The document provides instructions for removing a fuel injection pump from a Caterpillar 3304B or 3306B engine. It lists the required tools and gives warnings about containing fluids. The procedure involves removing bolts and a plate from the side of the fuel injection pump housing, inserting a timing pin, and using an extractor tool to remove the pump. Proper containment of fluids is emphasized.
This document provides assembly instructions for a governor in a Caterpillar 3306 engine used in an excavator model 235. It describes 38 assembly steps involving over 80 individual parts. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply proper preloads, and inserting seals with the correct orientation. Precision is required to ensure all parts are clean and positioned properly during reassembly.
This document provides assembly instructions for governors on Caterpillar 3304B and 3306B engines used in excavators. It details 27 steps to assemble parts like races, bearings, flyweights, carriers, dowels, springs, sleeves, pistons, valves, locks, bolts and seals. Special tools are required to install retaining rings, hold springs compressed, and set seals. Proper part cleaning, lubrication and alignment are emphasized to avoid contaminants and ensure correct assembly.
This document provides instructions for assembling the governor on a Caterpillar 3306 engine. It includes 39 steps detailing how to install various parts like races, bearings, flyweights, springs, sleeves, and housings. Tools required include retaining ring pliers, a spring clamp, and a driver group. Photos and diagrams accompany each step. The summary provides an overview of the governor assembly process without replicating the full content.
This document provides assembly instructions for governors on Caterpillar 3304B and 3306B engines used in excavators. It details 27 steps to assemble parts like races, bearings, flyweights, carriers, springs, sleeves, pistons, valves, levers, housings and seals. Tools include retaining ring pliers, spring clamps, driver groups and shield drivers. Clean oil is used to lubricate parts and ensure passages are clear.
This document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It involves 39 steps to assemble various governor components like carriers, flyweights, dashpots, pistons, sleeves, housings and seals. Special tools are required for some steps, and clean oil should be used to lubricate parts during assembly. Correct positioning of components like bolts, springs and collars is important for proper governor function.
The document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It describes 38 assembly steps requiring various tools. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply preload, and inserting seals in housings using special tools. Precision assembly is needed to ensure proper governor function for engine speed control.
The document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It describes 38 assembly steps requiring various tools. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply preload, and inserting seals in housings using special tools. Precision assembly is needed to ensure proper governor function for engine speed control.
This document provides instructions for removing a fuel injection pump from a Caterpillar 3304B or 3306B engine. It begins by listing the required tools. The removal procedure instructs the technician to first install a timing pin in the fuel injection pump housing to hold the fuel rack in the center position. Then a pump extractor tool is used to remove the fuel injection pump from the housing. Precautions are given to keep parts clean and contain fluids during the repair.
This document provides assembly instructions for a governor in a Caterpillar 3306 engine used in an excavator model 235. It describes 38 assembly steps involving over 80 individual parts. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply proper preloads, and inserting seals with the correct orientation. Precision is required to ensure all parts are clean and positioned properly during reassembly.
This document provides assembly instructions for governors on Caterpillar 3304B and 3306B engines used in excavators. It details 27 steps to assemble parts like races, bearings, flyweights, carriers, dowels, springs, sleeves, pistons, valves, locks, bolts and seals. Special tools are required to install retaining rings, hold springs compressed, and set seals. Proper part cleaning, lubrication and alignment are emphasized to avoid contaminants and ensure correct assembly.
This document provides instructions for assembling the governor on a Caterpillar 3306 engine. It includes 39 steps detailing how to install various parts like races, bearings, flyweights, springs, sleeves, and housings. Tools required include retaining ring pliers, a spring clamp, and a driver group. Photos and diagrams accompany each step. The summary provides an overview of the governor assembly process without replicating the full content.
This document provides assembly instructions for governors on Caterpillar 3304B and 3306B engines used in excavators. It details 27 steps to assemble parts like races, bearings, flyweights, carriers, springs, sleeves, pistons, valves, levers, housings and seals. Tools include retaining ring pliers, spring clamps, driver groups and shield drivers. Clean oil is used to lubricate parts and ensure passages are clear.
This document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It involves 39 steps to assemble various governor components like carriers, flyweights, dashpots, pistons, sleeves, housings and seals. Special tools are required for some steps, and clean oil should be used to lubricate parts during assembly. Correct positioning of components like bolts, springs and collars is important for proper governor function.
