This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjsjjefkskekm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...uujfjjskkdme
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B or 3306B engine. The removal procedure involves removing various lines, bolts, washers and other components to separate the housing. The disassembly process then describes dismantling internal parts like the camshaft, bearings and lifters. Reassembly involves cleaning and lubricating parts before reinstalling them in reverse order.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
This document provides instructions for removing and installing components on a Caterpillar 3034 engine, including:
- Removing the fuel injection pump by disconnecting linkages, removing mounting bolts and shims, and ensuring dowels and pins are not damaged.
- Installing the fuel injection pump by cleaning surfaces, positioning shims, aligning dowels and pins, and tightening mounting bolts.
- Removing the turbocharger by disconnecting hoses, removing mounting nuts and bolts, and removing it and the gasket.
- Installing the turbocharger by positioning the gasket and turbocharger, tightening mounting nuts, and reconnecting hoses.
- Removing the exhaust manifold
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fusjejfskekfmsme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a tool with the camshaft groove to bring the pump to the timed position.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjsjjefkskekm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 225 d lc excavator (prefix 6rg) service repair manual (6rg000...uujfjjskkdme
This document provides instructions for disassembling and assembling the fuel injection pump housing of a Caterpillar 3304B or 3306B engine. The removal procedure involves removing various lines, bolts, washers and other components to separate the housing. The disassembly process then describes dismantling internal parts like the camshaft, bearings and lifters. Reassembly involves cleaning and lubricating parts before reinstalling them in reverse order.
This document provides instructions for removing and installing piston rings and connecting rod bearings on a Caterpillar 3306 engine. It describes the required tools and steps to disassemble pistons and connecting rods, including removing piston rings, piston pins, and bearings. It then explains how to assemble pistons and connecting rods, including cleaning parts, installing bearings, rings, piston pins, and connecting rods. Finally, it describes installing the pistons and connecting rods back into the engine.
This document provides instructions for removing and installing a unit injector, unit injector sleeve, and turbocharger from a C9.3 Industrial Engine. The unit injector removal procedure involves disconnecting electrical and fuel lines, loosening mounting bolts, and extracting the injector. Installation requires cleaning, lubricating seals, and tightening bolts. The sleeve procedure includes draining coolant, cutting threads to remove the old sleeve, cleaning the bore, applying retaining compound to the new sleeve, and installing with a hammer and driver. The turbocharger removal involves disconnecting coolant and air lines and removing mounting nuts. Installation requires applying anti-seize to bolts and tightening clamps and nuts.
This document provides instructions for removing and installing components on a Caterpillar 3034 engine, including:
- Removing the fuel injection pump by disconnecting linkages, removing mounting bolts and shims, and ensuring dowels and pins are not damaged.
- Installing the fuel injection pump by cleaning surfaces, positioning shims, aligning dowels and pins, and tightening mounting bolts.
- Removing the turbocharger by disconnecting hoses, removing mounting nuts and bolts, and removing it and the gasket.
- Installing the turbocharger by positioning the gasket and turbocharger, tightening mounting nuts, and reconnecting hoses.
- Removing the exhaust manifold
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fusjejfskekfmsme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a tool with the camshaft groove to bring the pump to the timed position.
This service repair manual provides instructions for removing and installing the exhaust manifold and inlet/exhaust valves on a Caterpillar 3306 engine. It details the necessary tools and steps, including:
1) Removing the exhaust manifold by taking off nuts and bolts, fuel lines, and gaskets.
2) Installing a new exhaust manifold by positioning gaskets and bolts and tightening to the specified torque.
3) Removing inlet/exhaust valves using a valve spring compressor and identifying valves.
4) Installing new valves by lubricating, positioning springs and keepers, and ensuring proper installation.
Caterpillar Cat 235 EXCAVATOR (Prefix 62X) Service Repair Manual (62X00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It describes:
- Removing fuel injection line brackets and disconnecting lines from the fuel pumps and nozzles
- Installing lines by tightening nuts to the specified torque and replacing brackets
- Removing nozzles using special tools to prevent damage and removing sealing components
- Cleaning and installing nozzles with new seals, ensuring notches are aligned
- Removing the fuel ratio control by disconnecting lines and moving it out of the governor lever assembly
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It outlines the necessary tools and safety precautions. The procedure involves removing brackets and disconnecting nuts to remove the lines, and reversing the steps to install new lines, ensuring nozzles are properly supported and tightened to the specified torque. Cleaning tools are also described for cleaning nozzles and cylinder bores.
