This document provides instructions for removing and disassembling the fuel ratio control component from a Caterpillar 3306 engine. It describes:
- Removing the fuel ratio control by disconnecting fuel lines and removing bolts.
- Disassembling the fuel ratio control by removing the cover and O-ring seal, which releases spring pressure. Tools including retaining ring pliers and a fixture assembly are required.
- Keeping all parts clean to prevent contamination.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
Learn why monitoring your Mercedes' Exhaust Back Pressure (EBP) sensor is crucial. Understand its role in engine performance and emission reduction. Discover five warning signs of EBP sensor failure, from loss of power to increased emissions. Take action promptly to avoid costly repairs and maintain your Mercedes' reliability and efficiency.
"Trans Failsafe Prog" on your BMW X5 indicates potential transmission issues requiring immediate action. This safety feature activates in response to abnormalities like low fluid levels, leaks, faulty sensors, electrical or mechanical failures, and overheating.
What Are The Immediate Steps To Take When The VW Temperature Light Starts Fla...Import Motorworks
Learn how to respond when the red temperature light flashes in your VW with this presentation. From checking coolant levels to seeking professional help, follow these steps promptly to prevent engine damage and ensure safety on the road.
What Does the PARKTRONIC Inoperative, See Owner's Manual Message Mean for You...Autohaus Service and Sales
Learn what "PARKTRONIC Inoperative, See Owner's Manual" means for your Mercedes-Benz. This message indicates a malfunction in the parking assistance system, potentially due to sensor issues or electrical faults. Prompt attention is crucial to ensure safety and functionality. Follow steps outlined for diagnosis and repair in the owner's manual.
𝘼𝙣𝙩𝙞𝙦𝙪𝙚 𝙋𝙡𝙖𝙨𝙩𝙞𝙘 𝙏𝙧𝙖𝙙𝙚𝙧𝙨 𝙞𝙨 𝙫𝙚𝙧𝙮 𝙛𝙖𝙢𝙤𝙪𝙨 𝙛𝙤𝙧 𝙢𝙖𝙣𝙪𝙛𝙖𝙘𝙩𝙪𝙧𝙞𝙣𝙜 𝙩𝙝𝙚𝙞𝙧 𝙥𝙧𝙤𝙙𝙪𝙘𝙩𝙨. 𝙒𝙚 𝙝𝙖𝙫𝙚 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙥𝙡𝙖𝙨𝙩𝙞𝙘 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙪𝙨𝙚𝙙 𝙞𝙣 𝙖𝙪𝙩𝙤𝙢𝙤𝙩𝙞𝙫𝙚 𝙖𝙣𝙙 𝙖𝙪𝙩𝙤 𝙥𝙖𝙧𝙩𝙨 𝙖𝙣𝙙 𝙖𝙡𝙡 𝙩𝙝𝙚 𝙛𝙖𝙢𝙤𝙪𝙨 𝙘𝙤𝙢𝙥𝙖𝙣𝙞𝙚𝙨 𝙗𝙪𝙮 𝙩𝙝𝙚 𝙜𝙧𝙖𝙣𝙪𝙡𝙚𝙨 𝙛𝙧𝙤𝙢 𝙪𝙨.
Over the 10 years, we have gained a strong foothold in the market due to our range's high quality, competitive prices, and time-lined delivery schedules.
Things to remember while upgrading the brakes of your carjennifermiller8137
Upgrading the brakes of your car? Keep these things in mind before doing so. Additionally, start using an OBD 2 GPS tracker so that you never miss a vehicle maintenance appointment. On top of this, a car GPS tracker will also let you master good driving habits that will let you increase the operational life of your car’s brakes.
What Could Cause The Headlights On Your Porsche 911 To Stop WorkingLancer Service
Discover why your Porsche 911 headlights might flicker out unexpectedly. From aging bulbs to electrical gremlins and moisture mishaps, we're delving into the reasons behind the blackout. Stay tuned to illuminate the road ahead and ensure your lights shine bright for safer journeys.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
In this presentation, we have discussed a very important feature of BMW X5 cars… the Comfort Access. Things that can significantly limit its functionality. And things that you can try to restore the functionality of such a convenient feature of your vehicle.
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00880175
Fuel Injection Lines - Remove and Install
SMCS - 1252-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00448807
1. Remove three bolts (1), (2) and (3) and the brackets from the fuel injection lines.
Illustration 2 g00448808
2. Disconnect six fuel injection line nuts (4) from the fuel injection pumps.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
2/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g00448809
3. Hold the tops of fuel injector nozzles (5) with a wrench, as shown. Loosen the six fuel
injection line nuts at fuel injector nozzles (4) .
