This product catalogue from Isolmant provides information on their range of insulation products for construction applications. Isolmant specializes in acoustic and thermal insulation solutions focused on energy savings and compliance with regulations. The catalogue outlines their various product lines for impact sound insulation, airborne sound insulation, outdoor sound insulation, and special products. It provides details on each product's thickness, sound insulation performance, thermal resistance, sizes and packaging. The document aims to inform construction companies about Isolmant's innovative insulation solutions.
Eternabond BWG features a durable and UV resistant polyethylene face which is laminated to a patented micro-sealant backing with ’quick release’ silicone liner.
Waterproofing tape is activated under pressure and primes the construction or building substrate. Etermabond instantly bonds to that surface to form a waterproof and airtight seal.
(www.indiamart.com/ufcinternational) Committed towards accomplishing a high level of patron satisfaction, we are betrothed in offering a broad gamut of Interior Products. Developed and made-up at par with the internationally accepted guidelines and quality values, some of our offered products comprise High Pressure Laminate, Laminate Decorative Panels and Exterior Wall Cladding. Offered by us at affordable rates, we make sure their flawlessness and reliability to our precious patrons.
Aluminum Seal creates a protective air and vapor barrier on surfaces where corrosion and abrasion resistance is required.
Waterproofing tape is activated under pressure and primes the construction or building substrate. Etermabond instantly bonds to that surface to form a waterproof and airtight seal.
Eternabond BWG features a durable and UV resistant polyethylene face which is laminated to a patented micro-sealant backing with ’quick release’ silicone liner.
Waterproofing tape is activated under pressure and primes the construction or building substrate. Etermabond instantly bonds to that surface to form a waterproof and airtight seal.
(www.indiamart.com/ufcinternational) Committed towards accomplishing a high level of patron satisfaction, we are betrothed in offering a broad gamut of Interior Products. Developed and made-up at par with the internationally accepted guidelines and quality values, some of our offered products comprise High Pressure Laminate, Laminate Decorative Panels and Exterior Wall Cladding. Offered by us at affordable rates, we make sure their flawlessness and reliability to our precious patrons.
Aluminum Seal creates a protective air and vapor barrier on surfaces where corrosion and abrasion resistance is required.
Waterproofing tape is activated under pressure and primes the construction or building substrate. Etermabond instantly bonds to that surface to form a waterproof and airtight seal.
Suncool agriculture films for Greenhouse covers, Mulching, Pond LiningEssen Multipack Ltd
This slide show will give you information about how to chose a best quality plastic film or sheet to be used as greenhouse covering. Also it tell about various options available for Plastics Mulching.
Murano Composite Panel is a Premium Grooved Acoustic Wood Panel. It has a natural wood veneer finish incorporated with the Acoustic insulation to for a complete acoustic wood panel.Suitable for both walls and Ceilings.
FRP for masonry, stone, flat/curved arch terracotta and cindercrete stabilization with a Class A Fire Rating for interior, exterior, and above or below grade (wet) applications.
FAIRFLO 101 is aimed to achieve increased workability without loss of strength. FAIRFLO 101 is specifically formulated for Ready-mix concrete and household purposes. Reduction in cement without loss of workability or strength can be achieved. It can reduce water to cement ratio for any given workability. It Confirms to BS-5075 : 1982 Part 1; IS-9103 : 1979 and ASTM C-494 Type A.
The Company
Founded in 1998 in order to enter into the Brazilian telecommunications market, Fechometal began to develop a production line dedicated to mooring items.
Throughout its history, it has specialized in high quality stainless steel material, developing items to new industrial markets. Improved its industrial settings by investing in technology and incorporated in its production last generation technical resources, based on the constant improvement of its products.
Currently Fechometal develops products for various industries: Telecommunications, Energy, Naval, Construction, Automotive, Aviation, Municipal, Signalization and Agriculture. Its production line includes tapes, closures, self locking clamps, supports, tools, identification tags, among other items, with different measures and models.
One of the most important manufacturers of stainless steel bands and buckles in Brazil, Fechometal has the recognition of the most important companies in Brazil for the excellence of their products, offering support from the development of the idea to the manufacture of the final product.
To meet the demands required of its customers, Fechometal maintains a broad pattern of development and a modern logistics system. Fechometal counts with reference equipment and a highly skilled team of professionals in a manufacturing area of 800 m2, providing for its clients better quality x cost equation in an agile and flexible way, with accordance to the requirements of the global market.
Fechometal exports to Latin America, the United States and Europe, following all international norms and standards. This integration is another factor that leads us to have sufficient flexibility to meet the quality requirements of these markets.
True to the entrepreneurial spirit of its founders, Fechometal has a major partnership commitment with its customers, suppliers and employees.
(https://www.indiamart.com/ufcinternational) Our offered products are extensively recognized for an extensive variety of purposes and can be availed from us in urgent and bulk orders within the assured time. For all the business processes to take place in the most effective way, we have been supported by trained and skilled personnel. Along with this, this facility is been divided by us for preserving evenness at our work place. In addition, the crew of personnel hired by us is well familiar with the knowledge of their respective field and completes all their tasks within the assured time as per the requirements and provisions mentioned by our patrons. From amid the best talents present in the industry, these are hired after stern rounds of interviews.
Suncool agriculture films for Greenhouse covers, Mulching, Pond LiningEssen Multipack Ltd
This slide show will give you information about how to chose a best quality plastic film or sheet to be used as greenhouse covering. Also it tell about various options available for Plastics Mulching.
Murano Composite Panel is a Premium Grooved Acoustic Wood Panel. It has a natural wood veneer finish incorporated with the Acoustic insulation to for a complete acoustic wood panel.Suitable for both walls and Ceilings.
FRP for masonry, stone, flat/curved arch terracotta and cindercrete stabilization with a Class A Fire Rating for interior, exterior, and above or below grade (wet) applications.
FAIRFLO 101 is aimed to achieve increased workability without loss of strength. FAIRFLO 101 is specifically formulated for Ready-mix concrete and household purposes. Reduction in cement without loss of workability or strength can be achieved. It can reduce water to cement ratio for any given workability. It Confirms to BS-5075 : 1982 Part 1; IS-9103 : 1979 and ASTM C-494 Type A.
The Company
Founded in 1998 in order to enter into the Brazilian telecommunications market, Fechometal began to develop a production line dedicated to mooring items.
Throughout its history, it has specialized in high quality stainless steel material, developing items to new industrial markets. Improved its industrial settings by investing in technology and incorporated in its production last generation technical resources, based on the constant improvement of its products.
Currently Fechometal develops products for various industries: Telecommunications, Energy, Naval, Construction, Automotive, Aviation, Municipal, Signalization and Agriculture. Its production line includes tapes, closures, self locking clamps, supports, tools, identification tags, among other items, with different measures and models.
One of the most important manufacturers of stainless steel bands and buckles in Brazil, Fechometal has the recognition of the most important companies in Brazil for the excellence of their products, offering support from the development of the idea to the manufacture of the final product.
To meet the demands required of its customers, Fechometal maintains a broad pattern of development and a modern logistics system. Fechometal counts with reference equipment and a highly skilled team of professionals in a manufacturing area of 800 m2, providing for its clients better quality x cost equation in an agile and flexible way, with accordance to the requirements of the global market.
Fechometal exports to Latin America, the United States and Europe, following all international norms and standards. This integration is another factor that leads us to have sufficient flexibility to meet the quality requirements of these markets.
True to the entrepreneurial spirit of its founders, Fechometal has a major partnership commitment with its customers, suppliers and employees.
(https://www.indiamart.com/ufcinternational) Our offered products are extensively recognized for an extensive variety of purposes and can be availed from us in urgent and bulk orders within the assured time. For all the business processes to take place in the most effective way, we have been supported by trained and skilled personnel. Along with this, this facility is been divided by us for preserving evenness at our work place. In addition, the crew of personnel hired by us is well familiar with the knowledge of their respective field and completes all their tasks within the assured time as per the requirements and provisions mentioned by our patrons. From amid the best talents present in the industry, these are hired after stern rounds of interviews.
Cement Bonded Particle Board Manufacturer in India -Bison Panel Product Guide...BisonPanel1
Bison Panel or also known as Bison Board is a Cement Bonded Particle Board made out of Cement and Mineralised wood particles.
As Bison Panels are extremely Durable, Flexible, Fire and Water resistant in nature, these multi – purpose boards can be used for both Interior and Exterior applications ranging from False Ceiling, Partitions, Internal and External Wall Cladding, Furniture, Wardrobes etc.
Bison Panels / Bison boards are Eco – friendly and Non – Toxic in Nature. It is a Non-carcinogenic material and 100% asbestos free.
https://bisonpanel.com
This is regarding the installation in the building signs and the content will cover the effects of insulation in different buildings it also contains a lot of pictures to help readers understand the materials
O uso de acopladores Ancon simplificara concepção e construção em betão armado e reduz a quantidade de reforço necessário. Os Acopladores Ancon para União de varões de aço nervurado existem em três conceitos: Aperto Lateral - Rosca Cónica - Rosca Direita Apresenta ainda suloções de posicionamento e transição de diâmetros.
Deantape is a Asia company mainly engaged in the industrial tape business, the optronics business and the life science business. The Company operates in three business segments. The Industrial Tapes segment is engaged in the manufacture and sale of basic functional materials such as bonding materials and protective materials, as well as automotive materials. The Optronics segment is engaged in the manufacture and sale of information functional materials, printed circuits and process materials. The Life Science segment is engaged in the manufacture and sale of medical related materials. The Company is also engaged in the manufacture and sale of polymer separation membranes and other products.
Murano Acoustic Wall and Ceiling Panels are a highly decorative and acoustic panel. Available in Real wood veneers,High Gloss pain, decorative laminates. Reduce noise in Lecture theaters, Auditoriums etc
La colección Allura Flex Decibel se compone de 18 colores energéticos, sorprendentes y posee una reducción del sonido de impacto de 19dB. Aunque se trata de un producto mucho más ligero que las losetas autoportantes convencionales, su construcción innovadora que incluye una doble capa de fibra de vidrio ofrece propiedades de instalación parecidas en cuanto a rapidez y estabilidad dimensional.
Flex Decibel se instala de forma rápida ya sea por ejemplo en oficinas en funcionamiento, proyectos de vivienda y en espacios comunes o tiendas.
http://bit.ly/1emiG8r
Similar to Catalogo prodotti 2018_eng_t8_qsp5e (20)
Student information management system project report ii.pdfKamal Acharya
Our project explains about the student management. This project mainly explains the various actions related to student details. This project shows some ease in adding, editing and deleting the student details. It also provides a less time consuming process for viewing, adding, editing and deleting the marks of the students.
Water scarcity is the lack of fresh water resources to meet the standard water demand. There are two type of water scarcity. One is physical. The other is economic water scarcity.