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. The removal process involves disconnecting nuts and brackets to remove the lines and using special tools to pull nozzles while preventing them from turning. Installation requires cleaning parts, adding new seals, and reconnecting lines and brackets while applying specified torques. Proper alignment of notches and tabs is important when reinstalling nozzles.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. It describes:
- Removing three bolts and brackets from the fuel injection lines and disconnecting nuts from the lines and nozzles.
- Installing the lines by tightening nuts with a specified tool to the correct torque at the pumps and nozzles.
- Removing nozzles using special puller tools, being careful not to damage them.
- Cleaning and installing nozzles with compression seals using additional specialized tools.
This document provides instructions for removing and installing fuel injection lines, fuel injector nozzles, and a fuel ratio control on a Caterpillar 225 excavator engine. The procedures include removing brackets and disconnecting nuts to remove the lines, using specialized tools to pull the nozzles, and removing bolts and seals to take off the fuel ratio control. Technicians are advised to keep parts clean and contain fluids during disassembly.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjkskefkemm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...uudfjjjskkemmd
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...uujjfjjkskmme
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...yhfhjjkdksmme
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and tighten bolts and clamps.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsjefskekmm
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and properly cap openings to prevent contamination. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...ujjfdjkjskkmdm
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reconnecting lines and nozzles in reverse order using new seals and following tightening specifications.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...fujsjefkksekmme
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and correctly install replacement parts. Safety notices are included to prevent contamination of fuel system components.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...fujsfskekem
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and correctly install replacement parts. Safety notices are included to prevent contamination of fuel system components.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsefjfkksekem
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and securely tighten all bolts and clamps. Proper cleaning prevents rapid wear and failure of fuel system components.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fujjsekskemme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a timing pin with the camshaft groove to set the pump in the top center position.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fsejfjskefsmem
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a timing pin with the camshaft groove to set the pump in the top center position.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fjksekkmsemm
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a tool with the camshaft groove to bring the pump to the timed position.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
New holland w80 tc wheel loader service repair manualfusjejfkskemme
The document is a repair manual that provides instructions and specifications for servicing and repairing various components of wheel loaders models W50TC, W60TC, W70TC and W80TC. It covers topics such as the diesel engine, fuel system, front and rear axles, brakes, hydraulic and electrical systems, frame, steering, heating and air conditioning, and working equipment. Safety precautions are outlined at the beginning, emphasizing the importance of following instructions for safe operation and maintenance.
New holland w80 c hs tier 4b (final) compact wheel loader service repair manualfusjejfkskemme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
More Related Content
Similar to Caterpillar cat 235 excavator (prefix 62 x) service repair manual (62x00001 00288)
Caterpillar Cat 235 EXCAVATOR (Prefix 62X) Service Repair Manual (62X00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It describes:
- Removing fuel injection line brackets and disconnecting lines from the fuel pumps and nozzles
- Installing lines by tightening nuts to the specified torque and replacing brackets
- Removing nozzles using special tools to prevent damage and removing sealing components
- Cleaning and installing nozzles with new seals, ensuring notches are aligned
- Removing the fuel ratio control by disconnecting lines and moving it out of the governor lever assembly
This document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 3306 engine. It outlines the necessary tools and safety precautions. The procedure involves removing brackets and disconnecting nuts to remove the lines, and reversing the steps to install new lines, ensuring nozzles are properly supported and tightened to the specified torque. Cleaning tools are also described for cleaning nozzles and cylinder bores.
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. The removal process involves disconnecting nuts and brackets to remove the lines and using special tools to pull nozzles while preventing them from turning. Installation requires cleaning parts, adding new seals, and reconnecting lines and brackets while applying specified torques. Proper alignment of notches and tabs is important when reinstalling nozzles.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
The document provides instructions for removing and installing fuel injection lines, fuel injection nozzles, and a fuel ratio control on a 225 excavator. The procedures include disconnecting nuts and lines, using specialty tools to remove parts, cleaning components, and ensuring proper installation of seals and fittings. Technicians are advised to take care to avoid contaminating parts and properly contain fluids.
Caterpillar Cat 225 EXCAVATOR (Prefix 76U) Service Repair Manual (76U00001-00...jfkksemmdmd
This document provides instructions for removing and installing fuel injection lines and nozzles on a 225 EXCAVATOR model. It describes:
- Removing three bolts and brackets from the fuel injection lines and disconnecting nuts from the lines and nozzles.
