This document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps for disconnecting fuel lines, removing mounting hardware, and ensuring openings are capped to prevent contamination. Required tools are listed for each job. Safety notices emphasize keeping parts clean and containing fluids.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts and washers to detach the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts and washers.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. Installing involves reversing the removal steps - placing the base back on and reconnecting the fuel lines.
3. Removing the fuel injection lines requires disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation reverses this process.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...hvy7sbkw8e
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts and washers to detach the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts and washers.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. Installing involves reversing the removal steps - placing the base back on and reconnecting the fuel lines.
3. Removing the fuel injection lines requires disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation reverses this process.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...xiapokang564341
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Tools required are also listed.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...ufjskmdmdmed
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...zoat27912076
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator. The instructions covered include:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing the idler gear from the front gear group.
- Installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations. Safety and cleaning notes are also included.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
- Instructions reference other documents for removing additional gears.
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components such as the piston guide, pistons, springs, seals, bearings, and housing. It also warns of safety hazards like released spring forces. The assembly procedure is not described but refers to assembling the components in reverse order of disassembly. Proper cleaning and installation of new seals is emphasized to prevent contamination of hydraulic components.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to handle parts carefully and contain fluids.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for disassembling a swing drive. The steps include:
1. Removing various gears, shafts, washers, and bearings from within the swing drive assembly.
2. Using retaining ring pliers and a driver group to remove retaining rings and pins.
3. Pressing out bearings, seals, and a shaft from the swing drive housing.
4. Removing a ring gear, carrier assembly, and cage from the housing.
The purpose is to fully disassemble the swing drive for repair or replacement of parts. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...wenxian17880
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components. This includes removing bolts, seals, plates, springs, pistons, and bearings. Cleanliness is emphasized to prevent contamination. The document then lists the assembly procedure, but does not provide the specific steps, instead stating to reverse the disassembly process. Proper torque values and identification marks are recommended for correct reassembly.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...wenxian17880
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety and contamination prevention notices are also included.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...wenxian17880
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and apply retaining compounds as needed.
3. Safety notices are provided to contain fluids and wear protective gloves when handling hot parts.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...wenxian17880
The document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on an excavator model 320C. It involves connecting pilot lines, hoses, electrical connectors, and mounting the control valves. Tools like a vacuum cap are used to minimize hydraulic fluid leakage during installation. High efficiency hydraulic filters are installed before filling the tank and swing drive with clean hydraulic oil.
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
The document provides instructions for removing and disassembling a travel motor from an excavator model 320C. It involves draining oil, removing bolts and hoses, lifting the motor out using threaded rods and a lifting device, and then disassembling internal components like the head, spool, springs, seals and pistons using various specialty tools. Cleanliness is emphasized to prevent contamination of hydraulic components during disassembly and reassembly.
More Related Content
Similar to Caterpillar Cat 320C Excavator (Prefix GNG) Service Repair Manual (GNG00001 and up).pdf
Caterpillar Cat 320C S 320CS Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Special tools may be required and safety precautions are noted.
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components included are the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures provide detailed steps that include required tools, removal steps, and installation steps for each component. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar Cat 320C L 320CL Excavator (Prefix BCN) Service Repair Manual (BC...wenxian17880
This document provides instructions for removing and installing various fuel system components on a 320C excavator model powered by a 3066 engine. The components include the fuel filter base, fuel injection lines, fuel injection nozzles, fuel shutoff solenoid, and fuel injection pump. The procedures describe disconnecting fuel lines, removing mounting hardware, and ensuring openings are plugged to prevent contamination. Tools required are also listed.
This document provides instructions for removing and installing the fuel filter base and fuel injection lines on a Caterpillar 320C excavator with a 3066 engine. The summary is:
1. The removal procedure describes disconnecting the fuel lines from the fuel filter base and filter, and removing two bolts to take off the base.
2. The installation procedure outlines reconnecting the fuel lines to the base and filter, and securing the base with two bolts.