Welcome to WIPAC Monthly the magazine brought to you by the LinkedIn Group Water Industry Process Automation & Control.
In this month's edition, along with this month's industry news to celebrate the 13 years since the group was created we have articles including
A case study of the used of Advanced Process Control at the Wastewater Treatment works at Lleida in Spain
A look back on an article on smart wastewater networks in order to see how the industry has measured up in the interim around the adoption of Digital Transformation in the Water Industry.
Immunizing Image Classifiers Against Localized Adversary Attacksgerogepatton
This paper addresses the vulnerability of deep learning models, particularly convolutional neural networks
(CNN)s, to adversarial attacks and presents a proactive training technique designed to counter them. We
introduce a novel volumization algorithm, which transforms 2D images into 3D volumetric representations.
When combined with 3D convolution and deep curriculum learning optimization (CLO), itsignificantly improves
the immunity of models against localized universal attacks by up to 40%. We evaluate our proposed approach
using contemporary CNN architectures and the modified Canadian Institute for Advanced Research (CIFAR-10
and CIFAR-100) and ImageNet Large Scale Visual Recognition Challenge (ILSVRC12) datasets, showcasing
accuracy improvements over previous techniques. The results indicate that the combination of the volumetric
input and curriculum learning holds significant promise for mitigating adversarial attacks without necessitating
adversary training.
NO1 Uk best vashikaran specialist in delhi vashikaran baba near me online vas...Amil Baba Dawood bangali
Contact with Dawood Bhai Just call on +92322-6382012 and we'll help you. We'll solve all your problems within 12 to 24 hours and with 101% guarantee and with astrology systematic. If you want to take any personal or professional advice then also you can call us on +92322-6382012 , ONLINE LOVE PROBLEM & Other all types of Daily Life Problem's.Then CALL or WHATSAPP us on +92322-6382012 and Get all these problems solutions here by Amil Baba DAWOOD BANGALI
#vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore#blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #blackmagicforlove #blackmagicformarriage #aamilbaba #kalajadu #kalailam #taweez #wazifaexpert #jadumantar #vashikaranspecialist #astrologer #palmistry #amliyaat #taweez #manpasandshadi #horoscope #spiritual #lovelife #lovespell #marriagespell#aamilbabainpakistan #amilbabainkarachi #powerfullblackmagicspell #kalajadumantarspecialist #realamilbaba #AmilbabainPakistan #astrologerincanada #astrologerindubai #lovespellsmaster #kalajaduspecialist #lovespellsthatwork #aamilbabainlahore #Amilbabainuk #amilbabainspain #amilbabaindubai #Amilbabainnorway #amilbabainkrachi #amilbabainlahore #amilbabaingujranwalan #amilbabainislamabad
CFD Simulation of By-pass Flow in a HRSG module by R&R Consult.pptxR&R Consult
CFD analysis is incredibly effective at solving mysteries and improving the performance of complex systems!
Here's a great example: At a large natural gas-fired power plant, where they use waste heat to generate steam and energy, they were puzzled that their boiler wasn't producing as much steam as expected.
R&R and Tetra Engineering Group Inc. were asked to solve the issue with reduced steam production.
An inspection had shown that a significant amount of hot flue gas was bypassing the boiler tubes, where the heat was supposed to be transferred.
R&R Consult conducted a CFD analysis, which revealed that 6.3% of the flue gas was bypassing the boiler tubes without transferring heat. The analysis also showed that the flue gas was instead being directed along the sides of the boiler and between the modules that were supposed to capture the heat. This was the cause of the reduced performance.
Based on our results, Tetra Engineering installed covering plates to reduce the bypass flow. This improved the boiler's performance and increased electricity production.
It is always satisfying when we can help solve complex challenges like this. Do your systems also need a check-up or optimization? Give us a call!
Work done in cooperation with James Malloy and David Moelling from Tetra Engineering.
More examples of our work https://www.r-r-consult.dk/en/cases-en/
Hierarchical Digital Twin of a Naval Power SystemKerry Sado
A hierarchical digital twin of a Naval DC power system has been developed and experimentally verified. Similar to other state-of-the-art digital twins, this technology creates a digital replica of the physical system executed in real-time or faster, which can modify hardware controls. However, its advantage stems from distributing computational efforts by utilizing a hierarchical structure composed of lower-level digital twin blocks and a higher-level system digital twin. Each digital twin block is associated with a physical subsystem of the hardware and communicates with a singular system digital twin, which creates a system-level response. By extracting information from each level of the hierarchy, power system controls of the hardware were reconfigured autonomously. This hierarchical digital twin development offers several advantages over other digital twins, particularly in the field of naval power systems. The hierarchical structure allows for greater computational efficiency and scalability while the ability to autonomously reconfigure hardware controls offers increased flexibility and responsiveness. The hierarchical decomposition and models utilized were well aligned with the physical twin, as indicated by the maximum deviations between the developed digital twin hierarchy and the hardware.
3. Real solutions for real issues.
Isolmant’s mission is to provide construction
companies with a range of innovative solutions for
acoustic and thermal insulation.
Itsfocusisonenergysaving,compliancewithacoustic
and thermal insulation regulations as well as with
sustainability protocols. All the Isolmant’s functions
- Manufacturing, Sales, Marketing, Research, &
Development - are committed to fulfil this mission:
sustainability.
That also means to manufacture products in line with
the highest standards of construction.
Isolmant releases its products only after strict quality
controls, laboratory tests and installation tests.
Thanks to this process, our products are suitable
for their applications and the on-site performances
confirming their lab results.
Great attention also goes to the range of accessories,
specifically designed for the usage. The accessories
also
allow a state of the art installation and time saving.
Moreover, our accessories enhance each range best
performances.
6. Full technical specifications at www.isolmant.com6
> ISOLMANT SPECIAL
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> To be installed with the embossed and screen printed side facing
upwards.
THICKNESS Approx. 3 - 5 - 10 - 15 mm
IMPACT SOUND INSULATION
ΔLw
= 19 dB (3 mm version) Value calculated according to EN ISO 12354-2
and UNI/TR 11175
ΔLw
= 25.5 dB (5 mm version) Certified value
ΔLw
= 28 dB (10 mm version) Certified value
DYNAMIC STIFFNESS
s’ = 80 MN/m3
(3 mm version)
s’ = 60 MN/m3
(5 mm version)
s’ = 32 MN/m3
(10 mm version)
THERMAL CHARACTERISTICS
λ = 0.035 W/mK
c = 2100 J/kgK
μ = 3600
SIZE
Rolls of:
1.50 m x 5 0 m (h x L) = 150 m2
(3 mm version)
1.50 m x 50 m (h x L) = 75 m2
(5 mm and 10 mm version)
1.50 m x 30 m (h x L) = 45 m2
(15 mm version)
Product with overlaps (10 and 15 mm version)
PACKAGING Single rolls
Innovative Isolmant with embossed and screen printed upper side.
This product is made of high quality expanded closed-cell physically
cross-linked polyethylene.
Isolmant Special, upon request, it is available covered with a
special tissue anti-tearing.
Production cost 0,86 €/m2
(only versions h.1,50)
> Conditions of use
Isolmant Special is recommended for impact sound insulations of horizontal partitions. This product is suitable for
applications between the levelling substrate and the screed in double-layer flooring. It ensures performance and quality
over the time thanks to its physical characteristics. The finishing screed should be at least 5 cm (for Isolmant Special 3
and 5 mm) or at least 7 cm (for Isolmant Special 10 mm). Screeds with lower thickness should be reinforced by means of a
suitable metal mesh or fibres.
> Item specifications
The resilient layer is made of second-generation expanded closed-cell physically cross-linked polyethylene. This
product ensures an even performance and high compressive strength over the time (type Isolmant Special). The
company logo should be placed in a visible position. Product with overlaps (10 and 15 mm version).
Density 30 kg/m3
. Thickness ... mm (3 - 5 - 10 - 15 mm). Dynamic stiffness MN/m3
(80 - 60 - 32 MN/m3
for the 3 - 5 - 10
mm versions respectively).
Rt
= 0.086 m2
K/W (3 mm version)
Rt
= 0.142 m2
K/W (5 mm version)
Rt
= 0.284 m2
K/W (10 mm version)
Rt
= 0.426 m2
K/W (15 mm version)
7. Full technical specifications at www.isolmant.com 7
> ISOLMANT SPECIAL 5
RENOVATION
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> To be installed with the embossed and screen printed side facing
upwards.
THICKNESS Approx. 5 mm
IMPACT SOUND INSULATION ΔLw
= 25.5 dB Certified value
DYNAMIC STIFFNESS s’ = 60 MN/m3
THERMAL CHARACTERISTICS
λ = 0.035 W/mK
c = 2100 J/kgK
μ = 3600
SIZE
Rolls of:
1.00 m x 15 m (h x L) = 15 m2
PACKAGING Single rolls
Innovative Isolmant with embossed and screen printed upper side.
This product is made of high quality expanded closed-cell physically
cross-linked polyethylene.
> Conditions of use
Isolmant Special is recommended for impact sound insulations of horizontal partitions. This product is suitable for
applications between the levelling substrate and the screed in double-layer flooring. It ensures performance and quality
over the time thanks to its physical characteristics. The finishing screed should be at least 5 cm (Isolmant Special 5 mm).
Screeds with lower thickness should be reinforced by means of a suitable metal mesh or fibres.
> Item specifications
The resilient layer is made of second-generation expanded closed-cell physically cross-linked polyethylene. This
product ensures an even performance and high compressive strength over the time (type Isolmant Special). The
company logo should be placed in a visible position. Product with overlaps (10 and 15 mm version).
Density 30 kg/m3
. Thickness 5 mm. Dynamic stiffness MN/m3
60 MN/m3
Rt
= 0.142 m2
K/W
8. Full technical specifications at www.isolmant.com8
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> ISOLMANT UNDERPLUSBLACK.E
> To be laid with the fibre facing down.
THICKNESS Approx. 7 mm
IMPACT SOUND INSULATION ΔLw
= 26 dB Value certified according to UNI EN ISO 10140
DYNAMIC STIFFNESS s’ = 17 MN/m3
Tested value according to EN 29052-1
THERMAL RESISTANCE Rt
= 0,171 m2
K/W
SIZE
Rolls of:
1,50 m x 50 m (h x L) = 75 m2
Product with overlaps.
Once overlapped, the sheets should be sealed by means of
Isolmant Nastro Telato or Isolmant Fascia Nastro
PACKAGING Single rolls
Product comprising crosslinked closed-cell polyethylene foam,
about 3 mm thick, joined on the underside to FIBTEC XF1 (special
needled fibre produced to specifications designed to provide
optimum noise reduction).
