This document provides guidance on using bioswales, vegetative buffers, and constructed wetlands to treat stormwater runoff and remove pollutants. It discusses the soil, biological, and vegetation considerations for these natural systems. It then focuses on design principles for bioswales and constructed wetlands, including vegetation selection, slopes, dimensions, construction, water flow, and maintenance needs. Case studies of different applications in Oregon are also presented. The goal is to help others properly design, implement and maintain these green infrastructure practices to effectively improve water quality.
NH: Homeowner's Guide to Stormwater ManagementSotirakou964
This document provides a homeowner's guide to managing stormwater runoff from residential properties through low impact development techniques. It introduces the concept of stormwater and explains how traditional development can increase runoff and pollution. The guide then describes how low impact development practices like rain gardens and dry wells can help infiltrate and treat stormwater close to its source. It provides instructions for homeowners to estimate their property's stormwater runoff and footprint, test soils, and select appropriate locations for installing low impact development stormwater management practices.
MI: Michigan Technological University: Rain Garden Design and ConstructionSotirakou964
This document provides guidelines for designing and constructing rain gardens to capture rooftop runoff from homes. It defines rain gardens as shallow depressions in the soil that direct stormwater to maximize infiltration. The guidelines cover selecting appropriate sites, using suitable infiltration media and vegetation, properly sizing rain gardens, and maintaining them over time. The document aims to promote low impact development stormwater management techniques that minimize impacts on local hydrology.
OR: Portland: Downspout Disconnection Program - Putting Stormwater into Rain ...Sotirakou964
This document discusses downspout disconnection programs in multiple cities. It summarizes programs in Bremerton, Washington; Toronto, Canada; and Portland, Oregon. The Bremerton program educated residents about combined sewer overflows and facilitated separating private stormwater from sewers through site assessments, grants, and ordinances. Over 350 separations were completed, removing 260,000 gallons of stormwater annually. Toronto encourages disconnecting downspouts for free to reduce combined sewer overflows. Portland's program disconnects downspouts and redirects runoff onto lawns through incentives, volunteers, and contractors to reduce runoff and protect watersheds.
The document discusses the Bay-Friendly Gardening Program, which was developed to encourage environmentally friendly gardening choices that reduce waste and protect local watersheds. The program is run by the Alameda County Waste Management Authority and provides various resources to residents, such as workshops, tours, and training. It aims to educate the public on gardening practices that are sustainable and protect the San Francisco Bay.
Rainwater Tanks and Jars Construction Manual - Rainwater HarvestingSotirakou964
This document provides instructions for constructing cement rainwater jars and tanks. It discusses the materials needed, construction techniques, and installation of rainwater gutters. Rainwater collection is presented as a practical solution to water scarcity issues in rural and remote areas. The manual aims to promote rainwater harvesting at the household and community levels to improve access to safe water.
Los Angeles Rainwater Harvesting ManualSotirakou964
This document provides a homeowner's guide to harvesting rainwater in Los Angeles. It discusses the benefits of rainwater harvesting such as reducing pollution to local waterways, conserving water, and recharging groundwater. The guide describes various rainwater harvesting methods homeowners can implement, including redirecting downspouts to rain barrels or rain gardens. It provides step-by-step instructions for how to assess a site, measure slopes, and redirect downspouts. The guide also discusses plant selection and maintenance for rain gardens. Overall, the document aims to educate homeowners on simple rainwater harvesting techniques.
Texas water development board the manual texas on rainwater harvertingPlan Huerta
This chapter discusses the basic components of a rainwater harvesting system, including the catchment surface, gutters and downspouts, leaf screens, first-flush diverters, roof washers, storage tanks, pressure tanks and pumps, and treatment equipment. It focuses on residential or small-scale commercial systems for irrigation and potable water uses. The local health department and building codes should be consulted for system design and construction requirements.
Rainwater Harvesting for Multi Storied Apartments - Texas A&M Univseristy D7Z
The document discusses the historical background of rainwater harvesting as an ancient practice used worldwide to address water scarcity. It then reviews related literature on how rainwater harvesting has been used at the community level for domestic water supply and irrigation. The literature also examines how rainwater harvesting can help alleviate poverty and promote socioeconomic development.
NH: Homeowner's Guide to Stormwater ManagementSotirakou964
This document provides a homeowner's guide to managing stormwater runoff from residential properties through low impact development techniques. It introduces the concept of stormwater and explains how traditional development can increase runoff and pollution. The guide then describes how low impact development practices like rain gardens and dry wells can help infiltrate and treat stormwater close to its source. It provides instructions for homeowners to estimate their property's stormwater runoff and footprint, test soils, and select appropriate locations for installing low impact development stormwater management practices.
MI: Michigan Technological University: Rain Garden Design and ConstructionSotirakou964
This document provides guidelines for designing and constructing rain gardens to capture rooftop runoff from homes. It defines rain gardens as shallow depressions in the soil that direct stormwater to maximize infiltration. The guidelines cover selecting appropriate sites, using suitable infiltration media and vegetation, properly sizing rain gardens, and maintaining them over time. The document aims to promote low impact development stormwater management techniques that minimize impacts on local hydrology.
OR: Portland: Downspout Disconnection Program - Putting Stormwater into Rain ...Sotirakou964
This document discusses downspout disconnection programs in multiple cities. It summarizes programs in Bremerton, Washington; Toronto, Canada; and Portland, Oregon. The Bremerton program educated residents about combined sewer overflows and facilitated separating private stormwater from sewers through site assessments, grants, and ordinances. Over 350 separations were completed, removing 260,000 gallons of stormwater annually. Toronto encourages disconnecting downspouts for free to reduce combined sewer overflows. Portland's program disconnects downspouts and redirects runoff onto lawns through incentives, volunteers, and contractors to reduce runoff and protect watersheds.
The document discusses the Bay-Friendly Gardening Program, which was developed to encourage environmentally friendly gardening choices that reduce waste and protect local watersheds. The program is run by the Alameda County Waste Management Authority and provides various resources to residents, such as workshops, tours, and training. It aims to educate the public on gardening practices that are sustainable and protect the San Francisco Bay.
Rainwater Tanks and Jars Construction Manual - Rainwater HarvestingSotirakou964
This document provides instructions for constructing cement rainwater jars and tanks. It discusses the materials needed, construction techniques, and installation of rainwater gutters. Rainwater collection is presented as a practical solution to water scarcity issues in rural and remote areas. The manual aims to promote rainwater harvesting at the household and community levels to improve access to safe water.
Los Angeles Rainwater Harvesting ManualSotirakou964
This document provides a homeowner's guide to harvesting rainwater in Los Angeles. It discusses the benefits of rainwater harvesting such as reducing pollution to local waterways, conserving water, and recharging groundwater. The guide describes various rainwater harvesting methods homeowners can implement, including redirecting downspouts to rain barrels or rain gardens. It provides step-by-step instructions for how to assess a site, measure slopes, and redirect downspouts. The guide also discusses plant selection and maintenance for rain gardens. Overall, the document aims to educate homeowners on simple rainwater harvesting techniques.
Texas water development board the manual texas on rainwater harvertingPlan Huerta
This chapter discusses the basic components of a rainwater harvesting system, including the catchment surface, gutters and downspouts, leaf screens, first-flush diverters, roof washers, storage tanks, pressure tanks and pumps, and treatment equipment. It focuses on residential or small-scale commercial systems for irrigation and potable water uses. The local health department and building codes should be consulted for system design and construction requirements.
Rainwater Harvesting for Multi Storied Apartments - Texas A&M Univseristy D7Z
The document discusses the historical background of rainwater harvesting as an ancient practice used worldwide to address water scarcity. It then reviews related literature on how rainwater harvesting has been used at the community level for domestic water supply and irrigation. The literature also examines how rainwater harvesting can help alleviate poverty and promote socioeconomic development.
Rainwater Harvesting Retrofit Strategies: A Guide for Apartment Owners D7Z
This document provides an overview of retrofit strategies that can be implemented by apartment owners and managers to conserve water usage. It discusses both indoor and outdoor retrofit options, identifying strategies with quick paybacks such as installing low-flow showerheads and faucet aerators, as well as strategies involving utility rebates and programs. Outdoor strategies discussed include reducing lawn areas, installing efficient irrigation systems, and using native plants that require less water. The document provides context on typical water usage in apartments and the potential savings from various retrofit measures.
Easy Water-Wise Gardening - San Diego, CaliforniaRetiz16x
This document provides resources and advice for designing a water-conserving landscape, including:
- Speaking with landscape architects, contractors, designers, and irrigation consultants who can help design and install water-efficient landscapes.
- Checking local water district websites for plant recommendations, watering guidelines, and conservation tips.
- Viewing recommended websites that offer low-water landscape ideas, irrigation advice, and links to water agencies.
- Consulting local nurseries, which can offer plant selection and irrigation design assistance.
ME: Manual on Low Impact Development practices for CommunitiesSotirakou964
This document provides guidance for Maine communities on implementing Low Impact Development (LID) practices at the local level. It aims to help municipalities require basic stormwater management for small development projects using LID. The manual outlines LID standards for new single-family residential development, new non-residential and multifamily development, and retrofits to existing development. It also includes profiles of specific LID practices and example application forms communities can use for project review. The goal is to help communities address stormwater issues from small projects through low-cost and low-maintenance LID approaches.
This document provides information on creating a water-thrifty landscape through selecting plants adapted to local precipitation patterns, using alternatives to drinking water for irrigation such as rainwater collection, graywater, and air conditioning condensate, and employing efficient irrigation techniques. It discusses selecting drought-tolerant native plants, limiting lawn areas, using mulches to retain soil moisture, and harvesting rainwater through rain barrels or cisterns. The document recommends irrigating only when needed, using a rain gauge or soil moisture probe to determine when to water, and employing drip irrigation or soaker hoses to apply water slowly and directly to plant roots.
Florida Rain Gardens: Your Personal Contribution to Clean WaterSotirakou964
This document provides guidance for homeowners on designing and installing a rain garden. Rain gardens are landscaped areas planted with native plants that capture rainwater running off of roofs, driveways and other surfaces. They allow 30% more water to soak into the ground compared to a lawn, reducing stormwater runoff. Rain gardens provide multiple benefits, including recharging groundwater, reducing flooding, and filtering pollutants from rainwater before it reaches streams, lakes and other bodies of water. The document outlines the steps for siting, designing, building and maintaining a rain garden to help improve water quality and the environment.
Water Conservation Using Greywater - Clallam County, WashingtonFrida85y
This document provides information on water conservation and using greywater for irrigation. It defines greywater as wastewater from sinks, showers, and washing machines that can be used to irrigate landscapes. While greywater reduces fresh water use, it requires careful handling due to bacteria, viruses, and chemicals. The document recommends installing low-flow fixtures, repairing leaks, limiting showers, and choosing drought-resistant landscaping to conserve water. It outlines safely installing and using greywater systems through local permits, approved designs, and subsurface irrigation of ornamental plants.
