble and assemble the pump. To remove the pump, hoses and harnesses must be disconnected, then lifting tools are used to support the pump while bolts are removed. Reinstallation is the reverse of removal. Detailed illustrations accompany each step to show how to remove components like valves, seals, and housing pieces, and reinstall them in the proper order.
CASE IH STX275 Tractor Service Repair Manual.pdfgen78guozun
The document provides step-by-step instructions for removing an engine from a tractor. It lists 27 steps including draining fluids, disconnecting wiring harnesses, removing hoses, and detaching mounting hardware. The goal is to fully separate the engine from other tractor components to allow for its removal from the vehicle. Safety precautions are advised when handling fluids, batteries, and heavy engine components.
1) The document provides instructions for removing and installing a lifter group on a C2.2 engine. It lists the required tool and removal steps, which include using a telescopic magnet to remove the lifters from the valve mechanism housing.
2) Installation instructions include cleaning components, lubricating the lifters, and inserting the lifters into the valve mechanism housing using the telescopic magnet. Proper lifter orientation is noted.
3) Completing the job involves installing the valve mechanism cover after checking lifter rotation.
The document provides instructions for removing and installing an exhaust manifold on a 249D Compact Track Loader powered by a C2.2 engine. The removal procedure involves loosening fasteners, removing the exhaust manifold and gasket, and removing any studs. For installation, clean surfaces are required, a new gasket is installed, the manifold is aligned and fastened, and bolts are tightened to the specified torque. The document also provides instructions for removing and installing valve springs, using the appropriate tools to compress springs at each step.
Caterpillar Cat 247 MULTI TERRAIN LOADER (Prefix CML) Service Repair Manual (...gen78guozun
This document provides instructions for removing and installing the lift cylinder on a 247 Multi Terrain Loader. It lists the required tools and safety precautions. The removal procedure involves releasing hydraulic pressure, disconnecting hoses and removing pins and bolts to detach the cylinder. Reinstallation is the reverse of removal. Torque specifications are provided for reassembly.
This document provides instructions for servicing components of a 246D Skid Steer Loader powered by a C3.3B engine. It includes procedures for removing and installing the crankshaft rear seal and wear sleeve, flywheel housing, crankshaft pulley, crankshaft front seal, and idler gear. The procedures note important steps like keeping parts clean, applying lubricants, using the proper tools, and torquing fasteners to the specified values. Cautions are also included to contain fluids and dispose of them properly.
This document provides instructions for removing and installing a fuel injection pump on a 246D Skid Steer Loader powered by a C3.3B engine. The procedure involves disconnecting fuel lines, removing mounting nuts and bolts, and extracting the pump. When installing, new gasket shims are used and bolts are tightened to the specified torques. Cleanliness of all fuel system components is emphasized to prevent contamination.
This document provides instructions for removing and installing the automatic timing advance and fuel injection pump housing & governor on a 245D Excavator with a 3406C diesel engine. It describes in detail the steps to take the components off the engine, including removing mounting bolts, nuts, hoses and other fasteners. The instructions note to cap or plug any openings immediately to prevent contamination. They also warn to use caution when removing certain parts like springs.
This document provides instructions for removing and installing various engine components on a 246 Skid Steer Loader, including the turbocharger, exhaust manifold, inlet manifold, and inlet and exhaust valve springs. The removal and installation procedures describe loosening clamps, removing bolts, plugging openings to prevent contamination, cleaning surfaces, and installing new gaskets. Tools required are also listed.
Caterpillar Cat 245B SERIES II EXCAVATOR (Prefix 6MF) Service Repair Manual (...gen78guozun
This document provides instructions for disassembling and assembling starting motors for a 245B Series II excavator. It describes removing components like the rear housing, brush holder, pinion drive housing, and shift lever housing. Tools needed are listed. Detailed photos show each step, such as lifting brush springs, removing retaining rings, and cleaning parts with mineral spirits. Instructions are provided for both 42-MT and 37-MT/41-MT style starting motors.