> Conditions of use
Isolmant UnderPlusBlack.E guarantees high impact noise insulation and also better airborne noise reduction.Isolmant
UnderPlusBlack.E is particularly suitable for two-layer structure, with the floating screed installed on the leveling
layer. It requires finishing screed thickness of at least 5 cm; for lower thickness it is recommended to reinforce the
screed with suitable metal mesh or fibre. Care must be taken when applying ceramic tiles on fresh screed.
> Item specifications
Resilient layer of 3 mm crosslinked closed-cell polyethylene foam, joined on the underside to a needled fibre to improve
soundproofing (such as Isolmant UnderPlus Black.E). To be laid with the fibre facing down.
Product with overlaps. Thickness approximately 7 mm. Dynamic stiffness 17 MN/m3
.
9. Full technical specifications at www.isolmant.com 9
> ISOLMANT MONOPLUS
> To be positioned with the screen-printed fabric facing upwards.
THICKNESS Approx. 7 mm
IMPACT SOUND INSULATION ΔLw
= 26 dB Value calculated according to EN ISO 12354/-2 and UNI/TR 11175
DYNAMIC STIFFNESS s’ = 19 MN/m3
THERMAL RESISTANCE Rt
= 0.171 m2
K/W
SIZE
Rolls of:
1.50 m x 50 m (h x L) = 75 m2
This product comes with adhesive flap to seal the overlapping
fabric
PACKAGING Single rolls
Product made of 3 mm Isolmant with the upper side bonded to
FIBTEC XT2 (screen printed anti-tearing fleece) and the lower side
to FIBTEC XS1 (special needle-punched fibre produced according to
specifications designed to provide a better impact sound insulation).
> Conditions of use
Isolmant MonoPlus is recommended for impact sound insulations with floating screed. It is also suitable for single-
layer application in which the direct installation of building plants on the resilient layer requires tear resistance and
protection to avoid damaging the insulating material. The product can be installed with low thickness screed (at least
5 cm).
> Item specifications
The resilient layer is made of expanded closed-cell physically cross-linked polyethylene bonded, on the lower side, to
a special needle-punched white fibre that is conceived to enhance the acoustic performance. On the upper side, it is
bonded to a screen-printed anti-tearing fibre (type Isolmant MonoPlus). The product comes with adhesive overlapping
flap. Thickness approx. 7 mm. Dynamic stiffness 19 MN/m3
.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
10. Full technical specifications at www.isolmant.com10
> ISOLMANT RADIANTE
> To be installed with the aluminate-coated side facing upwards.
THICKNESS Approx. 6 - 8 mm
IMPACT SOUND INSULATION
ΔLw
= 25 dB (6 mm version) Value certified according to the EN ISO 140/8
ΔLw
= 30 dB (8 mm version) Value calculated according to EN ISO 12354-2
and UNI/TR 11175
DYNAMIC STIFFNESS
s’ = 21 MN/m3
(6 mm version)
s’ = 15 MN/m3
(8 mm version)
THERMAL RESISTANCE
Rt
= 0.168 m2
K/W (6 mm version)
Rt
= 0.254 m2
K/W (8 mm version)
SIZE
Rolls of:
1.50 m x 50 m (h x L) = 75 m2
(6 mm version)
1.50 m x 25 m (h x L) = 37.5 m2
(6 mm version)
1.50 m x 25 m (h x L) = 37.5 m2
(8 mm version)
Product with overlaps. Once overlapped, the sheets should be sealed
by means of Isolmant Nastro Telato or Isolmant Fascia Nastro
PACKAGING Single rolls
Product made of HD 3 mm Isolmant Special or 5 mm Isolmant with
the upper side bonded to a radiant, embossed aluminate coated film
and the lower side bonded to FIBTEC XF2 (special needle-punched
fibre produced according to specifications designed to provide a
better noise reduction).
> Conditions of use
Isolmant Radiante is specific for applications with underfloor heating or cooling system. Thanks to its aluminate
reflective film, it can block any downward loss of heat. This product fits for low thickness screed installations with
thin thermal insulation panels. An acoustic resilient layer is always required, because thermal panels do not provide
acoustic insulation (except in specific cases).
> Item specifications
Resilient layer made of 3 or 5 mm crosslinked closed-cell polyethylene foam with the upper side bonded to a radiant,
embossed aluminate coated film and the lower side bonded to FIBTEC XF2 (special needle-punched fibre produced
according to specifications designed to provide a better noise reduction). To be installed with the aluminate-coated
side facing upwards. Product with overlaps. Thickness approx. 6 or 8 mm. Dynamic stiffness 21 MN/m3
or 15 MN/m3
respectively for 6 or 8 mm versions.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
11. Full technical specifications at www.isolmant.com 11
> ISOLMANT UNDERSPECIAL
Product made of 5 to 10 mm Isolmant Special with the lower side
bonded to FIBTEC XF1 (special needle-punched fibre produced
according to specifications conceived to provide a better noise
reduction).
> Conditions of use
Isolmant UnderSpecial ensures high impact sound insulation in floating screed application. It is suitable when a
higher air-born sound insulation is required. In particular, this product is recommended in double-layer application.
It needs 6 cm (for Isolmant Underspecial 8 mm) or 7 cm (for Isolmant Underspecial 13 mm) screeds. Screeds with
lower thickness should be reinforced by means of a suitable metal mesh or fibres. Attention must be paid in case of
dry shake installation of ceramic tiles.
> Item specifications
The resilient layer is made of expanded closed-cell physically cross-linked polyethylene. The upper side is embossed
and screen-printed. The lower side is bonded to a special needle-punched fibre that is conceived to enhance the
acoustic performance (Isolmant UnderSpecial). This product should be positioned with the fibre side facing down.
Product with overlaps. Thickness in mm (approx. 8 or 13 mm). Dynamic stiffness MN/m3
(respectively 11 MN/m3
or 9
MN/m3
for 8 or 13 mm version).
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
>To be positioned with the fibre side facing down.
THICKNESS Approx. 8 - 13 mm
IMPACT SOUND INSULATION ΔLw
= 34 dB (for both types) Certified value
DYNAMIC STIFFNESS
s’ = 11 MN/m3
(8 mm version)
s’ = 9 MN/m3
(13 mm version)
THERMAL RESISTANCE
Rt
= 0.234 m2
K/W (8 mm version)
Rt
= 0.376 m2
K/W (13 mm version)
SIZE
Rolls of:
1,50 m x 25 m (h x L) = 37,5 m2
(versione 8 mm)
1,50 m x 50 m (h x L) = 75 m2
(versione 8 mm)
1,50 m x 25 m (h x L) = 37,5 m2
(versione 13 mm)
Product with overlaps.
Once overlapped, the sheets should be sealed by means of
Isolmant Fascia Nastro or Isolmant Nastro Telato.
PACKAGING Single rolls
12. Full technical specifications at www.isolmant.com12
> ISOLMANT UNDERSPECIAL EVO
IMPACT SOUND INSULATION ΔLw
= 24 dB (according to official test report)
DYNAMIC STIFFNESS
s’ = 55 MN/m3
THERMAL RESISTANCE Rt
= 0,111 m2
K/W
SIZE
Rolls of 1 m x 20 m (h x L) = 20 m2
Once overlapped, the sheets should be sealed by means of Isolmant Nastro
Telato. Isolmant UnderSpecial EVO_BV comes with adhesive overlapping
flap to connect and seal the sheets.
THICKNESS 4 mm approx.
PACKAGING Single rolls
Product made of 1,5 mm High Density Isolmant with the lower side bonded
to FIBTEC XF2 (special needle-punched fibre produced according to
specifications conceived to provide a better noise reduction).
Isolmant Underspecial EVO_BV bonded to a HDPE vapour barrier available
on request (version BV).
To be positioned with the fibre side facing down.
> Conditions of use
Isolmant UnderSpecial EVO is specifically conceived to optimise the acoustic performance of floating screed made of self-
levelling compound. The density and the low thickness of these screeds (no less than 3 cm) cause vibration phenomena
at high frequencies and Isolmant UnderSpecial EVO is designed to avoid this effect. In addition, thanks to its top adhesive
fabric, Isolmant UnderSpecial EVO provides a perfect sealing for fluid castings screed.
> Item specifications
The resilient layer is made of HD expanded closed-cell cross-linked polyethylene bonded to a special needle-punched
fibre that is conceived to enhance the acoustic performance (type Isolmant UnderSpecial EVO). This product should be
positioned with the fibre side facing down. Thickness approx. 4 mm. Dynamic stiffness 55 MN/m3
.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
13. Full technical specifications at www.isolmant.com 13
> ISOLMANT UNDERSLIM
> Conditions of use
Isolmant UnderSlim is recommended for floating flooring with reduced thickness screeds (not less than 5 cm). In fact,
finishing screeds with reduced thickness show a very high risk of cracking. Thanks to its special fibre and its high density
Isolmant Special layer, this product provides a high level of impact sound performance and reduced risks of cracks.
> Item specifications
The resilient layer is made of HD expanded closed-cell physically cross-linked polyethylene (approx. 50 kg/m3
). The
upper side is embossed and screen-printed. Its lower side is bonded to a special needle-punched fibre that is conceived
to enhance the acoustic performance (Isolmant UnderSlim). This product should be positioned with the fibre side
facing down. Product with overlaps. Thickness approx. 5 mm. Dynamic stiffness 21 MN/m3
.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> ISOLMANT BIPLUS
> To be positioned with the screen-printed fabric facing upwards.
THICKNESS Approx. 9 - 14 mm
IMPACT SOUND INSULATION ΔLw
= 34 dB (for both types) Certified value
DYNAMIC STIFFNESS
s’ = 11 MN/m3
(9 mm version)
s’ = 9 MN/m3
(14 mm version)
THERMAL RESISTANCE
Rt
= 0.260 m2
K/W (9 mm version)
Rt
= 0.400 m2
K/W (14 mm version)
SIZE
Rolls of:
1.50 m x 50 m (h x L) = 75 m2
(9 mm version)
1.50 m x 25 m (h x L) = 37.5 m2
(14 mm version)
This product comes with a top adhesive profile to seal the
overlapping flaps
PACKAGING Single rolls
Product made of 5 mm or 10 mm Isolmant with the upper side
bonded to FIBTEC XT1 (screen-printed anti-tearing fibre) and the
lower side to FIBTEC XF1 (special needle-punched fibre produced
according to specifications conceived to provide a better noise
reduction).
> Conditions of use
Isolmant BiPlus is recommended for high impact sound insulations with floating screed. It is also suitable for
single layer application in which the direct installation of building plants on the resilient layer requires tear
resistance fleece to avoid damaging the insulating material. It needs at least a 6 cm (for BiPlus 9 mm) or 7 cm (for
BiPlus 14 mm) screeds. Screeds with lower thickness should be reinforced by means of a suitable metal mesh or
fibres. Attention must be paid in case of dry shake installation of ceramic tiles.
