This document provides instructions for removing and installing fuel injection lines, fuel injector nozzles, and a fuel ratio control on a Caterpillar 225 excavator engine. The procedures include removing brackets and disconnecting nuts to remove the lines, using specialized tools to pull the nozzles, and removing bolts and seals to take off the fuel ratio control. Technicians are advised to keep parts clean and contain fluids during disassembly.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
This service repair manual provides instructions for removing and installing a gas spring on a 216 Skid Steer Loader. It details removing the bolts and pins holding the gas spring in place and using lifting tools to raise the cab enough to fully extend the spring. When installing, the left spring must be installed first and pins, bolts and clips are used to secure it in place. Similar steps are followed for the right spring and tools are removed before lowering the cab.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjsjjefkskekm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 320 c excavator (prefix hbc) service repair manual (hbc00001 ...ufjjskekkmde
- The document provides instructions for removing and installing fuel injection lines, nozzles, and a pump on a 320C excavator engine.
- It describes disconnecting lines, removing clamps and bolts, capping openings to prevent contamination, and using tools like a slide hammer for removal.
- Reinstallation involves cleaning parts, installing in reverse order while torquing bolts to the specified values, and ensuring proper alignment of components.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
This service repair manual provides instructions for removing and installing a gas spring on a 216 Skid Steer Loader. It details removing the bolts and pins holding the gas spring in place and using lifting tools to raise the cab enough to fully extend the spring. When installing, the left spring must be installed first and pins, bolts and clips are used to secure it in place. Similar steps are followed for the right spring and tools are removed before lowering the cab.
This document provides instructions for servicing the fuel injection pump housing on a Caterpillar 3304B engine. It describes how to remove the housing, disassemble it, and reassemble it. The key steps are:
1. Remove the fuel injection pump housing from the engine using lifting slings and tools.
2. Disassemble the housing by removing components like the fuel rack, lifters, camshaft, and bearings.
3. Reassemble the housing by pressing in new bearings, installing the camshaft and washer, fitting lifters and the fuel rack, and replacing the cover.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjsjjefkskekm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 320 c excavator (prefix hbc) service repair manual (hbc00001 ...ufjjskekkmde
- The document provides instructions for removing and installing fuel injection lines, nozzles, and a pump on a 320C excavator engine.
- It describes disconnecting lines, removing clamps and bolts, capping openings to prevent contamination, and using tools like a slide hammer for removal.
- Reinstallation involves cleaning parts, installing in reverse order while torquing bolts to the specified values, and ensuring proper alignment of components.
Caterpillar cat 966 h wheel loader (prefix bs6) service repair manual (bs6000...fudjsjfekskkem
The document provides instructions for removing and installing inlet and exhaust valves on a Caterpillar C11 engine. It describes:
1) Using a valve spring compressor tool to remove valve locks, springs, rotators, and valves.
2) Lubricating and installing new valves, seals, springs and locks using the compressor tool.
3) To begin, the cylinder head must be removed and cleaned of contaminants before starting the valve job.
Caterpillar cat 329 f l excavator (prefix erl) service repair manual (erl0000...fkjsekksmem
1. The document provides removal and installation instructions for inlet and exhaust valves on a Caterpillar 329F L Excavator with a C7.1 engine.
2. The procedure involves using special tools to compress the valve springs to remove the valve keepers and other components, and then reversing the process to install new components.
3. Technicians are instructed to clean and inspect all parts, lubricate the valves, and ensure proper valve depth before installing and securing the valve assembly components.
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. The removal process involves disconnecting nuts and brackets to remove the lines and using special tools to pull nozzles while preventing them from turning. Installation requires cleaning parts, adding new seals, and reconnecting lines and brackets while applying specified torques. Proper alignment of notches and tabs is important when reinstalling nozzles.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It outlines the necessary tools and safety precautions. The procedure involves removing brackets and disconnecting nuts to remove the lines, and reversing the steps to install new lines, ensuring nozzles are properly supported and tightened to the specified torque. Cleaning tools are also described for cleaning nozzles and cylinder bores.