This document provides instructions for disassembling and assembling the swing and track motors of a 245 Excavator model. It describes over 30 steps to disassemble the motors by removing components like the shuttle valve, pump head, body, barrel, pistons, and more. It then describes over 20 steps for reassembling the motors, providing details on cleaning parts, applying oil, pressing components, setting bearings, and checking clearance. The goal is to properly disassemble and reassemble the swing and track motors while identifying parts to ensure correct alignment during reassembly.
This document provides instructions for disassembling and assembling the swing drive of a 245 Excavator model. It describes removing and installing over 40 individual parts in multiple steps. Key parts that must be removed include the swing drive motor, brake, various bearings, gears, seals, tubes, and manifolds. The instructions specify cleaning all parts thoroughly and applying anti-seize compound before reassembling the swing drive using the reverse of the disassembly steps. Special tools are required and parts must be heated or cooled to specific temperatures during installation.
Caterpillar Cat 245 EXCAVATOR (Prefix 95V) Service Repair Manual (95V00001-00...gen78guozun
This document provides instructions for servicing components of a 245 Excavator's 3406 vehicular engine, including:
- Disassembling and reassembling the fuel injection pump housing, which involves removing various parts like pumps, racks, lifters, and bearings, and replacing them in the proper order.
- Removing and installing the inlet manifold, which connects to the cylinder head and air cleaner components.
- Removing the aftercooler unit, which involves disconnecting hoses and pipes, removing mounting bolts, and taking out the core component. Detailed steps are provided for each disassembly and reassembly process.
The document provides instructions for removing and installing the engine oil pump on a 242B2 Skid Steer Loader with a 3024C engine. The removal procedure involves removing the front housing, idler gear components, suction pipe, and idler hub. The installation procedure outlines installing the idler hub, gears, rotor, cover, and suction pipe and includes checking end play clearance. Safety notices are provided throughout regarding contained fluids, cleanliness, and spring loaded components.
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00935398
Automatic Timing Advance - Install
SMCS - 1272-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4186 Fuel Pump Timing Pin 1
B 0L-2070 Bolt 1
C 5P-7307 Engine Turning Tool 1
D 4C-9874 Spanner Wrench 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00476281
1. Install washer (1) and bolt (2). Ensure that the cover of the fuel pump housing is removed.
Turn the fuel pump camshaft in the direction of the engine rotation until Tool (A) can be
installed in the notch of the camshaft.
2. Install Tool (A) and (B) into position. Install the weight assembly for the timing advance on
the fuel injection pump camshaft.
Illustration 2 g00476286
3. Use Tool (D) on the automatic timing advance and maintain a constant torque of 68 N·m
(50 lb ft). Tighten the bolt that fastens the automatic timing advance to the fuel pump
camshaft to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
4. Remove Tools (A), (B), (C) and (D). Install the starting motor.
End By: Install the front housing. Refer to Disassembly and Assembly, "Front Housing - Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 17:59:01 UTC+0800 2019
2/2
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i07103919
Fuel Injection Pump Housing and Governor - Remove
SMCS - 1286-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
8S-2264 Pump Impeller Puller 1
8B-7560 Step Plate 1
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
a. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 1 g00589938
3304B Engine
1. On the 3304B engine, remove oil supply line (26), oil drain line (25), and heat shield (27).
Inspect the O-ring seal around oil drain line (25). Replace the O-ring seal if the O-ring seal
is damaged. Remove the gaskets and the screen from the top of the turbocharger.
Note: The following illustrations are of a 3306B engine.
Illustration 2 g00452289
2. Remove six nuts (1) and the washers and remove cover (2).
Note: Separate nut (1) and the mounting stud, if the nut and the mounting stud come out of
the housing together. Apply thread sealant to the mounting studs and reinstall the mounting
studs to a depth of 19.0 ± 0.8 mm (0.74 ± 0.03 inch).
