This document provides assembly instructions for a transmission in a 12H motor grader. It lists over 50 steps to assemble components like bearings, gears, clutches, pistons, seals and shafts. Detailed illustrations accompany each step. Tools required are also listed. Proper heating and installation of bearings is emphasized. Multiple people may be needed to manually position heavy components.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...udjkdksmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual Instant ...udjkskdmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 42 steps to assemble various transmission components including gears, shafts, bearings, seals and clutches. Tools required include lifting fixtures, pullers, bolts and nuts. Components are installed in stages on input, forward and reverse/second shafts and include checking bearings are seated and seals are installed correctly with lips facing inward.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...ufjskekdjdmw2
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 42 steps to assemble various transmission components including gears, shafts, bearings, seals and clutches. Tools required include lifting fixtures, pullers, bolts and nuts. Components are installed in stages on input, forward and reverse/second shafts and include checking bearings are seated and seals are installed correctly with lips facing inward.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...ufuejkdkmdm
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual Instant ...yan77xunhao
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required include pullers, bolts, nuts, and heating equipment. Proper assembly requires positioning components in their original locations and applying the correct torque to fasteners.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...vvnj41316031
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...jdkksmemmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, seals, gears, shafts, and other components into the transmission case and cover. The assembly involves installing multiple clutches, bearings, seals and gears onto several shafts before positioning the shafts into the transmission casing. Proper alignment and torque of fasteners is important for correct assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...gen78guozun
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required include pullers, bolts, nuts, and heating equipment. Proper assembly requires positioning components, applying sealant, and heating bearings to specific temperatures before installation.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...udjkdksmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual Instant ...udjkskdmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 42 steps to assemble various transmission components including gears, shafts, bearings, seals and clutches. Tools required include lifting fixtures, pullers, bolts and nuts. Components are installed in stages on input, forward and reverse/second shafts and include checking bearings are seated and seals are installed correctly with lips facing inward.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...ufjskekdjdmw2
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 42 steps to assemble various transmission components including gears, shafts, bearings, seals and clutches. Tools required include lifting fixtures, pullers, bolts and nuts. Components are installed in stages on input, forward and reverse/second shafts and include checking bearings are seated and seals are installed correctly with lips facing inward.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...ufuejkdkmdm
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual Instant ...yan77xunhao
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required include pullers, bolts, nuts, and heating equipment. Proper assembly requires positioning components in their original locations and applying the correct torque to fasteners.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...vvnj41316031
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...jdkksmemmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, seals, gears, shafts, and other components into the transmission case and cover. The assembly involves installing multiple clutches, bearings, seals and gears onto several shafts before positioning the shafts into the transmission casing. Proper alignment and torque of fasteners is important for correct assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...gen78guozun
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required include pullers, bolts, nuts, and heating equipment. Proper assembly requires positioning components, applying sealant, and heating bearings to specific temperatures before installation.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...soeldksejdksem
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...f7usedkddmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 40 steps to assemble various transmission components like gears, shafts, bearings, seals and clutches. These include heating bearings, installing retainers, seals, plates, discs, springs, pistons and more. Tools required are also listed. The transmission is assembled by positioning various components in the transmission case and cover in the specified order and orientation.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fusjejedrfjskekem
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing components like bearings, gears, shafts, and clutches into the transmission case and cover. The transmission involves assembling multiple gear and clutch assemblies onto several shafts before installing the shafts into the transmission casing.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...dujjsjekkkdmm
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, gears, shafts, clutches, and seals into the transmission case and cover assembly. The multi-page instructions describe heating and pressing components, aligning splines, and using lifting fixtures to position heavy assemblies during the rebuild process.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjskekdmem
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing various transmission components including bearings, gears, shafts, seals, and clutches. The assembly involves heating and pressing components, installing seals and lubricants, and positioning heavy assemblies with lifting tools.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjsefkkertsemme
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 53 steps to assemble components like bearings, gears, clutches, seals and shafts. Tools required include pullers, bolts, nuts and heating equipment. Proper order and alignment of splines is important. Weights of assembled components are provided to assist installation.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjsekdmme
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, gears, shafts, clutches, and seals into the transmission case and cover assembly. The multi-page instructions describe heating and pressing components, installing snap rings and seals, and positioning heavy shaft assemblies with lifting tools.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It outlines 42 steps to assemble the input shaft, carrier assemblies, ring gears, planetary gears, output shaft, and other components. Tools and parts required are listed. Detailed illustrations accompany each step to show proper positioning and orientation of parts. Cleanliness and use of transmission oil during assembly are emphasized.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 57 assembly steps to install various transmission components such as bearings, gears, shafts, seals, and housings. Cleanliness is important during assembly and transmission oil should be applied to internal parts. Required tools include various driver groups, retaining ring pliers, and link brackets.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 57 assembly steps to install various transmission components such as bearings, gears, shafts, seals, and housings. Cleanliness is important during assembly and all parts must be thoroughly cleaned before installation. Lubrication with transmission oil is also required for internal parts. Proper tooling is listed for expanding retaining rings and installing components.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
1) The document provides disassembly and assembly instructions for the final drive of a 318C excavator.
2) It lists required tools and parts and gives step-by-step instructions to disassemble components like the cover, planetary assembly, ring gear, and carrier.
3) The assembly section instructs to clean all parts thoroughly and replace all seals before reinstalling components like the support ring, planetary gears, and retainer nut in the reverse order of disassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix MDY) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and housing. It then lists 7 notes and 28 steps to reassemble the final drive by installing components like seals, bearings, shims, and housing pieces in the reverse order of disassembly. The goal is to carefully disassemble and reassemble the final drive while cleaning parts and applying sealant or anti-seize compound where needed.