This document introduces the need for a Green Communities Guide to help municipalities and developers address the challenges of rapid population growth and development in Alberta. Key issues identified through surveys include climate-related water shortages, deteriorating water quality, loss of wildlife habitat and fragmentation, and associated economic and social costs. The guide aims to provide tools and case studies to help communities develop strategies to conserve water, protect water quality, preserve agricultural land and open space, and maintain ecological services through more sustainable land use practices.
This document provides information about installing and using drip irrigation systems in the Mojave Desert. It discusses how drip irrigation works by slowly applying water directly to plant roots, allowing different amounts for different plant needs. Drip systems improve landscape quality, increase water efficiency by reducing waste, and are more suitable than sprinklers for the desert climate as they prevent water loss from evaporation and runoff. The document provides guidance on system components, design, installation, and maintenance to help homeowners create customized drip systems.
This document discusses borrow pits, waste, and their relevance to CLAD. [1] Borrow pits are excavated to obtain materials for wind farm construction and are preferably restored. [2] There is a question of whether restoring borrow pits with excavated materials constitutes waste disposal under the Waste Framework Directive. [3] The implications of classifying restoration as waste disposal are explored, and why demonstrating best practices for borrow pit restoration is important for CLAD.
H2O-Consult provides a range of technical advisory services relating to rainwater harvesting systems, including water audits, design services, and project management. The company was founded by Tony Cain, a civil engineer with over 20 years experience in water management. H2O-Consult can assess the feasibility of, design, and implement rainwater harvesting systems to reduce water consumption and costs for businesses, organizations, and individuals through the collection and storage of rainwater for non-potable uses.
Albuquerque, New Mexico Rainwater Harvesting ManualD6Z
This document provides a guide for rainwater harvesting systems in Albuquerque, New Mexico. It discusses simple rainwater harvesting systems that consist of a catchment area, distribution system, and landscape holding area. The guide describes how to design and construct simple systems, including using roofing as a catchment, gutters and downspouts as a distribution system, and depressed planting beds as holding areas. It emphasizes using native and drought-tolerant plants suited to intermittent water supplies.
Waterfall, patricia h. (universidad de arizona) harvesting rainwaterPlan Huerta
This document provides guidance on harvesting rainwater for landscape use. It discusses the components of a rainwater harvesting system, including the water supply (rainfall), plant water demands, and the system to move water. Simple systems can direct roof runoff to landscaped areas using gutters, downspouts and berms. Proper plant selection and constructing basins and swales can maximize water storage and direct runoff. Regular maintenance is needed to keep the system functioning well.
This document discusses rainwater harvesting policies and regulations. It begins by outlining the benefits of rainwater harvesting, which include providing an inexpensive water supply, augmenting drinking water supplies, reducing stormwater runoff and pollution, and reducing peak summer water demands. However, rainwater harvesting is not widely addressed by regulations and codes. The document then examines typical domestic and commercial water usage and how rainwater could be used more appropriately for non-potable uses like irrigation and toilet flushing. Key considerations for developing rainwater harvesting policies and regulations include appropriate water quality standards and treatment requirements to prevent cross-contamination based on end uses. Jurisdictions vary in their rules, with some allowing potable reuse and others limiting reuse to
Roof Top Gardens - LOW IMPACT DEVELOPMENT for BIG BOX RETAILERSFarrah85p
This document provides guidance on incorporating low impact development (LID) strategies and techniques into site designs for big box retailers. It discusses LID background and opportunities for big box sites. Ten initial LID best management practices are described, including bioretention basins, cells, and slopes, bioretention swales, cisterns/rain barrels, water quality swales, permeable/porous pavement, planter boxes, tree box filters, and green roofs. Case studies and fact sheets provide more details on implementing these practices. The goal is to help large retailers integrate LID to meet stormwater requirements while considering design, cost, and maintenance factors.
A presentation about reducing nutrients from stormwater runoff through low-impact development/green infrastructure techniques. Presented by Rich Claytor, engineer with Horsley Witten Group, during the Buzzards Bay Coalition's 2013 Decision Makers Workshop series. Learn more at www.savebuzzardsbay.org/DecisionMakers
This document provides information on how to establish and plant a rain garden. It recommends locating a rain garden to intercept runoff from impervious surfaces while avoiding poorly drained sites. When planting, use potted or bare root plants and space them based on their mature size. Contact local conservation agencies and greenhouses for more details on designing, building, and maintaining a rain garden.
Rain gardens for home drainage help, david dods, 06 09-12Jessi Veach
This document provides information on how to construct a rain garden to help manage home drainage. It discusses locating and sizing rain gardens, preparing the soil, selecting plants based on moisture and sun preferences, and installation details. The document emphasizes that rain gardens are shallow landscaped areas designed to soak up rainwater runoff from roofs, driveways, and other hard surfaces to prevent flooding and pollution while providing habitat. Proper construction and plant selection based on soil and moisture conditions are emphasized to ensure the water soaks into the ground within a day.
BioFilters for Pollution Removal from Storm Water - Manual ~ State of Oregon
`
For more information, Please see websites below:
`
Organic Edible Schoolyards & Gardening with Children =
http://scribd.com/doc/239851214 ~
`
Double Food Production from your School Garden with Organic Tech =
http://scribd.com/doc/239851079 ~
`
Free School Gardening Art Posters =
http://scribd.com/doc/239851159 ~
`
Increase Food Production with Companion Planting in your School Garden =
http://scribd.com/doc/239851159 ~
`
Healthy Foods Dramatically Improves Student Academic Success =
http://scribd.com/doc/239851348 ~
`
City Chickens for your Organic School Garden =
http://scribd.com/doc/239850440 ~
`
Simple Square Foot Gardening for Schools - Teacher Guide =
http://scribd.com/doc/239851110 ~
Water Sensitive Urban Design Vegetation Selection Guide - Darwin, AustraliaKaila694m
This document provides a vegetation selection guide for water sensitive urban design (WSUD) elements in the Darwin region, such as bioretention systems, wetlands, and grass swales/buffer strips. It includes indicative species lists of native Australian plants suited to these WSUD treatments. The species are adapted to wet-dry tropical conditions and sandy, free-draining soils. The guide is intended to assist practitioners in selecting appropriate vegetation to perform important functions like pollution filtration and habitat provision, while withstanding prolonged dry periods.
Rainwater harvesting participant with appendices 2011-11rsd kol abundjani
This document provides information about household rainwater harvesting systems. It is produced by CAWST, a non-profit organization focused on providing clean water and sanitation education. The document contains details on the history, benefits, and components of rainwater harvesting systems, including catchment areas, delivery systems, and storage reservoirs for both roof and ground catchment designs. It is intended to increase knowledge about rainwater harvesting technologies.
Rainwater Harvesting Retrofit Strategies: A Guide for Apartment Owners D7Z
This document provides an overview of retrofit strategies that can be implemented by apartment owners and managers to conserve water usage. It discusses both indoor and outdoor retrofit options, identifying strategies with quick paybacks such as installing low-flow showerheads and faucet aerators, as well as strategies involving utility rebates and programs. Outdoor strategies discussed include reducing lawn areas, installing efficient irrigation systems, and using native plants that require less water. The document provides context on typical water usage in apartments and the potential savings from various retrofit measures.
Easy Water-Wise Gardening - San Diego, CaliforniaRetiz16x
This document provides resources and advice for designing a water-conserving landscape, including:
- Speaking with landscape architects, contractors, designers, and irrigation consultants who can help design and install water-efficient landscapes.
- Checking local water district websites for plant recommendations, watering guidelines, and conservation tips.
- Viewing recommended websites that offer low-water landscape ideas, irrigation advice, and links to water agencies.
- Consulting local nurseries, which can offer plant selection and irrigation design assistance.
ME: Manual on Low Impact Development practices for CommunitiesSotirakou964
This document provides guidance for Maine communities on implementing Low Impact Development (LID) practices at the local level. It aims to help municipalities require basic stormwater management for small development projects using LID. The manual outlines LID standards for new single-family residential development, new non-residential and multifamily development, and retrofits to existing development. It also includes profiles of specific LID practices and example application forms communities can use for project review. The goal is to help communities address stormwater issues from small projects through low-cost and low-maintenance LID approaches.
This document provides information on creating a water-thrifty landscape through selecting plants adapted to local precipitation patterns, using alternatives to drinking water for irrigation such as rainwater collection, graywater, and air conditioning condensate, and employing efficient irrigation techniques. It discusses selecting drought-tolerant native plants, limiting lawn areas, using mulches to retain soil moisture, and harvesting rainwater through rain barrels or cisterns. The document recommends irrigating only when needed, using a rain gauge or soil moisture probe to determine when to water, and employing drip irrigation or soaker hoses to apply water slowly and directly to plant roots.
Florida Rain Gardens: Your Personal Contribution to Clean WaterSotirakou964
This document provides guidance for homeowners on designing and installing a rain garden. Rain gardens are landscaped areas planted with native plants that capture rainwater running off of roofs, driveways and other surfaces. They allow 30% more water to soak into the ground compared to a lawn, reducing stormwater runoff. Rain gardens provide multiple benefits, including recharging groundwater, reducing flooding, and filtering pollutants from rainwater before it reaches streams, lakes and other bodies of water. The document outlines the steps for siting, designing, building and maintaining a rain garden to help improve water quality and the environment.
Water Conservation Using Greywater - Clallam County, WashingtonFrida85y
This document provides information on water conservation and using greywater for irrigation. It defines greywater as wastewater from sinks, showers, and washing machines that can be used to irrigate landscapes. While greywater reduces fresh water use, it requires careful handling due to bacteria, viruses, and chemicals. The document recommends installing low-flow fixtures, repairing leaks, limiting showers, and choosing drought-resistant landscaping to conserve water. It outlines safely installing and using greywater systems through local permits, approved designs, and subsurface irrigation of ornamental plants.
This document introduces the need for a Green Communities Guide to help municipalities and developers address the challenges of rapid population growth and development in Alberta. Key issues identified through surveys include climate-related water shortages, deteriorating water quality, loss of wildlife habitat and fragmentation, and associated economic and social costs. The guide aims to provide tools and case studies to help communities develop strategies to conserve water, protect water quality, preserve agricultural land and open space, and maintain ecological services through more sustainable land use practices.
This document provides information about installing and using drip irrigation systems in the Mojave Desert. It discusses how drip irrigation works by slowly applying water directly to plant roots, allowing different amounts for different plant needs. Drip systems improve landscape quality, increase water efficiency by reducing waste, and are more suitable than sprinklers for the desert climate as they prevent water loss from evaporation and runoff. The document provides guidance on system components, design, installation, and maintenance to help homeowners create customized drip systems.
This document discusses borrow pits, waste, and their relevance to CLAD. [1] Borrow pits are excavated to obtain materials for wind farm construction and are preferably restored. [2] There is a question of whether restoring borrow pits with excavated materials constitutes waste disposal under the Waste Framework Directive. [3] The implications of classifying restoration as waste disposal are explored, and why demonstrating best practices for borrow pit restoration is important for CLAD.
