2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262C2 SKID STEER LOADER TMW
Configuration: 262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems
Media Number -KENR5116-02 Publication Date -01/08/2012 Date Updated -07/08/2012
i02652282
Control Valve (Work Tool) - Disassemble - High Flow
SMCS - 5051-015
Disassembly Procedure
Start By:
A. Remove the control valve. Refer to Disassembly and Assembly, "Control Valve (Work
Tool) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 14 g01332628
14. Remove O-ring seals (21), backup ring (22), and screen (23) from cartridge assembly (20) .
Illustration 15 g01332630
15. Reposition the control valve, as shown.
16. Remove relief valves (24) and (25) .
Illustration 16 g01332649
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
7/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 17. Reposition the control valve, as shown.
18. Remove plug (26) and the O-ring seal. Remove spool assembly (27). Remove plug (28) and
the O-ring seal.
Illustration 17 g01332699
Illustration 18 g01332700
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
8/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 19. Remove plug (29) and the O-ring seal. Remove spring (30), retainer (31), and spool (32).
Remove plug (35) and the O-ring seal. Remove spring (34) and retainer (33) .
Illustration 19 g01332702
Illustration 20 g01332813
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
20. Remove plug (36) and the O-ring seal. Remove spring (37) and retainer (38). Remove plug
(40) and the O-ring seal. Remove spool assembly (39) .
9/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 21 g01332821
Illustration 22 g01332823
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
21. Remove plug (41) and the O-ring seal. Remove spring (42), retainer (43), and spool (44).
Remove plug (47) and the O-ring seal. Remove spring (46) and retainer (45) .
10/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engi...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 23 g01332824
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
22. Remove plug (48) and the O-ring seal. Remove spring (49), valve (50), spring (51), and
valve (52). Repeat for the remaining valve assemblies.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Nov 20 15:28:42 UTC+0800 2019
11/11262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engi...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
14. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 262C2 SKID STEER LOADER TMW
Configuration: 262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine
Disassembly and Assembly
246C, 256C, 262C, 262C2 and 272C Skid Steer Loaders Machine Systems
Media Number -KENR5116-02 Publication Date -01/08/2012 Date Updated -07/08/2012
i02697361
Control Valve (Work Tool) - Disassemble
SMCS - 5051-015
S/N - TMW1-UP
Disassembly Procedure
Start By:
A. Remove the control valve. Refer to Disassembly and Assembly, "Control Valve (Work
Tool) - Remove".
Note: Cleanliness is an important factor. Before you begin the disassembly procedure, the exterior
of the components should be thoroughly cleaned. This will help to prevent dirt from entering the
internal mechanism. Precision components can be damaged by contaminants or by dirt. Perform
disassembly procedures on a clean work surface. Keep components covered and protected at all
times.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/8262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 6 g01353507
Personal injury can result from being struck by parts propelled by a
released spring force.
Make sure to wear all necessary protective equipment.
Follow the recommended procedure and use all recommended tooling to
release the spring force.
5. Remove plug (6), plug (12), and the O-ring seals.
6. Remove spring (7), washer (8), spool (9), spring (11), and washer (10) .
Illustration 7 g01353508
Illustration 8 g01353598
4/8262C2 Skid Steer Loader TMW00001-UP (MACHINE) POWERED BY C3.4 Engine(...
2019/11/20https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