Caterpillar Cat 318D L Excavator (Prefix ZKJ) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists notes on cleanliness and provides 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
More Related Content
Similar to Caterpillar Cat 12H NA Motor Grader (Prefix 4XM) Service Repair Manual Instant Download.pdf
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...soeldksejdksem
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 50 steps to assemble various transmission components including bearings, gears, shafts, seals, and clutches. Tools required are also listed. The transmission components are assembled onto several shafts, which are then installed into the transmission case and cover. Proper alignment of splines and sealing of components is important during assembly.
Caterpillar Cat 120K Motor Grader (Prefix JAP) Service Repair Manual (JAP0000...f7usedkddmmd
This document provides assembly instructions for a transmission in a 120K motor grader. It lists over 40 steps to assemble various transmission components like gears, shafts, bearings, seals and clutches. These include heating bearings, installing retainers, seals, plates, discs, springs, pistons and more. Tools required are also listed. The transmission is assembled by positioning various components in the transmission case and cover in the specified order and orientation.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fusjejedrfjskekem
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing components like bearings, gears, shafts, and clutches into the transmission case and cover. The transmission involves assembling multiple gear and clutch assemblies onto several shafts before installing the shafts into the transmission casing.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...dujjsjekkkdmm
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, gears, shafts, clutches, and seals into the transmission case and cover assembly. The multi-page instructions describe heating and pressing components, aligning splines, and using lifting fixtures to position heavy assemblies during the rebuild process.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjskekdmem
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing various transmission components including bearings, gears, shafts, seals, and clutches. The assembly involves heating and pressing components, installing seals and lubricants, and positioning heavy assemblies with lifting tools.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjsefkkertsemme
This document provides assembly instructions for a transmission in a 120K motor grader. It outlines 53 steps to assemble components like bearings, gears, clutches, seals and shafts. Tools required include pullers, bolts, nuts and heating equipment. Proper order and alignment of splines is important. Weights of assembled components are provided to assist installation.
Caterpillar cat 120 k motor grader (prefix jap) service repair manual (jap000...fjjsekdmme
This document provides assembly instructions for a transmission in a 120K Motor Grader. It lists the required tools and parts and provides detailed steps and illustrations for installing bearings, gears, shafts, clutches, and seals into the transmission case and cover assembly. The multi-page instructions describe heating and pressing components, installing snap rings and seals, and positioning heavy shaft assemblies with lifting tools.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It outlines 42 steps to assemble the input shaft, carrier assemblies, ring gears, planetary gears, output shaft, and other components. Tools and parts required are listed. Detailed illustrations accompany each step to show proper positioning and orientation of parts. Cleanliness and use of transmission oil during assembly are emphasized.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 57 assembly steps to install various transmission components such as bearings, gears, shafts, seals, and housings. Cleanliness is important during assembly and transmission oil should be applied to internal parts. Required tools include various driver groups, retaining ring pliers, and link brackets.
This document provides assembly instructions for the transmission planetary system of a 950H wheel loader. It describes 57 assembly steps to install various transmission components such as bearings, gears, shafts, seals, and housings. Cleanliness is important during assembly and all parts must be thoroughly cleaned before installation. Lubrication with transmission oil is also required for internal parts. Proper tooling is listed for expanding retaining rings and installing components.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. Detailed steps include installing bearings, seals, gears, discs, plates, pistons, housings and other components. Proper cleaning, lubrication, and use of installation tools are emphasized.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a planetary transmission used in a 972H wheel loader. It describes how to assemble the input shaft, carrier assemblies, clutch components, output shaft, and other parts. Detailed steps and illustrations are provided to guide technicians through the assembly process. Cleanliness is emphasized and special tools are required to properly install some components like bearings. The assembly involves over 40 individual steps and requires lifting heavy parts into place.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections that describe assembling the planetary gear sets and clutches for the input, intermediate, and output sections of the transmission. The instructions include installing bearings, gears, shafts, seals, and other components in the specified order. Tools and torque specifications are listed. Cleanliness is emphasized during assembly to prevent lint or other contaminants.
This document provides assembly instructions for a 972H wheel loader transmission. It consists of 3 sections detailing the assembly of the transmission's planetary gear sets and clutches. The summary includes:
1) Cleaning and preparing transmission components before assembly.
2) Assembling the three planetary gear sets which include installing bearings, gears, shafts, seals and retaining rings.
3) Installing clutches which involve alternating friction discs and plates, installing seals, pistons and springs.
Similar to Caterpillar Cat 12H NA Motor Grader (Prefix 4XM) Service Repair Manual Instant Download.pdf (16)
1) The document provides disassembly and assembly instructions for the final drive of a 318C excavator.
2) It lists required tools and parts and gives step-by-step instructions to disassemble components like the cover, planetary assembly, ring gear, and carrier.
3) The assembly section instructs to clean all parts thoroughly and replace all seals before reinstalling components like the support ring, planetary gears, and retainer nut in the reverse order of disassembly.
Caterpillar Cat 318D2 and 318D2 L Excavator (Prefix SGB) Service Repair Manua...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D2 excavator. It lists the required tools and outlines 33 steps to disassemble the final drive components such as the cover, carrier assembly, ring gears, and housing. It then describes 28 steps to reassemble the final drive, including preloading the bearings, installing seals and pins, and reassembling the carrier assembly components. Cleanliness is emphasized throughout to prevent dirt from entering internal mechanisms during disassembly and assembly.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix MDY) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps to disassemble the final drive by removing components like the cover, carrier assembly, ring gears, and housing. It then lists 7 notes and 28 steps to reassemble the final drive by installing components like seals, bearings, shims, and housing pieces in the reverse order of disassembly. The goal is to carefully disassemble and reassemble the final drive while cleaning parts and applying sealant or anti-seize compound where needed.
Caterpillar Cat 318D L Excavator (Prefix ZKJ) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318D L excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive cover, carrier assembly, ring gears, and other components. It then lists 13 steps for assembly, including installing bearings in the main housing, preloading the bearings to determine the correct shim thickness, installing seals and gears, and reassembling disassembled components. The goal is to disassemble and clean all parts before precise reassembly in the reverse order of disassembly.