H2O-Consult provides a range of technical advisory services relating to rainwater harvesting systems, including water audits, design services, and project management. The company was founded by Tony Cain, a civil engineer with over 20 years experience in water management. H2O-Consult can assess the feasibility of, design, and implement rainwater harvesting systems to reduce water consumption and costs for businesses, organizations, and individuals through the collection and storage of rainwater for non-potable uses.
Albuquerque, New Mexico Rainwater Harvesting ManualD6Z
This document provides a guide for rainwater harvesting systems in Albuquerque, New Mexico. It discusses simple rainwater harvesting systems that consist of a catchment area, distribution system, and landscape holding area. The guide describes how to design and construct simple systems, including using roofing as a catchment, gutters and downspouts as a distribution system, and depressed planting beds as holding areas. It emphasizes using native and drought-tolerant plants suited to intermittent water supplies.
Waterfall, patricia h. (universidad de arizona) harvesting rainwaterPlan Huerta
This document provides guidance on harvesting rainwater for landscape use. It discusses the components of a rainwater harvesting system, including the water supply (rainfall), plant water demands, and the system to move water. Simple systems can direct roof runoff to landscaped areas using gutters, downspouts and berms. Proper plant selection and constructing basins and swales can maximize water storage and direct runoff. Regular maintenance is needed to keep the system functioning well.
This document discusses rainwater harvesting policies and regulations. It begins by outlining the benefits of rainwater harvesting, which include providing an inexpensive water supply, augmenting drinking water supplies, reducing stormwater runoff and pollution, and reducing peak summer water demands. However, rainwater harvesting is not widely addressed by regulations and codes. The document then examines typical domestic and commercial water usage and how rainwater could be used more appropriately for non-potable uses like irrigation and toilet flushing. Key considerations for developing rainwater harvesting policies and regulations include appropriate water quality standards and treatment requirements to prevent cross-contamination based on end uses. Jurisdictions vary in their rules, with some allowing potable reuse and others limiting reuse to
Roof Top Gardens - LOW IMPACT DEVELOPMENT for BIG BOX RETAILERSFarrah85p
This document provides guidance on incorporating low impact development (LID) strategies and techniques into site designs for big box retailers. It discusses LID background and opportunities for big box sites. Ten initial LID best management practices are described, including bioretention basins, cells, and slopes, bioretention swales, cisterns/rain barrels, water quality swales, permeable/porous pavement, planter boxes, tree box filters, and green roofs. Case studies and fact sheets provide more details on implementing these practices. The goal is to help large retailers integrate LID to meet stormwater requirements while considering design, cost, and maintenance factors.
A presentation about reducing nutrients from stormwater runoff through low-impact development/green infrastructure techniques. Presented by Rich Claytor, engineer with Horsley Witten Group, during the Buzzards Bay Coalition's 2013 Decision Makers Workshop series. Learn more at www.savebuzzardsbay.org/DecisionMakers
This document provides information on how to establish and plant a rain garden. It recommends locating a rain garden to intercept runoff from impervious surfaces while avoiding poorly drained sites. When planting, use potted or bare root plants and space them based on their mature size. Contact local conservation agencies and greenhouses for more details on designing, building, and maintaining a rain garden.
Rain gardens for home drainage help, david dods, 06 09-12Jessi Veach
This document provides information on how to construct a rain garden to help manage home drainage. It discusses locating and sizing rain gardens, preparing the soil, selecting plants based on moisture and sun preferences, and installation details. The document emphasizes that rain gardens are shallow landscaped areas designed to soak up rainwater runoff from roofs, driveways, and other hard surfaces to prevent flooding and pollution while providing habitat. Proper construction and plant selection based on soil and moisture conditions are emphasized to ensure the water soaks into the ground within a day.
BioFilters for Pollution Removal from Storm Water - Manual ~ State of Oregon
`
For more information, Please see websites below:
`
Organic Edible Schoolyards & Gardening with Children =
http://scribd.com/doc/239851214 ~
`
Double Food Production from your School Garden with Organic Tech =
http://scribd.com/doc/239851079 ~
`
Free School Gardening Art Posters =
http://scribd.com/doc/239851159 ~
`
Increase Food Production with Companion Planting in your School Garden =
http://scribd.com/doc/239851159 ~
`
Healthy Foods Dramatically Improves Student Academic Success =
http://scribd.com/doc/239851348 ~
`
City Chickens for your Organic School Garden =
http://scribd.com/doc/239850440 ~
`
Simple Square Foot Gardening for Schools - Teacher Guide =
http://scribd.com/doc/239851110 ~
Water Sensitive Urban Design Vegetation Selection Guide - Darwin, AustraliaKaila694m
This document provides a vegetation selection guide for water sensitive urban design (WSUD) elements in the Darwin region, such as bioretention systems, wetlands, and grass swales/buffer strips. It includes indicative species lists of native Australian plants suited to these WSUD treatments. The species are adapted to wet-dry tropical conditions and sandy, free-draining soils. The guide is intended to assist practitioners in selecting appropriate vegetation to perform important functions like pollution filtration and habitat provision, while withstanding prolonged dry periods.
Rainwater harvesting participant with appendices 2011-11rsd kol abundjani
This document provides information about household rainwater harvesting systems. It is produced by CAWST, a non-profit organization focused on providing clean water and sanitation education. The document contains details on the history, benefits, and components of rainwater harvesting systems, including catchment areas, delivery systems, and storage reservoirs for both roof and ground catchment designs. It is intended to increase knowledge about rainwater harvesting technologies.
AK: Green Infrastructure Resource Guide for FairbanksSotirakou964
This document provides a Green Infrastructure Resource Guide for homeowners in Fairbanks, Alaska. It was developed through a partnership between local organizations to help mitigate stormwater runoff concerns. The guide discusses green infrastructure design considerations for Fairbanks' climate and geology. It also describes the process used to research and design appropriate best management practices, complete demonstration projects, and compile the guide. Ten selected BMPs are then described in detail, including rain barrels, rain gardens, tree pits, infiltration planters, dry wells, swales, green roofs, permeable pavers, grass reinforcement mesh, and riparian buffers.
This document provides an overview of the book "Drip Irrigation" by Samuel Dasberg and Dani Or. The book covers topics related to drip irrigation system components, soil water and salt modeling, system design considerations, monitoring and management, and practical applications. It aims to bridge knowledge across different disciplines involved in drip irrigation, including soil physics, agronomy, hydraulics engineering, and system design. The book provides information on emitters, laterals, main lines, filters, fertilizing systems, automation, modeling of soil water and solute movement, effects of variability, filtration and fertigation design, monitoring methods, and case studies of drip irrigation applications in various crops.
Maryland - Rain Gardens across Maryland: Cleaning Maryland’s Waterways One Rain Garden at a Time
`
For more information, Please see websites below:
`
Organic Edible Schoolyards & Gardening with Children =
http://scribd.com/doc/239851214 ~
`
Double Food Production from your School Garden with Organic Tech =
http://scribd.com/doc/239851079 ~
`
Free School Gardening Art Posters =
http://scribd.com/doc/239851159 ~
`
Increase Food Production with Companion Planting in your School Garden =
http://scribd.com/doc/239851159 ~
`
Healthy Foods Dramatically Improves Student Academic Success =
http://scribd.com/doc/239851348 ~
`
City Chickens for your Organic School Garden =
http://scribd.com/doc/239850440 ~
`
Simple Square Foot Gardening for Schools - Teacher Guide =
http://scribd.com/doc/239851110 ~
The report provides a preliminary design for a wastewater collection and treatment system for the town of Bahía Ballena, Costa Rica. The town currently has a population of 1,000 people that is projected to grow to 3,000-4,000 people within 10 years. Three potential sites for the wastewater treatment facility were evaluated. Site 3 was selected as it allows for gravity flow of wastewater through most of the system, has room for expansion, and is easily acquired. The designed collection system relies on gravity and costs $750,000. The treatment facility is capable of reducing wastewater to below effluent standards and costs $250,000 initially with $50,000 annual operating costs.
SUSTAINABLE REGENERATION OF URBAN GREEN AREAS IN EGYPT’S DESERT CITIES - Adop...Mahmoud Moursy Hussein
The existing employed planning and design approach of urban green spaces considering
the non-sustainable use of water resources and the lack of water reuse strategies can be
severely detrimental to the environment and human population. Green space elements
ranging from larger woodlands and public parks to private gardens, golf courses,
and green roofs, should be integrated with sustainable strategies such as stormwater
management, wastewater & greywater reuse, in order to overcome the raising urban
and environmental challenges. Simultaneously, to offer a solution to the chronic technical
problems of wastewater management in remote desert cities
This study aims to analyze and investigate current characteristics of planning and
management of green areas in Egypt’s new desert city, assessing the challenges and
shading the light on the potential of adopting green infrastructure strategies; identify the
areas of deficiency and develop a comprehensive vision and optimized scheme for the
development of the green areas in new desert cities.
Chapter 6 Running Case Assignment Improving Decision MakingWilheminaRossi174
Chapter 6 Running Case Assignment: Improving Decision Making:
Redesigning the Customer Database
Software skills: Database design; querying and reporting
Business skills: Customer profiling
Dirt Bikes U.S.A. sells primarily through its distributors. It maintains a
small customer database with the following data: customer name, address
(street, city, state, zip code), telephone number, model purchased, date of
purchase, and distributor. These data are collected by its distributors when
they make a sale and are then forwarded to Dirt Bikes. Dirt Bikes would like
to be able to market more aggressively to its customers.
The Marketing Department would like to be able to send customers e-
mail notices of special racing events and of sales on parts. It would also like
to learn more about customers’ interests and tastes: their ages, years of
schooling, another sport in which they are interested, and whether they
attend dirt bike racing events. Additionally, Dirt Bikes would like to know
whether customers own more than one motorcycle. (Some Dirt Bikes
customers own two or three motorcycles purchased from Dirt Bikes U.S.A.
or other manufacturer.) If a motorcycle was purchased from Dirt Bikes, the
company would like to know the date of purchase, model purchased, and
distributor. If the customer owns a non–Dirt Bikes motorcycle, the company
would like to know the manufacturer and model of the other motorcycle (or
motorcycles) and the distributor from whom the customer purchased that
motorcycle. Dirt Bikes’s customer database was redesigned so that it can
store and provide the information needed for marketing.
Case Questions:
Develop the following queries and reports that would be of great interest to
Dirt Bikes’s marketing and sales department.
1- Create a report of customers and motorcycles model grouped by
manufacturer.
2- Create a query about Dirt Bikes customers who attend racing events.
3- Create a query of the customers who have more than 12 years of
education.
Part 1
This is an individual assignment. Read the recent research article "Biochar Wastewater Treatment 2020." Prepare a 2-3 paragraph response for the following:
What are the main points of the article? How can it connect to scouring wool washing discussions for the wool industry? How can this technique be used more broadly in the apparel industry? Refer to the book Raw Material and Sustainability & Social Change in Fashion to develop your response. Provide key citations in APA format.
Part 2
After reading Raw Material Ch. 11- 15 (p. 138- 213), what are the main points that resonated with you? How does this connect with broader discussions about sustainable fashion in the book Sustainability & Social Change in Fashion?
lable at ScienceDirect
Chemosphere 252 (2020) 126539
Contents lists avai
Chemosphere
journal homepage: www.elsevier.com/locate/chemosphere
Review
Biochar technology in wastewater treatme ...