3. Removing the fuel injection lines involves disconnecting them from the nozzles and pump, and removing mounting bolts and clamps. Installation is the reverse of removal.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...fusjekkdmdmd2w
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...ufjskmdmdmed
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
Caterpillar Cat 320C L 320CL Excavator (Prefix GNG) Service Repair Manual (GN...zoat27912076
The document provides instructions for removing and installing fuel injection nozzles on a Caterpillar 320C excavator engine. Key steps include:
1. Removing the fuel injection lines, fuel filter base, and clamps securing the nozzles. Caps must be installed to prevent contamination.
2. Using puller tools attached to the nozzle and fuel line connection point to carefully extract each nozzle.
3. Cleaning all parts and installing the nozzles by reversing the removal steps, taking care to prevent contamination of the fuel system.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Similar to Caterpillar Cat 320C Excavator (Prefix GNG) Service Repair Manual (GNG00001 and up).pdf (10)
Caterpillar Cat 320C U Excavator (Prefix PAC) Service Repair Manual (PAC00001...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator. The instructions covered include:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing the crankshaft front seal.
- Removing the idler gear from the front gear group.
- Installing the idler gear.
The document provides detailed step-by-step instructions accompanied by illustrations. Safety and cleaning notes are also included.
Caterpillar Cat 320C LU 320CLU Excavator (Prefix PAC) Service Repair Manual (...wenxian17880
This document provides instructions for removing and installing various engine components on a Caterpillar 320C excavator engine, including:
- Removing and installing the flywheel housing.
- Removing and installing the crankshaft pulley.
- Removing the crankshaft front seal.
- Installing a new crankshaft front seal.
- Removing the idler gear from the front gear group.
- Instructions reference other documents for removing additional gears.
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components such as the piston guide, pistons, springs, seals, bearings, and housing. It also warns of safety hazards like released spring forces. The assembly procedure is not described but refers to assembling the components in reverse order of disassembly. Proper cleaning and installation of new seals is emphasized to prevent contamination of hydraulic components.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety notices are included to handle parts carefully and contain fluids.
This document provides instructions for removing and installing the engine oil pump on a Caterpillar 320C LN excavator. It outlines 10 steps to remove the pump, including removing the front housing, cover, gears, seals and spindle. It then outlines 8 steps to install the pump, including heating components, installing seals, gears and the cover. Safety notices are provided regarding keeping components clean and containing fluids.
The document provides instructions for disassembling a swing drive. The steps include:
1. Removing various gears, shafts, washers, and bearings from within the swing drive assembly.
2. Using retaining ring pliers and a driver group to remove retaining rings and pins.
3. Pressing out bearings, seals, and a shaft from the swing drive housing.
4. Removing a ring gear, carrier assembly, and cage from the housing.
The purpose is to fully disassemble the swing drive for repair or replacement of parts. Cleanliness is emphasized to prevent contamination of hydraulic components.
Caterpillar Cat 320C L Excavator (Prefix JTG) Service Repair Manual (JTG00001...wenxian17880
The document provides instructions for disassembling and assembling the travel motor of a 320C excavator. It lists 28 steps for disassembling the travel motor into individual components. This includes removing bolts, seals, plates, springs, pistons, and bearings. Cleanliness is emphasized to prevent contamination. The document then lists the assembly procedure, but does not provide the specific steps, instead stating to reverse the disassembly process. Proper torque values and identification marks are recommended for correct reassembly.
Caterpillar Cat 320C L Excavator (Prefix DBG) Service Repair Manual (DBG00001...wenxian17880
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety and contamination prevention notices are also included.
Caterpillar Cat 320C L 320CL Excavator (Prefix RAW) Service Repair Manual (RA...wenxian17880
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and apply retaining compounds as needed.
3. Safety notices are provided to contain fluids and wear protective gloves when handling hot parts.
Caterpillar Cat 320C L 320CL Excavator (Prefix HKT) Service Repair Manual (HK...wenxian17880
The document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on an excavator model 320C. It involves connecting pilot lines, hoses, electrical connectors, and mounting the control valves. Tools like a vacuum cap are used to minimize hydraulic fluid leakage during installation. High efficiency hydraulic filters are installed before filling the tank and swing drive with clean hydraulic oil.
1. The document provides instructions for removing and installing various engine components on Caterpillar 320C and 320C L excavators, including the flywheel, crankshaft rear seal, flywheel housing, and crankshaft pulley.