Caterpillar Cat 235 EXCAVATOR (Prefix 62X) Service Repair Manual (62X00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It describes:
- Removing fuel injection line brackets and disconnecting lines from the fuel pumps and nozzles
- Installing lines by tightening nuts to the specified torque and replacing brackets
- Removing nozzles using special tools to prevent damage and removing sealing components
- Cleaning and installing nozzles with new seals, ensuring notches are aligned
- Removing the fuel ratio control by disconnecting lines and moving it out of the governor lever assembly
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjkskefkemm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each procedure.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each job. Safety notices emphasize keeping parts clean and containing fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts and washers to detach the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts and washers.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. Installing involves reversing the removal steps - placing the base back on and reconnecting the fuel lines.
3. Removing the fuel injection lines requires disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation reverses this process.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Same frutteto³ s 90 tractor service repair manual (sn 1001 and up)fjkskefksmeme
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
Caterpillar cat 385 c l excavator (prefix jcm) service repair manual (jcm0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
More Related Content
Similar to Caterpillar cat 225 excavator (prefix 76 u) service repair manual (76u00001 00693)
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. The removal process involves disconnecting nuts and brackets to remove the lines and using special tools to pull nozzles while preventing them from turning. Installation requires cleaning parts, adding new seals, and reconnecting lines and brackets while applying specified torques. Proper alignment of notches and tabs is important when reinstalling nozzles.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It outlines the necessary tools and safety precautions. The procedure involves removing brackets and disconnecting nuts to remove the lines, and reversing the steps to install new lines, ensuring nozzles are properly supported and tightened to the specified torque. Cleaning tools are also described for cleaning nozzles and cylinder bores.
Caterpillar Cat 235 EXCAVATOR (Prefix 62X) Service Repair Manual (62X00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It describes:
- Removing fuel injection line brackets and disconnecting lines from the fuel pumps and nozzles
- Installing lines by tightening nuts to the specified torque and replacing brackets
- Removing nozzles using special tools to prevent damage and removing sealing components
- Cleaning and installing nozzles with new seals, ensuring notches are aligned
- Removing the fuel ratio control by disconnecting lines and moving it out of the governor lever assembly
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjkskefkemm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Precautions are provided to keep parts clean and contain fluids.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each procedure.
This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each job. Safety notices emphasize keeping parts clean and containing fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts and washers to detach the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts and washers.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. Installing involves reversing the removal steps - placing the base back on and reconnecting the fuel lines.
3. Removing the fuel injection lines requires disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation reverses this process.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Similar to Caterpillar cat 225 excavator (prefix 76 u) service repair manual (76u00001 00693) (20)
Same frutteto³ s 90 tractor service repair manual (sn 1001 and up)fjkskefksmeme
The document provides instructions for the reader to click on a link to access a complete manual with no waiting. It notes that if clicking the link does not work, the reader should first download the PDF document and then click on it to access the manual.
Caterpillar cat 385 c l excavator (prefix jcm) service repair manual (jcm0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 385 c fs excavator (prefix mma) service repair manual (mma000...fjkskefksmeme
This document provides instructions for removing and installing various components of a Caterpillar C-18 diesel engine, including:
1. Removing the variable valve actuator by disconnecting harnesses and removing mounting bolts and nuts.
2. Installing the variable valve actuator by reinstalling mounting hardware and reconnecting harnesses.
3. Removing the rocker arm assembly by removing mounting bolts and using a lifting bracket.
4. Disassembling the rocker arm by removing adjustment screws, buttons, seals, and arms from the rocker shaft.
Caterpillar cat 385 c fs excavator (prefix eam) service repair manual (eam000...fjkskefksmeme
This service repair manual provides instructions for removing and installing various engine components on a Caterpillar 385C FS excavator powered by a C-18 engine. The document includes procedures for removing and installing the valve actuator, rocker arm and shaft, and disassembling and assembling the rocker arm. Diagrams and specifications are provided to correctly perform the repair and replacement of parts. Technicians are advised to keep components clean and lubricated during disassembly and reassembly.