EPA -- Vapor Intrusion Considerations For Brownfields RedevelopmentHarryONeill
This primer is designed for land revitalization stakeholders concerned about vapor intrusion, including property owners, municipalities, and real estate developers. It provides an overview of the vapor intrusion issue and how it can affect redevelopment. It also summarizes techniques for quickly and cost effectively assessing the potential for vapor intrusion, as well as techniques for mitigating it.
This document provides an overview of vapor intrusion considerations for brownfield site redevelopment. It discusses what vapor intrusion is, why it is a concern, and how it can impact redevelopment. The document also summarizes techniques for assessing the potential for vapor intrusion and mitigating it, including passive and active methods. Key guidance documents and state resources on vapor intrusion are also referenced. The intended audience is land revitalization stakeholders concerned about addressing vapor intrusion in their redevelopment projects.
This document provides a step-by-step guide to designing and constructing a rain garden to help reduce stormwater runoff and promote groundwater recharge. It details the 7 steps to build a rain garden: 1) observe and map your site; 2) determine the location; 3) assess the soil; 4) determine the size; 5) construct it; 6) choose appropriate plants; and 7) maintenance. Sample rain garden layouts and plant lists tailored to Oregon's climate zones are also included to help homeowners design effective rain gardens. The guide aims to teach landscaping techniques that protect water quality and stream health.
The document provides a step-by-step guide to building a rain garden. It begins with observing and mapping the site to determine how water flows and where to locate the garden. Next, it discusses assessing the soil by testing infiltration and texture. It then covers determining the size of the garden based on the area draining to it. The guide also includes instructions for constructing the garden, including excavating, grading, and installing drainage. It concludes with recommendations for planting suitable species, mulching, and maintaining the garden. The overall goal is to help homeowners landscape to reduce stormwater runoff and pollution entering local waterways.
The guidelines describe the best practices
needed to construct, amend and maintain turf sporting fields and open space areas within the
Lower Hunter, Australia
This document provides guidance on sequencing batch reactor (SBR) design and operation. It was developed by the New England Interstate Water Pollution Control Commission based on a literature review and visits to five SBR facilities. The document aims to highlight design and operational enhancements that can improve wastewater treatment performance. It is intended to assist municipalities, engineers, regulators and operators working with SBR systems.
This document provides a summary of the Erosion and Sedimentation Manual published by the U.S. Department of the Interior Bureau of Reclamation in November 2006. The manual contains 7 chapters that cover topics such as erosion estimation methods, sediment transport modeling, reservoir sedimentation modeling, sustainable reservoir development and management, and river restoration processes. It is intended to help engineers and scientists study and manage erosion, sedimentation, and reservoir sustainability issues. The document provides an overview of the technical content and organization of the full Erosion and Sedimentation Manual.
This document provides an introduction to design for the environment (DfE), which is a systematic approach to considering the entire lifecycle of a product during the design process. It discusses using nature as inspiration for design solutions through biomimicry. The document then covers each stage of a product's lifecycle - materials selection, manufacturing, use, transport/packaging, and end of life - highlighting opportunities for more sustainable design at each stage. Checklist questions are provided to help guide application of DfE principles. Finally, the document lists various tools that can be used to implement and measure the impacts of DfE, including checklists, flowcharts, impact assessment software, and standards like ISO 14001.
Similar to BioFilters for Pollution Removal from Storm Water (20)
This document discusses the history and forms of water harvesting. It begins by providing context on water harvesting's past role in agriculture and recent renewed interest. It then describes six main forms of water harvesting: 1) roof top, 2) for animal consumption, 3) inter-row, 4) microcatchment, 5) medium-sized catchment, and 6) large catchment. Each form is characterized by parameters like catchment area, cropping area, precipitation levels, and slope. The goal of water harvesting is to increase plant production in dry areas by concentrating rainfall runoff.
Water harvesting and development for improving productivity - Part 2Sotirakou964
This document provides information on rainwater harvesting techniques. It discusses roof harvesting where rainwater is collected from house roofs through gutters and pipes into storage tanks. The first water during rains should be diverted to flush dust and debris, while later water can be collected. Runoff harvesting and floodwater harvesting are also briefly mentioned as other rainwater collection methods. Guidelines are provided on roof cleaning, gutter sloping, and basic system designs to collect and store rainwater for domestic and agricultural use.
Santa Monica CA Rainwater Harvesting ManualSotirakou964
This document provides an introduction and overview of the City of Culver City's Rainwater Harvesting Program. The program aims to help homeowners capture rainwater from their roofs and redirect it to on-site pervious areas or rain barrels to reduce stormwater runoff. Harvesting rainwater provides benefits such as protecting water resources, reducing energy demands, practicing water conservation, and recharging groundwater supplies. The document outlines options for redirecting rainwater and provides guidance on assessing sites, measuring slopes, and installing rain barrels or building rain gardens to harvest rainwater on one's own property.
Stormwater planters are structures designed to capture, filter, and infiltrate or convey stormwater runoff. There are two main types: infiltration planters which allow water to seep into surrounding soils, and filtration planters which are lined to prevent infiltration and only cleanse stormwater before routing it to an approved disposal point. Planters provide stormwater management benefits and can be customized for different settings. They are sized based on the amount of runoff directed to them and factors like ponding depth and infiltration rate. Soils are typically amended to support plant life while allowing proper infiltration.
Santa Barbarba Sustainable Landscaping ManualSotirakou964
The document provides guidance on sustainable landscaping for homeowners in Santa Barbara County. It discusses planning a landscape that is resource efficient and reduces waste, which can save homeowners time and money while benefiting the environment. The key aspects of sustainable landscaping covered are reducing lawn areas, using water-efficient native plants, installing efficient irrigation, and designing functional outdoor spaces. Analyzing the site conditions and planning phases are emphasized as important first steps to having a sustainable landscape.
Sacaramento CA: Lawnless and Loving It ManualSotirakou964
This document discusses the benefits of removing lawns and replacing them with more sustainable landscaping options. It notes that lawns require large amounts of water and pesticides. Some alternatives to lawns mentioned include habitat gardens, edible gardens, meadows, rain gardens, rock gardens, and children's gardens planted with native species. Native plants are advocated because they are adapted to the local environment and provide benefits like requiring less water and maintenance than non-natives. Examples of lawn removal projects and their before and after appearances are also shown and described.
This document provides an introduction to conservation landscaping techniques like rain gardens and xeriscapes. It summarizes the philosophy and rationale for using native plants in landscaping to restore and protect local habitats. Examples are given from demonstration gardens at the Chesapeake Ecology Center, with plant lists and descriptions. The guide covers topics such as landscape design principles, how to plan and install conservation gardens, and lists of commonly used native trees and shrubs for the Chesapeake Bay watershed region. Its goal is to educate and inspire readers to adopt these practices in their own yards and communities.
Green roofs, also known as living roofs, allow plants to grow on building roofs. They provide environmental benefits like reducing stormwater runoff and the urban heat island effect. While initially costly, green roofs last longer than traditional roofs and provide savings over time. When planning a green roof, homeowners should consider their roof's slope, climate conditions, and structural ability to support additional weight. Green roofs have multiple layers, including a waterproof membrane, drainage layer, lightweight growing media, and drought-tolerant plants. Proper planning and installation are needed to ensure a successful green roof.
This document provides an overview of natural insecticides that can be used in organic gardening. It describes several botanical insecticides including pyrethrum, sabadilla, rotenone, nicotine, and neem oil. The insecticides are derived from plants and have low toxicity to humans. The document provides instructions on safely applying natural insecticides, including only using them when needed, wearing protective equipment, thoroughly covering plants, and following label directions. It emphasizes using multiple pest control methods to keep insect populations low and reduce reliance on insecticides.
OR: Portland: Multnomah Building Green RoofSotirakou964
The document summarizes a green roof project on the Multnomah Building in Portland, Oregon. The 12,000 square foot green roof was intended to demonstrate the benefits of green roofs, including increased roof longevity, stormwater management through reduced runoff and pollution, and improved aesthetics. The total project cost was $343,000, with the green roof construction costing $179,801. Various organizations provided grants and materials to support the project as a demonstration of green roof technologies.
New York City: Rainwater Harvesting ManualSotirakou964
This document provides an introduction to rainwater harvesting systems. It discusses the history of rainwater harvesting around the world dating back thousands of years. It then describes the basic components of a rainwater harvesting system, including the roof, gutters, downspout, first flush system, storage tank, overflow pipe, and optional connections to a rain garden. Diagrams and photographs help illustrate the different parts of a typical system.
Beyond More Crop per Drop: Farming & Sustainable DevelopmentSotirakou964
This document provides a list of resources for bay friendly landscaping. It includes websites and organizations related to air quality, alternatives to pesticides, bay-friendly standards and trainings, beneficial insects, composting, erosion control, fire resistant plants, green businesses, greywater systems, and hazardous waste disposal. The list is intended to support professionals in implementing sustainable landscape practices.
La Plaza Garden CA: Water Efficient GardeningSotirakou964
This document provides information about La Plaza Garden, a water-efficient demonstration garden in Cotati, California. The garden uses various techniques like drought-tolerant plants, water harvesting, and habitat creation to conserve water and other resources. It includes seven distinct garden areas showcasing different techniques, plants, and habitats. The document also provides additional resources for water-efficient and native plant gardening.
This document provides a summary of key considerations for rainwater harvesting systems in small island Caribbean environments. It outlines the main components of a rainwater harvesting system including the catchment area, conveyance system, and storage. Formulas are provided to calculate the volume of water that can be captured from a roof catchment area. Guidelines aim to assist homeowners, contractors, and farmers in best practices for installing and operating rainwater harvesting systems.
An extensive green roof has less than six inches of growing medium and can support grasses and small shrubs, while an intensive green roof has 6-24 inches of medium and supports larger plants. A green roof absorbs up to half of rainfall and greatly increases roof insulation. Steps to install a green roof include adding a vapor barrier, insulation, waterproof membrane, drainage layer, growth medium, and selecting plants suited to the climate from a list provided. Cost is approximately $15-25 per square foot but reduces runoff and provides other benefits.
Waterbird Conservation for the AmericasSotirakou964
This document provides a framework for conserving waterbird populations throughout the Americas. It sets broad goals such as advocating continent-wide monitoring, regional conservation planning, and national/local action. The plan aims to weave together resources, science, and stakeholders to achieve sustainable waterbird populations and habitat management across their ranges. It emphasizes initial priorities like seabirds and colonial nesters in northern areas, with plans to expand coverage over time. Implementation will rely on partnerships across geographic and organizational boundaries to coordinate waterbird conservation efforts internationally, nationally, regionally, and locally throughout the Americas.
Nisqually National Wildlife Refuge Educator's GuideSotirakou964
This document provides an educator's guide to the Nisqually National Wildlife Refuge. It includes information about the refuge's habitats and wildlife, as well as guidance for planning field trips, including pre-field trip activities, hands-on activities during field trips, and post-field trip activities. The goal is to enhance students' learning experiences through field trips to the refuge and increase environmental awareness in the community. The guide takes a comprehensive, hands-on approach to environmental education.