Caterpillar Cat 318D2 L Excavator (Prefix DPJ) Service Repair Manual Instant ...ze6074xunong
This document provides instructions to disassemble the final drive of a 318D2 L excavator. It lists the required tools and presents 33 steps to fully disassemble the final drive and its components. Key steps include removing the final drive assembly and mounting it to a repair stand, removing plugs and springs from the assembly while taking safety precautions for released spring forces, and using lifting devices to remove heavier internal components like the carrier assembly. The goal is to fully separate all individual parts for inspection or replacement.
Caterpillar Cat 318C, 318C L and 318C LN Excavator (Prefix GPA) Service Repai...ze6074xunong
This document provides instructions for disassembling and assembling the final drive of a 318C excavator. It lists the required tools and presents 33 steps for disassembly, including removing the final drive sprocket, carrier assembly, ring gears, and other components. It then lists notes on cleanliness and provides 14 steps for reassembling the final drive, including installing bearings, shims, and seals. The purpose is to provide maintenance technicians with a procedure for taking apart and rebuilding the excavator's final drive system.
This document provides instructions for removing and installing various engine components on a 299D XHP Compact Track Loader, including the diesel particulate filter, air inlet heater, inlet manifold, and inlet and exhaust valves. The procedures describe disconnecting wiring harnesses, removing mounting bolts, and installing replacement parts in the reverse order of removal, taking safety precautions for hot components. Tools required include goggles, gloves, a respirator, and specialty tools for compressing valve springs.
Caterpillar Cat 257D MULTI TERRAIN LOADER (Prefix EZW) Service Repair Manual ...ze6074xunong
The document provides instructions for removing and installing a piston pump on a 257D Multi Terrain Loader. It lists required tools and outlines a step-by-step process including disconnecting hoses and harnesses, using lifting tools to support the pump, and removing bolts. The reassembly process is described in reverse order, noting steps like applying thread lock compound and centering the swashplate.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix R9M) Service Repair Manual Instan...ze6074xunong
This document provides instructions for removing and installing the engine on a Caterpillar 140M 2 motor grader. Key steps include draining fluids, disconnecting tubes, hoses and wiring harnesses, and removing mounting bolts. Special tools may be required to remove some components. The engine should be attached to a lifting device and removed, then the installation process follows the removal steps in reverse order. Safety precautions are provided regarding contained fluids, pressurized systems, and ensuring parts are kept clean to prevent damage.
The document provides instructions for removing and installing an idler gear on a Caterpillar 299D2 XHP compact track loader. The removal procedure involves removing the front housing, ensuring the piston is at top center position, marking gear alignment, installing a flywheel stopper tool, and removing bolts, plates and the idler gear. The installation procedure specifies cleaning and applying oil to parts, ensuring correct bushing alignment, and tightening bolts to the specified torque.
Caterpillar Cat 257B3 MULTI TERRAIN LOADER (Prefix B7H) Service Repair Manual...ze6074xunong
This document provides disassembly and assembly instructions for a piston motor (hydrostatic) on a Caterpillar 257B3 Multi Terrain Loader. It lists 42 steps to disassemble the piston motor by removing various components like springs, seals, pins, gears, and bearings. It then lists 13 steps to assemble the piston motor by installing those same components in reverse order. The document includes illustrations and lists required tools for each step.
Caterpillar Cat 257 Multi Terrain Loader (Prefix CMM) Service Repair Manual I...ze6074xunong
This document provides instructions for removing and installing a flywheel housing on a 257 Multi Terrain Loader with a 3034 engine. It describes using link brackets and a lifting device to remove the flywheel housing by removing its bolts. For installation, it instructs cleaning the cylinder block face, placing the housing over dowels on the block, and reinstalling the bolts while using link brackets for support. Precautions are given to keep parts clean and not damage surfaces.
Caterpillar Cat 143H Motor Grader (Prefix APN) Service Repair Manual Instant ...ze6074xunong
The document provides instructions for disassembling and assembling the final drive of a 143H motor grader. It describes removing the final drive unit and then disassembling it by removing gears, shafts, bearings and seals. The assembly section describes installing these components in reverse order and adjusting shims to set proper end play. Precautions are given to clean parts thoroughly and use new parts if worn.
Caterpillar Cat 140M 3 AWD MOTOR GRADER (Prefix N9J) Service Repair Manual In...ze6074xunong
This document provides instructions for disassembling and assembling the piston pump of a Caterpillar 140M 3 AWD motor grader. The disassembly procedure involves removing 18 components of the pump including valves, seals, springs, spools, pistons, and plates. The assembly procedure outlines installing these components in reverse order and notes to keep parts clean and check seals for wear.
Caterpillar Cat 140M Motor Grader (Prefix B9M) Service Repair Manual Instant ...ze6074xunong
This document provides instructions for removing the drawbar from a 140M Motor Grader. It lists the required tools, gives safety warnings about hydraulic pressure, and outlines a 26-step procedure involving lowering the blade, removing bolts and pins, and using lifting equipment to remove the drawbar. Proper identification and plugging of hoses is noted to prevent fluid loss and contamination during the process.
The document provides instructions for removing and installing various engine components on a 299D XHP Compact Track Loader, including the water pump, water temperature regulator, flywheel, and crankshaft rear seal. The procedures describe draining coolant, removing guards and belts, and installing replacement parts in the reverse order of removal while taking safety precautions. Tools required include Three Bond 1217H adhesive and guide bolts for installing the flywheel.
Caterpillar Cat 140M 2 MOTOR GRADER (Prefix M9D) Service Repair Manual Instan...ze6074xunong
This document provides assembly instructions for a transmission in a 140M 2 motor grader. It lists required tools and parts and provides 44 steps and illustrations to assemble the transmission components which include installing bearings, gears, seals, pistons, clutches, and housing components. Proper cleaning, heating/cooling of parts, and torque specifications are noted throughout the assembly process.