- Installing the lines by tightening nuts with a specified tool to the correct torque at the pumps and nozzles.
- Removing nozzles using special puller tools, being careful not to damage them.
- Cleaning and installing nozzles with compression seals using additional specialized tools.
This document provides instructions for removing and installing fuel injection lines, fuel injector nozzles, and a fuel ratio control on a Caterpillar 225 excavator engine. The procedures include removing brackets and disconnecting nuts to remove the lines, using specialized tools to pull the nozzles, and removing bolts and seals to take off the fuel ratio control. Technicians are advised to keep parts clean and contain fluids during disassembly.
Caterpillar cat 160 g motor grader (prefix 4jd) service repair manual (4jd000...fjkskefkemm
This document provides instructions for removing and installing fuel injection lines and nozzles on a 160G motor grader. It describes:
1) Removing fuel injection line nuts and brackets to disconnect the lines from the fuel injection pumps and nozzles.
2) Installing the lines by reconnecting the nuts and tightening them to the specified torque, and replacing the brackets.
3) Removing fuel injection nozzles using special puller tools to lift them out of the cylinder head bores.
4) Installing new carbon seals and compression seals on the nozzles before reinserting them into the bores.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...uudfjjjskkemmd
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...uujjfjjkskmme
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and secure nozzles with clamps and bolts.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...yhfhjjkdksmme
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and tighten bolts and clamps.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsjefskekmm
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and properly cap openings to prevent contamination. Safety notices are also included to keep parts clean and contain fluids.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...ujjfdjkjskkmdm
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reconnecting lines and nozzles in reverse order using new seals and following tightening specifications.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...fujsjefkksekmme
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and correctly install replacement parts. Safety notices are included to prevent contamination of fuel system components.
Caterpillar cat 320 c excavator (prefix gng) service repair manual (gng00001 ...fujsfskekem
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing new fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures provide detailed steps and illustrations for each component, describing how to disconnect lines, remove mounting hardware, and correctly install replacement parts. Safety notices are included to prevent contamination of fuel system components.
Caterpillar cat 320 c l 320cl excavator (prefix gng) service repair manual (g...fujsefjfkksekem
1. The document provides instructions for removing and installing fuel injection lines and nozzles on a Caterpillar 320C excavator engine.
2. Key steps include removing bolts and clamps to disconnect lines from the fuel filter base, injection pump, and nozzles. Lines and nozzles are then removed and openings are capped to prevent contamination.
3. Reinstallation involves cleaning parts, recapping openings, and reversing the removal procedures to reconnect lines and securely tighten all bolts and clamps. Proper cleaning prevents rapid wear and failure of fuel system components.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fujjsekskemme
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a timing pin with the camshaft groove to set the pump in the top center position.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fsejfjskefsmem
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a timing pin with the camshaft groove to set the pump in the top center position.
Caterpillar cat 225 b excavator (prefix 3yd) service repair manual (3yd00001 up)fjksekkmsemm
This document provides instructions for installing a fuel injection pump housing and governor on a Caterpillar 3304B or 3306B engine. The steps include:
1. Using a tool to find the top center position of the No. 1 piston to time the installation.
2. Installing a tool into the flywheel housing and turning the flywheel to locate top center.
3. Installing the fuel injection pump housing, aligning a tool with the camshaft groove to bring the pump to the timed position.
The document provides instructions for removing and installing various fuel system components on a Caterpillar 320C excavator engine, including:
- Removing and installing the fuel filter base.
- Removing and installing the fuel injection lines.
- Removing the fuel injection nozzles.
- Installing the fuel injection nozzles.
- Removing and installing the fuel shutoff solenoid.
- Removing the fuel injection pump.
The procedures describe disconnecting fuel lines, removing mounting bolts and brackets, and ensuring openings are capped to prevent contamination. Required tools are listed for each job.
Similar to Caterpillar cat 235 excavator (prefix 62 x) service repair manual (62x00001 00288) (20)
New holland w80 tc wheel loader service repair manualfusjejfkskemme
The document is a repair manual that provides instructions and specifications for servicing and repairing various components of wheel loaders models W50TC, W60TC, W70TC and W80TC. It covers topics such as the diesel engine, fuel system, front and rear axles, brakes, hydraulic and electrical systems, frame, steering, heating and air conditioning, and working equipment. Safety precautions are outlined at the beginning, emphasizing the importance of following instructions for safe operation and maintenance.