2/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 3 g00452292
3. Remove center bolt (3) and spacer (4).
Illustration 4 g00452293
4. Install center bolt (3) and leave a gap of 6.4 mm (.25 inch). Install Tool (A), as shown.
Tighten the stud to loosen the fuel pump drive gear from the taper on the fuel injection
pump camshaft.
5. Remove Tool (A) and bolt (3).
Illustration 5 g00452301
3/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 6. Remove tube assemblies (5) and (11). Disconnect one end of tube assemblies (8) and (9).
Disconnect clamp (10). Remove two bolts (7) and the washers and remove filter base (6)
with the filter and the gasket.
Illustration 6 g00452302
7. Remove two bolts (12), the washers and the gasket. Remove two bolts (14) and the gasket.
Remove tube assembly (13).
Illustration 7 g00452343
8. Use a lifting sling and a hoist to secure the fuel injection pump housing and the governor.
Note: Remove the heat shield (not shown) if equipped.
9. Disconnect solenoid ground (15). Remove three nuts (17). Remove two bolts (16) and the
washers. Remove the fuel injection pump housing and the governor from the engine. To
safely remove the fuel injection pump housing and the governor, use two technicians or a
suitable lifting device. The weight of the 3304B fuel injection pump housing and governor
is 24 kg (53 lb). The weight of the 3306B fuel injection pump housing and governor is
32 Kg (70 lb).
10. Remove the O-ring seals from the fuel injection pump housing and the governor.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 17:59:57 UTC+0800 2019
4/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01139602
Fuel Injection Pump Housing - Disassemble
SMCS - 1253-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
Start By:
A. Disassemble the governor. Refer to Disassembly and Assembly, "Governor - Disassemble".
B. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 1 g00456860
1. Remove cover (1) and the gasket.
Illustration 2 g00456923
2. Remove fuel rack (2) from the fuel injection pump housing.
Illustration 3 g00456924
2/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Note: If the original lifters are being reused in the fuel injection pump housing, place
identification marks on the lifters in order to identify the locations.
3. Remove lifters (3) from the fuel injection pump housing.
Illustration 4 g00456925
4. Position the fuel injection pump housing on wood blocks, as shown. Use Tool (A) in order
to remove snap ring (4) .
Illustration 5 g00456926
5. Use a soft hammer to push the camshaft toward the governor end of the fuel injection pump
housing in order to loosen washer (5). Remove washer (5) .
3/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 6 g00456927
6. Remove camshaft (6) .
Illustration 7 g00456928
7. Remove bearings (7) from the drive end of the fuel injection pump housing.
Illustration 8 g00456930
8. Remove bearings (8) from the governor end of the fuel injection pump housing.
4/5
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01138035
Fuel Injection Pump Housing - Assemble
SMCS - 1253-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1860 Retaining Ring Pliers 1
B 1P-0510 Driver Group 1
C
6V-2016 Plate 1
0S-1594 Bolt 2
6V-4818 Driver 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
1/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 1 g00457491
1. Use Tool (B) in order to install large bearing (1) in the governor end of the fuel injection
pump housing. Bearing joint (3) should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 0.25 ± 0.20 mm (.010 ± .008 inch) below the
surface of the fuel injection pump housing.
2. Use Tool (B) in order to install small bearing (2) in the governor end of the fuel injection
pump so that Tool (B) is 7.16 ± 0.13 mm (.282 ± .005 inch) below the surface of the fuel
injection pump housing.
Illustration 2 g00457492
3. Use Tool (B) in order to install large bearing (4) in the drive end of the fuel injection pump
housing. The bearing joint should be facing toward the top of the fuel injection pump
housing. Install the bearing so the bearing is 1.00 ± 0.25 mm (.039 ± .010 inch) below the
surface of the fuel injection pump housing.