> Item specifications
The resilient layer is made of expanded closed-cell physically cross-linked polyethylene with the lower side
bonded to a special needle-punched fibre that is conceived to enhance the acoustic performance, and the upper
side to an anti-tearing fleece (Isolmant BiPlus type). This product should be installed with the screen-printed
fleece facing upwards. The product comes with adhesive overlapping flap. Density approx. 30 kg/m3
. Thickness
approx. 9 or 14 mm. Dynamic stiffness 11 MN/m3
or 9 MN/m3
respectively for 9 or 14 mm versions.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
14. Full technical specifications at www.isolmant.com14
> ISOLMANT SUPER BIPLUS
> To be positioned with the screen-printed fabric facing upwards.
THICKNESS Approx. 10 mm
IMPACT SOUND INSULATION ΔLw
= 34 dB Value calculated according to EN ISO 12354-2 and UNI/TR 11175
DYNAMIC STIFFNESS s’ = 10 MN/m3
THERMAL RESISTANCE Rt
= 0,231 m2
K/W
COMPRESSION CLASS CP 2
SIZE
Rolls of 1,00 m x 10 m (h x L) = 10 m2
Product without overlaps. After coupled, the sheets should be
sealed by means of Isolmant Nastro Telato or Isolmant Fascia
Nastro.
PACKAGING Single rolls
Product made of 5 mm Isolmant with the lower side bonded to
FIBTEC XF1-EL (high performance elastic needle-punched fibre)
and the upper side bonded to Isolmant TeloGomma (special
viscoelastic mass) which is coated with an anti-tearing TNT fleece.
> Conditions of use
Isolmant Super BiPlus ensures high levels of impact sound insulation for horizontal partitions. In particular, it is
conceived for light structures as wooden flooring. It also provides a high airborne insulation. It is recommended
for single or double layer floor installations. It needs a finishing screed of at least 5 cm.
> Item specifications
The resilient layer is made of expanded closed-cell physically cross-linked polyethylene bonded, on the lower
side, to an elastic needle-punched fibre that is conceived to enhance the acoustic performance and, special
viscoelastic EPDM rubber which is coated with a TNT fleece (type Isolmant Super BiPlus). Thickness approx. 10
mm. This product should be positioned with the rubber side facing upwards. Dynamic stiffness 10 MN/m3
.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
15. Full technical specifications at www.isolmant.com 15
> ISOLTILE
IsolTile is a low thickness undertile acoustic layer, designed to the
acoustic refurbishment of new or existing floor. This product can be
directly laid under ceramic or wooden flooring. IsolTile is made
of HD expanded polypropylene (77 kg/m3
), calendered-coated by
FIBTEC XP1 on both sides. FIBTEC XP1 is non-woven, embossed,
black polypropylene.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
THICKNESS Approx. 2 mm
IMPACT SOUND INSULATION ΔLw
= 16 dB Certified value
THERMAL CONDUCTIVITY λ = 0.037 W/mK
THERMAL RESISTANCE Rt
= 0.054 m2
K/W
EQUIVALENT AIR LAYER THICKNESS Sd
= 30 m
COMPRESSIVE STRENGTH
10% compressive deformation at 151 kPa
25% compressive deformation at 180 kPa
40% compressive deformation at 222 kPa
50% compressive deformation at 274 kPa
SIZE Rolls of: 1 m x 20 m = 20 m2
PACKAGING Single rolls with accessories (sealing tape and flanking strip)
ACCESSORIES
Sealing strip: h 7,5 cm x L 20 m
Flanking strip: h 3 cm x L 20 m
> Conditions of use
IsolTile can be installed directly on the existing flooring where acoustic bridges and flanking paths are critical in terms
of compliance with the standards in force. It ensures a significant improvement of impact sound insulation with ceramic
tiles and wooden flooring as well. It could be also installed on floating screed to enhance acoustic performances. IsolTile
uncouples the floor covering from the substrate and neutralizes tensions between the substrate and the tile covering.
Furthermore directly transfers the load impact on the tile covering to the substrate avoiding point load concentration and tile
cracking. These product installation does not modify the standard procedure to lay the flooring. Isoltile does not need any
special adhesive that could be selected referring to the installation surface and finishing type. For instance, IsolTile could be
laid by means of C2 class tiles adhesive or bi-component epoxypolyurethane glues for wooden flooring. This product is also
suitable for hot water underfloor heating. Check: Rt
(finishing + Isolmant layer) ≤ 0,15 m2
K/W in case of wooden flooring.
> Item specifications
IsolTile is a low thickness uncoupling membrane and an undertile resilient layer, designed to the acoustic retrofitting of
new or existing floor. It is made of closed-cell physically cross-linked polypropylene foam that is calendered-coated with
non-woven, embossed, screenprinted polypropylene (Isolmant IsolTile type). A removable adhesive layer is provided on the
bottom side of IsolTile AD. Thickness approx. 2 mm, density approx. 77 kg/m3
, thermal conductivity 0.037 W/mK, Sd = 30 m.
It ensures 16 dB reduction of impact sound noise as per EN-ISO 140-8.
16. Full technical specifications at www.isolmant.com16
> ISOLMANT FIBRA HD
u ENHANCED PERFORMANCES t
THICKNESS Approx. 10 mm
DENSITY Approx. 140 kg/m3
IMPACT SOUND INSULATION
DRY SCREED
ΔLw
= 22 dB Value calculated
33 mm thin system gypsum fibre board 23 mm (28 kg/m2
), 10 mm Isolmant Fibra HD,
standard concrete slab
IMPACT SOUND INSULATION
POURED SCREED
ΔLw
= 27 dB ValuecalculatedaccordingtoUNIENISO12354-2andUNI/TR11175
EFFECTIVE DYNAMIC s’ = 13 MN/m3
COMPRESSION CLASS CP 2
THERMAL CONDUCTIVITY λ = 0.032 W/mK
THERMAL RESISTANCE Rt
= 0.313 m2
K/W
SPECIFIC HEAT CAPACITY cP
= 1200 J/kgK
VAPOUR RESISTANCE μ = 3
SIZE Panels of 1.00 m x 1.20 m = 1.20 m2
PACKAGING Packs 15 panels (equal to 18 m2
)
Acoustic resilient panel, made of HD (140 kg/m3
) FIBTEC PHD,
70% recycled post-consumer material suitable for impact sound
insulation especially with dry screed system. Non-toxic, ecological,
with unlimited duration.
Isolmant Fibra HD provides credits for green buildings
certifications according to LEED or ITACA rating systems.
> Conditions of use
Isolmant Fibra HD is suitable for impact sound insulation. In particular, it is recommended for creating dry floating
screed made of gypsum fibre boards, fibre cement or wood base panels. Its thin thickness allows the installation
of systems with reduced height. If used for standard screed, made of sand and cement (minimum 5 cm thickness),
a protective PE film should be laid before installation. The screed should ensure adequate mechanical resistance
depending on the effective load and laying conditions (specifications given by screed supplier).
> Item specifications
Resilient panels made of HD polyester fibre FIBTEC PHD (140 kg/m3
), with high acoustic and thermal characteristics.
Product made of 70% recycled fibre from post-consumer material. Non-toxic, ecological, with unlimited duration.
Dynamic stiffness: s’ = 13 MN/m3
according to UNI EN 29052-1. Panel thermal resistance: Rt
= 0.313 m2
K/W.
Approx. 1.00 x 1.20 m panels.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
17. Full technical specifications at www.isolmant.com 17
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> ISOLMANT D311
THICKNESS Approx. 22 mm
THERMAL CONDUCTIVITY λ = 0.037 W/mK
THERMAL RESISTANCE Rt
= 0.595 m2
K/W
SPECIFIC HEAT CAPACITY c = 2100 J/kgK
VAPOUR RESISTANCE μ = 3600
EQUIVALENT AIR LAYER THICKNESS Sd
= 79 m
UNDER LOAD DEFLECTION 4.6% at 2 kPa
COMPRESSION CLASS CP 2
IMPACT SOUND INSULATION ΔLw
= 26 dB Value calculated according to UNI EN ISO 12354 and UNI/TR 11175
DYNAMIC STIFFNESS s’ = 37 MN/m3
SIZE
Panels of 1.0 m x 1.5 m = 1.5 m2
Once laid close, the panels should be sealed by means of Isolmant
Nastro Telato or Isolmant Fascia Nastro
PACKAGING Packs of 15 panels (equal to 22.5 m2
)
Product made of a double-layer Isolmant with the upper side
bonded to a high resistance aluminate embossed anti-tearing film.
To be installed with the aluminate-coated side facing upwards
> Conditions of use
Isolmant D311 is recommended for under screed installation in single layer applications. Its application ensures high
levels of thermal and impact sound insulation of the partition floor. It needs a finishing screed of at least 7 cm. The
screed should be suitably reinforced or reinforced by means of a suitable fibre. It is also raccomanded for acoustic and
thermal isolation on pilotis floor.
> Item specifications
The resilient layer is made of expanded closed-cell cross-linked polyethylene bonded to an embossed aluminatecoated
anti-tearing film (Isolmant D311 type). This product should be installed with the aluminate-coated side facing upwards.
Density approx. 30 kg/m3
. Thickness approx. 22 mm. Dynamic stiffness 37 MN/m3
.
18. Full technical specifications at www.isolmant.com18
> ISOLMANT FASCIA PERIMETRALE
STACCA/ATTACCA
THICKNESS Approx. 3 mm
FLANKING PATH NOISE REDUCTION
The non-use of Isolmant Fascia Perimetrale causes an acoustic
bridge and a consequent decibel loss
INSTALLATION
• Use this adhesive side to connect the strips to wall, floor or
insulating layer
• Trim the extra length only after laying and grouting tile flooring
and before installing the skirting boards
SIZE Strips of 15 cm x 100 m
PACKAGING 10 rolls equal to 1000 m
15 cm height adhesive strips made of 3 mm expanded closed-cell
cross-linked polyethylene with reusable adhesive side.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> Conditions of use
Isolmant Fascia Perimetrale avoids flanking noise and vibration transmission from floating screed to the partition
wall. To ensure the proper functioning of the floating floor it is necessary that the whole system resting on the
resilient layer can move freely. Flanking strips avoid any rigid contacts between screed and walls, pillars and
façades. It can substitute the elastic material used for expansion joints.
> Item specifications
Adhesive strip for the perimeter acoustic insulation made of expanded closed-cell cross-linked polyethylene with
approx. 30 density kg/m3
. Height 15 cm. It is provided in boxes of 10 elements of 100 m each. Thickness approx. 3 mm.