The document is a teacher's guide for the AWARE Kids program, which aims to educate elementary school students about ocean conservation. It includes an introduction to the program, correlations to national science standards, lessons on topics like coral reefs and sea turtles, and hands-on activities. The guide is designed to integrate science, math, art and other subjects while teaching about underwater environments and conservation issues in an interactive way.
The document provides background information on a teachers guide and poster about stream ecosystems. It includes an introduction to the poster's depiction of a typical middle order stream and the species selected. It discusses the life cycles of frogs, insects, and mussels shown in the poster which involve metamorphosis. It also describes suggested classroom activities teachers can use with the poster, including having students draw life cycles, simulate ecosystem changes, or create imaginary rabbit metamorphosis. The guide concludes with discussions of food chains, energy use, nutrient recycling, and how adaptability to available food impacts species survival.
The document is a curriculum guide for teaching coldwater conservation and trout habitat education. It includes 17 activities to teach students about ecological concepts, hydrology, stream life, trout behavior and biology, human impacts on streams, and sustainable fishing practices. The guide is intended to complement fly fishing instruction by providing the scientific background on healthy trout habitats and how human activities can positively or negatively affect these habitats. It contains suggestions for how to use the guide, definitions of key terms, and references for additional teaching resources.
“An Outlook of the Ongoing and Future Relationship between Blockchain Technologies and Process-aware Information Systems.” Invited talk at the joint workshop on Blockchain for Information Systems (BC4IS) and Blockchain for Trusted Data Sharing (B4TDS), co-located with with the 36th International Conference on Advanced Information Systems Engineering (CAiSE), 3 June 2024, Limassol, Cyprus.
Dr. Sean Tan, Head of Data Science, Changi Airport Group
Discover how Changi Airport Group (CAG) leverages graph technologies and generative AI to revolutionize their search capabilities. This session delves into the unique search needs of CAG’s diverse passengers and customers, showcasing how graph data structures enhance the accuracy and relevance of AI-generated search results, mitigating the risk of “hallucinations” and improving the overall customer journey.
Cosa hanno in comune un mattoncino Lego e la backdoor XZ?Speck&Tech
ABSTRACT: A prima vista, un mattoncino Lego e la backdoor XZ potrebbero avere in comune il fatto di essere entrambi blocchi di costruzione, o dipendenze di progetti creativi e software. La realtà è che un mattoncino Lego e il caso della backdoor XZ hanno molto di più di tutto ciò in comune.
Partecipate alla presentazione per immergervi in una storia di interoperabilità, standard e formati aperti, per poi discutere del ruolo importante che i contributori hanno in una comunità open source sostenibile.
BIO: Sostenitrice del software libero e dei formati standard e aperti. È stata un membro attivo dei progetti Fedora e openSUSE e ha co-fondato l'Associazione LibreItalia dove è stata coinvolta in diversi eventi, migrazioni e formazione relativi a LibreOffice. In precedenza ha lavorato a migrazioni e corsi di formazione su LibreOffice per diverse amministrazioni pubbliche e privati. Da gennaio 2020 lavora in SUSE come Software Release Engineer per Uyuni e SUSE Manager e quando non segue la sua passione per i computer e per Geeko coltiva la sua curiosità per l'astronomia (da cui deriva il suo nickname deneb_alpha).
Building Production Ready Search Pipelines with Spark and MilvusZilliz
Spark is the widely used ETL tool for processing, indexing and ingesting data to serving stack for search. Milvus is the production-ready open-source vector database. In this talk we will show how to use Spark to process unstructured data to extract vector representations, and push the vectors to Milvus vector database for search serving.
Programming Foundation Models with DSPy - Meetup SlidesZilliz
Prompting language models is hard, while programming language models is easy. In this talk, I will discuss the state-of-the-art framework DSPy for programming foundation models with its powerful optimizers and runtime constraint system.
For the full video of this presentation, please visit: https://www.edge-ai-vision.com/2024/06/building-and-scaling-ai-applications-with-the-nx-ai-manager-a-presentation-from-network-optix/
Robin van Emden, Senior Director of Data Science at Network Optix, presents the “Building and Scaling AI Applications with the Nx AI Manager,” tutorial at the May 2024 Embedded Vision Summit.
In this presentation, van Emden covers the basics of scaling edge AI solutions using the Nx tool kit. He emphasizes the process of developing AI models and deploying them globally. He also showcases the conversion of AI models and the creation of effective edge AI pipelines, with a focus on pre-processing, model conversion, selecting the appropriate inference engine for the target hardware and post-processing.
van Emden shows how Nx can simplify the developer’s life and facilitate a rapid transition from concept to production-ready applications.He provides valuable insights into developing scalable and efficient edge AI solutions, with a strong focus on practical implementation.
Best 20 SEO Techniques To Improve Website Visibility In SERPPixlogix Infotech
Boost your website's visibility with proven SEO techniques! Our latest blog dives into essential strategies to enhance your online presence, increase traffic, and rank higher on search engines. From keyword optimization to quality content creation, learn how to make your site stand out in the crowded digital landscape. Discover actionable tips and expert insights to elevate your SEO game.
Pushing the limits of ePRTC: 100ns holdover for 100 daysAdtran
At WSTS 2024, Alon Stern explored the topic of parametric holdover and explained how recent research findings can be implemented in real-world PNT networks to achieve 100 nanoseconds of accuracy for up to 100 days.
HCL Notes und Domino Lizenzkostenreduzierung in der Welt von DLAUpanagenda
Webinar Recording: https://www.panagenda.com/webinars/hcl-notes-und-domino-lizenzkostenreduzierung-in-der-welt-von-dlau/
DLAU und die Lizenzen nach dem CCB- und CCX-Modell sind für viele in der HCL-Community seit letztem Jahr ein heißes Thema. Als Notes- oder Domino-Kunde haben Sie vielleicht mit unerwartet hohen Benutzerzahlen und Lizenzgebühren zu kämpfen. Sie fragen sich vielleicht, wie diese neue Art der Lizenzierung funktioniert und welchen Nutzen sie Ihnen bringt. Vor allem wollen Sie sicherlich Ihr Budget einhalten und Kosten sparen, wo immer möglich. Das verstehen wir und wir möchten Ihnen dabei helfen!
Wir erklären Ihnen, wie Sie häufige Konfigurationsprobleme lösen können, die dazu führen können, dass mehr Benutzer gezählt werden als nötig, und wie Sie überflüssige oder ungenutzte Konten identifizieren und entfernen können, um Geld zu sparen. Es gibt auch einige Ansätze, die zu unnötigen Ausgaben führen können, z. B. wenn ein Personendokument anstelle eines Mail-Ins für geteilte Mailboxen verwendet wird. Wir zeigen Ihnen solche Fälle und deren Lösungen. Und natürlich erklären wir Ihnen das neue Lizenzmodell.
Nehmen Sie an diesem Webinar teil, bei dem HCL-Ambassador Marc Thomas und Gastredner Franz Walder Ihnen diese neue Welt näherbringen. Es vermittelt Ihnen die Tools und das Know-how, um den Überblick zu bewahren. Sie werden in der Lage sein, Ihre Kosten durch eine optimierte Domino-Konfiguration zu reduzieren und auch in Zukunft gering zu halten.
Diese Themen werden behandelt
- Reduzierung der Lizenzkosten durch Auffinden und Beheben von Fehlkonfigurationen und überflüssigen Konten
- Wie funktionieren CCB- und CCX-Lizenzen wirklich?
- Verstehen des DLAU-Tools und wie man es am besten nutzt
- Tipps für häufige Problembereiche, wie z. B. Team-Postfächer, Funktions-/Testbenutzer usw.
- Praxisbeispiele und Best Practices zum sofortigen Umsetzen
Why You Should Replace Windows 11 with Nitrux Linux 3.5.0 for enhanced perfor...SOFTTECHHUB
The choice of an operating system plays a pivotal role in shaping our computing experience. For decades, Microsoft's Windows has dominated the market, offering a familiar and widely adopted platform for personal and professional use. However, as technological advancements continue to push the boundaries of innovation, alternative operating systems have emerged, challenging the status quo and offering users a fresh perspective on computing.
One such alternative that has garnered significant attention and acclaim is Nitrux Linux 3.5.0, a sleek, powerful, and user-friendly Linux distribution that promises to redefine the way we interact with our devices. With its focus on performance, security, and customization, Nitrux Linux presents a compelling case for those seeking to break free from the constraints of proprietary software and embrace the freedom and flexibility of open-source computing.
TrustArc Webinar - 2024 Global Privacy SurveyTrustArc
How does your privacy program stack up against your peers? What challenges are privacy teams tackling and prioritizing in 2024?
In the fifth annual Global Privacy Benchmarks Survey, we asked over 1,800 global privacy professionals and business executives to share their perspectives on the current state of privacy inside and outside of their organizations. This year’s report focused on emerging areas of importance for privacy and compliance professionals, including considerations and implications of Artificial Intelligence (AI) technologies, building brand trust, and different approaches for achieving higher privacy competence scores.
See how organizational priorities and strategic approaches to data security and privacy are evolving around the globe.
This webinar will review:
- The top 10 privacy insights from the fifth annual Global Privacy Benchmarks Survey
- The top challenges for privacy leaders, practitioners, and organizations in 2024
- Key themes to consider in developing and maintaining your privacy program
Threats to mobile devices are more prevalent and increasing in scope and complexity. Users of mobile devices desire to take full advantage of the features
available on those devices, but many of the features provide convenience and capability but sacrifice security. This best practices guide outlines steps the users can take to better protect personal devices and information.
Observability Concepts EVERY Developer Should Know -- DeveloperWeek Europe.pdfPaige Cruz
Monitoring and observability aren’t traditionally found in software curriculums and many of us cobble this knowledge together from whatever vendor or ecosystem we were first introduced to and whatever is a part of your current company’s observability stack.
While the dev and ops silo continues to crumble….many organizations still relegate monitoring & observability as the purview of ops, infra and SRE teams. This is a mistake - achieving a highly observable system requires collaboration up and down the stack.
I, a former op, would like to extend an invitation to all application developers to join the observability party will share these foundational concepts to build on:
Unlock the Future of Search with MongoDB Atlas_ Vector Search Unleashed.pdfMalak Abu Hammad
Discover how MongoDB Atlas and vector search technology can revolutionize your application's search capabilities. This comprehensive presentation covers:
* What is Vector Search?
* Importance and benefits of vector search
* Practical use cases across various industries
* Step-by-step implementation guide
* Live demos with code snippets
* Enhancing LLM capabilities with vector search
* Best practices and optimization strategies
Perfect for developers, AI enthusiasts, and tech leaders. Learn how to leverage MongoDB Atlas to deliver highly relevant, context-aware search results, transforming your data retrieval process. Stay ahead in tech innovation and maximize the potential of your applications.