Caterpillar Cat 315B L Excavator (Prefix 5SW) Service Repair Manual Instant D...ze6074xunong
This document provides instructions for disassembling and assembling the travel motor of a 315B L excavator. The disassembly process involves removing 23 separate components from the travel motor in a specific sequence. The assembly process reverses the disassembly steps and provides additional details to ensure proper reinstallation of components, such as applying sealant and lubricant, and using strings to hold parts in place temporarily.
The document provides instructions for removing and installing various engine components on a Caterpillar C3.8 engine, including:
- Installing the flywheel, ensuring the ring gear is oriented correctly
- Removing and installing the crankshaft rear seal and carrier
- Removing and installing the flywheel housing
- Removing and installing the crankshaft pulley
The procedures include lists of required tools and step-by-step instructions with accompanying illustrations. Safety and installation notes are provided throughout.
This document provides instructions for disassembling and assembling the travel motor on a 315C Excavator. The disassembly process involves removing 27 individual parts in 28 steps, including removing bolts, seals, bearings, pistons, and other internal components. The assembly process reverses the disassembly steps and includes applying lubricant to parts and ensuring proper installation of springs, seals, and other components. Cleanliness is emphasized throughout to prevent contamination.
Understanding Catalytic Converter Theft:
What is a Catalytic Converter?: Learn about the function of catalytic converters in vehicles and why they are targeted by thieves.
Why are They Stolen?: Discover the valuable metals inside catalytic converters (such as platinum, palladium, and rhodium) that make them attractive to criminals.
Steps to Prevent Catalytic Converter Theft:
Parking Strategies: Tips on where and how to park your vehicle to reduce the risk of theft, such as parking in well-lit areas or secure garages.
Protective Devices: Overview of various anti-theft devices available, including catalytic converter locks, shields, and alarms.
Etching and Marking: The benefits of etching your vehicle’s VIN on the catalytic converter or using a catalytic converter marking kit to make it traceable and less appealing to thieves.
Surveillance and Monitoring: Recommendations for using security cameras and motion-sensor lights to deter thieves.
Statistics and Insights:
Theft Rates by Borough: Analysis of data to determine which borough in NYC experiences the highest rate of catalytic converter thefts.
Recent Trends: Current trends and patterns in catalytic converter thefts to help you stay aware of emerging hotspots and tactics used by thieves.
Benefits of This Presentation:
Awareness: Increase your awareness about catalytic converter theft and its impact on vehicle owners.
Practical Tips: Gain actionable insights and tips to effectively prevent catalytic converter theft.
Local Insights: Understand the specific risks in different NYC boroughs, helping you take targeted preventive measures.
This presentation aims to equip you with the knowledge and tools needed to protect your vehicle from catalytic converter theft, ensuring you are prepared and proactive in safeguarding your property.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Expanding Access to Affordable At-Home EV Charging by Vanessa WarheitForth
Vanessa Warheit, Co-Founder of EV Charging for All, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
EV Charging at MFH Properties by Whitaker JamiesonForth
Whitaker Jamieson, Senior Specialist at Forth, gave this presentation at the Forth Addressing The Challenges of Charging at Multi-Family Housing webinar on June 11, 2024.
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: MOTOR GRADER
Model: 12H NA MOTOR GRADER 4XM
Configuration: 12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine
Disassembly and Assembly
12H, 140H and 160H Motor Graders Power Train
Media Number -SENR8548-14 Publication Date -01/10/2011 Date Updated -12/10/2011
i05303122
Transmission - Assemble
SMCS - 3030-016
Assembly Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 5P-9736 Link Bracket 1
B 154-6181 Forcing Screw 2
C 6V-5221 Bolt 1
D 4C-8156 Lifting Fixture 1
E 6V-3918 Bolt 1
F 4C-8157 Lifting Fixture 2
G 1U-6405 Three Jaw Puller 1
H 1U-6341 Threaded Rod 1
J 5P-7970 Nut 1
K 9U-7479 Compressing Tube 1
L 5B-0637 High Idle Nut 1
5F-7353 Washer 1
1B-4207 Full Nut 2
5F-7369 Puller Leg 2
3H-0465 Push-Puller Plate 2
1/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. 5F-7366 Forcing Screw 1
5P-4808 Cap 2
1U-9895 Crossblock 1
M
9S-9151 Block 2
1B-4206 Nut 4
8B-7552 Forcing Bolt 2
N 1U-6343 Threaded Rod 1
P 6V-8149 Nut 1
Q 2P-8312 Retaining Ring Pliers 1
R
1P-2326 Forcing Screw 1
1P-2325 Head 1
3H-0462 Bolt 4
8H-0709 Strap 4
5F-7373 Jaw 3
S 3E-3882 Eyebolt 1
T 6V-5765 Sealant 1
Note: Remove old anaerobic sealant from the bottom of the blind tapped holes in housing (11)
before assembling.
Illustration 1 g00623302
1. Lower the temperature of bearing outer races (130) . Install bearing outer races (130) to the
original locations in both transmission case assembly (3) (not shown) and the transmission
cover assembly (11) until bearing outer races (130) are seated.
2/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00623301
2. Install bearing retainer (128) on gear assembly (126) .
3. Heat ball bearing (127) to a maximum of 135 °C (275 °F). Install ball bearing (127) to the
original location on gear assembly (126) .
4. Use Tooling (Q) in order to install snap ring (129) to the original location on gear assembly
(126) .
Illustration 3 g00623300
5. Install gear assembly (126) to the original location in the transmission cover assembly (11) .
6. Install two bolts (not shown) on the gear assembly (126) .
7. Install four bolts (125) in the gear assembly (126) . Tighten bolts (125) to a torque of 28 ± 7
N·m (21 ± 5 lb ft).