19. Full technical specifications at www.isolmant.com 19
> ISOLMANT FASCIA PERIMETRALE
TECNICA RETICOLATA
THICKNESS Approx. 5 mm
FLANKING PATH NOISE REDUCTION
The non-use of Isolmant Fascia Perimetrale causes an acoustic
bridge and a consequent decibel loss
INSTALLATION
• After removing the protection film of the adhesive side, Isolmant
Fascia Perimetrale can be installed on the floor (or the resilient
layer already positioned) and then to the wall
• The extra length could be trimmed with “snap-off blade” utility
knife after completing flooring installation and finishing
SIZE 18.5 - 25 cm x 50 m strips
PACKAGING
Version h 18.5 cm: 8 rolls equal to 400 m
Version h 25 cm: 6 rolls equal to 300 m
Expanded cross-linked closed-cell polyethylene strips designed for
easy installation. These strips come with a screen-printed side with
the installation instructions.
This product is available in three versions:
- h 18.5 cm (11 cm wall + 7.5 cm floor);
- h 25 cm (17.5 cm wall + 7.5 cm floor).
> Conditions of use
Isolmant Fascia Perimetrale avoids flanking noise and vibration transmission from floating screed to the partition wall.
To ensure the proper functioning of the floating floor it is necessary that the whole system resting on the resilient layer
can move freely. Flanking strips avoid any rigid contacts between screed and walls, pillars and façades. In addition,
as an alternative to turn up and bend the resilient layer along the edges of the floating screed (which is sometimes
difficult during installation), it is possible to apply Isolmant flanking strips along the room perimeter. It can substitute
the elastic material used for expansion joints. Designed for easy installation, this flanking strip ensures an high-level
of acoustic performance.
> Item specifications
Perimeter flanking strip made of expanded closed-cell cross-linked polyethylene with approx. 30 density kg/m3
. This
product is designed for easy installation. These strips come with a screen-printed side with installation instructions
(Isolmant Fascia Perimetrale Tecnica Reticoalta type). Height 18.5 cm or 25 cm, pack of 8 or 6 rolls of 50 m/each.
Thickness approx. 5 mm.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
20. Full technical specifications at www.isolmant.com20
> ISOLMANT FASCIA PERIMETRALE
TECNICA RADIANTE
THICKNESS 8 mm
FLANKING PATH NOISE REDUCTION
The non-use of Isolmant Fascia Perimetrale Radiante causes, a
thermal and acoustic bridge which can affect the acoustic and
thermal performances of the radiant panels system
INSTALLATION
• Use the replaceable adhesive side to connect the flanking strip to
the wall
• The strip should be very well connected to the acoustic resilient
layer
• Use the heating pipes to fix the polyethylene layer, which extends
from the strip, to the thermal panel
• Lay the thermal panel on the strip avoiding any physical gap in
which any concrete material could end
• Trim the extra length only after laying and grouting the tiles and
before installing the skirting boards
SIZE Strips of 15 cm x 25 m
PACKAGING 10 rolls equal to 250 m
Vertical flankinf strips made of expanded closed-cell cross-linked
polyethylene with 15 cm height designed for easy installation in
case of underfloor heating and cooling systems. These strips have a
reusable adhesive flap to overlap the castellated panel. In addition,
the strips are screen-printed with installation instructions. The
product should be used when Isolmant Radiante is istalled as a
resilient layer below a screed.
> Conditions of use
Isolmant Fascia Perimetrale Radiante avoids flanking noise and vibration transmission from floating screed to the
partition wall. The product is designed for easy installation in case of underfloor heating and cooling systems. To
ensure the proper functioning of the floating floor it is necessary that the whole system resting on the resilient layer
could move freely. Flanking strips avoid any rigid contacts between the screed and walls, pillars and façades. In case of
underfloor heating systems, Isolmant Fascia Perimetrale Radiante can be used as expansion joint and thermal break.
> Item specifications
Fascia Perimetrale Radiante is a flanking strip for the acoustic and thermal insulation of screed in case of underfloor
heating and cooling systems. The strip is made of expanded closed-cell cross-linked polyethylene with approx. 30 kg/m3
density. The product comes with a polyethylene flap to overlap the castellated underfloor insulation panels. Height 15 cm.
It is provided in boxes with 10 elements of 25 m each. Thickness approx. 8 mm.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
21. Full technical specifications at www.isolmant.com 21
THICKNESS Approx. 5 mm (vertical part) - approx. 0.1 mm (horizontal part)
FLANKING PATH NOISE REDUCTION
The non-use of Isolmant Fascia Perimetrale causes an acoustic
bridge and a consequent decibel loss
INSTALLATION
Isolmant Fascia Perimetrale Tecnica doppio spessore is suitable
for installation over the resilient layer due to its silicone adhesive
paper film on the bottom sides. Trim the extra length only after
laying and grouting tiles and before installing the skirting boards.
SIZE 28 cm x 50 m strips
PACKAGING 4 rolls equal to 200 m
> Conditions of use
Isolmant Fascia Perimetrale avoids flanking noise and vibration transmission from floating screed to the partition wall.
To ensure the proper functioning of the floating floor it is necessary that the whole system resting on the resilient layer
can move freely. Flanking strips avoid any rigid contacts between screed and walls, pillars and façades. In addition,
as an alternative to turn up and bend the resilient layer along the edges of the floating screed (which is sometimes
difficult during installation), it is possible to apply Isolmant flanking strips along the room perimeter. It can substitute
the elastic material used for expansion joints. Designed for easy installation, this flanking strip ensures an high-level
of acoustic performance.
> Item specifications
Adhesive double thickness perimeter strips designed for easy installation, which consist of a vertical side made of
expanded cross-linked polyethylene with 5 mm thickness. This side is partially adhesive and it is conceived to be
installed on the wall. The horizontal part is made of an HDPE film with 0.1 mm thickness and silicone adhesive paper
on the lower sides for installation over the resilient layer (Isolmant Fascia Perimetrale Tecnica Doppio Spessore type).
Height 28 cm high strips packed in 4 rolls box of 200 m each.
> ISOLMANT FASCIA PERIMETRALE
TECNICA DOPPIO SPESSORE
Adhesive perimeter strips designed for an easy installation. They
have a vertical part made of expanded cross-linked polyethylene
with 5 mm thickness. This side is partially adhesive and it is
conceived to be installed on the wall. The horizontal part is made of
an HDPE film with 0.1 mm thickness and silicone adhesive paper
on one sides. These strips come with a screen-printed side with
installation instructions.
This product is available: h 28 cm (18 cm wall + 10 cm floor);
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
22. Full technical specifications at www.isolmant.com22
> ISOLMANT FASCIA
PERIMETRALE 6.E
Flanking strips made of 6 mm Isolmant Strong (high density 70 kg/m3
expanded closed-cell physically crosslinked polyethylene) available
in two version:
- adhesive with tree different high 10, 15 and 30 cm
- not adhesive with tree different high 10, 15 and 30 cm
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
THICKNESS Approx. 6 mm
SIZE
strips h 10 cm by 50 m in length
strips h 15 cm by 50 m in length
strips h 30 cm by 50 m in length
(not adhesive and adhesive version)
PACKAGING
h 10 cm 15 strips = 750 m (1 roll)
h 15 cm 10 strips = 500 m (1 roll)
h 30 cm 5 strips = 250 m (1 roll)
minimum amount: at least 2 rolls of adhesive
product (different strip high can be chosen)
FLANKING
PATH NOISE
REDUCTION
The acoustic efficiency of floating floor with air cavity will be
adversely affected if acoustic bridging between the floating layer
and the surrounding structure should occur. When installed
around the floor perimeter eliminates acoustic flanking with the
wall and the treatments.
INSTALLATION
- Use adhesive or metal staplers to attach the strips to the wall
and to plinth base structures;
- Strips must be placed in the joint between the screed (wet or dry
laid) and the surrounding walls, trapped to the wall;
- Before pouring concrete screes, seal the joint between the
flanking strip and the Isolmant sheet
with Isolmant Nastro Telato;
- Cut off the excess part only after laying the flooring, before
applying the baseboard.
> Conditions of use
Flankin strips are essential when to prevent vibration transmission from floating floor to the partition wall or plinth
base structures. It is particularly recommended with floating floor with air cavity.
> Item specifications
Flanking strips made of 6 mm high density (70 kg/m3
) expanded closed-cell physically cross-linked polyethylene.
Available in adhesive and not adhesive versions with tree different high 10, 15 and 30 cm.
23. Full technical specifications at www.isolmant.com 23
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
> ISOLMANT FASCIA
PERIMETRALE 10.E
Flanking strips made of 10 mm high quality expanded closed-cell
cross-linked polyethylene available in two version:
- adhesive with four different high 10, 15, 20 and 30 cm
- not adhesive with four different high 10, 15, 20 and 30 cm
THICKNESS Approx. 10 mm
SIZE
strips h 10 cm by 60 m in length
strips h 15 cm by 60 m in length
strips h 20 cm by 60 m in length
strips h 30 cm by 60 m in length
(not adhesive and adhesive version)
PACKAGING
h 10 cm 12 strips = 720 m (1 roll)
h 15 cm 8 strips = 480 m (1 roll)
h 20 cm 6 strips = 360 m (1 roll)
h 30 cm 4 strips = 240 m (1 roll)
minimum amount: at least 2 rolls of adhesive
product (different strip high can be chosen)
FLANKING PATH NOISE REDUCTION
The acoustic efficiency of floating floor with air cavity will be
adversely affected if acoustic bridging between the floating layer
and the surrounding structure should occur. When installed
around the floor perimeter eliminates acoustic flanking with the
wall and the treatments.
INSTALLATION
- Use adhesive or metal staplers to attach the strips to the wall
and to plinth base structures;
- Strips must be placed in the joint between the screed (wet or dry
laid) and the surrounding walls, trapped to the wall;
- Before pouring concrete screes, seal the joint between the
flanking strip and the Isolmant sheet
with Isolmant Nastro Telato;
- Cut off the excess part only after laying the flooring, before
applying the baseboard.
> Conditions of use
Flankin strips are essential when to prevent vibration transmission from floating floor to the partition wall or plinth
base structures. It is particularly recommended with floating floor with air cavity.
> Item specifications
Flanking strips made of 10 mm expanded closedcell cross-linked polyethylene (30 kg/m3
). Available in adhesive and
not adhesive versions with four different high 10, 15, 20 and 30 cm.
24. Full technical specifications at www.isolmant.com24
> ISOLMANT FASCIA NASTRO
Adhesive strip made of 7.5 cm high Isolmant, suitable for sealing
together the sheets of Isolmant.
> Conditions of use
Ideal for sealing together the sheets of resilient under screed material (especially if they have no adhesive overlapping
flaps), thus preventing the passage of noise and humidity. Isolmant Fascia Nastro ensures the continuity of the resilient
materirial: all openings and joints should be suitably sealed to prevent screed material escaping expecailly in case of
self-compacting free flowing floor screed. It can be also useful to repair the insulating layer in case of damages.
> Item specifications
Adhesive sealing strip made of expanded closed-cell cross-linked polyethylene (approx. 30 kg/m3
) provided in rolls of
7.5 cm height. Thickness approx. 3 mm.