2. The procedures describe using various tools to remove parts and installing replacement parts, taking care to keep parts clean and applying retaining compounds as specified.
3. Detailed illustrations accompany each procedure to show the component locations and installation/removal steps.
The document provides instructions for removing and disassembling a travel motor from an excavator model 320C. It involves draining oil, removing bolts and hoses, lifting the motor out using threaded rods and a lifting device, and then disassembling internal components like the head, spool, springs, seals and pistons using various specialty tools. Cleanliness is emphasized to prevent contamination of hydraulic components during disassembly and reassembly.
This document provides instructions for removing and installing track components on a 320C excavator. It describes:
1) Releasing track tension and removing the track carrier roller or track roller using hydraulic jacks and lifting tools.
2) Cleaning mounting surfaces and installing the components using lifting devices, making sure rollers rotate smoothly.
3) Separating the track by removing the master pin and spacers after releasing tension and placing a block under the track.
The document provides installation instructions for auxiliary control valves F1, F4, F2, and F3 on an excavator model 320C. It involves connecting pilot lines, hoses, electrical connectors, and mounting the control valves. Tools like a vacuum cap are used to minimize hydraulic fluid leakage during installation. High efficiency hydraulic filters are installed before filling the tank and swing drive with clean hydraulic oil.
This document provides instructions for removing and installing fuel injection lines, nozzles, and pumps on a Caterpillar 3066 engine. It describes disconnecting the lines from the fuel injection pump, nozzles, and manifold. It also details using puller tools to remove nozzles and ensuring caps are used to prevent contamination. Proper alignment of parts and torquing of bolts is emphasized during installation.
The document provides instructions for disassembling a swing drive. The steps include:
1. Removing various gears, shafts, washers, and bearings from within the swing drive assembly.
2. Using retaining ring pliers and a driver group to remove retaining rings and pins.
3. Pressing out bearings and seals from the swing drive housing.
4. Marking the swing drive location prior to removal for installation purposes.
This document provides instructions for removing and installing various engine components on Caterpillar 320C excavators, including the flywheel, crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The procedures describe using various tools to remove and install each part, providing illustrations to supplement the text instructions. Safety and contamination prevention notices are also included.
This document provides instructions for removing and installing various actuator motors and sensors on a 320C excavator. It includes procedures for removing and installing the actuator motor for the air damper for temperature control, front air damper, fresh air/recirculated air damper, rear window defroster, and front window. It also includes instructions for removing and installing the fan speed control, ambient air temperature sensor, and coolant temperature sensor. The procedures provide illustrations and numbered steps for disconnecting wiring, removing mounting hardware, and replacing components.
The document provides instructions for removing and installing inlet and exhaust valve springs on Caterpillar 3064 and 3066 engines. It outlines the required tools and safety precautions. The procedure describes using an air compressor tool to hold the valves in position while removing and installing the springs, in order to perform the task without removing the cylinder head. Instructions include compressing the valve springs using an adapter tool, removing the valve spring retainers, and installing new springs.
Caterpillar Cat 308E2SR Mini Hydraulic Excavator (Prefix SR8) Service Repair ...wenxian17880
The document provides instructions for removing and installing various components of a 308E2SR Mini Hydraulic Excavator, including the electronic unit injector, turbocharger, mass air flow pressure sensor, exhaust gas recirculation valve, and fumes disposal filter. The procedures include illustrations of the components and steps to disconnect hoses, remove mounting hardware, and install replacement parts in the reverse order of removal. Safety notices are also provided regarding working on pressurized fuel and cooling systems.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Your VW's camshaft position sensor is crucial for engine performance. Signs of failure include engine misfires, difficulty starting, stalling at low speeds, reduced fuel efficiency, and the check engine light. Prompt inspection and replacement can prevent further damage and keep your VW running smoothly.
What Is Recruitment Processing Outsourcing (RPO) Services?Impeccable HR
Impeccable HR provides a wide range of RPO services for your bulk hiring needs within a stipulated period. They meticulously build RPO solutions to improve your recruitment process. RPO services are great for budget-conscious recruiters who want high-quality personnel.