3/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Illustration 4 g00623299
8. Install the cup plug (not shown) in input shaft assembly (65) .
9. Install gear (124) on Input shaft assembly (65) .
10. Heat inner bearing (123) to a maximum of 135 °C (275 °F). Install inner bearing (123) on
Input shaft assembly (65) until inner bearing (123) is seated. Gear (124) should be tight on
input shaft assembly (65) .
11. Install two seal rings (122) to the original locations on Input shaft assembly (65) .
Illustration 5 g01024466
12. Install Tooling (S) to Input shaft assembly (65) . Use a hoist in order to position Input shaft
assembly (65) to the original location in the transmission case assembly (11) . Install Input
shaft assembly (65) in the transmission case assembly (11) . Remove Tooling (S) from Input
shaft assembly (65) .
4/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Illustration 6 g00623297
Illustration 7 g00623294
13. Install seal rings (121) on piston (120) . Install both seal rings (121) with the sealing lips
facing toward the small diameter of piston (120) .
14. Place Forward shaft assembly (95) in the modified work bench or on blocks. Apply a light
coat of clean hydraulic oil on seal rings (121) . Install piston (120) at the original location on
Forward shaft assembly (95) . Slightly rotate piston (120) while the seal is being installed.
Ensure that the seal rings (121) are installed properly.
15. Install valve assembly (119) to the original location on Forward shaft assembly (95) .
5/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Illustration 8 g00623292
16. Install six clutch plates (117) and seven friction discs (118) in the original order on hub
assembly (115) . The splines on hub assembly (115) must align with the splines on the
friction discs (118) .
17. Install spring (116) in the original location on Forward shaft assembly (95) .
18. As one unit, install hub assembly (115) , six clutch plates (117) and seven friction discs
(118) to the original location on Forward shaft assembly (95) .
Illustration 9 g00623291
19. Use a second person in order to manually compress clutch assembly (113) on spring (116) .
20. Install two half rings (114) in the Forward shaft assembly (95) .
6/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Illustration 10 g00623665
21. Install the washer and thrust disc (112) to the original locations on Forward shaft assembly
(95) .
Illustration 11 g00623672
22. Install gear assembly (110) on Forward shaft assembly (95) and over clutch assembly
(113) . Align the spline teeth on the outer diameter of the clutch plates (117) with the splines
on the inside of gear assembly (110) . Ensure that gear assembly (110) is completely down
over the clutch assembly (113) .
7/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 12 g00623673
23. Install roller bearing (111) to the original location on Forward shaft assembly (95) .
Illustration 13 g00623736
24. Install two thrust discs (131) and thrust race (132) on Forward shaft assembly (95) . The
thrust discs (131) should not spin the thrust race (132) .
Illustration 14 g00623738
25. Heat inner bearing (109) to a maximum of 132 °C (270 °F). Install inner bearing (109) on
Forward shaft assembly (95) until inner bearing (109) contacts the bearing race.
26. Position Forward shaft assembly (95) , as shown. The weight of Forward shaft assembly
(95) is approximately 43 kg (95 lb). Place Forward shaft assembly (95) in the modified
work bench or blocks.
8/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Illustration 15 g00623287
27. Install lip seals (108) in piston (107) . Install lip seals (108) with the sealing lip toward the
small diameter of piston (107) .
28. Apply a light coat of clean hydraulic oil on lip seals (108) .
Illustration 16 g00623285
29. Install piston (107) to the original location on Forward shaft assembly (95) . Rotate the
piston slightly while the seal is being installed. Ensure that the lip seals are installed
properly.
30. Install valve assembly (106) to the original location on Forward shaft assembly (95) .
9/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SEB...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 17 g00623284
Note: Friction discs 1 and 7 are different from the remaining discs. Assemble friction discs
(1) and (7) with the grooved pattern toward the center of the clutch pack.
31. Install six clutch plates (105) and seven friction discs (103) in the original order on hub
assembly (102) . The splines on hub assembly (102) must align with the splines on the
friction plates.
32. Install spring (104) to the original location on Forward shaft assembly (95) .
33. As one unit, install hub assembly (102) , six clutch plates (105) , and seven friction discs
(103) to the original location on Forward shaft assembly (95) .
Illustration 18 g00623281
34. Use two people to manually compress hub assembly (100) on spring (94) . Install two half
rings (101) in Forward shaft assembly (95) .
10/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 19 g00623746
35. Install thrust disc and washer (99) on Forward shaft assembly (95) . The thrust disc should
not spin the washer.
Illustration 20 g00623747
Illustration 21 g00634016
36. Install gear assembly (97) on Forward shaft assembly (95) and over clutch assembly (100) .
Align the spline teeth on the outer diameter of the clutch plates with the splines on the
11/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. inside of gear assembly (97) . Ensure that the gear assembly (97) is completely down over
hub assembly (102) .
37. Install roller bearing (98) to the original location on Forward shaft assembly (95) .
38. Install the two thrust discs on Forward shaft assembly (95) .
Illustration 22 g00623756
39. Heat bearing (96) to a maximum of 132 °C (270 °F). Install bearing (96) on Forward shaft
assembly (95) until bearing (96) contacts the bearing race.
Illustration 23 g01024454
40. Install Tooling (S) in Forward shaft assembly (95) . Install Forward shaft assembly (95) to
the original location in the transmission cover assembly (11) . The weight of Forward shaft
assembly (95) is approximately 63.6 kg (140 lb). Remove Tooling (S) .
12/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 24 g00623276
41. Install the cup plug (not shown) from Reverse/Second shaft assembly (68) .
42. Install seals (93) and (94) with the sealing lip toward the small diameter of piston (92) .
Illustration 25 g00623270
43. Place Reverse/Second shaft assembly (68) in the modified work bench, or on blocks. Apply
a light coat of clean hydraulic oil on the lip seals. Install piston (92) to the original location
on Reverse/Second shaft assembly (68) . Rotate the piston slightly while the seal is being
installed. Ensure that the lip seals are installed properly.