The document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It describes 38 assembly steps requiring various tools. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply preload, and inserting seals in housings using special tools. Precision assembly is needed to ensure proper governor function for engine speed control.
The document provides assembly instructions for a governor in a 3306 engine used in a 235 excavator model. It describes 38 assembly steps requiring various tools. Key steps include installing races and bearings on the camshaft, assembling flyweights and carriers, installing springs and sleeves to apply preload, and inserting seals in housings using special tools. Precision assembly is needed to ensure proper governor function for engine speed control.
This document provides instructions for removing a fuel injection pump from a Caterpillar 3304B or 3306B engine. It begins by listing the required tools. The removal procedure instructs the technician to first install a timing pin in the fuel injection pump housing to hold the fuel rack in the center position. Then a pump extractor tool is used to remove the fuel injection pump from the housing. Precautions are given to keep parts clean and contain fluids during the repair.
This document provides instructions for assembling the governor component of a Caterpillar 3306 engine. It includes 39 steps detailing how to install various parts like races, bearings, flyweights, springs, and housings. Tools required include retaining ring pliers, a spring clamp, and a driver group. Proper cleaning and lubrication of parts is emphasized. The assembly process involves installing individual components and subassemblies in the specified order and orientation.
This document provides assembly instructions for a hydraulic excavator pump in 61 steps. It lists the required tools and parts, and includes illustrations for each step. The pump assembly involves installing various components like housings, shafts, barrels, pistons, covers, seals, and controls in the correct order and orientation. Proper installation of orings and seals is important to prevent leaks.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in a specific order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, pistons, covers, and seals onto the pump housing in a specific order.
3. Tools and components like retaining rings, springs, and O-rings are also installed at various steps. Safety precautions are provided for installing components under spring pressure.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, seals, pistons, barrels, covers, and plates onto the pump housing in a specific order and orientation.
3. Tools and components like retaining rings, bolts, pins, springs, and covers are also installed onto the pump control and head assembly following illustrated diagrams.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, seals, pistons, barrels, covers, and more onto the pump housing in a specific order and orientation.
3. Tools and components are identified by name and numbering for each assembly step, with illustrations provided for clarification.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
This document provides assembly instructions for repairing a 329DL excavator. It outlines 60 steps to reassemble the main hydraulic pump, including installing various components like pistons, bearings, seals, and housings in the correct order and orientation. Tools and torque specifications are listed. Safety precautions are provided for steps involving compressed springs.
This document provides assembly instructions for a 329DL excavator service repair manual. It outlines 60 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, pistons, covers, and seals in the proper order and orientation. Tools and torque specifications are also listed. The assembly requires carefully following the illustrated instructions to ensure correct reassembly of the hydraulic pump system.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing components like gaskets, bearings, pistons, seals, covers, and controls into the pump housing and head. Tools and torque specifications are listed. Detailed illustrations accompany each step to show how to correctly position parts during reassembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
This document provides assembly instructions for a hydraulic excavator pump in 61 steps. It lists the required tools and parts, and includes illustrations for each step. The pump assembly involves installing various components like housings, shafts, barrels, pistons, covers, ports, and controls in the correct order and orientation. Proper seals, bearings, pins, and fasteners are also installed at each stage of assembly.
This document provides assembly instructions for repairing a 329DL excavator. It outlines 60 steps to reassemble the main hydraulic pump, including installing various components like pistons, bearings, seals, and housings in the correct order and orientation. Tools and safety precautions are also listed. The summary focuses on the overall goal and high-level process rather than detailed part numbers or illustrations.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, plates, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, plates, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
This document provides assembly instructions for a service repair manual in 52 steps. It details assembling various components of an excavator pump, including installing gaskets, bearings, pistons, housing covers, seals, and controls. Precautions are provided for working with pressurized springs. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
More Related Content
Similar to Caterpillar Cat 215C EXCAVATOR (Prefix 4HG) Service Repair Manual Instant Download.pdf
This document provides instructions for assembling the governor component of a Caterpillar 3306 engine. It includes 39 steps detailing how to install various parts like races, bearings, flyweights, springs, and housings. Tools required include retaining ring pliers, a spring clamp, and a driver group. Proper cleaning and lubrication of parts is emphasized. The assembly process involves installing individual components and subassemblies in the specified order and orientation.