Comprehensive program for Agricultural Finance, the Automotive Sector, and Empowerment . We will define the full scope and provide a detailed two-week plan for identifying strategic partners in each area within Limpopo, including target areas.:
1. Agricultural : Supporting Primary and Secondary Agriculture
• Scope: Provide support solutions to enhance agricultural productivity and sustainability.
• Target Areas: Polokwane, Tzaneen, Thohoyandou, Makhado, and Giyani.
2. Automotive Sector: Partnerships with Mechanics and Panel Beater Shops
• Scope: Develop collaborations with automotive service providers to improve service quality and business operations.
• Target Areas: Polokwane, Lephalale, Mokopane, Phalaborwa, and Bela-Bela.
3. Empowerment : Focusing on Women Empowerment
• Scope: Provide business support support and training to women-owned businesses, promoting economic inclusion.
• Target Areas: Polokwane, Thohoyandou, Musina, Burgersfort, and Louis Trichardt.
We will also prioritize Industrial Economic Zone areas and their priorities.
Sign up on https://profilesmes.online/welcome/
To be eligible:
1. You must have a registered business and operate in Limpopo
2. Generate revenue
3. Sectors : Agriculture ( primary and secondary) and Automative
Women and Youth are encouraged to apply even if you don't fall in those sectors.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564836
Fuel Filter Base - Remove and Install
SMCS - 1262-010
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 185-3630 Strap Wrench Assembly 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
1/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
3. Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00813127
1. Use Tool (A) to remove fuel filter (3) from fuel filter base (2) .
Note: It is not necessary to remove the fuel filter in order to remove the fuel filter base.
2. Remove banjo bolts (1) and copper washers in order to disconnect the fuel lines (4) from the
fuel filter base (2).
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
Illustration 2 g00813147
3. Remove two bolts (5) and the washers that secure the fuel filter base (2) to the air inlet
manifold. Remove the fuel filter base (2) from the fuel filter bracket.
Installation Procedure
2/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
5. NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 3 g00813147
1. Place the fuel filter base (2) in position on the fuel filter bracket. Install the washers and two
bolts (5) that secure the fuel filter base tothe fuel filter bracket.
Illustration 4 g00813127
2. Install the banjo bolts (1) and install new copper washers in order to connect the fuel lines
(4) to the fuel filter base (2) .
3. If the fuel filter was removed, install the fuel filter (3) to the fuel filter base (2). Tighten the
fuel filter by hand according to the instructions that are shown on the fuel filter. Do not
overtighten the fuel filter.
3/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
6. Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:40:53 UTC+0800 2019
4/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565021
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
Start By:
A. Remove the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
8. Illustration 1 g00606301
The 3066 Engine is shown.
1. Remove the bolts (1), the washers, and the clamps (2), which secure the fuel lines to the
inlet manifold (3) .
Illustration 2 g00606310
2. Disconnect the fuel injection lines (4) from the fuel injection nozzles (5) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
2/5(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
9. Illustration 3 g00606314
Fuel injection pump for a 3066 Engine
3. Disconnect the end of the fuel injection lines (4) from the fuel injection pump (6) .
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
4. Remove the fuel injection lines (4) from the engine.
Illustration 4 g00606317
5. Loosen the acorn nuts (7), which secure the fuel return line to the fuel injection nozzles.
6. Remove one bolt (8) and the washer from the clamp that secures the fuel return line to the
intake manifold.
Note: The clamp will remain with the fuel return line, when the fuel return line is removed
from the engine.
7. Disconnect fitting (9). Remove fuel return line (10) from the engine.
Note: Cap all openings or plug all openings immediately in order to prevent contamination
of the fuel system.
3/5(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
10. Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 5 g00606317
1. Place the fuel return line (10) in position on the engine. Connect fitting (9) of the fuel return
line to the fuel injection pump.
2. Install the washer and bolt (8) through the clamp in order to secure the fuel return line to the
inlet manifold.
3. Install the fuel return line (10) to the fuel injection nozzles. Secure the fuel return line to the
fuel injection nozzle with acorn nuts (7) .