Caterpillar cat 385 c excavator (prefix kgb) service repair manual (kgb00001 ...fjkskefksmeme
This document provides the disassembly and assembly procedures for the travel motor of 385C and 385C L excavator models. The disassembly procedure involves 40 steps to dismantle the various components of the travel motor. These include removing the head, relief valves, spools, pistons, springs, seals, port plate, friction plates, barrel assembly and other internal parts. Precautions are provided to handle parts under spring tension. The assembly procedure consists of 12 steps to reinstall the components in reverse order. Cleanliness and applying a light film of oil to parts is emphasized.
Caterpillar cat 385 c excavator (prefix kbc) service repair manual (kbc00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the travel motor of a 385C Excavator. It lists 40 steps for disassembly, including removing the head, relief valves, port plate, piston, swashplate, shaft, and seals. It also lists 12 steps for assembly, starting with installing the lip seal in the housing and ending by applying a light film of oil to all components before final assembly. Precision tools are required and cleanliness is important to prevent contamination.
Caterpillar cat 385 c excavator (prefix jcm) service repair manual (jcm00001 ...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of a 385C excavator. It lists 34 steps for disassembly, removing components like housing covers, gears, shafts and seals. It notes the importance of cleanliness. For assembly, it lists 1 step to reassemble the final drive on a repair stand and cribbing, referring to other assembly instructions. Key points are cleaning all parts thoroughly before and during assembly and replacing any worn or damaged components.
Caterpillar cat 385 b l excavator (prefix rcd) service repair manual (rcd0000...fjkskefksmeme
The document provides instructions for disassembling and assembling various components of an excavator control valve, including:
1. Disassembling the proportional valve by removing bolts, nuts, and cartridge components.
2. Assembling the attachment, bucket, and boom control valve by installing O-rings, plugs, resolver valves, springs, and actuator groups.
3. Assembling the right travel, left travel, and stick control valve by installing spools, plugs, resolver valves, and O-rings. Detailed steps and illustrations are provided for each disassembly and assembly procedure.
Caterpillar cat 385 b l excavator (prefix fdl) service repair manual (fdl0000...fjkskefksmeme
This document provides instructions for disassembling and assembling the final drive of an excavator model 385B.
The disassembly process involves removing 27 parts from the final drive housing including gears, shafts, seals and bearings. Tools and lifting devices are required to remove some heavy components weighing up to 340 pounds.
The assembly process reverses the disassembly steps and provides details on installing seals, bearings and shims to achieve proper bearing preload. Precise measurement and calculation are involved to determine the correct shim thickness. Lubricants and cleaning procedures are also specified.
Yamaha outboard f50 feht service repair manual sn1000001fjkskefksmeme
This document provides a service manual for outboard motor models F50F, FT50G, F60C, and FT60D. It contains general information about how to use the manual, identification of applicable models and features, predelivery checks, and troubleshooting guides. The manual is organized into sections covering general information, specifications, periodic checks and adjustments, fuel system, power unit, lower unit, bracket unit, electrical systems, and troubleshooting. It also includes exploded diagrams of components and lists parts with quantities and specifications.
Yale b974 gdp50 lx lift truck service repair manualfjkskefksmeme
This document provides service information for a GLP060LX or GDP50LX lift truck. It contains:
1. A table of contents listing the sections and part numbers for the service manual.
2. A general warning about safety procedures when putting the lift truck on blocks for maintenance.
3. Instructions for removing and installing the hood, seat, and side covers of the lift truck, including disconnecting wiring harnesses and removing fasteners.