This document provides assembly instructions for a hydraulic excavator pump in 61 steps. It lists the required tools and parts, and includes illustrations for each step. The pump assembly involves installing various components like housings, shafts, barrels, pistons, covers, seals, and controls in the correct order and orientation. Proper installation of orings and seals is important to prevent leaks.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in a specific order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, pistons, covers, and seals onto the pump housing in a specific order.
3. Tools and components like retaining rings, springs, and O-rings are also installed at various steps. Safety precautions are provided for installing components under spring pressure.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, seals, pistons, barrels, covers, and plates onto the pump housing in a specific order and orientation.
3. Tools and components like retaining rings, bolts, pins, springs, and covers are also installed onto the pump control and head assembly following illustrated diagrams.
1. This document provides assembly instructions for a 329DL excavator service repair manual, outlining 60 steps to assemble the main hydraulic pump.
2. The steps include installing various components like gaskets, bearings, seals, pistons, barrels, covers, and more onto the pump housing in a specific order and orientation.
3. Tools and components are identified by name and numbering for each assembly step, with illustrations provided for clarification.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing various components like gaskets, bearings, pistons, seals and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for clarity.
This document provides assembly instructions for repairing a 329DL excavator. It outlines 60 steps to reassemble the main hydraulic pump, including installing various components like pistons, bearings, seals, and housings in the correct order and orientation. Tools and torque specifications are listed. Safety precautions are provided for steps involving compressed springs.
This document provides assembly instructions for a 329DL excavator service repair manual. It outlines 60 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, pistons, covers, and seals in the proper order and orientation. Tools and torque specifications are also listed. The assembly requires carefully following the illustrated instructions to ensure correct reassembly of the hydraulic pump system.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble an excavator pump, including installing components like gaskets, bearings, pistons, seals, covers, and controls into the pump housing and head. Tools and torque specifications are listed. Detailed illustrations accompany each step to show how to correctly position parts during reassembly.
This document provides assembly instructions for a service repair manual in 3 sentences:
It outlines 53 steps to assemble a hydraulic pump, including installing various components like gaskets, bearings, pistons, seals, and covers onto the pump housing in the proper order and orientation. Precautions are noted for installing springs and other parts that could cause injury. Required tools are listed and each assembly step includes an illustration for reference.
This document provides assembly instructions for a hydraulic excavator pump in 61 steps. It lists the required tools and parts, and includes illustrations for each step. The pump assembly involves installing various components like housings, shafts, barrels, pistons, covers, ports, and controls in the correct order and orientation. Proper seals, bearings, pins, and fasteners are also installed at each stage of assembly.
This document provides assembly instructions for repairing a 329DL excavator. It outlines 60 steps to reassemble the main hydraulic pump, including installing various components like pistons, bearings, seals, and housings in the correct order and orientation. Tools and safety precautions are also listed. The summary focuses on the overall goal and high-level process rather than detailed part numbers or illustrations.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, plates, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, plates, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
This document provides assembly instructions for a service repair manual in 52 steps. It details assembling various components of an excavator pump, including installing gaskets, bearings, pistons, housing covers, seals, and controls. Precautions are provided for working with pressurized springs. Required tools include a transmission repair stand, link brackets, driver group, seal guide, and retaining ring pliers.
This document provides assembly instructions for a service repair manual for excavator models 329DL and 329D L. It lists 61 steps to assemble the main hydraulic pump, including installing various components like gaskets, bearings, seals, pistons, covers, and fittings in the correct order and orientation. Precautions are provided for steps involving spring tension. The final steps connect the assembled pump control and install the main hydraulic pump in the excavator.
Similar to Caterpillar Cat 215C EXCAVATOR (Prefix 4HG) Service Repair Manual Instant Download.pdf (20)
Caterpillar Cat 320D and 320D L Excavator (Prefix JFZ) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for removing and installing a flywheel housing on a 320D excavator. It describes removing bolts and washers to separate the housing from the cylinder block. It also includes removing the oil seal from the housing using a driver group tool. Reinstallation involves installing a new gasket and oil seal, then securing the housing with bolts and washers.
Caterpillar Cat 320D and 320D L Excavator (Prefix A8F) Service Repair Manual ...f8usejkdmmd8i
The document provides instructions for installing a crankshaft front seal on a Caterpillar C6.4 engine. It describes the required tools and safety precautions. The procedure involves cleaning the crankshaft, applying retaining compound, and pressing the new seal into place using a slide hammer puller. Care must be taken not to damage the crankshaft flange during installation.