2/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 3 g00457493
4. Install the plate of Tool (C) on the drive end of the fuel injection pump in order to install
small bearing (5) for the rack. Use clean grease in order to hold the new driver for the rack
bearing of Tool (C). Install the driver and the bearing in the plate. Ensure that the groove in
the driver is aligned with the pin in the plate and use a hammer to push the bearing into
position. The bearing will be installed to the correct depth when the shoulder of the driver is
against the plate.
5. Remove Tool (C) from the fuel injection pump housing. The fuel rack bearing must be
installed so that the fuel rack bearing is 0.25 ± 0.25 mm (.010 ± .010 inch) below the surface
of the housing.
Illustration 4 g00457494
6. Install camshaft (6) .
3/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 5 g00458729
7. Put the fuel injection pump housing upright, as shown. Place a wood block under the
camshaft.
8. Put washer (7) over the end of the camshaft. Use Tool (B) and spacer (8) in order to push
the washer against the seat on the camshaft. Spacer (8) has an inside diameter of 38.1 mm
(1.50 inch) and a length of 31.75 mm (1.250 inch). The camshaft must have an end play of
0.18 ± 0.08 mm (.007 ± .003 inch) when the washer is pushed against the shoulder of the
camshaft.
Illustration 6 g00457495
9. Use Tool (A) in order to install snap ring (9) .
4/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 7 g00458730
Note: Check the condition of the new lifters. Replace the lifters, if necessary. If the original
lifters are being reused, place the lifters in the original locations. New lifters are identical,
and the new lifters can be placed in any order.
10. Install six lifters (10) in the fuel injection pump housing. Ensure that the groove in the lifter
is aligned with the pin in the fuel injection pump housing.
Illustration 8 g00458731
11. Install rack (11). Ensure that the groove in the end of the rack is aligned with the ear (tab) of
the fuel rack bearing that is at the drive end of the fuel injection pump housing.
5/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 9 g00458732
12. Install the gasket and cover (12) .
End By:
a. Assemble the governor. Refer to Disassembly and Assembly, "Governor - Assemble".
b. Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 18:01:48 UTC+0800 2019
6/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111133
Fuel Injection Pump Housing and Governor - Install
SMCS - 1286-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 4C-9874 Spanner Wrench 1
C 6V-4186 Fuel Pump Timing Pin 2
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: The No. 1 piston must be set at the top center position (TC) in order to perform all of the
timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft rotation is
given.
1/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00460164
1. Remove the electric starting motor.
2. Install Tool (A) into the flywheel housing, as shown.
3. To find the TC position for the No. 1 piston, perform the following procedure:
a. Turn the flywheel clockwise or turn the flywheel in the opposite direction of the
engine rotation for approximately 30 degrees. This removes all play from the timing
gears.
Note: If you go past the bolt hole, repeat Step 3.a.
Illustration 2 g00460248
b. Remove plugs (1) and (2) .
2/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 3 g00460252
c. Turn the flywheel counterclockwise until a 3/8-16 X 3 1/2 NC bolt (4) can be
installed in the flywheel through the hole in the flywheel housing. The No. 1 and No.
6 pistons are now at the TC position. Plug (2) was removed for viewing through
inspection hole (3) .
Note: The No. 1 piston is on the compression stroke when the valves of the No. 1
cylinder are closed. The rocker arms for the inlet valves and for the exhaust valves
must have slight side-to-side movement.
d. In order to check the position of the inlet and exhaust valves, remove the valve
mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism Cover -
Remove and Install".
4. If the No. 1 piston is not on the compression stroke, remove bolt (4) and turn the flywheel
for 360 degrees counterclockwise. Install bolt (4). The No. 1 piston is now at the TC
position.
Illustration 4 g00460258
Typical example
3/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 5. Install Tool (C) in the fuel injection pump housing, as shown. Push on Tool (C) and turn
fuel injection pump camshaft (8). When Tool (C) engages the groove (slot) in the camshaft,
the fuel injection pump is in the TC position for the No. 1 piston.