4. Disconnect the fuel injection line nuts at the fuel injector nozzles and remove the fuel
injection lines. Put caps and plugs on all openings immediately in order to prevent dirt from
contaminating the fuel system.
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-0144 Fuel Line Socket 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Do not allow the tops of the nozzles to turn while the fuel lines are
loosened. The nozzles will be damaged if the top of the nozzle turns in
the body. Defective fuel nozzles will damage the engine due to incorrect
spray patterns.
3/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. 1. Remove the protective covers from the fuel line connections. Place the fuel injection lines in
position on the engine. Tighten the fuel injection line nuts on the fuel injection pump and
the fuel injector nozzles finger tight.
Note: The nozzle assembly must be supported with a wrench.
Illustration 4 g00448810
2. Hold the tops of fuel injector nozzles (1) and use Tool (A) in order to tighten the fuel
injection line nuts to a torque of 40 ± 7 N·m (30 ± 5 lb ft).
Illustration 5 g00475542
3. Tighten six fuel injection line nuts (2) at the fuel injection pumps to a torque of 40 ± 7 N·m
(30 ± 5 lb ft).
4/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00475546
4. Install the brackets and three bolts (3), (4) and (5) that hold the fuel injection lines in
position.
5. Prime the fuel system. Refer to the Operation and Maintenance Manual, "Fuel System -
Prime" topic (Maintenance Section).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:08:55 UTC+0800 2019
5/5235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048513
Fuel Injection Nozzles - Remove
SMCS - 1254-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-6980 Fuel Nozzle Puller 1
B
FT-1533 Adapter 1
1P-0074 Slide Hammer Puller 1
Start By:
A. Remove the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Do not allow the tops of the fuel injector nozzles to turn while the fuel
lines are loosened. The fuel injector nozzles will be damaged if the tops
of the fuel injector nozzle turns in the body. Defective fuel injector
nozzles will damage the engine due to incorrect spray patterns.
Illustration 1 g00448820
1. Remove bolt (1) and the clamp that secures the fuel injector nozzle.
Illustration 2 g00448821
2. Install Tool (A) over the fuel injector nozzle. Turn screw (2) counterclockwise until the
button on the end of the screw is just above the bolt hole for the clamp that holds down the
fuel injector nozzle.
3. Tilt Tool (A) upward so that the inside lip of the fuel nozzle puller is under the diameter of
the fuel injector nozzle.
4. Turn screw (2) clockwise until the button on Tool (A) goes into the bolt hole for the clamp
that holds down the fuel injector nozzle.
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. NOTICE
Do not exceed the recommended torque on the screw of the 6V-6980
Fuel Nozzle Puller in order to remove the nozzle. The nozzle will bend
or break if a torque greater than 17 N·m (13 lb ft) is applied.
5. Turn screw (2) clockwise in order to lift the fuel injector nozzle out of the bore. After the
fuel injector nozzle is loose in the bore of the cylinder head, move the fuel injector nozzle
upward and move the fuel injector nozzle downward. Moving the fuel injector nozzle helps
to loosen any carbon buildup and aids in the removal of the fuel injector nozzle.
6. When Tool (A) is used to remove the fuel injector nozzles, remove the carbon dam seal on
the end of the fuel injector nozzle.
Illustration 3 g00448822
7. If the fuel injector nozzle cannot be removed with Tool (A), Tool (B) must be used.
Note: When Tool (B) is used, it is likely that the fuel injector nozzle cannot be used again.
A new fuel injector nozzle will need to be installed as a replacement.
Note: Align the centerline of Tool (B) with the extended centerline of fuel injector nozzle
(3). This procedure will help prevent distortion of the fuel injector nozzle which can cause
the fuel injector nozzle to bend or break.
8. Remove the protective cap and install Tool (B) .
9. Use the slide hammer in order to remove fuel injector nozzle (3) .
10. Remove the compression seal from the fuel injector nozzle.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:09:51 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01048591
Fuel Injection Nozzles - Install
SMCS - 1254-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 6V-4979 Carbon Seal Installation Tool 1
B 8S-2245 Injector Cleaning Tool 1
C 6V-4089 Reamer 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g00448903
1. Put carbon dam seal (1) on the small end of Tool (A). Expand carbon dam seal (1) by
sliding carbon dam seal (1) to the large end of Tool (A). Put Tool (A) against the fuel
injector nozzle. Slide carbon dam seal (1) from Tool (A) to the fuel injector nozzle. Slide
carbon dam seal (1) into position in the groove of the fuel injector nozzle, as shown. Use
Tool (A) in order to install carbon dam seal (1).