This document provides instructions for removing and installing track carrier rollers, track rollers, and separating the track on a 320C Excavator. It describes:
1) Releasing tension on the track and loosening a relief valve before removing components.
2) Using tools like a hydraulic jack and lifting forks to support the track assembly and remove rollers and bolts.
3) Cleaning surfaces, positioning components, and reinstalling bolts and rollers in the reverse order of removal.
This document provides instructions for removing and installing the engine oil pump and water pump on a Caterpillar 320C excavator. The oil pump removal instructions involve removing bolts, gears, seals and other components. The installation involves cleaning parts, pressing components, heating items, and torquing bolts. The water pump instructions describe draining coolant and removing four bolts to take off the pump. Reassembly involves installing seals, bearings and an impeller on a shaft.
This document provides instructions for assembling and disassembling parts of a 320 GC Excavator model BR4, including the travel motor and final drive. It lists the required tools and parts and includes illustrations of the assembly and disassembly procedures. The travel motor assembly instructions involve installing positioning rods and lifting eyes to hold parts in place while bolts are tightened. The final drive disassembly involves removing the final drive housing from the excavator and using link brackets and forcing screws to separate connected components.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix DCK) Service Repair Ma...f8usejkdmmd8i
The document provides instructions for removing and installing track components on a 305.5 Mini Hydraulic Excavator, including:
- Removing and installing track rollers by raising the machine, removing bolts, and lowering it onto cribbing
- Separating the track by rotating it, removing shoes and bolts, and removing the master pin
- Reconnecting the track by installing the master pin and shoes with bolts
- Removing the front idler and track adjuster by sliding the track assembly away and lifting it off
- Installing the front idler and track adjuster by lifting it into place and sliding the track assembly over it
- Removing the recoil spring assembly
This document provides instructions for installing the fuel injection pump housing and governor on an excavator engine. It outlines 18 steps, including setting the number 1 piston to top center, installing timing pins, attaching the housing and governor, and connecting various lines and covers. Tools required include an engine turning tool, spanner wrench, and two fuel pump timing pins. Precise timing of the fuel injection pump camshaft is critical when attaching the housing.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix HC5) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various components of a 304E2 CR Mini Hydraulic Excavator engine, including the fuel manifold rail, fuel injection lines, exhaust gas recirculation cooler, fuel injection pump, and electronic unit injector. Safety precautions are outlined that must be followed when working on the fuel system, such as risks of high pressure fuel and containing any spilled fluids.
Caterpillar Cat 319D L and 319D LN Excavator (Prefix ZGZ) Service Repair Manu...f8usejkdmmd8i
The document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then outlines 28 steps for reassembling the final drive, including pressing in bearings, installing seals, and determining the correct shim thickness. The overall procedure involves separating, cleaning, and reassembling over 15 individual parts and components of the final drive.
Caterpillar Cat 319D L Excavator (Prefix KRM) Service Repair Manual Instant D...f8usejkdmmd8i
This document provides instructions for disassembling and assembling the final drive of a 319D L excavator. It describes 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It also describes 31 steps for reassembling these components, including pressing in bearings, determining shim thickness, and installing seals using a special tool. Proper cleaning, lubrication, and use of replacement parts is emphasized throughout.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix CJ2) Service Repair ...f8usejkdmmd8i
The document provides instructions for servicing components of a 304E2CR Mini Hydraulic Excavator engine. It describes procedures for removing and installing the crankshaft rear seal, flywheel housing, crankshaft pulley, and crankshaft front seal. The steps include using the proper tools, cleaning parts, applying sealant, and tightening to the specified torque values.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix KC4) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing various engine components on a 304E2CR Mini Hydraulic Excavator including the crankshaft rear seal carrier, flywheel housing, crankshaft pulley, crankshaft front seal, idler gear, front housing, and valve mechanism cover. The procedures include lists of required tools and step-by-step instructions with illustrations for each component. Precautions are provided regarding keeping parts clean and containing fluids.
Caterpillar Cat 304E2CR Mini Hydraulic Excavator (Prefix FC2) Service Repair ...f8usejkdmmd8i
The document provides instructions for removing and installing an engine oil cooler on a Caterpillar 304E2CR mini hydraulic excavator. The steps include draining coolant, removing hoses and clamps connecting the cooler, and removing mounting bolts. Reinstallation is the reverse of removal. Proper cleaning and torqueing of connections is emphasized.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TSR) Service Repair Man...f8usejkdmmd8i
This document provides instructions for removing and installing various track components on a 304E Mini Hydraulic Excavator, including the evaporator coil, track carrier roller, track roller, track, front idler, recoil spring, and hydraulic track adjuster. The procedures note required tools and safety precautions, and include illustrations and multiple step-by-step instructions for each component.
