Caterpillar cat 232 skid steer loader (prefix cab) service repair manual (cab00001 and up)

Service Repair Manual
Models
Caterpillar Cat 232 SKID
STEER LOADER

Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 232 SKID STEER LOADER CAB
Configuration: 216 226 232 242 Skid Steer Loader CAB00001-UP (MACHINE) POWERED BY 3024C, 3034 Engine
Disassembly and Assembly
216, 226, 232 and 242
Skid Steer Loaders Machine Systems
Media Number -RENR4838-02 Publication Date -01/11/2009 Date Updated -04/11/2009
i01780412
Control Valve (Work Tool) - Remove
SMCS - 5051-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A
6V-9507 Face Seal Plug (9/16 - 18 THD) 4
6V-9828 Cap As (9/16 - 18 THD) 4
6V-9508 Face Seal Plug (11/16 - 16 THD) 2
6V-9829 Cap As (11/16 - 16 THD) 2
6V-9511 Face Seal Plug (1 3/16 - 12 THD) 1
6V-9832 Cap As (1 3/16 - 12 THD) 1
9U-7084 Cap (1 5/16) 1
Start By:
A. Release the pressure in the hydraulic system. Refer to Disassembly and Assembly,
"Hydraulic System Pressure - Release".
Note: SERVICE DATA: TOOLING (A) WILL NOT BE IDENTIFIED IN
PHOTOGRAPHS IN THE REMOVAL OR THE INSTALLATION. THIS TOOLING IS
SHOWN IN ORDER TO ASSIST THE EXPERIENCED SERVICEMAN.
1/5216 226 232 242 Skid Steer Loader CAB00001-UP (MACHINE) POWERED BY 302...
2019/10/18https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Personal injury can result from hydraulic oil pressure and hot oil.
Hydraulic oil pressure can remain in the hydraulic system after the
engine has been stopped. Serious injury can be caused if this pressure is
not released before any service is done on the hydraulic system.
Make sure all of the work tools have been lowered to the ground, and
the oil is cool before removing any components or lines. Remove the oil
filler cap only when the engine is stopped, and the filler cap is cool
enough to touch with your bare hand.
Personal injury or death can result without releasing all of the
hydraulic pressure.
Release all the pressure from the hydraulic system before any lines are
disconnected.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contamination of the hydraulic system with foreign material will
reduce the service life of the hydraulic system components.
To prevent contaminants from entering the hydraulic system, always
plug or cap the lines, fittings, or hoses as they are disconnected. Cover

any disassembled components and clean them properly before
assembly.
Clean the hydraulic system properly after any major component
exchange or especially after a component failure, to remove any
contamination.
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
1. Drain the hydraulic tank. Refer to Operation and Maintenance Manual, SEBU7468,
"Hydraulic System Oil - Change".
Illustration 1 g00902296
2. Disconnect seven hose assemblies (1). Disconnect six tube assemblies (2) .

3. Disconnect two harness assemblies (3). Loosen clamp (4). Disconnect hose (5) .
4. Remove bolts (6) .

5. Remove bolts (8). Remove bracket (7). Use two people to remove control valve (9). The
weight of control valve (9) is approximately 34 kg (74 lb).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 08:31:03 UTC+0800 2019

Shutdown SIS
Previous Screen
216, 226, 232 and 242
i01764046
Control Valve (Work Tool) - Disassemble
SMCS - 5051-015
Disassembly Procedure
Start By:
A. Remove the Control Valve. Refer to Disassembly and Assembly, "Control Valve
(Worktool) - Remove".
1. Remove solenoids (1). Remove fittings (2). Remove fittings (3) .

2. Remove O-ring seal (4). Remove O-ring seal (5). Remove O-ring seal (6) .
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
3. Remove the plug and O-ring seal (7) .

4. Remove spring (9). Remove check valve (8) .
5. Repeat Steps 3 through 4 for the remaining plugs.
Note: Observe the orientation of the fittings and the accumulator.
6. Remove fitting (10). Remove fitting (11). Remove adapter (12). Remove fitting (13) .

8. Remove spring (15) .
9. Repeat Steps 7 through 8 for the remaining plug.

10. Remove the cap and O-ring seal (16) .
11. Remove relief valves (17) .

13. Remove spring (18). Remove the screen and washer (19) .

14. Remove spool (20). Remove the plug, the O-ring seal, and spring (21) .
15. Remove spool (22) .

17. Remove spring (24) .
18. Remove fitting (25). Remove relief valve (26). Remove spool (27) .

19. Apply heat to bolt (31). Remove bolt (31). Remove washer (30). Remove spring (29).
Remove washer (28) .

21. Remove spring (33). Remove check valve (34) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Oct 18 08:32:02 UTC+0800 2019

Shutdown SIS
Previous Screen
216, 226, 232 and 242
i01768119
Control Valve (Work Tool) - Assemble
SMCS - 5051-016
Assembly Procedure
Table 1
Required Tool
Tool Part Number Part Name Qty
A 155-0695 Thread Lock Compound 1
1. Install check valve (34). Install spring (33) .

Improper assembly of parts that are spring loaded can cause bodily
injury.
To prevent possible injury, follow the established assembly procedure
and wear protective equipment.
2. Install the cap and O-ring seal (32). Torque the cap to 25 � 3 N�m (18 � 2 lb ft).
injury.

3. Install washer (28). Install spring (29). Install washer (30). Apply Tooling (A) to the threads
of bolt (31). Install bolt (31). Torque bolt (31) to 10 � 1 N�m (89 � 9 lb in).
4. Install spool (27). Install relief valve (26). Torque the relief valve to 10 � 1 N�m (7 � 1 lb
ft). Install fitting (25) .
5. Install spring (24) .

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

injury.
7. Install spool (22) .

injury.
8. Install the plug, the O-ring seal, and spring (21). Torque the plug to 65 � 7 N�m (48 � 5 lb
ft). Install spool (20) .
9. Install the screen and washer (19). Install spring (18) .

injury.
10. Install the plug and O-ring seal (14). Torque the plug to 65 � 7 N�m (48 � 5 lb ft).
11. Install relief valves (17). Torque relief valves to 45 � 5 N�m (33 � 4 lb ft).

injury.
13. Install spring (15) .

Caterpillar cat 232 skid steer loader (prefix cab) service repair manual (cab00001 and up)

Recommended

Recommended

More Related Content

Similar to Caterpillar cat 232 skid steer loader (prefix cab) service repair manual (cab00001 and up)

Similar to Caterpillar cat 232 skid steer loader (prefix cab) service repair manual (cab00001 and up) (15)

More from jjskefkskemik

More from jjskefkskemik (20)

Recently uploaded

Recently uploaded (20)

Caterpillar cat 232 skid steer loader (prefix cab) service repair manual (cab00001 and up)