Note: Check the condition of the O-ring seals. Replace the O-ring seals, if necessary.
6. Ensure that O-ring seals (5), (6), (7) and (9) are in position on the fuel injection pump
housing and the governor. Put clean engine oil on the seals.
Illustration 5 g00460259
7. Attach a hoist and put the fuel injection pump housing and the governor in position on the
timing gear plate and the oil manifold. Install three nuts (11), two bolts (10) and the
washers. Ensure that Tool (C) remains in place.
Illustration 6 g00460341
8. Install washer (12) with the large side outward. Install bolt (13) finger tight. Ensure that
Tool (C) is in the notch in the camshaft of the fuel injection pump.
4/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
23. Illustration 7 g00460342
9. Install Tool (B) on the fuel pump drive gear. Apply 68 N·m (50 lb ft) of force to the fuel
pump drive gear with timing bolt (3) in position in the flywheel and Tool (C) in position in
the fuel system. Apply this force in a clockwise direction when the engine is viewed from
the front. Use Tool (B) and a suitable torque wrench. Hold the 68 N·m (50 lb ft) of force on
Tool (B) and torque the drive gear bolt to a torque of 270 ± 25 N·m (200 ± 18 lb ft).
Remove Tool (B) and Tool (C) from the fuel pump and remove bolt (3) from the flywheel.
10. Use Tool (A) and turn the flywheel for two complete revolutions. When bolt (3) goes in the
hole in the flywheel and Tool (C) is installed in the notch in the camshaft, the timing is
correct.
11. Install plugs (1) and (2) .
12. Remove Tool (A). Install the electric starting motor.
13. Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve Mechanism
Cover - Remove and Install".
Illustration 8 g00460343
14. Put cover (14) and the gasket in position. Install four bolts (15) .
15. Put the fuel filter base, the gasket, and fuel filter (16) in position. Install two bolts (19) and
the washers.
5/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. 16. Install tube assemblies (21) and (22). Connect wire (20). Connect hoses (17) and (18) .
Illustration 9 g00589938
17. On the 3304B engines, install the strainer assembly in the turbocharger with the screen
downward. Install the gasket, the oil inlet line and the bolts. Install the O-ring seal on oil
drain line (25). Apply clean engine oil to the O-ring seal and install the gasket. Connect oil
drain line (25) and install the bolts. Install the clamps on the oil line.
Illustration 10 g00460346
18. Put cover (24) in position. Install nuts (23) and six washers. Tighten nuts (23) to a torque of
27 ± 7 N·m (20 ± 5 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Mon Sep 23 18:02:44 UTC+0800 2019
6/6
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 32K
Configuration: 235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00886792
Governor - Disassemble
SMCS - 1264-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0510 Driver Group 1
B 6V-2163 Spring Clamp 1
C 1P-1855 Retaining Ring Pliers 1
Start By:
A. Remove the fuel injection pump housing and the governor. Refer to Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Remove".
Note: To remove the governor for the disassembly of the fuel injection pump housing, perform
Steps 1, 2, 16, 22, 24, 25, 26, 27, 30, 32 and 34.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 1 g00453006
1. Remove fuel ratio control (1) from governor (2) .
Illustration 2 g00453007
Note: Illustration 2 shows the fuel ratio control that is still connected.
2. Remove six bolts (3), two bolts (5), housing (4) and the gasket.
Illustration 3 g00453008
2/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. 3. Remove governor spring (7), seat (6) and the washers.
Illustration 4 g00453009
4. Remove six bolts (8), cover (9) and the gasket. Use Tool (A) in order to remove seal (10) .
Illustration 5 g00453010
5. Remove low idle adjustment screw (12) and spring (11) .
3/12
235 EXCAVATOR 32K00789-01300 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...