2. To clean the fuel injector nozzles, refer to Special Instruction, SEHS7292 for the use of
Tool (B) .
3. Install a new compression seal (2) on the fuel injector nozzle.
Illustration 2 g00448904
4. Use Tool (C) in order to clean the bore in the cylinder head for the fuel injector nozzle. Use
a wrench in order to turn Tool (C) .
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 3 g00448905
Illustration 4 g00448906
5. Align notch (3) in fuel injector nozzle (5) to the tab in clamp (4) during installation.
6. Install fuel injector nozzle (5). Ensure that the notch in the injector is aligned with the tab in
clamp (4) .
End By: Install the fuel injection lines. Refer to Disassembly and Assembly, "Fuel Injection Lines
- Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:10:47 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903297
Fuel Ratio Control - Remove
SMCS - 1278-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00460630
1. Disconnect fuel pressure line (3). Remove two bolts (2) .
2. Move fuel ratio control (1) upward in order to disengage the fuel ratio control from the lever
assembly in the governor.
Illustration 2 g00460631
3. Remove four O-ring seals (4) and screen assembly (5) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:11:43 UTC+0800 2019
2/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903551
Fuel Ratio Control - Disassemble
SMCS - 1278-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
Start By:
A. Remove the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 1 g00460737
1. Remove cover (1) and O-ring seal (2) .
Personal injury can result from parts and/or covers under spring
pressure.
Spring force will be released when covers are removed.
Be prepared to hold spring loaded covers as the bolts are loosened.
2. In order to release the spring force, hold cover (3) in position and slowly remove the two
bolts that hold cover (3) in place.
Illustration 2 g00460791
3. Remove spring (4), washer (5) and diaphragm (6) from retainer (7). Remove retainer (7)
from housing (8) .
2/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 3 g00460793
4. Remove nut (13) from valve extension (12) and remove valve extension (12) from retainer
(7). Remove stem (9) from valve extension (12). Remove spring (10) and O-ring seal (11)
from valve extension (12) .
Illustration 4 g00460795
5. Remove spring (14) and retainer (15) from housing (8) .
6. All parts should be cleaned and inspected. Replace all parts that are worn or damaged.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:12:38 UTC+0800 2019
3/3235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01135000
Fuel Ratio Control - Assemble
SMCS - 1278-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A FT-1820 Fixture Assembly 1
B 1P-1855 Retaining Ring Pliers 1
C 6V-9072 Guide 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Check the condition of the O-ring and the diaphragm. If the O-ring or the diaphragm is
worn or damaged use new parts for replacement.
1/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 1 g00460801
1. Install spring (1) and retainer (2) into housing (3) .
Illustration 2 g00460828
2. Install O-ring seal (6) and spring (5) into valve extension (7). Install stem (4) into valve
extension (7). Secure valve extension (7) to retainer (8) with nut (9) .
Illustration 3 g00460830
2/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 3. Install stem (4) and retainer (8) into housing (3) .
Illustration 4 g00460912
4. Install diaphragm (12), washer (11) and spring (10) on retainer (8) .
Illustration 5 g00460914
Illustration 6 g00460917
3/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. 5. Install cover (13) on housing (3). Secure cover (13) with two bolts and washers.
6. Install O-ring seal (15) onto cover (14) and install cover (14) onto cover (13). Secure cover
(14) with two bolts.
Note: Refer to Testing and Adjusting, "Fuel System" for additional information on the
adjustment procedure for the fuel ratio control.
End By: Install the fuel ratio control. Refer to Disassembly and Assembly, "Fuel Ratio Control -
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Sep 27 15:13:34 UTC+0800 2019
4/4235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 235 EXCAVATOR 62X
Configuration: 235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00903481
Fuel Ratio Control - Install
SMCS - 1278-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 1 g00460631
1. Screen assembly (5) and four O-ring seals (4) should be inspected, replaced and installed.
1/2235 EXCAVATOR 62X00001-00288 (MACHINE) POWERED BY 3306 ENGINE(S...
2019/9/27https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...