Caterpillar Cat 305.5 Mini Hydraulic Excavator (Prefix CXZ) Service Repair Ma...f8usejkdmmd8i
The document is a service repair manual that provides instructions for removing and installing components like the sprocket, final drive, and travel motor on a 305.5 Mini Hydraulic Excavator. It includes detailed removal and installation procedures with illustrations and lists required tools. Procedures include draining fluids, removing bolts and covers, disconnecting hoses, and lifting out heavy components. Disassembly steps describe removing gears, bearings, springs, and other internal parts.
Caterpillar Cat 304E Mini Hydraulic Excavator (Prefix TTN) Service Repair Man...f8usejkdmmd8i
The document provides instructions for servicing a 304E Mini Hydraulic Excavator. It describes procedures for removing and installing the sprocket and removing the final drive and travel motor. The final drive and travel motor are then disassembled by removing gears, bearings, seals, springs, and other internal components using the specified tools. Detailed illustrations accompany each step.
Caterpillar Cat 303.5E2CR Mini Hydraulic Excavator (Prefix CR6) Service Repai...f8usejkdmmd8i
This document provides instructions for installing and removing the governor and camshaft, and fuel injection pump on a 303.5E2CR Mini Hydraulic Excavator. It includes illustrations and step-by-step instructions for disassembling, cleaning, and reassembling these components. The instructions note to keep all parts clean and free of contaminants to prevent premature wear.
Caterpillar Cat 301.6C and 301.8C Mini Hydraulic Excavator (Prefix JSB) Servi...f8usejkdmmd8i
The document provides instructions for removing and disassembling various components of 301.6C and 301.8C mini hydraulic excavators, including the final drive and travel motor. The removal process involves draining fluids, disconnecting hoses, and removing bolts. Disassembly of the final drive and travel motor further requires removing retaining rings, springs, pins, seals and additional components using various specialized tools. Cleanliness is emphasized throughout to prevent contamination.
Caterpillar Cat 140M 3 MOTOR GRADER (Prefix N9M) Service Repair Manual Instan...f8usejkdmmd8i
1) The document provides instructions for disassembling the bank valve on the front and rear frames of a Caterpillar 140M 3 motor grader.
2) It describes removing 17 parts from the front bank valve including covers, seals, control valves, plugs, springs, balls, and fittings. Special precautions are listed for releasing spring forces.
3) Disassembling the rear bank valve involves removing 14 parts like covers, seals, control valves, plugs, springs, and tie rods. Again, warnings are given for spring-loaded components.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual Instan...f8usejkdmmd8i
This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides step-by-step instructions with accompanying illustrations. The transmission assembly involves installing bearings, gears, seals, pistons, clutches, and housing components in the specified order and with the correct torques. Proper cleaning, heating, lifting, and safety procedures are noted throughout the detailed assembly process.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Charging Fueling & Infrastructure (CFI) Program by Kevin MillerForth
Kevin Miller, Senior Advisor, Business Models of the Joint Office of Energy and Transportation gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Charging Fueling & Infrastructure (CFI) Program Resources by Cat PleinForth
Cat Plein, Development & Communications Director of Forth, gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Charging and Fueling Infrastructure Grant: Round 2 by Brandt HertensteinForth
Brandt Hertenstein, Program Manager of the Electrification Coalition gave this presentation at the Forth and Electrification Coalition CFI Grant Program - Overview and Technical Assistance webinar on June 12, 2024.
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01111261
Governor - Assemble
SMCS - 1264-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-1855 Retaining Ring Pliers 1
B 6V-2163 Spring Clamp 1
C 1P-0510 Driver Group 1
D 6V-2054 Shield Driver 1
Note: Put clean engine oil on all parts before assembly. Ensure that all of the oil passages are
clear.
Note: Check the condition of the gaskets and the O-ring seals. If the gaskets, the seals, or any
parts are worn or damaged, use new parts for replacement.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00453799
1. Install one race (1), bearing (2) and the other race (1) on the camshaft in the fuel injection
pump housing.
Illustration 2 g00453801
2. Put flyweights (4) in position on carrier (3) and install the dowels in order to hold the
flyweights in place. The flyweights must move freely on the dowels.