44. Install valve assembly (91) to the original location on Reverse/Second shaft assembly (68) .
13/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 26 g00623269
45. Install six clutch plates (88) and seven friction disc (90) in the original order on hub
assembly (87) . The splines on the hub assembly (87) must align with the splines on the
friction discs (90) .
46. Install spring (89) in the original location on Reverse/Second shaft assembly (68) .
47. As one unit, install hub assembly (87) , six clutch plates (88) , and seven friction discs (90)
to the original location on Reverse/Second shaft assembly (68) .
Illustration 27 g00623265
48. Use two people to manually compress clutch plate (85) on spring (89) . Install two half rings
(86) in Reverse/Second shaft assembly.
14/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Illustration 28 g00623760
49. Install the washer and thrust disc (84) to the original locations on Reverse/Second shaft
assembly (68) . The thrust disc should not spin the washer.
50. Install gear assembly (82) on Reverse/Second shaft assembly (68) . Align the spline teeth on
the outer diameter of the clutch plates with the splines on the inside of gear assembly (82) .
Ensure that the gear assembly (82) is completely down over the clutch assembly (85) .
Illustration 29 g00634018
51. Install roller bearing (83) to the original location on Reverse/Second shaft assembly (68) .
15/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 30 g00634020
52. Install two thrust discs and one thrust race (133) .
Illustration 31 g00634021
53. Heat inner bearing (81) to a maximum of 132 °C (270 °F). Install inner bearing (81) on
Reverse/Second shaft assembly (68) until inner bearing (81) contacts the bearing race. The
thrust disc should not spin.
Illustration 32 g00623260
16/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 33 g00623261
54. Position Reverse/Second shaft assembly (68) , as shown. The weight of Reverse/Second
shaft assembly (68) is approximately 41 kg (90 lb). Place Reverse/Second shaft assembly
(68) in the modified work bench or on blocks.
55. Apply a light coat of clean hydraulic oil on the lip seals. Install lip seals (79) and (80) in
piston (78) . Install lip seals (79) and (80) with the sealing lip toward the small diameter of
the piston (78) . Rotate the piston slightly while the seal is being installed.
56. Install piston (78) to the original location on Reverse/Second shaft assembly (68) . Ensure
that the lip seals are installed properly.
57. Install wave spring (77) on Reverse/Second shaft assembly (68) .
Illustration 34 g00623259
58. Install clutch assembly (74) on Reverse/Second shaft assembly (68) . Position the three
clutch plates, the four friction disc, and the hub assembly in the original locations on
Reverse/Second shaft assembly (68) .
59. Install Tooling (K) and Tooling (H) on Reverse/Second shaft assembly (68) . Tighten
Tooling (J) on Tooling (H) in order to compress clutch assembly (74) . Install two half rings
(75) and two lock rings (76) in Reverse/Second shaft assembly (68) .
17/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. 60. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (74) . Remove Tooling (H) and Tooling (K) from clutch assembly (74) .
Illustration 35 g00623258
61. Install the thrust disc and the washer on Reverse/Second shaft assembly (68) .
62. Install the sleeve bearing (not shown) on Reverse/Second shaft assembly (68) .
63. Install gear assembly (73) on Reverse/Second shaft assembly (68) . Align the spline teeth on
the outer diameter of the clutch plates with the splines on the inside of gear assembly (73) .
Ensure that gear assembly (73) is down over the clutch assembly completely.
64. Install the thrust disc (not shown) and spacer (72) to the original locations on
Reverse/Second shaft assembly (68) .
Illustration 36 g00623761
65. Install gear (71) on Reverse/Second shaft assembly (68) .
66. Install spacer (70) on Reverse/Second shaft assembly (68) .
67. Heat bearing (69) to a maximum of 132 °C (270 °F). Install bearing (69) on Reverse/Second
shaft assembly (68) until bearing (69) contacts spacer (70) . Spacer (70) should not spin.
18/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 37 g01024451
68. Install Tooling (S) in Reverse/Second shaft assembly (68) . Place Reverse/Second shaft
assembly (68) to the original location in the transmission case assembly (11) . The weight of
Reverse/Second shaft assembly (68) is approximately 64 kg (141 lb). Remove Tooling (S) .
Illustration 38 g00623801
69. Install gear (67) to the original location on Input shaft assembly (65) .
70. Heat inner bearing (66) to a maximum of 132 °C (270 °F). Install inner bearing (66) on
Input shaft assembly (65) until inner bearing (66) contacts gear (67) . Gear (67) should be
tight on input shaft assembly (65) .
19/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 39 g00623250
71. Install seal extension ring (63) and seal ring (64) on piston (62) . Install seal (63) and seal
(64) with the sealing lips toward the small diameter of the piston (62) . Apply a light coat of
clean hydraulic oil on the lip seals of piston (62) .
Illustration 40 g00623249
72. Place First/Third shaft assembly (14) in the modified work bench, or on blocks. Install
piston (62) to the original location on First/Third shaft assembly (14) . Rotate the piston (62)
slightly while the seal is being installed. Ensure that the lip seals are installed properly.
73. Install wave spring (61) to the original location on First/Third shaft assembly (14) .
20/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 41 g00623248
74. As you install clutch assembly (58) to First/Third shaft assembly (14) , position the three
clutch plates, four friction disc and the hub assembly to the original locations on First/Third
shaft assembly (14) .
75. Install Tooling (K) and Tooling (H) on First/Third shaft assembly (14) . Tighten Tooling (J)
on Tooling (H) in order to compress clutch assembly (58) . Install two half rings (59) and
two lock rings (60) to First/Third shaft assembly (14) .
76. Carefully loosen the nut on Tooling (J) in order to relieve pressure from clutch assembly
(58) . Remove Tooling (K) and Tooling (H) .
Illustration 42 g00634025
77. Install the washer, the thrust disc, and the bearing sleeve to the original locations on
First/Third shaft assembly (14) .