Yale (e877) gdp130 ec lift truck service repair manualfjkskefksmeme
The document provides instructions for raising and lowering the operator cab on a lift truck, as well as removing and installing the cab door. Key steps include:
1. Using the cab tilt hand pump or electric pump to raise or lower the cab until it locks in position.
2. Pulling the tilt latch release to fully raise or lower the cab.
3. Attaching lift straps and cushions to safely remove the cab door from its hinges and place it on the ground.
4. Reinstalling the cab door by lifting it back into position on the hinges and adjusting if needed.
Perkins peregrine edi and 1300 series edi ws diesel engine service repair manualfjkskefksmeme
This document is a workshop manual for Perkins Peregrine EDi and 1300 Series EDi diesel engines. It provides information on servicing various engine components including the cylinder head, pistons, connecting rods, crankshaft, timing case, and related systems. The manual contains detailed instructions for removal, inspection, repair and installation of engine parts, with torque specifications and safety precautions. It is intended as a guide for technicians servicing these Perkins diesel engines.
Perkins peregrine edi and 1300 series edi wq diesel engine service repair manualfjkskefksmeme
This document is a workshop manual for Perkins Peregrine EDi and 1300 Series EDi diesel engines. It provides information on servicing and repairing engine components. The manual contains chapters covering the cylinder head assembly, piston and connecting rod assemblies, crankshaft assembly, timing case and drive assembly, and other systems. It includes detailed instructions for removing, inspecting, and installing components with torque specifications. The document is intended as a reference for technicians servicing these Perkins diesel engines.
Perkins 2800 series 2806 c e16 diesel engine service repair manualfjkskefksmeme
This document provides maintenance and repair instructions for a Perkins 2800 Series 6-cylinder turbocharged diesel engine. It contains specifications, procedures for disassembling and assembling various engine components, such as the cylinder head, pistons, crankshaft, and timing gears. Safety precautions and environmental protection guidelines are also outlined. The manual is intended to assist technicians in servicing and repairing these industrial diesel engines.
Perkins 2000 series 2006 diesel engine(model 2006 twg2)service repair manualfjkskefksmeme
This document provides instructions for servicing and repairing Perkins 2000 Series 6-cylinder diesel engines. It details procedures for removing and installing major engine components like the cylinder head, pistons, crankshaft, and fuel system parts. Safety precautions are also outlined regarding working on diesel engines, as well as specifications for torque values and recommended clearances between parts.
Perkins 1300 series we diesel engine service repair manualfjkskefksmeme
This document is a workshop manual that provides specifications, repair and maintenance instructions for Perkins Peregrine and New Generation 1300 Series diesel engines. It contains chapters covering the cylinder head assembly, piston and connecting rod assemblies, crankshaft assembly, timing case and drive assembly, and other systems. The manual includes detailed parts lists, diagrams, specifications, and recommended torque settings to guide technicians in servicing and repairing engine components.
Kubota g21 ld tractor mower service repair manualfjkskefksmeme
This document provides maintenance information for a workshop manual, including:
- Identification of engine and machine serial numbers, hour meter, etc.
- General precautions for handling parts, wiring, batteries, and using proper lubricants.
- Tightening torques for screws, bolts and nuts in metric and imperial units.
- Maintenance checklists and inspection schedules for daily, 50 hour, 100 hour, yearly and other periodic checks.
- Lists of special tools required for engine and machine maintenance and repair.
- Limitations on implement usage.
The document outlines identification, safety, inspection and maintenance procedures for workshop personnel servicing this equipment.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Top-Quality AC Service for Mini Cooper Optimal Cooling PerformanceMotor Haus
Ensure your Mini Cooper stays cool and comfortable with our top-quality AC service. Our expert technicians provide comprehensive maintenance, repairs, and performance optimization, guaranteeing reliable cooling and peak efficiency. Trust us for quick, professional service that keeps your Mini Cooper's air conditioning system in top condition, ensuring a pleasant driving experience year-round.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
car rentals in nassau bahamas | atv rental nassau bahamasjustinwilson0857
At Dash Auto Sales & Car Rentals, we take pride in providing top-notch automotive services to residents and visitors alike in Nassau, Bahamas. Whether you're looking to purchase a vehicle, rent a car for your vacation, or embark on an exciting ATV adventure, we have you covered with our wide range of options and exceptional customer service.