Illustration 3 g00453802
2/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. 3. Install dowel (5) in governor shaft (6) and install the governor shaft in the carrier (3) .
Illustration 4 g00459340
4. Put carrier (3) in position and install bolts (7) .
Illustration 5 g00459410
5. Install race (9), bearing (10) and race (9). Use Tool (A) in order to install ring (8) on riser
(11) .
3/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 6 g00459411
6. Install riser (11) .
Illustration 7 g00459414
7. Assemble the dashpot, as follows:
a. Install spring (13) on seat (12) and install seat (14) in spring (13) .
b. Put spool (15) and ring (16) in position on seat (14) and use Tool (A) in order to
install snap ring (17) .
4/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 8 g00459416
8. Install dashpot assembly (19). Install ring (18) in the lower groove in the governor shaft.
Illustration 9 g00459419
9. Install sleeve (20), spring (22), sleeve (20) and bearing (21) .
Note: Spring (22) is used in order to put a preload on the thrust bearing on the camshaft in
the fuel injection pump housing.
5/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 10 g00459421
10. Use Tool (B) in order to hold spring (22) compressed and install ring (23) in the groove in
the governor shaft. Remove Tool (B) .
Illustration 11 g00459423
11. Put lever (33) in position on the governor servo and install pin (32) in order to hold the lever
in place. Use a hammer and a chisel in order to move the metal (stake) at four places that are
spread apart 90 degrees. Perform this procedure on the outside surface on both legs of the
governor servo. This helps to hold pin (32) in place.
12. Install the O-ring seal on sleeve (25). Install piston (26) and sleeve (25) .
13. Install valve (24) .
14. Install one lockring (27) in the groove near the center of valve (24). Put sleeve (28), link
spring (29) and seat (30) in position on valve (24) and install second lockring (31) .
Illustration 12 g00454273
15. Put the governor servo in position on the fuel injection pump housing with piston (34) that
is engaged over rack control sleeve (35) and install the bolts that hold the rack control
sleeve in place.
6/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 13 g00591527
3304B engine
Note: The 3304B engine has one stop screw (36) and one locknut (38).
Illustration 14 g00454274
3306B
16. If the stop screws were removed, install two stop screws (36) in collar (37), as shown.
Install locknuts (38) .
7/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 15 g00454275
17. Install bolt (41) in block (42), as shown. Install spring (40) on bolt (41), as shown. Put collar
(37) in position on bolt (41) with the hole in the collar in alignment with the notch in bolt
(41) and install bolt (39) in order to hold the collar in place.
Illustration 16 g00454428
Illustration 17 g00459548
8/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. 18. Put block (42) in position on housing (43). Align the holes in block (42) with the dowels.
Tighten two bolts (44) .
Illustration 18 g00590080
3304B torque control
19. Assemble the torque control on the 3304B engine. Install retainer (51), two bars (49), spacer
(50), contact (46), and insulator (45) in position on bolts (52) .
9/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 19 g00454429
20. Assemble the torque control on the 3306B, as follows:
a. Install spring (48), spacer (47), contact (46) and spacer (50) on insulator (45), as
shown.
b. Install retainer (51) and bar (49) on bolts (52) .
10/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 20 g00459552
21. Put torque control (53) in position on block (40). Install bolts (54) .
Illustration 21 g00454442
Note: When housing (43) is installed on the fuel injection pump housing, the flange on bolt
(38) must be behind the dashpot. If housing (43) is installed with the flange on bolt (38) on
the wrong side of the dashpot, the riser in the governor will be held in the maximum fuel
delivery position.
22. Install gasket (56) on the fuel injection pump housing. Put housing (43) in position on the
fuel injection pump housing with bolt (38) behind the dashpot, as shown. Install bolts (55)
that hold housing (43) in place.
11/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 22 g00459558
23. Use Tool (C) in order to install lip type seal (57) in the outer governor housing with the lip
inward.
24. Install adjustment screw (58) and the locknut for the high idle adjustment.
Illustration 23 g00459560
25. Install check valve (59) .
12/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 24 g00459562
26. Put lever (60) in position, as shown. Install shaft (61) .
Illustration 25 g00459564
27. Put the gasket and shutoff solenoid (62) in position and install two bolts (63) .
28. Put the gasket and cover (64) in position and install two bolts (65) .
29. Install body (66) and contact (67) .
30. Put the O-ring seal on adapter (68) and put the coupling and adapter (68) in position. Install
two bolts (69) .