78. Install gear assembly (57) in the original location on First/Third shaft assembly (14) and
over clutch assembly (58) . Align the spline teeth on the outer diameter of the clutch plates
with the splines on the inside of gear assembly (57) . Ensure that the gear assembly (57) is
completely down over clutch assembly (58) .
79. Install the thrust disc that was under gear (56) to the original location on First/Third shaft
assembly (14) .
21/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. 80. Install gear (56) to the original location on First/Third shaft assembly (14) . Install the thrust
disc that was on top of gear (56) .
81. Heat inner bearing (55) to a maximum of 132 °C (270 °F). Install inner bearing (55) on
First/Third shaft assembly (14) until inner bearing (55) contacts gear (56) . The thrust disc
that is under inner bearing (55) should not spin.
Illustration 43 g00623245
82. Install seal extension ring (53) and seal ring (54) on piston (52) . Install seal extension ring
(53) and seal ring (54) with the sealing lips toward the small diameter of the piston (52) .
Apply a light coat of hydraulic oil on the lip seals.
Illustration 44 g00623242
83. Rotate First/Third shaft assembly (14) in order to assemble the other end. The weight of
First/Third shaft assembly (14) is approximately 55 kg (121 lb). Place the First/Third shaft
assembly (14) on the modified work bench, or on blocks. Install piston (52) to the original
location on First/Third shaft assembly (14) . Rotate the piston slightly while the seal is being
installed. Ensure that the lip seals are installed properly.
84. Install wave spring (51) to the original location on First/Third shaft assembly (14) .
22/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
24. Illustration 45 g00623241
85. As you install clutch assembly (48) to First/Third shaft assembly (14) , position the five
clutch plates, six friction disc and the hub assembly to the original locations on First/Third
shaft assembly (14) .
86. Install Tooling (H) and Tooling (K) on First/Third shaft assembly (14) . Tighten Tooling (J)
on Tooling (H) in order to compress clutch assembly (48) . Install two half rings (49) and
two lock rings (50) on First/Third shaft assembly (14) .
87. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (48) . Remove Tooling (K) and Tooling (H) .
Illustration 46 g00623240
88. Install washer (47) and thrust disc (46) to the original locations on First/Third shaft
assembly (14) .
89. Install the sleeve bearing on First/Third shaft assembly (14) .
23/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
25. Illustration 47 g00623154
90. Install gear assembly (45) in the original location on First/Third shaft assembly (14) . Install
gear assembly (45) on First/Third shaft assembly (14) . Align the spline teeth on the outer
diameter of the clutch plates with the splines on the inside of gear assembly (45) . Ensure
that the gear assembly (45) is completely down over the clutch assembly.
91. Install thrust disc (44) on First/Third shaft assembly (14) .
Illustration 48 g00623802
92. Install gear assembly (43) on First/Third shaft assembly (14) .
93. Install the thrust disc that was under bearing (42) on First/Third shaft assembly (14) . Heat
bearing (42) to a maximum of 132 °C (270 °F). Install bearing (42) on First/Third shaft
assembly (14) until bearing (42) contacts gear assembly (43) . Thrust disc should not spin.
94. Install Tooling (S) (not shown) in First/Third shaft assembly (14) and place First/Third shaft
assembly (14) aside. The weight of First/Third shaft assembly (14) is approximately 89 kg
(196 lb).
24/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
26. Illustration 49 g00623150
Illustration 50 g00623149
95. Install seal ring (40) and seal extension ring (41) on piston (39) . Install seal ring (40) and
seal extension ring (41) with the sealing lip toward the small diameter of piston (39) .
96. Place High/Low shaft assembly (15) in the modified work bench or on blocks. Apply a light
coat of hydraulic oil on the lip seals. Install piston (39) to the original location on High/Low
shaft assembly (15) . Ensure that seal ring (40) , and seal extension ring (41) are installed
properly.
97. Install 15 springs (38) in the recess pockets in piston (39) .
98. Install one lip seal (37) on balance piston (39) .
99. Install balance piston (35) on High/Low shaft assembly (15) and in piston (39) . Ensure that
the guides that are located on balance piston (35) are placed in the center of each spring
(38) .
25/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
27. Illustration 51 g00623148
100. Install Tooling (K) and Tooling (N) on High/Low shaft assembly (15) and balance piston
(35) . Tighten Tooling (P) on Tooling (N) in order to compress balance piston (35) . Rotate
balance piston (35) slightly while the seal is being installed.
101. Use Tooling (Q) in order to install retaining ring (36) to High/Low shaft assembly (15) .
102. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from balance piston
(35) . Remove Tooling (B) from balance piston (35) and High/Low shaft assembly (15) .
Illustration 52 g00623145
26/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
28. Illustration 53 g00623141
103. Install the clutch assembly (32) to the original locations on High/Low shaft assembly (15) .
The clutch assembly (32) includes seven friction discs, eight clutch plates, and the hub
assembly.
104. Install Tooling (K) and Tooling (N) on High/Low shaft assembly (15) and clutch assembly
(32) . Tighten Tooling (P) on Tooling (N) in order to compress clutch assembly (32) .
105. Install two lock rings (34) and two half rings (33) to High/Low shaft assembly (15) .
106. Carefully loosen Tooling (P) on Tooling (N) in order to relieve pressure from clutch
assembly (32) . Remove Tool (K) and Tooling (N) from High/Low shaft assembly (15) and
clutch assembly (32) .
107. Install thrust disc and washer (31) to the original locations on High/Low shaft assembly
(15) .
Illustration 54 g00623805
108. Install gear assembly (30) in the original location on High/Low shaft assembly (15) . Install
gear assembly (30) on High/Low shaft assembly (15) . Align the spline teeth on the outer
diameter of the clutch plates with the splines on the inside of gear assembly (30) . Ensure
that gear assembly (30) is completely down over clutch assembly.