4/5(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
11. Illustration 6 g00606399
Fuel injection pump for a 3066 Engine
4. Place the fuel injection lines (4) on the engine.
5. Connect the fuel injection lines (4) to the fuel injection pump (6) .
6. Connect the fuel injection lines (4) to the fuel injection nozzles (5) .
Note: The fuel lines (4) should be connected at the fuel injection nozzle (5) and at the fuel
injection pump (6) before tightening the nuts for the fuel injection line.
7. Tighten the nuts for the fuel injection line to a torque of 25 N·m (18 lb ft).
Illustration 7 g00606301
Fuel lines for a 3066 Engine
8. Install the clamps (2), the washers, and the bolts (1), which secure the fuel lines to the inlet
manifold (3) .
End By: Install the fuel filter base. Refer to Disassembly and Assembly, "Fuel Filter Base -
Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:41:49 UTC+0800 2019
5/5(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
12. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151321
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1U-7600 Slide Hammer Puller 1
B 9U-6278 Adapter 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
13. Illustration 1 g00652319
1. Remove bolt (1) and the washer that secures the clamp (2) to the cylinder head assembly.
2. Remove the clamp (2) that secures the fuel injection nozzle (3) in position in the cylinder
head assembly.
Note: Put caps or plugs on all openings immediately in order to prevent contamination in
the fuel system.
Note: Mark the clamp for later installation.
3. Install Tool (B) (not shown) to the fuel injection nozzle.
Note: Tool (B) is installed at the connection (4) for the fuel injection lines.
4. Connect Tool (A) (not shown) to Tool (B) in order to carefully remove fuel injection nozzle
(3) .
Note: Align the centerline of Tool (A) with the extended centerline of fuel injection nozzle
(3). This procedure will help prevent distortion of the fuel injection nozzle which can cause
the fuel injection nozzle to bend or break.
5. Remove the seat washer from the fuel injection nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:42:44 UTC+0800 2019
2/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
14. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01151648
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00652319
1/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
15. 1. Install a new seat washer (5) .
2. Install fuel injection nozzle (3).
3. Install clamp (2), the washer, and bolt (1) that secures the fuel injection nozzle to the
cylinder head assembly.
4. Tighten bolt (1), that secures the fuel injection nozzle, to a torque of 22 N·m (16 lb ft).
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:43:40 UTC+0800 2019
2/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615152
Fuel Shutoff Solenoid - Remove and Install
SMCS - 1259-010
Removal Procedure
Illustration 1 g00618938
1. Disconnect two wire leads (1). Mark the wires for later installation.
2. Disconnect actuator lever (2) from the governor lever.
3. Remove two bolts (3) and washers that secure the fuel shutoff solenoid to the bracket.
4. Remove shutoff solenoid (4) from the bracket.
Installation Procedure
1/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
17. Illustration 2 g00618938
1. Place the shutoff solenoid (4) in position on the bracket.
2. Install the two washers and bolts (3) that secure the fuel shutoff solenoid to the bracket.
3. Connect actuator lever (2) to the governor lever.
4. Connect two wire leads (1) to the fuel shutoff solenoid. Ensure that the wires are properly
connected.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:44:36 UTC+0800 2019
2/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
18. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565175
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
1/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
19. of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Ensure that the engine is the top center position on number one piston. Refer to Testing and
Adjusting, "Finding Center Position for No. 1 Piston".
Illustration 1 g00813442
2. Remove bolts (1) and washers that secure the cover (2) to the engine front housing.
3. Remove the access cover. Note the timing marks on the fuel injection pump drive gear and
the idler gear for later installation.
Illustration 2 g00813430
2/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
20. 4. Scribe a line across the front plate (3) and the mounting flange for the fuel injection pump
(4). This ensures proper alignment for the installation of fuel injection pump (8) .
5. Loosen fitting (5) for oil line (6) .
6. Remove oil line (6) from nipple (7) (not shown).
Note: Put caps or plugs on all openings immediately in order to prevent contamination.
7. Use a lifting sling and a hoist in order to secure the fuel injection pump. The weight of the
fuel injection pump is 13 kg (29 lb).
Note: Use Tool (B) to remove the bolts and the washers that mount the fuel injection pump
(8) .
8. Remove bolt (9) and the washer from the cylinder block.
9. Remove four bolts (10) and the washers that secure the fuel injection pump to the front
housing.