#MongoDB #VectorSearch #AI #SemanticSearch #TechInnovation #DataScience #LLM #MachineLearning #SearchTechnology
Presentation of the OECD Artificial Intelligence Review of Germany
BioFilters for Pollution Removal from Storm Water
1. BIOFILTERS
(Bioswales, Vegetative Buffers, & Constructed Wetlands)
For
Storm Water Discharge
Pollution Removal
Guidance for using Bioswales, Vegetative Buffers, and
Constructed Wetlands for reducing, minimizing, or eliminating
pollutant discharges to surface waters
By
Dennis Jurries, PE
NWR Storm Water Engineer
DEQ Northwest Region Document
January 2003
2. This document is an attempt to compile the best available information on the design and
use of biofilters (bioswales, vegetated filter strips, and constructed wetlands) so that those
sites that may have an application of one or the other of these vegetated filtering systems
will have information to make the best decision on the design, construction, implementa-
tion, and maintenance of these Best Management Practices. It is not a design manual but
a practical, based on experience and knowledge of sites that implemented these BMPs,
useful information on what works and does not work when designing, constructing, and
operating them. Research is needed to determine the effect these BMPs will have on
turbidity and other pollutants but there are indications that their effect will be positive and
of environmental benefit.
Bioswales and constructed wetlands are being used more and more to address pollutants
in storm water runoff. Many installations of these BMPs have failed or have not been as
successful as was hoped when their use was first contemplated. Most of the limited suc-
cess or failures can be attributed to insufficient information being available or to bad or
no expert input into the design, construction, vegetating, or maintenance of the bioswale
or constructed wetland. It is hoped that this document will provide that useful informa-
tion and reason to seek out those that have the expertise to be of help.
As long as a constructed wetland is not built in a natural wetland, waterway, or flood-
plain, EPA and the Oregon Division of State Lands views the wetland as a private treat-
ment method that does not require wetland permitting and it is treated different from the
way a natural wetland is treated.
Additional copies of this document are available on the internet at
http://www.deq.state.or.us/nwr/stormwater.htm.
4. Table of Contents Continued
Oregon Constructed Wetlands ...................................................................................... 45
Examples....................................................................................................................... 46
Commercial Office/Lab Constructed Wetland....................................................... 46
Public Park Constructed Pocket Wetland............................................................... 46
Aggregate Mining Site Constructed Wetland ........................................................ 47
Industrial Constructed Wetland.............................................................................. 48
Pocket Constructed Wetlands................................................................................. 49
References......................................................................................................................... 51
5. Background
Nature uses vegetated depressions, wetlands, marshes, etc. to clean storm water runoff by
removing sediments, turbidity, heavy metals, and other pollutants. How this is accom-
plished is complex. Some pollutants are removed by vegetation uptake, some by natural
flocculation from decomposing vegetation, some by just slowing the flow down enough
for sedimentation to occur, and some by biota consumption and ionic attraction around
the root structure.
Many pollutants migrate attached to soil particles and soil particles in themselves are
considered a pollutant. When storm water runoff leaves a site, unless there is effective
erosion protection such as vegetation, soil also leaves the site, in the forms of sediment,
suspended solids, and microscopic soil particles called colloidal suspension, dissolved
solids, or turbidity. The soil particulate can be clay, minerals, organic material, heavy
metals, etc. Sediment usually will readily settle out. Suspended solids will settle out
providing the velocity of the runoff stream is not too large. Turbidity usually will not be
removed from the water column with out something else acting upon it to remove it.
Sediment and suspended solids are
detrimental to fish spawning beds.
Turbidity reduces light penetration,
increases water temperature, smoth-
ers stream bottom habitats, smothers
larvae, clogs or damages gill struc-
tures, and reduces oxygen in water.
The level of turbidity that it takes to
be detrimental varies with duration.
(See chart below.)
Turbid and Clean Storm Water
RELATIONSHIP
OF
TURBIDITY (N.T.U.) (Log10)
FISH ACTIVITY
TO
TURBIDITY
LO R
NG ED
TE DE UC
RM LA ED DE
AT
REYEDGR H
IN CO DU H OW
IN CR VE CT AT TH
CR R E A R IO CH R
EA ED AS VO AB N IN AT
SE UC ED ID AN IN G ES
D E R AN D FE
CO D ES C ON ED
UGFEE PIRE ED IN
ST H DI AT G
RE IN N I
SS G G ON
RA
TE
S
TIME (Log10)
Page 1 of 52
6. Studies reported by Lloyd et al (1987) describe rainbow trout avoidance of turbid water
above 30 Neophelometric Turbidity Units (NTU). The avoidance of turbid water has
been documented by both field and laboratory studies. Bilby (1982) observed coho
salmon avoidance at water turbidity levels above 70 NTU. The avoidance behavior has
been associated with the fish’s ability to see. Several studies discussed by Lloyd et al
(1987) suggest significantly reduced angler success at turbidities ranging from 8 - 50
NTU which suggests a reduced ability of the fish to locate prey. Lloyd (1987) cites
Buck, 1956, Tebo 1956, Bartsch 1960, Oschwald 1972, Ritter and Ott 1974, and Langer
1980 as providing additional descriptions of reduced angler success associated with tur-
bidity. The USEPA (1977) reported that cutthroat trout abandoned redds, sought cover
and stopped feeding when a turbidity of 35 NTU was encountered for two hours. In addi-
tion USEPA (1977) reported reduced growth and feeding at 50 mg/l TSS.
Summary of Turbidity (NTU) Cited Impairment Thresholds
Turbidity Impairment
5-25 Reduced primary production
8 (8-50) Reduced angler success
11-49 Emigration (salmonid)
(3-30) Cough response/Avoidance (salmonid)
21 Reduced salmonid population density
25 Reduced feeding and growth in salmonid, prolonged exposure
30 Trout avoidance
35 Redds abandoned
50 Juvenile displacement
60 Feeding and territorial behavior disrupted
70 Avoidance by older salmonid
Economical methods for removing turbidity and suspended solids from storm water run-
off are limited. Bioswales and constructed wetlands my be the most economical ap-
proach, when both initial and maintenance costs are considered, for removing turbidity
and suspended solids along with other pollutants.
Page 2 of 52
7. General
Before delving into specifics concerning vegetative removal of pollutants through the use
of bioswales, phytofiltration (vegetative filter buffers), and constructed wetlands it is im-
portant to look at the mechanisms and conditions that actually remove the pollutants.
These conditions and mechanisms can be broken out into three areas:
1. Soils,
2. Biological organisms, and
3. Vegetation.
Soils
Constructed wetlands, phytofiltration, and bioswales can be successfully built and oper-
ated in most soil types provide the subsoil in the area of the biofilter is optimized for the
maximum benefit of the biofilter. The subsoil can include soil, sand, gravel, rock, and
organic materials such as compost or composted biosolids (composted sewage treatment
plant sludge). Sediments, naturally settled suspended solids and colloidal suspensions
(turbidity) will accumulate in the biofilter from the low velocity of water flow, natural
flocculation, bioactivity, and decaying vegetation to add to the substrate (bottom) where
vegetative uptake can make use of it. The substrate is important and should be uncom-
pacted because:
• it will support many of the living organisms (biota) that make the biofilter work,
• the permeability of the substrate affects the movement of water through the biofilter,
• many chemical and biological transformations take place within the substrate as part
of the soil food web,
• contaminate storage is provided, and
• a source of carbon, microbial attachment and material exchange is provided.
Soils must be non-compacted to promote good root development, biological organism
development, water retention for dry periods, and to provide some filtering and infiltra-
tion. They must initially contain carbon and nutrients for initial vegetation and biota
(biological colonies) establishment.
Under some conditions infiltration is undesirable due to either the pollutants being re-
moved or to the need to retain water for through the dry season. In this case either a liner
must be established or a confining impermeable layer such as clay must be installed be-
low the depth of the active growth media of soil.
When soil is used as a filtering media, the following soil properties that should be consid-
ered are:
• Cation Exchange Capacity (depending on the pollutants of concern),
• Anion Exchange Capacity (depending on the pollutants of concern),
• pH,
Page 3 of 52
8. • Electrical Conductivity,
• texture,
• organic matter, and
• air entrainment or soil compaction.
If the pollutants to be removed from the storm water are positively charged (ions) metals
such as Copper, Cadmium, Iron, Manganese, Aluminum, Mercury, etc., then an anionic
(negatively charged) soil should be present. Most soils are negatively charged. The rec-
ommended CEC is at least 15 milliequivalent/100 grams of soil. On the other hand, if
turbidity or colloidal suspensions are to be removed from the storm water then, an cati-
onic or positively charged soil would be helpful. A positively charged soil is not neces-
sary, due to other mechanisms in the wetland, which will provide the positive charge to
attract the negatively charged colloidal particles.
Clay Types Organic Matter 200-400 meq/100 g
Kaolinite 3-15 meq/100 g
Illite 15-40 meq/100 g
Montmorillonite 80-100 meq/100 g
The retention of heavy metals and nutrients is influenced by the pH of the soil. The pH
of the soil should be between 6.5 and 8.5 for optimal results. Soil pH also impacts the
CEC. Soil CEC can be expected to increase up to 50% by increasing the pH of the soil
from 4.0 to 6.5 and almost 100% if the pH were increased from 4.0 to 8.0.
The soil Electrical Conductivity influences the ability of the vegetation and the microbial
food chain to process the pollutants and nutrients in the storm water flow. An EC of 4
micromho/centimeter or less is the ideal level for good plant and biota growth.
Soil texture can impact the infiltration characteristics and influence the Cation Exchange
Capacity.
Sand 1-5 meq/100 g Fine Sandy Loam 5-10 meq/100 g
Loam 5-15 meq/100 g Clay Loam 15-30 meq/100 g
Clay >30 meq/100 g
Since constructed treatment wetlands are often constructed by excavating, the soil is of-
ten depleted of organic material that is necessary for plant growth and good microbial
activity. Organic material can also consume oxygen and thus create an anoxic environ-
ment that may not be conducive to the desired biological environment unless nitrate re-
duction or neutralization of acidic drainage is desired. Compost or some other organic
material must be reintroduced into the soil. The amount of compost additive used should
be carefully considered for the desired results.
Page 4 of 52
9. Biological
Biofilter pollutant removal is largely regulated by microorganisms. The biota acts as a
major stabilization, removal, and conversion mechanism for organic carbon and many
nutrients. It appears that most biological action occurring in a constructed wetland is an-
aerobic. Due to flow fluctuations over the year, some biological action is fracultative
(both aerobic (air breathing) and anaerobic depending on the seasonal conditions). Mi-
crobial action:
• converts or transforms many substances into insoluble or harmless substances,
• positively changes the reduction/oxidation (redox) increasing the processing ca-
pacity of the wetland soil to remove pollutants, and
• is a major contributor to the recycling of nutrients.
Non-compacted or disturbed soil contains voids or air spaces. In submerged soils water
replaces the air in those spaces and microbial action rapidly consumes the residual air.
Microbial action changes from aerobic to anaerobic and the soil becomes anoxic (without
oxygen). This soil then becomes a reducing environment, which is important for removal
of pollutants such as nitrogen and metals. Also a loose non-compacted substrate is impor-
tant for good vegetation root growth.