IMPACT SOUND INSULATION > UNDERSCREED INSULATION
THICKNESS Approx. 3 mm
IMPACT SOUND INSULATION
The non-use of Isolmant Fascia Nastro causes a decibel loss that
occurs when the Isolmant sheets are not properly sealed
INSTALLATION Install Isolmant Fascia Nastro after trimming it using a cutter
SIZE Strips of 7.5 cm x 50 m
PACKAGING 4 rolls equal to 200 m
25. Full technical specifications at www.isolmant.com 25
IMPACT SOUND INSULATION > STAIRCASE INSULATION
> ISOLMANT KIT SCALE
THICKNESS Approx. 2 mm
INSTALLATION
Check the surface that should be planar and moisturise the stair-
case concrete before laying the adhesive.
- Cut Isoltile sheets and install them by means of the C2 class
adhesive. Isolmant IsolTile should be installed also on the landings
between a flight of steps and the following one.
- Once installed Isolmant IsolTile, seal the sheets that have been
laid on each step by means of the IsolTile strip.
- Install Isolmant Isoltile lateral strip on the vertical partition to
disconnect the step and the staircase wall.
- By means of Isoltile sealing tape seal the connection line betwe-
en Isoltile lateral strip and Isolmant IsolTile that is installed on the
step and on the landing. Lay the mortar bed on the IsolTile sheet
installed on step and landing.
- Install the marble tile by means of mortar or adhesive. Cut the
extra length of IsolTile lateral strip after installing the flooring.
- Then lay the skirting boards sealing the clearance between the
base and the marble.
SIZE
Isolmant IsolTile treads sheet: h 33 for 125 cm
Isolmant IsolTile risers sheet: h 20 for 125 cm
Isolmant IsolTile landing sheet: h 50 for 125 cm
Isolmant IsolTile sealing tape: h 7.5 cm for 20 m
Isolmant IsolTile lateral strip: h 18.5 cm per 25 m
Isolmant Fascia Tagliabattiscopa: h 3 cm per 15 m
PACKAGING
Note: one Kit to insulate a standard stair-
case (two half-stairs and one landing).
Isolmant IsolTile treads sheet: 22 elements
Isolmant IsolTile risers sheet: 22 elements
Isolmant IsolTile landing sheet: 4 elements
Isolmant IsolTile sealing tape: 5 elements
Isolmant IsolTile lateral strip: 1 element
Isolmant Fascia Tagliabattiscopa: 2 element
IsolTile is a low thickness uncoupling membrane and an undertile
resilient layer, designed to the acoustic retrofitting of new or
existing floor. it is made of HD expanded polypropylene which is
calendered-coated by FIBTEC XP1 on both sides. FIBTEC-XP1 is
non-woven, embossed, screen-printed black polypropylene fibre,
designed for the acoustic insulation of finishings.
Isolmant Kit Scale comes with standards shapes sheets of IsolTile
that could be cut according to the actual size of treads and risers and
stairs landings. This kit includes all the necessary accessories as
adhesive tape to seal the sheet and flanking strips for disconnecting
wall and stairs both fundamental to perform the acoustic insulation
of stairs.
26. Full technical specifications at www.isolmant.com26
> ISOLMANT POLIMURO
AIRBORNE SOUND INSULATION > CAVITY WALL INSULATION
THICKNESS Approx. 12 mm
AIRBORNE SOUND INSULATION
Rw
= 54 dB Value certified
Cavity wall with 8 cm hollow brick and 12 cm poroton block (3 plasters)
Rw
= 54 dB Value certified
Cavity wall with 12 cm hollow brick and 12 cm poroton block (2 plasters)
THERMAL CONDUCTIVITY λ = 0.035 W/mK
VAPOUR RESISTANCE μ = 3600 (this value refers to the polyethylene layer)
EQUIVALENT AIR LAYER THICKNESS Sd
= 18 m
SPECIFIC HEAT CAPACITY c = 1450 J/kgK
SIZE
Rolls of 1.50 m x 25 m (h x L) = 37.5 m2
(Isolmant Polimuro ristrutturazione version)
Rolls of 1.50 m x 50 m (h x L) = 75 m2
Product with overlaps
PACKAGING Single rolls
Product made of 5 mm Isolmant with both sides bonded to FIBTEC
XF3 (special needle-punched fibre produced according to the
specifications designed to provide a better noise reduction).
> Conditions of use
Isolmant Polimuro is recommended for small cavities insulation (2 to 4 cm air gap). Soundproofing product that
enhances airborne sound insulation (internal anti-vibration element) and acts as a sound absorber of cavity resonan-
ce. Isolmant Polimuro should be fixed to the wall by means of nylon mechanical fasteners or by means of by a nailed
wooden batten on the top. Install Isolmant Polimuro by using the overlaps to get a uninterrupted layer, thus, it is pos-
sible to achieve a perfect acoustic insulation.
> Item specifications
Isolmant Polimuro is an unfaced roll made of expanded reticulated closed-cell polyethylene with both sides bonded to
a needle-punched fibre that is conceived to enhance the acoustic performance (Isolmant Polimuro type). Product with
overlaps. Density approx. 30 kg/m3
. Thickness approx. 12 mm.
27. Full technical specifications at www.isolmant.com 27
> ISOLMANT PERFETTO TR
AIRBORNE SOUND INSULATION > CAVITY WALL INSULATION
THICKNESS
Approx. 30 - 50 mm (stored)
Upon request (at least 500 m2
and within 20 working days in advance),it is also
possible to have products with no standard thickness and height
AIRBORNE SOUND INSULATION
Rw
= 58 dB Value certified
Cavity wall with 8 cm and 12 cm Poroton blocks (3 plasters) and Isolmant Perfetto
TR of 50 mm in the air gap
THERMAL CONDUCTIVITY λ = 0.035 W/mK
THERMAL RESISTANCE
Rt
= 0.858 m2
K/W (30 mm version)
Rt
= 1.429 m2
K/W (50 mm version)
SPECIFIC HEAT CAPACITY c = 1200 J/kgK
VAPOUR RESISTANCE μ = approx. 2
EQUIVALENT AIR LAYER THICKNESS Sd
= 0.06 - 0.10 m (30 and 50 mm versions respectively)
REACTION TO FIRE Euroclass B-s2,d0
SIZE
Panels of 1.00 m x 2.85 m = 2.85 m2
Upon request (at least 500 m2
and within 20 working days in advance), it is also
possible to have products with no standard thickness and height
PACKAGING
Packs of 10 - 7 panels (equal to 28.5 - 19.95 m2
each pack)
for 30 - 50 mm versions respectively
Insulating panel made of IsolFIBTEC PFT (recycled fibre of
polyester for technical application with increasing density along the
thickness). This fibre has high thermal and acoustic performance.
Non-toxic, ecological, with unlimited duration. Full height panel for
an easy installation. B-s2, d0 reaction to fire performance.
Isolmant Perfetto TR provides credits for green buildings
certifications according to LEED or ITACA rating systems.
> Conditions of use
Isolmant Perfetto TR is a versatile product. It is recommended for acoustic and thermal insulation cavity wall both
perimeter partition and between different dwelling units. Isolmant Perfetto TR can be dry laid between the two leaf
wall (if necessary it can be glued or screwed). No sealing is required between panels.
> Item specifications
Insulating layer made of big-size panels (1.00 x 2.85 m). The panels are made of recycled fibre of polyester for technical
application whose density increase along the thickness. These panels provide a high sound and thermal insulation
(type Isolmant Perfetto TR). Thickness 30 o 50 mm. Panel thermal resistance equal to 0.858 - 1.429 m2
K/W for 30 and
50 mm versions respectively. B-s2, d0 reaction to fire performance.
28. Full technical specifications at www.isolmant.com28
> ISOLMANT PERFETTO SPECIAL
AIRBORNE SOUND INSULATION > CAVITY WALL INSULATION
> To be positioned with the screen-printed side (logo Isolmant) in
visible position and facing the heated room.
THICKNESS Approx. 30 - 50 mm (stored)
AIRBORNE SOUND INSULATION
Rw
= 54 dB Value certified
Cavity wall with 8 cm and 12 cm hollow bricks (3 plasters) and Isolmant Perfetto
Specail of 30 mm in the air gap.
THERMAL CONDUCTIVITY
λ = 0.035 W/mK (this value refers to the IsolFIBTEC PFT panel)
λ = 0.035 W/mK (this value refers to Isolmant layer)
THERMAL RESISTANCE
Rt
= 0.858 m2
K/W (30 mm version)
Rt
= 1.429 m2
K/W (50 mm version)
SPECIFIC HEAT CAPACITY
c = 1200 J/kgK (30 mm version)
c = 1200 J/kgK (50 mm version)
VAPOUR RESISTANCE
μ = 3600 (this value refers to Isolmant Layer)
μ = 2 approx. (this value refers to IsolFIBTEC PFT panel)
EQUIVALENT AIR LAYER THICKNESS Sd
= 18 m
SIZE Panels of 1.00 m x 2.85 m = 2.85 m2
PACKAGING
Packs of 10 - 7 panels (equal to 28.5 - 19.95 m2
each pack)
for 30 - 50 mm versions respectively
Insulating panel made of IsolFIBTEC PFT (recycled fibre of
polyester for technical application with increasing density along
the thickness) bonded to 5 mm Isolmant Special. This fibre has
high thermal and acoustic performance, non-toxic, ecological, with
unlimited duration. Full height panel for an easy installation. This
product comes with overlaps.
Isolmant Perfetto BV provides credits for green buildings
certifications according to LEED or ITACA rating systems.
> Conditions of use
Isolmant Perfetto Special is a versatile product. It is recommended for acoustic and thermal insulation of cavity wall both
perimeter walls and partitions between different dwelling units. Isolmant Perfetto Special can be dry laid between the two
leaf wall (if necessary it can be glued or screwed).
> Item specifications
Insulating layer made of big-size panels (1.00 x 2.85 m). The panels are made of recycled polyester fibre with increasing
density along the thickness bonded to a layer of expanded closed-cell physically cross-linked polyethylene. This product
provides a high airborne and thermal insulation (Isolmant Perfetto Special type). Full height panel for an easy installation.
The product comes with overlaps. Thickness 30 o 50 mm approx. Panel thermal resistance equal to 0.857 m2
K/W or 1.429
m2
K/W for 30 and 50 mm versions respectively.