Website: www.dashrentacarbah.com
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/5
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00448807
1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
Illustration 2 g00448808
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00448809
3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
Illustration 4 g00448810
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 5 g00475542
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00475546
4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:12:37 UTC+0800 2019
5/5
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Do not allow the tops of the fuel injector nozzles to turn while the fuel
lines are loosened. The fuel injector nozzles will be damaged if the tops
of the fuel injector nozzle turns in the body. Defective fuel injector
nozzles will damage the engine due to incorrect spray patterns.
Illustration 1 g00448820
1. Remove bolt (1) and the clamp that secures the fuel injector nozzle.
Illustration 2 g00448821
2. Install Tool (A) over the fuel injector nozzle. Turn screw (2) counterclockwise until the
button on the end of the screw is just above the bolt hole for the clamp that holds down the
fuel injector nozzle.
3. Tilt Tool (A) upward so that the inside lip of the fuel nozzle puller is under the diameter of
the fuel injector nozzle.
4. Turn screw (2) clockwise until the button on Tool (A) goes into the bolt hole for the clamp
that holds down the fuel injector nozzle.
2/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Do not exceed the recommended torque on the screw of the 6V-6980
Fuel Nozzle Puller in order to remove the nozzle. The nozzle will bend
or break if a torque greater than 17 N·m (13 lb ft) is applied.
5. Turn screw (2) clockwise in order to lift the fuel injector nozzle out of the bore. After the
fuel injector nozzle is loose in the bore of the cylinder head, move the fuel injector nozzle
upward and move the fuel injector nozzle downward. Moving the fuel injector nozzle helps
to loosen any carbon buildup and aids in the removal of the fuel injector nozzle.
6. When Tool (A) is used to remove the fuel injector nozzles, remove the carbon dam seal on
the end of the fuel injector nozzle.
Illustration 3 g00448822
7. If the fuel injector nozzle cannot be removed with Tool (A), Tool (B) must be used.
Note: When Tool (B) is used, it is likely that the fuel injector nozzle cannot be used again.
A new fuel injector nozzle will need to be installed as a replacement.
Note: Align the centerline of Tool (B) with the extended centerline of fuel injector nozzle
(3). This procedure will help prevent distortion of the fuel injector nozzle which can cause
the fuel injector nozzle to bend or break.
8. Remove the protective cap and install Tool (B) .
9. Use the slide hammer in order to remove fuel injector nozzle (3) .
10. Remove the compression seal from the fuel injector nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:13:33 UTC+0800 2019
3/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048591
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4979 Carbon Seal Installation Tool 1
B 8S-2245 Injector Cleaning Tool 1
C 6V-4089 Reamer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00448903
1. Put carbon dam seal (1) on the small end of Tool (A). Expand carbon dam seal (1) by
sliding carbon dam seal (1) to the large end of Tool (A). Put Tool (A) against the fuel
injector nozzle. Slide carbon dam seal (1) from Tool (A) to the fuel injector nozzle. Slide
carbon dam seal (1) into position in the groove of the fuel injector nozzle, as shown. Use
Tool (A) in order to install carbon dam seal (1).
2. To clean the fuel injector nozzles, refer to Special Instruction, SEHS7292 for the use of
Tool (B) .
3. Install a new compression seal (2) on the fuel injector nozzle.
Illustration 2 g00448904
4. Use Tool (C) in order to clean the bore in the cylinder head for the fuel injector nozzle. Use
a wrench in order to turn Tool (C) .
2/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00448905
Illustration 4 g00448906
5. Align notch (3) in fuel injector nozzle (5) to the tab in clamp (4) during installation.
6. Install fuel injector nozzle (5). Ensure that the notch in the injector is aligned with the tab in
clamp (4) .