New holland w80 c hs tier 4b (final) compact wheel loader service repair manualfusjejfkskemme
This document is a service manual for New Holland compact wheel loaders W50C, W60C, W70C, and W80C. It contains instructions for repair and maintenance work to be performed only by qualified dealership personnel. The manual provides information on the engine, transmission, front and rear axle systems, brakes and controls, hydraulic systems, frames and ballasting, steering, and electrical systems of the loaders. Proper procedures are outlined for tasks like shimming, installing rotating shaft seals, applying sealing compounds, and protecting electronic systems during charging and welding.
New holland w80 c hs tier 4 compact wheel loader service repair manualfusjejfkskemme
This document provides instructions for removing an engine from a compact wheel loader. It describes disconnecting wiring harnesses and hoses, draining fluids, securing the engine hood with a lifting strap, removing mounting bolts, and carefully raising and removing the engine hood to access the engine. Proper safety procedures and steps to isolate energy sources are outlined.
New holland w70 tc wheel loader service repair manualfusjejfkskemme
This document is a repair manual that provides instructions and specifications for servicing various components of W50TC, W60TC, W70TC, and W80TC wheel loaders. It includes sections on the engine, front and rear axles, brakes system, and hydraulic system. The manual contains diagrams, dimensions, technical specifications, disassembly/assembly instructions, troubleshooting guides, and lists of special tools needed for repairs.
New holland w70 c hs stage iiib compact wheel loader service repair manualfusjejfkskemme
This document is a service manual for CNH Industrial Italia S.p.A. compact wheel loaders models W50C, W60C, W70C, and W80C. It contains sections on the engine, four-wheel drive system, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, steering, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. The manual provides repair and maintenance instructions for technicians and mechanics.
New holland w60 wheel loader service repair manualfusjejfkskemme
This workshop manual provides instructions for repairing wheel loaders. It outlines safety procedures and contains sections covering the diesel engine, transmission, axles, steering, brake system, hydraulic system, electrical system, frame, and other components. Technicians should carefully follow the repair instructions and use only original spare parts to safely and properly service the wheel loaders.
New holland tc5080 hillside combine harvesters service repair manualfusjejfkskemme
The primary hydraulic power system for the TC5000 series combines includes two pumps without lateral flotation and three pumps with lateral flotation. Key components are the main hydraulic pump, steering pump, optional lateral flotation pump, oil tank, filters, valve stack including controls for header height, unloading tube, reel, and optional lateral flotation. Other components are the header lift cylinders, accumulator control valve, steering valve, cylinders for steering and optional lateral flotation, and rotary union for the straw chopper clutch.
New holland tc5070 hillside combine harvesters service repair manualfusjejfkskemme
This service manual provides information on servicing various components of TC5040, TC5050, TC5060, TC5070, TC5070, TC5080 Hillside, and TC5080 combines. The manual covers engines, transmissions, brakes, hydraulic systems, electrical systems, attachments, feeding, threshing, separation, cleaning, and other systems. Repair and maintenance should only be performed by trained technicians using the proper tools and approved parts. Unauthorized repairs may affect warranty coverage and product safety.
New holland tc5.90 fpt nef 6 stage iv combine harvester service repair manualfusjejfkskemme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland tc5.80 fpt nef tier 3 combine harvester service repair manualfusjejfkskemme
This document is a service manual for CNH Industrial combine harvesters including models TC4.90, TC5.70, TC5.80, TC5.90, and TC5.90 Hillside. The manual contains over 200 sections providing specifications, maintenance, and repair instructions for the combine's engine, transmission, axles, brakes, hydraulics, electrical systems, attachments, and all major operating systems. The sections are organized by functional area and component and include detailed diagrams, part numbers, and troubleshooting steps.
New holland mc28 commercial mower service repair manualfusjejfkskemme
This document is a service manual that provides technical information for servicing three commercial mower models: the MC22, MC28, and MC35. It contains sections covering various systems of the mowers like the engine, fuel system, rear axle, PTO, brakes, hydraulics, steering, electrical, and platform. The manual provides specifications, torque values, lubricant types, and safety and service information to properly maintain and repair the mowers.
New holland l234 tier 4 b (final) skid steer loader service repair manualfusjejfkskemme
This document provides instructions for removing the engine from a skid steer loader or compact track loader for service. It describes disconnecting various engine components like the battery, coolant, oil, and air conditioning system. It then outlines removing parts around the engine like panels, deck, and shroud to access the engine for removal. Safety warnings are provided to relieve pressures and support heavy components during the process.