Illustration 26 g00459590
31. Install spring (70) in shaft assembly (71). Install pin (72) in shaft assembly (71). The tip of
pin (72) should be engaged in the hole in spring (70). Install pin (73) in shaft assembly (71)
in order to hold pin (72) in place.
13/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 27 g00459593
32. Put stop (76) and plates (74) in position on shaft assembly (71) and install pins (75). Install
snap rings (77) .
Illustration 28 g00459595
33. Put levers (79) and (78) in position in the housing, as shown. Install shaft assembly (71) .
Illustration 29 g00459596
14/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. 34. Install low idle adjustment screw (81) and the locknut. Install spring (80) in the hole in the
shaft assembly and in the housing.
Illustration 30 g00454486
35. Use Tool (C) in order to install lip type seal (82) in cover (83) with the lip, as shown. Install
the seal so that the seal is 2.0 ± 1.5 mm (.08 ± .06 inch) below the surface of the cover.
Illustration 31 g00459597
36. Put the gasket and cover (83) in position on the housing and install six bolts (84) .
15/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 32 g00459598
Note: Ensure that seat (85) and spring (86) are on top of lever (79). These parts must be
kept in this position when housing (87) is put in position on the inner governor housing.
37. Install seat (85) and spring (86) on the guide in the housing.
Illustration 33 g00459600
38. Put the gasket and housing (88) in position on the inner governor housing and install six
bolts (87) and two bolts (89) .
16/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 34 g00459667
39. Install fuel ratio control (90) onto governor (91) .
40. Make the governor adjustments. Refer to the Testing and Adjusting, "Fuel System" topic for
more information on governor adjustments.
End By: Install the fuel injection pump housing and the governor. Refer to the Disassembly and
Assembly, "Fuel Injection Pump Housing and Governor - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:29:47 UTC+0800 2020
17/17
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 EN...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00893695
Fuel Injection Pump - Remove
SMCS - 1251-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8T-5287 Wrench 1
B 6V-4186 Fuel Pump Timing Pin 1
C 8S-2244 Pump Extractor 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the machine. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide", for tools and supplies suitable to collect and contain
fluids in Caterpillar machines.
Dispose of all fluids according to local regulations and mandates.
1. Remove the bolts and the plate from the side of the fuel injection pump housing.
Illustration 1 g00455790
2. Install Tool (B) in the fuel injection pump housing. Move the fuel rack until Tool (B) can be
installed in order to hold the fuel rack in the center position for removing the fuel injection
pumps.
3. Use Tool (A) in order to remove bushing (1) .
4. Remove the O-ring seal from the fuel injection pump housing.
Illustration 2 g00455791
5. Install Tool (C) on the bonnet and remove the fuel injection pump.
2/3
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 3 g00455792
6. Remove spacer (2) .
Note: Keep spacers (2) and the fuel injection pump together and identify spacers (2) with
the location in the fuel injection pump housing.
7. Perform Steps 3 through 6 in order to remove the other fuel injection pumps.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:30:42 UTC+0800 2020
3/3
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00894023
Fuel Injection Pump - Disassemble
SMCS - 1251-015
Disassembly Procedure
Start By:
A. Remove the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
When the fuel injection pumps are disassembled, handle the parts
carefully. Do not damage the surfaces of the plungers, the barrels and
the bonnets. Any scratches will cause leakage inside the fuel injection
pump. The plunger and the barrel for each pump are made as a set. Do
not intermix the plunger of one pump in the barrel of another pump. If
one part is worn, install a completely new plunger and barrel assembly.
Be careful when placing the plunger into the bore of the barrel.
1/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Illustration 1 g00456318
1. Pull plunger (1) and washer (5) out of barrel (3) and spring (2) .
Note: Do not remove the gear from the plunger. The gear and the plunger are assembled
and adjusted at the factory.
2. Remove washer (5) and spring (2) .
3. Remove ring (6). Separate barrel (3) from bonnet (4) .
Illustration 2 g00456324
4. Remove check valve assembly (7) and spring (8). If check valve assembly (7) is
disassembled, do not mix parts with parts from another check valve assembly.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:31:38 UTC+0800 2020
2/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00894164
Fuel Injection Pump - Assemble
SMCS - 1251-016
Assembly Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Note: Put clean engine oil on all parts before assembly.
