Caterpillar Cat 262C Skid Steer Loader (Prefix MST) Service Repair Manual Instant Download.pdf

Service Repair Manual
Models
262C Skid Steer Loader

Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262C SKID STEER LOADER MST
Configuration: 262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems
Media Number -KENR5116-02 Publication Date -01/08/2012 Date Updated -07/08/2012
i02652282
Control Valve (Work Tool) - Disassemble - High Flow
SMCS - 5051-015
Disassembly Procedure
Start By:
A. Remove the control valve. Refer to Disassembly and Assembly, "Control Valve (Work
Tool) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/11
262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engine(...
2019/11/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01332398
1. Remove hose (1) .
2. Remove nuts (2) and cartridge assembly (3) .
3. Remove O-ring seals (4) from cartridge assemblies (3) .
2/11
2019/11/20

4. Remove bolt (7), retainer (6), and solenoid (5) .
5. Remove O-ring seals (8) from solenoid (5) .
3/11
2019/11/20

6. Remove nuts (9) and coil assemblies (10) .
7. Remove cartridge assemblies (11) .
8. Remove O-ring seals (12) from cartridge assemblies (11) .
4/11
2019/11/20

9. Remove bolt (13), retainer (14), and solenoid (15) .
10. Remove O-ring seals (16) from solenoid (15) .
11. Remove nut (18) and coil assembly (17) .
5/11
2019/11/20

12. Remove O-ring seals (19) from coil assembly (17) .
13. Remove cartridge assembly (20) .
6/11
2019/11/20

14. Remove O-ring seals (21), backup ring (22), and screen (23) from cartridge assembly (20) .
15. Reposition the control valve, as shown.
16. Remove relief valves (24) and (25) .
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7/11
2019/11/20

18. Remove plug (26) and the O-ring seal. Remove spool assembly (27). Remove plug (28) and
the O-ring seal.
8/11
2019/11/20

19. Remove plug (29) and the O-ring seal. Remove spring (30), retainer (31), and spool (32).
Remove plug (35) and the O-ring seal. Remove spring (34) and retainer (33) .
20. Remove plug (36) and the O-ring seal. Remove spring (37) and retainer (38). Remove plug
(40) and the O-ring seal. Remove spool assembly (39) .
9/11
2019/11/20

21. Remove plug (41) and the O-ring seal. Remove spring (42), retainer (43), and spool (44).
Remove plug (47) and the O-ring seal. Remove spring (46) and retainer (45) .
10/11
262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engin...
2019/11/20

22. Remove plug (48) and the O-ring seal. Remove spring (49), valve (50), spring (51), and
valve (52). Repeat for the remaining valve assemblies.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 22:59:16 UTC+0800 2019
11/11
262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engin...
2019/11/20

Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262C SKID STEER LOADER MST
Configuration: 262C Skid Steer Loader MST00001-UP (MACHINE) POWERED BY 3044C Engine
Disassembly and Assembly
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems
Media Number -KENR5116-02 Publication Date -01/08/2012 Date Updated -07/08/2012
i02652632
Control Valve (Work Tool) - Assemble - High Flow
SMCS - 5051-016
Assembly Procedure
Note: Cleanliness is an important factor. Before assembly, thoroughly clean all parts in cleaning
fluid. Allow the parts to air dry. Do not use wiping cloths or rags to dry parts. Lint may be
deposited on the parts which may cause trouble. Inspect all parts. If any parts are worn or
damaged, use new parts for replacement. Dirt and other contaminants can damage the precision
component. Perform assembly procedures on a clean work surface. Keep components covered and
protected at all times.
Note: Check the O-ring seals, the gaskets, and the seals for wear or for damage. Replace the
components, if necessary.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/12
2019/11/20

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
1. Install valve (52), spring (51), valve (50), and spring (49). Install the O-ring seal and plug
(48). Repeat for the remaining valve assemblies.
2/12
2019/11/20

injury.
2. Install spool (44), retainer (43), and spring (42). Install the O-ring seal and plug (41). Install
retainer (45) and spring (46). Install the O-ring seal and plug (47) .
3/12
2019/11/20

injury.
3. Install spool assembly (39). Install the O-ring seal and plug (40). Tighten plug (40) to a
torque of 122 ± 12 N·m (90 ± 9 lb ft).
4. Install retainer (38) and spring (37). Install the O-ring seal and plug (36). Tighten plug (36)
to a torque of 122 ± 12 N·m (90 ± 9 lb ft).
4/12
2019/11/20

injury.
5. Install spool (32), retainer (31), and spring (30). Install the O-ring seal and plug (29). Install
retainer (33) and spring (34). Install the O-ring seal and plug (35) .
injury.
5/12
2019/11/20

6. Install spool assembly (27). Install the O-ring seal and plug (26). Tighten plug (26) to a
torque of 142 ± 14 N·m (105 ± 10 lb ft). Install the O-ring seal and plug (28) .
8. Install relief valves (24) and (25). Tighten all of the relief valves to a torque of 45 ± 5 N·m
(33 ± 4 lb ft).
9. Install O-ring seals (21), backup ring (22), and screen (23) onto cartridge assembly (20) .
6/12
2019/11/20

10. Install cartridge assembly (20). Tighten cartridge assembly (20) to a torque of 30 ± 3 N·m
(22 ± 2 lb ft).
11. Install O-ring seals (19) onto coil assembly (17) .
7/12
2019/11/20

12. Install coil assembly (17) and nut (18). Tighten nut (18) to a torque of 3.4 ± 0.4 N·m (30.1 ±
3.5 lb in).
13. Install O-ring seals (16) onto solenoid (15) .
14. Install solenoid (15), retainer (14), and bolt (13). Tighten bolt (13) to a torque of 28 ± 7 N·m
(21 ± 5 lb ft).
8/12
2019/11/20

Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading

15. Install O-ring seals (12) onto cartridge assemblies (11) .
16. Install cartridge assemblies (11). Tighten cartridge assemblies (11) to a torque of 40 ± 5
N·m (30 ± 4 lb ft).
9/12
2019/11/20

Caterpillar Cat 262C Skid Steer Loader (Prefix MST) Service Repair Manual Instant Download.pdf

Recommended

Recommended

More Related Content

More from f8seodkdmdmed3

More from f8seodkdmdmed3 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 262C Skid Steer Loader (Prefix MST) Service Repair Manual Instant Download.pdf