New holland d180 c stage iiib crawler dozer service repair manual (pin nddc18...fusjejfkskemme
This document is a service manual for CNH Industrial's D180C Stage IIIB Crawler Dozer covering the following models: D180C Long Track, D180C Extra Long Track, and D180C Wide Track. The manual provides maintenance and repair instructions for the dozer's engine, hydraulic systems, tracks, cab climate control, electrical systems, dozer blade, tools, platform, and other components. It includes over 200 sections organized by subsystem with part numbers and replacement instructions.
New holland d180 c power angle tilt (pat) blade, low ground pressure (lgp) ...fusjejfkskemme
This document is a service manual for D180C crawler dozers that provides information on maintenance and repair of engine, hydrostatic drive, brakes, hydraulic systems, frames, tracks, cab climate control, electrical systems, dozer blade, tools, platform, and decals. It outlines safety procedures and contains sections covering various components and systems of the dozer.
New holland d180 c power angle tilt (pat) blade, long track (lt) tier 2 cra...fusjejfkskemme
This document is a service manual for D180C crawler dozers that provides information on maintenance and repair of engine, hydrostatic drive, brakes, hydraulic systems, frames, tracks, cab climate control, electrical systems, dozer blade, tools, platform, and decals. It outlines safety procedures and contains sections covering specific components.
New holland d150 c stage iiib crawler dozer service repair manual (pin nfdc15...fusjejfkskemme
This service manual provides information for servicing the following components of a D150C Crawler Dozer:
- Engine and related systems such as air cleaners, fuel filters, cooling and emissions systems
- Hydrostatic drive system
- Brakes and controls
- Hydraulic systems including cylinders, pumps and valves
- Tracks and track suspension
- Cab climate control and electrical systems
- Dozer blade and tools
- Cab, bodywork and decals
It provides removal and installation instructions, specifications and troubleshooting information for maintaining and repairing these components.
New holland d150 c bulldozer (bd) blade, extra long track (xlt) tier 2 craw...fusjejfkskemme
This document is a service manual for D150C Crawler Dozers that provides information on engine systems, hydrostatic drive, brakes and controls, hydraulic systems, tracks and suspension, cab climate control, electrical systems, dozer blade and arm, tools, and other components. It contains sections with detailed information and procedures for maintenance and repair of the various systems. Safety precautions are provided throughout for the protection of service personnel.
New holland cx5.90 laterale fpt nef 6 tier 4 b (final) combine harvester serv...fusjejfkskemme
This service manual provides technical information for maintenance and repair of CNH Industrial combine models CX5.80, CX5.90, CX5.90 Laterale, CX5.90 Hillside, CX6.80, CX6.90, and CX6.90 Laterale. The manual includes specifications, diagrams, and procedures for engine systems, transmission, axles, hydraulics, steering, climate control, electrical systems, attachments, feeding, threshing, separation, cleaning, and unloading systems. Sections cover all major mechanical, electrical, and hydraulic components of the combines.
New holland cr920 combine harvesters service repair manualfusjejfkskemme
This document is a repair manual for New Holland combine harvesters models CR920 through CR980. It contains sections covering all major systems of the combines from general information and safety to the engine, transmission, hydraulics, electrics, grain handling and more. The manual provides instructions for troubleshooting, overhaul, and testing procedures for technicians repairing and servicing the combines.
New holland c238 tier 4 b (final) compact track loader service repair manualfusjejfkskemme
This document provides a service manual for New Holland 200 Series Skid Steer Loaders and Compact Track Loaders with Tier 4B engines. It contains sections covering the engine, power coupling, front and rear axle systems, hydrostatic drive, brakes and controls, hydraulic systems, frames and ballasting, wheels, tracks and track suspension, cab climate control, electrical systems, front loader and bucket, platform, cab, bodywork, and decals. Safety information is also provided.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Dahua provides a comprehensive guide on how to install their security camera systems. Learn about the different types of cameras and system components, as well as the installation process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00448807
1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
Illustration 2 g00448808
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00448809
3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
Illustration 4 g00448810
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 5 g00475542
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00475546
4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:08:55 UTC+0800 2019
5/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Do not allow the tops of the fuel injector nozzles to turn while the fuel
lines are loosened. The fuel injector nozzles will be damaged if the tops
of the fuel injector nozzle turns in the body. Defective fuel injector
nozzles will damage the engine due to incorrect spray patterns.