The establishment and maintenance of a healthy biological colony may be the most im-
portant aspect of the construction and continuing viability of the biofilter. The right biota
for the biofilter is important because it is the microorganisms to a great extent, which
capture and convert pollutants and nutrients into a form, which can be easily consumed
by the vegetation. Many pollutants are in an insoluble form, which vegetation can not
use. The biological food chain converts these nutrients and pollutants from their stable
insoluble form into ones, which are easily consumed by the vegetation established in the
biofilter. The microorganisms work in a symbiosis with the plants to capture and uptake
the pollutants and nutrients in the storm water runoff. Endomycorrhiza or arbuscular my-
corrhizae fungi help the vegetation root structure bring in water and nutrients from as
much as fifty feet away from the plant roots. These organisms can help the plant survive
in the summer and in drought conditions.
The establishment of health soil biota can be accomplished through the tilling of compost
into the soil of the biofilter during construction or through the preparation of the biofilter
soil by the addition of a carbon source, fertilizer, material to loosen the soil, and commer-
cially available biological organisms.
Biological organisms will collect pollutants and change them into a form that makes them
more susceptible to vegetation uptake or renders them in a form that is not a pollutant.
The soil must be uncompacted for the biota to thrive and to allow the vegetation roots to
develop properly. Further detailed information on the use of compost for biota estab-
lishment and decompaction of the biofilter’s soil can found in the document “Environ-
Page 5 of 52
10. mental Protection and Enhancement with Compost” at
http://www.deg.state.or.us/nwr/stormwater.htm and other documents.
Vegetation
Sedimentation comes about through reduced flow, ion exchange, and natural flocculation.
Slower velocities within a biofilter allow higher retention times of pollutants and settling
of the larger particle sized pollutants. Many of the particles suspended in the storm water
are negatively charged. There is a positive charge at the base of the vegetation in a biofil-
ter that attracts and settles these negatively charged particles. As vegetation ages and
discards plant material or dies a natural flocculent can be released, which attracts nega-
tively charged pollutant particles and causes them to settle out. Soil will filter out pollut-
ants in any water that flows through the soil subsurface. Vegetation will consume pollut-
ants and transfer them into their plant matter.
Native plant species are a must in Oregon for use in biofilter design. Proper selection of
native species can provide year-round vegetative cover without need for supplemental
irrigation or fertilization. Furthermore, native species usually provide high habitat value
for indigenous birds and other animals. Exotic non-native species can become invasive if
allowed to proliferate. Local municipal agencies, the County Soil Conservation Service
Field Office of the Department of Agriculture, or environmental restoration groups can
provide guidance on appropriate species. Local landscape ordinances often provide lists
of acceptable and non-acceptable plants and grasses.
The picture above shows the filtering effect of sedge. Notice the clearer water on the
right side of the picture (downstream).
Page 6 of 52
11. The selection and planting of vegetation should be in accordance with the pollutants to be
removed, and the flow and velocity design requirements for the biofilter. Selection of turf
or woody plants depends on the desired capacity and residence time of the storm water
and pollutants in the biofilter. Woody plant materials should only be planted on the side
slopes. Trees should only be planted along the edge of the biofilter to provide shade to
minimize the temperature increase to the water in the dry months. A lower canopy of
shrubs and grasses should be planted underneath the trees.
Bioswales are generally composed of three basic vegetation zones: highest (xeric), mid-
dle (mesic), and lowest (hydric). Plant the lowest zone with species that can tolerate
standing water and fluctuating water levels. Plant the middle zone with species that toler-
ate slightly drier conditions and more infrequent fluctuating water levels. Middle zone
plants, along the slopes, are often selected for erosion control. Plant the highest zone with
species adapted for drier conditions.
Grass meets many of the functional criteria for biofilter vegetation, such as dense cover,
fibrous root or rhizome structure, and upright growth form. This plant material must be
seeded for uniform coverage at rates high enough to provide a dense stand of grass. If a
biofilter is planted in the early summer supplemental irrigation or use of compost or a
product such as DriWaterTM may be required to ensure germination and growth prior to
the wet season. Geotextiles, such as jute matting, compost, and straw mulching may be
needed to provide physical protection of the seed and slope, if the biofilter is planted
shortly before the wet season. Hobbs & Hopkins of Portland has a bioswale system that
contains a liner that can be applied in the wet season with seeding to take place in the late
spring. The vegetation grows down through the liner rather than up through as with most
geotextiles. This bioswale system could also be used on the banks of wetlands
Annual grasses are fast-germinating and fast-growing plants that spread quickly and ex-
tensively through seed dispersal. These plants react immediately to moisture, producing a
fast ground cover following the first rains. They are appropriate for situations requiring
quick, temporary channel protection and where full, even coverage is desired. Plant
growth is usually stimulated by mowing. This can be beneficial during dry periods as
plants require less water when kept small.
Perennial grasses grow more slowly than annual grasses. Perennial grasses are generally
sod-forming or bunch-grasses. Sod-forming grasses develop stems and shoots from un-
derground rhizomes. Bunch grasses grow in clumps and require dense stands to cover the
ground completely. The growth period of perennial grasses corresponds with available
moisture and favorable temperatures (late winter to midspring for western states). Shal-
low-rooted perennial grasses die back to the underground runners, root masses, and stem
bases when the supply of surface water disappears during drought.
Plants for biofilters in arid climates may require irrigation for establishment and for dry
periods. To ensure seed germination and grass establishment, temporary irrigation, com-
post, or products like DriWaterTM can be used to help establish grass. A permanent irriga-
tion system should be provided for and used in regions with significant dry seasons.
Page 7 of 52
12. Vegetation selected for biofilters should be natural for the region in which the bioswale is
located. The vegetation should not be dormant in the October through May season. Low
maintenance and aesthetics in some areas are other considerations. Remember that mow-
ing or cutting of the vegetation usually reduces their ability to remove pollutants by vege-
tation uptake but some vegetation removal will probably be necessary in order to main-
tain the vegetations ability to continue to uptake the incoming pollutants in the storm wa-
ter. Two books available on wetland vegetation in Oregon are: Wetland Plants of Ore-
gon & Washington, by Jennifer Guard, 1995; and A Field Guide to the Common Wetland
Plants of Western Washington & Northwestern Oregon, by the Seattle Audubon Society
and the Washington Native Plant Society, Sara Spear Cooke, Editor, 1997.
Some types of vegetation to consider are: rushes for heavy metal and nutrient uptake;
reedgrass for TSS and erosion control; common reed for TSS, nutrient uptake, and
chemicals; water-starwort for absorption of toxics; water-purslane for filtering and uptake
of toxics; burreeds for pollutant uptake; clover for erosion control and nitrogen capture;
and Mexican mosquito-fern for uptake of toxics. Many other types of vegetation will
help remove TSS and turbidity. Cattail phosphorus removal is on the order of 80 percent.
Cattails are very good for removing pollutants from storm water but have several draw-
backs. Among these drawbacks are: they are highly invasive and tend to take over the
swale, have a dormant cycle that can extend for a year or more, and they tend to overly
restrict the flow in the bioswale requiring abnormally high amounts of maintenance of the
bioswale.
Cattails crowding out
other vegetation in
bioswale
Bluegrass has a nutrient uptake of 200 pounds per acre, a phosphorus uptake of 29
pounds per acre, and a potassium uptake of 149 pounds per acre each year. Tall Fescue
has a nutrient uptake of 135 pounds per acre, a phosphorus uptake of 24 pounds per acre,
and a potassium uptake of 149 pounds per acre each year. Brome Grass has a nutrient
uptake of 166 pounds per acre, a phosphorus uptake of 29 pounds per acre, and a potas-
sium uptake of 211 pounds per acre each year. If the clippings from the mowing or the
Page 8 of 52
13. grass are removed then, this will give an indication of the shallow soil and/or pollutant
runoff removal rates for these various grasses.
Pollutant removal from vegetative uptake drops after the vegetation matures unless the
dead vegetation is constantly removed to break the cycle of re-entrainment through the
re-release of the pollutants from the decaying vegetation. Vegetation should be selected
for the climate, the expected pollutants, the expected depth of the water, and the season
that the vegetation needs to be active (usually in the late fall, winter, and spring during
the rainy season).
Bioswale Vegetation
The following is a list of bioswale vegetation for Northwest Oregon furnished by
GreenWorks P.C.
Bioswale Bottom
Groundlayer
Scientific Name Common Name
Agrostis tenuis Colonial Bentgrass
Carex densa Dense Sedge
Carex obnupta Slough Sedge
Deschampsia cespitosa Tufted Hairgrass
Eleocharis palustris Creeping Spikerush
Epilobium densiflorum Dense Spike-Primrose
Hypericum anagalloides Bog St. John’s- Wort
Juncus acuminatus Taper-Tipped Rush
Juncus articulatus Jointed Rush
Juncus effusus Common Rush
Juncus tenuis Slender Rush
Mimulus guttatus Common Monkeyflower
Potentilla gracilis Northwest Cinquefoil
Ranunculus alismifolius Dwarf Buttercup
Ranunculus occidentalis Western Buttercup
Saxifraga oregana Oregon Saxifrage
Side Slopes
Groundlayer
Scientific Name Common Name
Bromus carinatus California Brome
Deschampsia cespitosa Tufted Hairgrass
Elymus glaucus Blue Wildrye
Festuca occidentalis Western Fescue Grass
Page 9 of 52
14. Side Slopes
Understory
Scientific Name Common Name
Cornus stolonifera Redosier Dogwood
Crataegus douglasii Black Hawthorne
Lonicera involcrata Black Twinberry
Oemlaria cerasiformis Indian Plum
Physocarpus capitatus Ninebark
Rosa nutkana Nootka Rose
Rosa pisocarpa Peafruit Rose
Salix scouleriana Scouler Willow
Salix sitchensis Sitka Willow
Sambucus racemosa Red Elderberry
Spiraea douglasii Douglas’ Spiraea
Symphoricarpos albus Snowberry
Side Slopes
Overstory
Scientific name Common name
Abies grandis Grand Fir
Alnus rubra Red Alder
Fraxinus latifolia Oregon Ash
Thuja plicata Western Red Cedar
There are several ways to establish the vegetation in the bioswales; sodding, seeding, and
plug planting. Properly installed sod can provide immediate protection from erosion and
some immediate vegetation benefits. Reseeding of the seams between adjacent sod sec-
tions may be necessary. Soil preparation is important. After grading of the swale channel,
stones or clods greater than one-inch in diameter should be removed. The sod strips
should be laid perpendicular to the direction of flow. The sod should be rolled or tamped
after it is laid and should be secured with staples or pegs on 3:1 or greater side slopes or
in areas of high velocity flows. Seeding is accomplished by scarifying into the soil or by
hydroseeding. Seed should be irrigated carefully in order to establish a dense cover prior
to the rainy season. Some vegetation such as bunch grasses, rushes, and shrubs or trees
are most commonly planted from containers.
Trees should also be planted along bioswales that have flow year round and which dis-
charge to temperature sensitive receiving waters so that aquatic life is not adversely af-
fected. This will reduce the heat gain during the late spring, summer and early fall sea-
sons.