Illustration 3 g00813593
10. Remove the fuel injection pump (8). The gear and the mounting flange will remain with the
fuel injection pump.
Note: The fuel injection pump must be mounted to the engine in order to loosen the nut for
the drive gear.
Note: Do not rotate the engine after the fuel injection pump is removed.
11. Ensure that the old gasket material is removed from all mating surfaces of the pump
mounting flange and the face of the fuel injection pump flange.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:45:32 UTC+0800 2019
3/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
21. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01565619
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part number Part Description Qty
A 9U-6124 Universal Metric Socket Set 1
B 9U-6128 Universal Metric Socket (1)
1
( 1 )
Part of the Universal Metric Socket Set
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: If the nut for the fuel injection pump drive gear is removed, you must tighten the nut
for the fuel injection pump drive gear to 88 ± 5 N·m (65 ± 4 lb ft).
1/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
22. Illustration 1 g00813430
1. Use a lifting sling and a hoist in order to secure the fuel injection pump (8). The weight of
the fuel injection pump is 13 kg (29 lb).
2. Install a new gasket and install fuel injection pump (8) .
3. Ensure that the engine is in the top center position on No. 1 piston. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
4. Ensure that the mark on the front plate (3) and the mark on the fuel injection pump flange
(4) are aligned.
Refer to Testing and Adjusting, "Fuel Injection Timing-Check" for more information on
fuel injection pump timing.
Note: Use Tool (B) to install the bolts and washers that secure the fuel injection pump to the
cylinder block.
5. Install the washers and bolts (9) that secure the fuel injection pump to the engine cylinder
block.
6. Remove the sling from the fuel injection pump.
7. Connect oil line (6) to nipple (7) (not shown).
8. Tighten fitting (5) for oil line (6) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:46:28 UTC+0800 2019
2/2(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01564499
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
24. Illustration 1 g00608136
1. Loosen the hose clamp (1) on hose (2) .
2. Remove hose (2) from the turbocharger (3) .
Illustration 2 g00812846
3. Disconnect oil supply line (4) from the cylinder block.
4. Loosen two clamps (5) on hose (7) .
5. Slide hose (7) off fitting (8) onto oil return line (6) .
2/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
25. Illustration 3 g00608177
6. Remove eight nuts (9) from the studs on the exhaust manifold.
Note: The four studs have two nuts for a total of eight nuts.
7. Remove turbocharger (3), oil supply line (4), and oil return line (6) as an unit.
8. Remove metal gasket (10) (not shown). Check the gasket for wear or damage. Replace the
gasket, if necessary.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:47:24 UTC+0800 2019
3/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01615171
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
27. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
28. 1. Place an index mark on all of the components. The marks will help to align the components
during the assembly procedure.
Illustration 1 g00608212
2. Remove two bolts (1) from the oil return line. Remove bolt (2) from the oil supply line.
3. Remove oil return line (3) from the cartridge.
4. Remove oil supply line (4) from the cartridge.
Illustration 2 g00608210
5. Remove gasket (5) from the cartridge.
6. Remove gasket (6) from the turbine housing.
2/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
29. Illustration 3 g00608342
7. Remove the bolt and nut (7) from clamp (8). Remove clamp (8) that secures the turbine
housing (9) to the cartridge (10) .
8. Separate turbine housing (9) from the cartridge (10) .
Illustration 4 g00608415
Illustration 5 g00608452
3/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
30. 9. Remove snap ring (11) from compressor housing (12) .
10. Separate compressor housing (12) from the cartridge (10) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 20 08:48:19 UTC+0800 2019
4/4(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...
31. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 320C EXCAVATOR GNG
Configuration: 320C & 320C L Excavators GNG00001-UP (MACHINE) POWERED BY 3066 Engine
Disassembly and Assembly
3064 and 3066 Engines for Caterpillar Built Machines
Media Number -SENR5553-10 Publication Date -01/05/2012 Date Updated -15/05/2012
i01147762
Turbocharger - Assemble
SMCS - 1052-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: During the assembly procedure, ensure that the index marks are aligned when the
components are assembled.
Illustration 1 g00608452
1/3(W)
w
2019/9/20
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sisweb/sisw...