29. Full technical specifications at www.isolmant.com 29
> ISOLMANT FIBRA LC
AIRBORNE SOUND INSULATION > CAVITY WALL INSULATION
LCF I B R A
THICKNESS Approx. 40 - 60 - 80 mm
THERMAL CONDUCTIVITY λ = 0.039 W/mK
THERMAL RESISTANCE
Rt
= 1.026 m2
K/W (40 mm version)
Rt
= 1.538 m2
K/W (60 mm version)
Rt
= 2.052 m2
K/W (80 mm version)
SPECIFIC HEAT CAPACITY c = 1200 J/kgK
VAPOUR RESISTANCE μ = 2
EQUIVALENT AIR LAYER THICKNESS Sd
= 0.08 - 0.12 - 0.16 m (respectively for 40 - 60 - 80 mm versions)
AIRBORNE SOUND INSULATION Rw
> 50 dB
Cavity wall made of standard bricks without evident acoustic bridges
REACTION TO FIRE Class 1
SIZE Panels of 0.6 m x 1.50 m = 0.9 m2
PACKAGING
Packs of 30 - 20 - 15 panels (equal to 27 - 18 - 13,5 m2
each pack)
for 40 - 60 - 80 mm versions respectively
Insulating panel made of IsolFIBTEC FLC fibre (recycled and
thermo-bonded fibre of polyester for technical application). These
panels provide high sound and thermal performances/insulation.
Non-toxic, ecological, with unlimited duration.
IsolmantFibraLCprovidescreditsforgreenbuildingscertifications
according to LEED or ITACA rating systems.
> Conditions of use
Isolmant Fibra LC is a versatile product. It is recommended for acoustic and thermal insulation of masonry cavity
wall or drywall that are perimeter partition and between different dwelling units. Isolmant Fibra LC is conceived for
applications inside cavity walls that are made of standard blocks and without evident acoustic bridges, to provide a
better airborne sound insulation (higher than 50 dB).
> Item specifications
Insulating panel (0.6 x 1.50 m) made of recycled and thermo-bonded fibre of polyester. Reaction to fire class 1.
Thickness ... mm (40 - 60 - 80 mm).
30. Full technical specifications at www.isolmant.com30
> ISOLMANT FASCIA TAGLIAMURO
STANDARD/STRONG
AIRBORNE SOUND INSULATION > CAVITY WALL INSULATION
THICKNESS
Approx. 4 mm (Standard version)
Approx. 6 mm (Strong version)
FLANKING PATH NOISE REDUCTION
Enhance the impact sound insulation of the wall reducion flanking
transmission
MECHANICAL FEATURES
Standard 50 kg/m3
Strong 70 kg/m3
TENSILE STRENGTH:
Longitudinal: 675 kPa 835 kPa
Cross: 465 kPa 735 kPa
COMPRESSIVE STRENGTH:
10% compression: 30 kPa 85 kPa
25% compression: 55 kPa 115 kPa
50% compression: 125 kPa 185 kPa
COMPRESSION SET:
0,5 h. after discharge 16% 8%
25h. after discharge 7% 3%
22h. load, 23°C, compression at 25%
SIZE 10 - 15 - 30 cm x 50 m strips
PACKAGING
Version h 10 cm: 15 rolls equal to 750 m
Version h 15 cm: 10 rolls equal to 500 m
Version h 30 cm: 5 rolls equal to 250 m
10/15/30 cm underwall bearing strips made of HD Isolmant for
the acoustic insulation of hollow brick masonry. This product is
available as Standard (density approx. 50 kg/m3
, suitable for light
hollow brick masonry) and Strong version (density approx. 70 kg/m3
suitable for heavy hollow brick masonry).
> Conditions of use
Isolmant Fascia Tagliamuro is recommended to disconnect the vertical partitions, including the internal partition of
the perimeter wall to avoid rigid connections between the building elements. Thanks to its balanced density, Isolmant
Fascia Tagliamuro ensures the right mechanical strength (to avoid the cracking of partitions) and the anti-vibrations
isolation, which is necessary to avoid acoustic bridges.
> Item specifications
HD expanded closed-cell physically cross-linked polyethylene strips (Standard approx. 50 kg/m3
or Strong approx. 70
kg/ m3
) for the acoustic insulation of brick masonry with height 10/15/30 cm based to the masonry thickness. 4 mm
(Standard) or 6 mm thickness (Strong).
31. Full technical specifications at www.isolmant.com 31
> ISOLMANT PERFETTO CG
AIRBORNE SOUND INSULATION > FALSE WALL INSULATION
THICKNESS
Approx. 25 - 45 mm
Upon request (at least 500 m2
and within 20 working days in advance), it is also
possible to have products with no standard thickness and height
AIRBORNE SOUND INSULATION
Rw
= 55 dB Value certified
False wall with 8 cm hollow brick and metal structure, double plaster board
and 45 cm Perfetto CG in the cavity
THERMAL CONDUCTIVITY λ = 0.038 W/mK
THERMAL RESISTANCE
Rt
= 0.658 m2
K/W (25 mm version)
Rt
= 1.184 m2
K/W (45 mm version)
SPECIFIC HEAT CAPACITY c = 1200 J/kgK
VAPOUR RESISTANCE μ = 2
EQUIVALENT AIR LAYER THICKNESS Sd
= 0.05 - 0.09 m (25 and 45 mm versions respectively)
REACTION TO FIRE Euroclass B-s2,d0
SIZE Panels of 0.6 m x 1.00 m = 0.6 m2
PACKAGING
Packs of 30 - 20 panels (equal to 18 - 12 m2
each pack)
for 25 - 45 mm versions respectively
Insulating panel made of IsolFIBTEC PFT fibre (recycled fibre of
polyester for technical application with increasing density along
the thickness). These panels provide a high sound and thermal
insulation. Non-toxic, ecological, with unlimited duration.
Isolmant Perfetto CG provides credits for green building
certifications according to LEED or ITACA rating systems.
> Conditions of use
Isolmant Perfetto CG is a versatile product. It is recommended for acoustic and thermal insulation of light partition,
drywall, false ceiling and wall. It should be installed into stud spacing and it is suitable to fill partition cavity.
Isolmant Perfetto CG provides the partition with a high airborne insulation and a low thermal transmittance.
> Item specifications
Insulating panels (0.6 x 1.00 m) made of recycled fibre of polyester for technical application whose density increase
along the thickness. This product provides a high airborne insulation performance and thermal resistance as
well. (Isolmant Perfetto CG type). Thickness approx. 25 or 45 mm). Panel thermal resistance equal to respectively
0.658 - 1.184 m2
K/W for 25 and 45 mm versions.
32. Full technical specifications at www.isolmant.com32
> ISOLMANT NASTRO ORDITURA
CARTONGESSO
AIRBORNE SOUND INSULATION > FALSE WALL INSULATION
THICKNESS Approx. 3.5 mm
IMPACT SOUND INSULATION
In the event that Isolmant Nastro Orditura Cartongesso is not used
a decibel loss could be caused by rigid connections between metal
frame and adjoining building elements (wall and floor) and by
acoustic bridges between metal frame and plasterboard panels
INSTALLATION
The size of Isolmant Nastro Orditura Cartongesso should be
selected according to the web and flange depth size
SIZE
Length 30 m / width 30 - 50 - 70 - 95 mm (single adhesive side
version)
Length 20 m / width 30 - 50 - 75 - 100 mm (double adhesive side
version)
PACKAGING
30 - 18 - 12 - 10 rolls each paper box (single adhesive)
20 - 12 - 8 - 6 rolls each paper box (double adhesive)
Expanded cross-linked polyethylene strip to disconnect the metal
structure of the drywall. This accessory is available as single
adhesive side (width 30 - 50 - 70 and 95 mm) and double adhesive
as well (width 30 - 50 - 75 and 100 mm).
> Conditions of use
This product is suitable for disconnecting the metal structure of drywall or false wall from adjoining building elements
(wall and floor) and to reduce the acoustic bridge between metal frame and plasterboard panels. The strips should be
joined to webs and flanges of studs and runners.
> Item specifications
Expanded cross-linked polyethylene strip to disconnect the metal structure of drywalls. Width approx. 30 - 50 - 70
and 95 mm for the single adhesive version and width approx. 30 - 50 - 75 and 100 mm for the double adhesive version.
Thickness 3.5 mm. Density approx. 30 kg/m3
.
33. Full technical specifications at www.isolmant.com 33
> ISOLMANT TELOGOMMA
CASSONETTI
OUTDOOR SOUND INSULATION > ROLLING SHUTTER BOX INSULATION
THICKNESS Approx. 10 mm
AIRBORNE SOUND INSULATION Rw
= 26.5 dB Certified value
Window test on the TeloGomma and Isolmant
SIZE Rolls of 1 m x 10 m = 10 m2
PACKAGING 6 rolls pallet (equal to 60 m2
)
Product made of Isolmant Telogomma with the lower side bonded
to 3 mm Isolmant ant the upper side to 5 mm polyurethane for
sound absorption. The product has one side with adhesive.
> Conditions of use
Isolmant Telogomma Cassonetti is a visco-elastic mass product (special blend of EPDM rubber with mineral fillers)
with airborne sound insulation and sound absorbing characteristics. Due to the mass of Telogomma, the airborne
sound insulation increases, while the sound absorbing polyurethane improves the acoustic absorption and Isolmant
acts as a sound dampening element. These characteristics make Isolmant Telogomma Cassonetti suitable for isolating
windowshutter boxes. The sheets should be also fixed mechanically to ensure a long-term resistance as the adhesive
side is designed only for installation.
> Item specifications
Insulating material made a visco-elastic mass (special blend of EPDM rubber with mineral filler) with the lower side
bonded to 3 mm layer of expanded physically cross-linked polyethylene and the upper side to to a 5 mm polyurethane.
Total thickness approx. 10 mm. The product has one side with adhesive.
34. Full technical specifications at www.isolmant.com34
> ISOLMANT TELOGOMMA TUBI
THICKNESS Approx. 12 mm
AIRBORNE SOUND INSULATION
Rw
= 29 dB Certified value
Normal incidence sound transmission loss test with Telogomma of 4 kg/m2
THERMAL RESISTANCE Rt
= 0.293 m2
K/W
EQUIVALENT AIR LAYER THICKNESS Sd
= 50 m
SIZE
Rolls of 1 m x 3 m (h x L) = 3 m2
On request it is available with pre-cut every 20 cm
PACKAGING Single rolls
Flexible noise barrier made of special Isolmant Telogomma bonded
to 10 mm closed-cell expanded rubber combined with elastic polio-
lefinas. Product with one adhesive side.
>To be positioned with the rubber side facing upwards.
> Condition of use
Isolmant Telogomma Tubi is wrapped around the outside of duct or pipe to reduce the radiated noise. Provides high
performances as anti-vibration and anti-condensation system for the acoustic insualtion of ductwork or piping as air
or other contents move through it.
Thanks to its conformability and to the adhesive side the product can be easily applied on non-planar surfaces. It is
used to wrap noisy pipes, ducts, valves and fan housings.
Item specifications
Noise barrier made visco-elastic mass (special blend of EPDM rubber with mineral fillers) bonded to 10 mm closed-cell
expanded rubber combined with elastic poliolefinas. Product with one adhesive side. Total thickness approx. 12 mm.