Illustration 1 g00456324
1. Install spring (8) and check valve assembly (7) in bonnet (4) .
1/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 2 g00456318
2. Install bonnet (4) on barrel (3) and install ring (6).
Note: Do not slide bonnet (4) across barrel (3). Check valve assembly (7) in the bonnet may
cause damage to the face of barrel (3) .
3. Install spring (2). Install washer (5) on plunger (1). Ensure that the flat side is facing toward
the gear on plunger (1) .
4. Install plunger (1) in barrel (3) until washer (5) is engaged in the spring.
End By: Install the fuel injection pumps. Refer to Disassembly and Assembly, "Fuel Injection
Pump - Install".
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:32:34 UTC+0800 2020
2/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i00894497
Fuel Injection Pump - Install
SMCS - 1251-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 8S-2244 Pump Extractor 1
B 6V-4186 Fuel Pump Timing Pin 1
C 8T-5287 Wrench 1
D
6V-9128 Rack Position Tool Group
1
3S-3270 Indicator Contact Point 1
C-clamp 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/4
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 1 g00507964
1. Install spacer (1) in the fuel injection pump housing.
Illustration 2 g00507989
Illustration 3 g00508002
2. Install Tool (B) in the fuel injection pump housing. Move the rack until Tool (B) can be
installed in order to hold the rack in the center position. The rack must be in the center
position in order to install the fuel injection pumps.
2/4
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. 3. Turn the camshaft until the lobe of the camshaft is downward so that the fuel injection pump
can be installed.
4. Install Tool (A) on the bonnet of the fuel injection pump.
5. Install the fuel injection pump in the fuel injection pump housing. Ensure that slot (3) that is
cut in the gear is aligned with the small pin (2) and groove (4) in the barrel. The small pin
(2) and groove (4) in the barrel are aligned with dowel (5) in the fuel injection pump
housing.
Illustration 4 g00508005
6. Put clean engine oil on O-ring seal (6) and install the O-ring seal in the fuel injection pump
housing.
Illustration 5 g00508057
7. Install bushing (7) by hand until the bushing is even with the top of the fuel injection pump
housing. If bushing (7) cannot be installed by hand, remove bushing (7). Remove the fuel
injection pump. Put the pump in alignment and reinstall bushing (7) .
8. Install Tool (C) on bushing (7) and tighten the bushing to a torque of 163 ± 14 N·m (120 ±
10 lb ft).
3/4
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. 9. Install Tool (D) in order to measure the total travel of the rack. The correct travel for the
rack is 15.70 mm (.618 inch). A smaller measurement is an indication of improper fuel
injection pump installation.
10. Repeat Steps 1 through 9 in order to install the remaining fuel injection pumps.
11. Install the cover and the gasket on the fuel injection pump housing.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:33:30 UTC+0800 2020
4/4
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01117604
Turbocharger - Remove
SMCS - 1052-011
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
32. Illustration 1 g00537468
1. Remove bolt (2) and the clamp that holds the oil supply tube and the oil drain tube in
position.
2. Remove two bolts (1) that hold the oil supply tube to the turbocharger. Remove two bolts
(3) that hold the oil drain tube to the turbocharger.
3. On the 3304B, loosen the two hose clamps and remove the hose from the turbocharger.
Slide the hose onto the pipe that goes to the cylinder head.
4. Loosen nut (4) and remove the oil supply tube from the engine.
Illustration 2 g00537495
5. Loosen four bolts (6) and the nuts that hold turbocharger (5) to the exhaust manifold.
Remove turbocharger (5) and the gasket from the exhaust manifold. Remove oil drain tube
(7) from the engine and check the O-ring seal for damage. If the O-ring seal is worn or
damaged, use a new part for replacement.
Copyright 1993 - 2020 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Dec 19 15:34:25 UTC+0800 2020
2/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 215C EXCAVATOR 4HG
Configuration: 215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGINE
Disassembly and Assembly
3304B and 3306B Engines for Caterpillar Built Machines
Media Number -SENR5598-09 Publication Date -01/01/2013 Date Updated -25/01/2013
i01009195
Turbocharger - Disassemble
SMCS - 1052-015
Disassembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 9S-6363 Turbocharger Fixture Group 1
Start By:
A. Remove the turbocharger. Refer to Disassembly and Assembly, "Turbocharger - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/2
215C & 219 EXCAVATOR 4HG00001-UP (MACHINE) POWERED BY 3304 ENGI...
2020/12/19
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...