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:14:28 UTC+0800 2019
3/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
Illustration 2 g00460631
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:15:24 UTC+0800 2019
2/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00460737
1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
Illustration 2 g00460791
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00460793
4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
Illustration 4 g00460795
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:16:20 UTC+0800 2019
3/3
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135000
Fuel Ratio Control - Assemble
SMCS - 1278-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the O-ring and the diaphragm. If the O-ring or the diaphragm is
worn or damaged use new parts for replacement.
1/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Illustration 1 g00460801
1. Install spring (1) and retainer (2) into housing (3) .
Illustration 2 g00460828
2. Install O-ring seal (6) and spring (5) into valve extension (7). Install stem (4) into valve
extension (7). Secure valve extension (7) to retainer (8) with nut (9) .
Illustration 3 g00460830
2/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. 3. Install stem (4) and retainer (8) into housing (3) .
Illustration 4 g00460912
4. Install diaphragm (12), washer (11) and spring (10) on retainer (8) .
Illustration 5 g00460914
Illustration 6 g00460917
3/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 5. Install cover (13) on housing (3). Secure cover (13) with two bolts and washers.
6. Install O-ring seal (15) onto cover (14) and install cover (14) onto cover (13). Secure cover
(14) with two bolts.
Note: Refer to Testing and Adjusting, "Fuel System" for additional information on the
adjustment procedure for the fuel ratio control.
End By: Install the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:17:16 UTC+0800 2019
4/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00460631
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
24. Illustration 2 g00460630
2. Put fuel ratio control (1) in position and engage the fuel ratio control with the lever
assembly in the governor.
3. Install bolts (2) that hold the fuel ratio control and connect fuel pressure line (3) to fuel ratio
control (1). Refer to Testing and Adjusting, "Fuel System" for more information on the
adjustment procedure for the fuel ratio control.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:18:11 UTC+0800 2019
2/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00879991
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00475568
1. Remove nut (1) and the washer. Disconnect ground wire (4) from the fuel shutoff solenoid.
2. Remove two nuts (2) and the washers.
1/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. 3. Remove fuel shutoff solenoid (3) and the gasket.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g00475568
1. Install the gasket and fuel shutoff solenoid (3) .
2. Apply 9S-3263 Thread Lock Compound on the threads for two nuts (2) .
3. Install the washers and two nuts (2) .
4. Connect ground wire (4) to the fuel shutoff solenoid. Install nut (1) and the washer.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Wed Sep 11 20:19:07 UTC+0800 2019
2/2
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 225 EXCAVATOR 76U
Configuration: 225 EXCAVATOR 76U00001-00693 (MACHINE)
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00930839
Automatic Timing Advance - Remove
SMCS - 1272-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-7307 Engine Turning Tool 1
B 0T-0065 Bolt 1
C
9S-9155 Spacer 1
8S-2264 Pump Impeller Puller 2
0T-0513 Bolt 2
5P-1075 Hard Washer 2
Start By:
A. Remove the front housing. Refer to Disassembly and Assembly, "Front Housing - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 1. Follow the procedure in Steps 3 and 4 in order to time the fuel injection pump when the
front cover is removed. Follow the procedure in Steps 6 and 7 in order to time the fuel
injection pump when the front cover is installed.
Note: The No. 1 piston should be at the top center position on the compression stroke at the
start of all timing procedures.
Note: The engine is seen from the flywheel end when the direction of the crankshaft
rotation is given.
Illustration 1 g00474593
2. Remove the electric starting motor and install Tool (A) .
Illustration 2 g00474592
3. Turn the crankshaft counterclockwise until the "C" on the crankshaft gear and the "C" on
the camshaft gear are in alignment.
2/4
225 EXCAVATOR 76U00001-00693 (MACHINE)(UEH0804S - 00) - Documentation
2019/9/11
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...