109. Install two thrust discs (29) and the two bearing sleeves on High/Low shaft assembly (15) .
110. Heat inner bearing (28) to a maximum of 132 °C (270 °F). Install inner bearing (28) on the
High/Low shaft assembly (15) until the inner bearing (28) contacts the thrust disc.
111. The thrust disc (29) should not spin.
27/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
29. Illustration 55 g00623134
Illustration 56 g00623132
112. Install seal extension ring (27) and seal ring (26) on piston (24) . Install seal extension ring
(27) and seal ring (26) with the sealing lips toward the small diameter of the piston (24) .
Apply a light coat of hydraulic oil on seal extension ring (27) and seal ring (26) .
113. Position High/Low shaft assembly (15) , as shown. The weight of the High/Low shaft
assembly (15) is 50 kg (110 lb). Place High/Low shaft assembly (15) on the modified work
bench, or on blocks. Install piston (24) to the original location on High/Low shaft assembly
(15) . Rotate the piston (24) slightly while the seal is being installed. Ensure that the seal
extension ring (27) and seal ring (26) are installed properly.
114. Install wave spring (25) to the original location on High/Low shaft assembly (15) .
28/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
30. Illustration 57 g00623131
115. As you install clutch assembly (21) to High/Low shaft assembly (15) , position the five
clutch plates, six friction discs, and the hub assembly to the original locations on High/Low
shaft assembly (15) .
116. Install Tooling (K) and Tooling (H) on High/Low shaft assembly (15) and clutch assembly
(21) . Tighten Tooling (J) on Tooling (H) in order to compress clutch assembly (21) .
117. Install two half rings (22) and two lock rings (23) to High/Low shaft assembly (15) .
118. Carefully loosen Tooling (J) on Tooling (H) in order to relieve pressure from clutch
assembly (21) . Remove Tooling (H) and Tooling (K) from High/Low shaft assembly (15)
and clutch assembly (21) .
Illustration 58 g00623129
119. Install the thrust disc, the two sleeve bearings and washer (20) to the original locations on
High/Low shaft assembly (15) .
29/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
31. Illustration 59 g00623806
Illustration 60 g00623126
120. Install gear assembly (18) , align the internal spline of the cylinder welded to the external
teeth of the clutch. Ensure that gear assembly (18) is completely down over clutch assembly
(23) .
121. Install thrust disc (19) that was under rotor (17) to High/Low shaft assembly (15) . Heat
rotor (17) to a maximum of 135 °C (275 °F). Install rotor (17) to High/Low shaft assembly
(15) until rotor (17) makes contact with the shoulder of shaft assembly (15) . Ensure that
rotor (17) is completely down against the shoulder of shaft assembly (15) . Thrust disc (19)
should spin freely.
30/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
32. Illustration 61 g00623807
122. Heat bearing (16) to a maximum of 135 °C (275 °F). Install bearing (16) to High/Low shaft
assembly (15) until bearing (16) makes contact with rotor (17) .
Illustration 62 g00634111
123. Install Tooling (F) in High/Low shaft assembly (15) and place High/Low shaft assembly
(15) next to First/Third shaft assembly (14) and in Tooling (F) . The weight of High/Low
shaft assembly (15) is approximately 89 kg (195 lb). The use of Tooling (F) will hold
First/Third shaft assembly (14) and High/Low shaft assembly (15) to the proper height of
the gear mesh. This will allow Tooling (D) to be installed properly. Slide the two shafts
together until the gear mesh is obtained.
31/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
33. Illustration 63 g00849491
124. Use Tooling (C) and Tooling (E) to install Tooling (D) on First/Third shaft assembly (14)
and High/Low shaft assembly (15) . First/Third shaft assembly (14) and High/Low shaft
assembly (15) must be installed in the transmission cover assembly (11) together.
125. Attach a suitable lifting device to Tooling (D) . Carefully install First/Third shaft assembly
(14) and High/Low shaft assembly (15) to the original locations in the transmission case
assembly. The weight of the two shaft assemblies is 177 kg (390 lb).
Illustration 64 g00623113
126. Position tube assembly (13) and the O-ring (not shown) to the original locations in the
transmission case assembly. Install three bolts (12) to secure tube assembly (13) to the
transmission case assembly. Tighten bolts (12) to a torque of 55 ± 10 N·m (40 ± 7 lb ft).
127. Clean the flanges of both halves of the transmission cover assembly (11) and the
transmission case assembly (3) . Apply a 3.0 mm (0.12 inch) bead of Tooling (T) to the joint
between transmission case assembly (3) and transmission cover assembly (11) .
32/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
34. Suggest:
If the above button click is invalid.
Please download this document
first, and then click the above link
to download the complete manual.
Thank you so much for reading
35. Illustration 65 g00623110
Note: Remove Tooling (B) from transmission cover assembly (11) .
128. Attach Tooling (A) and a suitable lifting device to the transmission cover assembly (11) .
Carefully install the transmission cover assembly (11) to the transmission case assembly
(3) . Be careful not to bind on the locating pins during the installation.
Illustration 66 g00623108
129. Install spring pin (10) in seal carrier (5) .
130. Install three seal rings (9) on seal carrier (5) .
131. Install O-ring seals (8) in seal carriers (5) .
33/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
36. Illustration 67 g00623105
Illustration 68 g00636998
132. Install Tooling (A) (not shown) in seal carrier (5) . Carefully install seal carrier (5) in the
original transmission case assembly bore (7) . Ensure that spring pin (10) is installed in the
proper location in the shaft assembly.
133. Install two bolts (6) to secure seal carrier (5) to the shaft assembly. Tighten bolts (6) to a
torque of 55 ± 10 N·m (41 ± 7 lb ft).
134. Repeat Steps 132 and 133 in order to install the remaining three seal carriers to the original
locations in the transmission case assembly (11) .
34/35
12H Motor Grader 4XM00001-UP (MACHINE) POWERED BY 3306B Engine(SE...
2021/1/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...