Illustration 1 g00448820
1. Remove bolt (1) and the clamp that secures the fuel injector nozzle.
Illustration 2 g00448821
2. Install Tool (A) over the fuel injector nozzle. Turn screw (2) counterclockwise until the
button on the end of the screw is just above the bolt hole for the clamp that holds down the
fuel injector nozzle.
3. Tilt Tool (A) upward so that the inside lip of the fuel nozzle puller is under the diameter of
the fuel injector nozzle.
4. Turn screw (2) clockwise until the button on Tool (A) goes into the bolt hole for the clamp
that holds down the fuel injector nozzle.
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Do not exceed the recommended torque on the screw of the 6V-6980
Fuel Nozzle Puller in order to remove the nozzle. The nozzle will bend
or break if a torque greater than 17 N·m (13 lb ft) is applied.
5. Turn screw (2) clockwise in order to lift the fuel injector nozzle out of the bore. After the
fuel injector nozzle is loose in the bore of the cylinder head, move the fuel injector nozzle
upward and move the fuel injector nozzle downward. Moving the fuel injector nozzle helps
to loosen any carbon buildup and aids in the removal of the fuel injector nozzle.
6. When Tool (A) is used to remove the fuel injector nozzles, remove the carbon dam seal on
the end of the fuel injector nozzle.
Illustration 3 g00448822
7. If the fuel injector nozzle cannot be removed with Tool (A), Tool (B) must be used.
Note: When Tool (B) is used, it is likely that the fuel injector nozzle cannot be used again.
A new fuel injector nozzle will need to be installed as a replacement.
Note: Align the centerline of Tool (B) with the extended centerline of fuel injector nozzle
(3). This procedure will help prevent distortion of the fuel injector nozzle which can cause
the fuel injector nozzle to bend or break.
8. Remove the protective cap and install Tool (B) .
9. Use the slide hammer in order to remove fuel injector nozzle (3) .
10. Remove the compression seal from the fuel injector nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:09:51 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048591
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4979 Carbon Seal Installation Tool 1
B 8S-2245 Injector Cleaning Tool 1
C 6V-4089 Reamer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00448903
1. Put carbon dam seal (1) on the small end of Tool (A). Expand carbon dam seal (1) by
sliding carbon dam seal (1) to the large end of Tool (A). Put Tool (A) against the fuel
injector nozzle. Slide carbon dam seal (1) from Tool (A) to the fuel injector nozzle. Slide
carbon dam seal (1) into position in the groove of the fuel injector nozzle, as shown. Use
Tool (A) in order to install carbon dam seal (1).
2. To clean the fuel injector nozzles, refer to Special Instruction, SEHS7292 for the use of
Tool (B) .
3. Install a new compression seal (2) on the fuel injector nozzle.
Illustration 2 g00448904
4. Use Tool (C) in order to clean the bore in the cylinder head for the fuel injector nozzle. Use
a wrench in order to turn Tool (C) .
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00448905
Illustration 4 g00448906
5. Align notch (3) in fuel injector nozzle (5) to the tab in clamp (4) during installation.
6. Install fuel injector nozzle (5). Ensure that the notch in the injector is aligned with the tab in
clamp (4) .
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:10:47 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
Illustration 2 g00460631
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:11:43 UTC+0800 2019
2/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00460737
1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
Illustration 2 g00460791
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00460793
4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
Illustration 4 g00460795
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:12:38 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135000
Fuel Ratio Control - Assemble
SMCS - 1278-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the O-ring and the diaphragm. If the O-ring or the diaphragm is
worn or damaged use new parts for replacement.
1/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00460801
1. Install spring (1) and retainer (2) into housing (3) .
Illustration 2 g00460828
2. Install O-ring seal (6) and spring (5) into valve extension (7). Install stem (4) into valve
extension (7). Secure valve extension (7) to retainer (8) with nut (9) .
Illustration 3 g00460830
2/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 3. Install stem (4) and retainer (8) into housing (3) .
Illustration 4 g00460912
4. Install diaphragm (12), washer (11) and spring (10) on retainer (8) .
Illustration 5 g00460914
Illustration 6 g00460917
3/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 5. Install cover (13) on housing (3). Secure cover (13) with two bolts and washers.
6. Install O-ring seal (15) onto cover (14) and install cover (14) onto cover (13). Secure cover
(14) with two bolts.
Note: Refer to Testing and Adjusting, "Fuel System" for additional information on the
adjustment procedure for the fuel ratio control.
End By: Install the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:13:34 UTC+0800 2019
4/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00460631
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...