EQUIPMENTS NOISE INSULATION > INSTALLATIONS NOISE INSULATION
35. Full technical specifications at www.isolmant.com 35
VISCO-ELASTIC MASS
> ISOLMANT TELOGOMMA
THICKNESS
Approx. 2 mm
Approx. 2.5 mm
WEIGHT
Approx. 4 kg/m2
(2 mm version)
Approx. 5 kg/m2
(2.5 mm version)
AIRBORNE SOUND INSULATION
Rw
= 29 dB Certified value (4kg/m2
version)
Normal incidence sound transmission loss test with rubber of 4 kg/m2
Rw
= 31 dB Certified value (5kg/m2
version)
Normal incidence sound transmission loss test of Telogomma 5 kg/m2
VAPOUR RESISTANCE μ = approx. 7000
SIZE Rolls of 1 m x 3 m (h x L) = 3 m2
PACKAGING 30 rolls pallet (equal to 90 m2
)
Visco-elastic mass made of a special blend of EPDM rubber with
mineral fillers (surface density 4 kg/m2
or 5 kg/m2
). This acoustic
membrane is coated on both sides with non-sticky non-woven
fabric. Isolmant Telogomma is recommended for the airborne
sound insulation and vibration isolation of drywalls, masonry walls,
plates, fibreglass, plastics and plywood. Upon request, it is possible
to have this product with one adhesive side.
> Conditions of use
Isolmant telogomma is a visco-elastic mass suitable for increasing the acoustic insulation of drywall, and as noise
barrier for the airborne sound insulation of plate roofs and, in general, as damping product for mechanical elements.
This flexible membrane can be used also on non-planar surfaces and it can be die cut and trimmed.
> Item specifications
Acoustic Insulating material made of EPDM polymer-based, mineral fillers, free bitumen and non-halogen rubber
with 2 mm thickness and surface density of 4 kg/m2
(or 2.5 mm thickness and density 5 kg/m2
) coated on both sides
with non-sticky non-woven fabric (Isolmant Telogomma type). Normal incidence sound transmission loss Rw
= 29 dB
for version 4 kg/m2
or Rw
= 31 dB for 5 kg/m2
version.
36. Full technical specifications at www.isolmant.com36
VISCO-ELASTIC MASS
> ISOLMANT TELOGOMMA E+45
THICKNESS Approx. 8 mm
WEIGHT 4 kg/m2
AIRBORNE SOUND INSULATION
Rw
= 29 dB Certified value
Normal incidence sound transmission loss test with rubber of 4 kg/m2
IMPACT SOUND INSULATION ΔLw
= 24 dB Certified value
SIZE Rolls of 1 m x 3 m (h x L) = 3 m2
PACKAGING Single roll
Product made of Isolmant Telogomma (visco-elastic mass approx. 4 kg/m2
)
with both sides bonded to Isolmant 3 mm.
Suitable for increasing sound insulation and vibration isolation of wood
structural floor.
> Conditions of use
Isolmant TeloGomma E+45 can increase the airborne and impact sound insulation of wood structural floor. This flexible
visco-elastic mass can be use on non-planar surfaces to wrap noisy pipes, air ducts, valves and fan housings.
> Item specifications
Acoustic Insulating material made of EPDM polymer-based, mineral fillers, free bitumen and non-halogen rubber
with 2 mm thickness and surface density of 4 kg/m2
with both sides bonded to 3 mm layer of expanded cross-linked
polyethylene (Isolmant TeloGomma E+45 type). Total thickness approx. 8 mm.
37. Full technical specifications at www.isolmant.com 37
VISCO-ELASTIC MASS
> ISOLMANT TELOGOMMA TT
THICKNESS Approx. 5.5 mm
WEIGHT Approx. 5 kg/m2
IMPACT SOUND INSULATION ΔLw
= 26.5 dB Certified value
DYNAMIC STIFFNESS s’ = 58 MN/m3
AIRBORNE SOUND INSULATION
Rw
= 26.5 dB Certified value
(Window test)
SIZE Rolls of 1 m x 3 m (h x L) = 3 m2
PACKAGING 20 rolls pallet (equal to 60 m2
)
Product made of Isolmant Telogomma (5 kg/m2
surface density) with
the lower side bonded to 3 mm Isolmant and the upper side coated
with non-sticky non-woven fabric. The product is recommended for
the airborne sound insulation and vibration isolation of light weight
floor or wall. Upon request, it is possible to have this product with
one adhesive side.
To be installed with the rubber side facing upwards (or visible in
wall applications).
> Conditions of use
Isolmant Telogomma TT is highly recommended as under screed sound-damping element in case of heavy loads
(like industrial equipment or bathrooms, lift shafts, thermal equipment room etc..). It is also suitable to disconnect
plasterboard panels in case of dry or false wall with metal structure. Suitable also for shower trays insualtion.
> Item specifications
Visco-elastic mass made of a special blend of EPDM rubber with mineral fillers (free bitumen and non-halogen rubber
with 2.5 mm thicknes) with the lower side bonded to 3 mm Isolmant and the upper side coated with non-sticky non-
woven fabric (Isolmant Telogomma TT type). Total thickness approx. 5.5 mm. 5 kg/m2
surface density.
Dynamic stiffness 58 MN/m3
.
38. Full technical specifications at www.isolmant.com38
SPECIAL PRODUCTS
> ISOLMANT CEMENTO ARMATO
THICKNESS Approx. 5 - 10 mm
THERMAL CONDUCTIVITY λ = 0.035 W/mK
VAPOUR RESISTANCE μ = 3600
EQUIVALENT AIR LAYER THICKNESS Sd
= 18 - 36 m (5 and 10 mm versions respectively)
INSTALLATION
Isolmant Cemento Armato has an adhesive side that makes this
product suitable to coat reinforced concrete structures as stair-
cases, lift-shafts and pillars. After wrapping the aforementioned
structures, it is recommended to install hollow tiles with plaster
finish of at least 4 cm or alternatively install the suitable mesh
(Nervometal type) to fix the plaster.
SIZE
1.50 m x 100 m (h x L) = 150 m2
(5 mm version)
1.20 m x 60 m (h x L) = 72 m2
(10 mm version)
PACKAGING Single rolls
Isolmant with an adhesive side. Its closed-cell structure provides
high and long-term acoustic and thermal insulation performances.
> Conditions of use
Isolmant Cemento Armato is suitable to insulate vertical reinforced concrete structures, in particular to carry out the
vibration isolation of structures such as staircases, lift shafts, pillars. The sheets should be also fixed mechanically to
ensure a long-term resistance as the adhesive side is designed only to position the material.
> Item specifications
Expanded cross-linked closed cell polyethylene with an adhesive side (Isolmant Cemento Armato type).
Density 30 kg/m3
. Thickness appro. 5 or 10 mm.
39. Full technical specifications at www.isolmant.com 39
SPECIAL PRODUCTS
> ISOLMANT DAMP
THICKNESS Approx. 5 - 10 - 20 mm
DENSITY Approx. 700 kg/m3
THERMAL CONDUCTIVITY λ = 0.11 W/mK
COMPRESSIVE STRENGTH Compressive deformation: 5% with 50 kPa, 10% with 100 kPa
SIZE
Rolls of 1 m x 10 m = 10 m2
(5 mm version)
Panels of 1 m x 1.20 m = 1.20 m2
(10 mm version)
Panels of 1 m x 1.20 m = 1.20 m2
(20 mm version)
PACKAGING
Single rolls equal to 15 - 10 m2
(for 5 mm version)
50-100 panels pallet equal to 120-60 m2
(respectively for 10-20 mm
versions)
Sound dampening element made of vulcanised granules rubber to
be installed under heavy loads.Density approx. 700 kg/m3
.
> Conditions of use
Isolmant Damp is a sound dampening product suitable for vibration isolation of horizontal structures to be installed
under heavy loads.
> Item specifications
Sound dampening and anti-vibration product made of agglomerate of SBR rubber granules to be installed under heavy
loads. (Isolmant Damp type). Thickness approx. 5 - 10 - 20 mm. Density approx. 700 kg/m3
.
40. Full technical specifications at www.isolmant.com40
SPECIAL PRODUCTS
> ISOLMANT STRONG
THICKNESS Approx. 6 mm
DENSITY Approx. 70 kg/m3
COMPRESSIVE STRENGTH
deformation 10%: 85 kPa
deformation 25%: 120 kPa
deformation 50%: 185 kPa
COMPRESSION SET
0,5 h after discharge, 23°C: 8%
24 h after discharge, 23°C: 3%
after 22 h load causing 25% deflection
THERMAL CONDUCTIVITY λ = 0.043 W/mK
THERMAL RESISTANCE Rt
= 0.140 m2
K/W
SPECIFIC HEAT CAPACITY c = 2100 J/kgK
VAPOUR RESISTANCE μ = 6700
EQUIVALENT AIR LAYER THICKNESS Sd
= 40 m
SIZE Rolls of 1.50 m x 50 m (h x L) = 75 m2
PACKAGING Single rolls
Acoustic resilient layer made of high-density Isolmant (approx.
70 kg/m3
). It is suitable for impact sound insulation and vibration
isolation in case of heavy loads.
> Conditions of use
Isolmant Strong is recommended for impact sound insulation and vibrations isolation in case of very heavy loads. In
non-residential structures, when live loads exceed 5 kN/m2
, it can be used also by overlapping some layers on each
other.
> Item specifications
The resilient layer is made of high density physically cross-linked polyethylene foam for impact sound insulation and
vibrations isolation with high compressive strength under heavy loads (live loads exceeding 5 kN/m2
) (Isolmant Strong
type). Thickness 6 mm, density 70 kg/m3
. 10% compressive deformation with 85 kPa. 3% residual deflection after 24 h
(after 22 h load causing 25% deflection).
41. WARNING
Although, these instructions are the result of our
best expertise they are indicative. The user should
establish whether the product is suitable for its
intended application. The user will be also in charge
ofalltheresponsibilityfortheuseoftheproductitself.
The technical information in this catalogue replaces
the previous one. Tecnasfalti reserves to change
without notice product size and packaging.
For further information, please refer to the website
www.isolmant.com
ATTENTION:
Do not expose to direct sun or severe weather
conditions.
Temperatures below 10° C could reduce the adhesive
properties of some products. Please, do not expose
the materials to lower temperatures except for the
installation (please refer to the icons on technical
specifications and packages). Do not use on cold
and / or humid surfaces since the presence of water
reduces irremediably the adhesive characteristics of
the product.
42.
43. for purchase orders, please contact:
ordini@isolmant.it
for commercial information:
clienti@isolmant.it
for technical information:
tecnico@isolmant.it
for general requests:
segreteria@isolmant.it
Follow us on