Page 10 of 52
15. Constructed Wetland Vegetation
Many of the grasses mentioned for bioswales may be used on the banks of the wetland
but can not be used in the wetland itself due to their low tolerance for long duration sub-
mergence.
The vegetation selected must match the expected depth of water and climate in which the
wetland is to be constructed. Native wetland vegetation for the area should be used.
Generally, grasses that may be acceptable for bioswales will not be acceptable for wet-
lands due to the submergence time and the depth of submergence being greater in a wet-
land which would overly stress the bioswale type vegetation sufficiently to kill it or ren-
der it ineffective at the time needed to remove pollutants. Consideration must be given to
where the water will come from in order to keep the wetland vegetation alive in the
summer and to the dormant cycle of the vegetation.
Vascular plants (the higher plants which grow above the water surface) and non-vascular
plants (algae) are important to a wetland. Photosynthesis by algae increases the dissolved
oxygen content of the water which affect the nutrient and metal reactions. Vascular
plants:
• stabilize substrates (soils) and minimize channel flow and open channels in the wet-
land,
• slow water flow allowing for the heavier suspended particulates to settle out,
• uptake carbon, nutrients, and metals,
• transfer atmospheric gases to the soil,
• diffuse oxygen from their subsurface structures creating aerobic biota sites within
the immediate surrounding substrate (soil),
• create microbial attachment areas on their subsurface structure, and
• create decaying material which increases flocculation and increase the biota.
The following Northwest Oregon Wetland plant list is furnished by GreenWorks P.C.
Emergent
Groundlayer
Scientific Name Common Name
Carex stipata Saw-Beaked Sedge
Carex obnupta Slough Sedge
Deschampsia cespitosa Tufted Hairgrass
Eleocharis acicularis Needle Spike-Rush
Eleocharis ovata (Common) Ovate Spike-Rush
Glyceria occidentalis Reed Mannagrass
Juncus ensifolius Dagger-Leaf Rush
Juncus oxymeris Pointed Rush
Leersia oryzoides Rice- Cut Grass
Page 11 of 52
16. Emergent
Groundlayer
Scientific Name Common Name
Sagittaria latifolia Wapato
Scirpus acutus Hardstem Bulrush
Scirpus microcarpus Small-Fruited Bulrush
Scrub Shrub
Groundlayer
Scientific Name Common Name
Agrostis tenuis Colonial Bentgrass
Carex densa Dense Sedge
Carex obnupta Slough Sedge
Deschampsia cespitosa Tufted Hairgrass
Epilobium densiflorum Dense Spike-Primrose
Juncus acuminatus Taper-Tipped Rush
Juncus articulatus Jointed Rush
Juncus effusus Common Rush
Juncus tenuis Slender Rush
Mimulus guttatus Common Monkeyflower
Potentilla gracilis Northwest Cinquefoil
Ranunculus occidentalis Western Buttercup
Saxifraga oregana Oregon Saxifrage
Scrub Shrub
Understory
Scientific Name Common Name
Cornus stolonifera Redosier Dogwood
Crataegus douglasii Black Hawthorne
Lonicera involcrata Black Twinberry
Physocarpus capitatus Ninebark
Rosa nutkana Nootka Rose
Rosa pisocarpa Peafruit Rose
Salix scouleriana Scouler Willow
Salix sitchensis Sitka Willow
Sambucus racemosa Red Elderberry
Spiraea douglasii Douglas’ Spiraea
Page 12 of 52
17. SCRUB SHRUB
Overstory
Scientific Name Common Name
Abies grandis Grand Fir
Alnus rubra Red Alder
Fraxinus latifolia Oregon Ash
Thuja plicata Western Red Cedar
Bulrushes are very tolerant of high nutrient levels.
Several planting methods may be used to plant the wetland. The use of nursery starts is
best as they are more likely to establish and prosper that seeding and there is less invasive
vegetation establishment. Five to seven plant species should be selected with three which
are aggressive and that can establish rapidly. The plantings should be made during the
growth season. After excavation of the wetland, the excavation should be kept flooded
until planting occurs. Before planting the excavation should be drained and checked for
the appropriate depth zones for the plants to be established. Different species should be
planted in zones and not mixed so that the take over of a particular species can be mini-
mized.
Soluble forms of phosphorus as well as ammonia are partially removed from storm water
runoff by planktonic and bethic algae. Algae consume nutrients and convert them into
biomass, which then settles to the bottom of the wetland providing the material for the
uptake needed by the vegetation for sustainable growth.
Trees should be planted around the wetland to reduce the heat gain and the warming of
the water, which may adversely effect aquatic life downstream from the wetland.
Assistance should be obtained in the selection of the vegetation from a wetlands biologist
and/or from the local NRCS Field Office (http://or.nrcs.usda.gov). A program called
VegSpec is available on the internet at http://www.nrcs.usda.gov/technical/efotg/ in sec-
tion IV.C. Technical Resources of the Field Office Technical Guides, that may be helpful
in selecting the vegetation. The soil type is required to use this program. The specific
soil type does not necessarily have to be that which you have but something similar in the
list to that which you have is necessary.
Page 13 of 52
18. Bioswales
Bioswale is the term generally given to any
vegetated swale, ditch, or depression that con-
veys storm water. The fully vegetated
bioswale and the open channel bioswale
(roadside example at the right) are the two ba-
sic types of vegetated swales based upon the
degree of vegetation. Some subtypes of
bioswale are based upon their general cross-
sectional shape, i.e. “U”, “V”, and “trape-
zoid”. Generally, the “U” and “V” shaped
swales are just ditches that have become natu-
rally vegetated and they are usually open
channeled. The Trapezoidal fully vegetated
bioswale is the most effective bioswale at re-
moving pollutants. Open channels do not add
much more than infiltration to the process of
removing pollutants. When bioswales are de-
signed, they are designed to address a certain
storm event such as the two year or ten year
24-hour storm event. Statistically, around 90
percent of the storm events will be less than
this design amount. Open channels typically are open to the extent that this 90 percent
flow is in the open channel which results in very little bioremediation of the storm water
most of the time. Fully vegetated, trapezoidal cross-section bioswales will result in much
better remediation of the pollutants in the storm water runoff than open channels or the
other cross-sections.
Trapezoidal Cross Section Example
Bioswales provide good treatment of stormwater runoff without the extensive mainte-
nance required for some other stormwater BMPs. Pollutant removal rates increase when
bioswales are well maintained, and as the residence time of water in a swale increases.
The effectiveness of bioswales is also dependent upon the retention time of the storm wa-
ter in the bioswale. The longer the retention time, generally, the higher the removal effi-
Page 14 of 52
19. ciency. The type of vegetation and the life cycle that the vegetation is in will also effect
the pollutant removal rate. Consultation with a biologist is greatly beneficial when con-
sidering what vegetation to plant in the bioswale. Dormant vegetation will only reduce
the storm water runoff velocity and not provide the benefits of vegetation uptake of the
pollutants. Some reduction in the bacterial uptake and conversion of pollutants to more
stable less toxic configurations will still take place but probably at much reduced rates.
Stormwater runoff contributes pollutants to streams, rivers and lakes. Pesticides, herbi-
cides, and fertilizers come from residential lawns, commercial landscaping, and recrea-
tional facilities like golf courses. There can be residuals that leach from land that was
once farmland. Heavy metals come from vehicles, buildings, roofs, and industrial sites.
Oil and grease drip regularly from cars onto streets, parking lots, and are occasionally
dumped into storm drains by residents performing maintenance on vehicles and equip-
ment. Pathogens and bacteria in runoff can come from pet waste, broken or leaking sani-
tary sewers, wildlife, or sanitary sewer overflows.
Bioswales can remove and immobilize or break down a large portion of pollutants found
in stormwater runoff. Bioswales have achieved high levels of removal of suspended sol-
ids (TSS), turbidity, and oil and grease. They can also remove a moderate percentage of
metals and nutrients in runoff. This lower level of removal compared to sediment or oil
and grease is due partly to the large percentage of metals and nutrients that appear in dis-
solved form in runoff. The term “dissolved form” includes microscopic particulate that
generally is referred to as turbidity.
Bioswales can achieve good removal of metals or nutrients that are attached to suspended
soil particles through settling of the solids by natural flocculation and vegetation uptake.
Infiltrated storm water uses the soil and, in some cases depending upon the pollutant, the
microbiology in the soil to filter dissolved pollutants from runoff. Since most bioswales
infiltrate only a portion of their flow, removal rates for pollutants in dissolved form are
lower than those for sediment or oil and grease unless retention time for the pollutants in
the bioswale is sufficient for natural flocculation, infiltration, biological conver-
sion/consumption, and/or vegetative uptake to occur.
Nutrients, including nitrogen and phosphorus, appear in urban runoff in dissolved form as
well as attached to sediment particles, and can be removed by settling, flocculation, vege-
tation uptake, and infiltration. They are then broken down or converted to other forms by
the biota, and are stored in the soil or taken up by plants. Nutrient remobilization can oc-
cur in the winter when plants become dormant or if the soil is transported. However, pe-
riodic mowing of swales and removal of the mowed vegetation can reduce remobiliza-
tion.
Like nutrients, metals appear in both dissolved form and attached to sediment particles.
Metals removal rates by swales can be maximized by:
* maximizing the amount of water captured by a swale through infiltration;
Page 15 of 52
20. * increasing the pH of a bioswale's flow--basic flows drop out more metals;
* increasing the cation exchange capacity and pH of the bioswale's soil (soils with
more organic matter remove a greater amount of metals); and
* maximizing the density of a bioswale's vegetative cover without unduly restricting
the flow.
Metals reduction concentrations ranging from twenty to sixty percent in the storm water
runoff have been documented in studies of bioswales. The higher reduction values were
common for well-designed and maintained swales, and the lower reduction values were
seen for swales with patches of bare soil or short retention times.
Since much of the metals removal ability of bioswales has been related to infiltration, an
important concern is whether the heavy metals will accumulate to toxic levels in the
bioswale underlain soil and whether they will migrate into and contaminate the ground-
water. In removing heavy metals either through vegetation uptake or through soil filtra-
tion, a bioswale concentrates them. Maintenance of the bioswale vegetation by mowing
or removing dead vegetation will remove some of the accumulated metals. Soil particles
will attract and bind much of the remaining concentrations of the metals. Studies of
bioswales in sandy, loamy, and clayey soils, found that in many cases metals accumu-
lated only in the top several inches of soil. In clayey and loamy soils showed metals ac-
cumulating only in the top two inches of soil.
Some people consider the filtration of the storm water through the soil as being one of the
largest benefits to using bioswales. Experience dealing with septic systems indicates that
there can be a limit to the amount of filtration that can be obtained by the soil in filtering
out and retaining some pollutants. The degree of the soils ability to continually remove
some pollutants depends to some extent on whether or not the pollutant is biologically
degradable.
Metals have not been found to accumulate to toxic levels in grassy swales. One study in
1986, of a bioswale adjacent to a four-lane high-way carrying 29,000 vehicles per twelve
hours fifteen years after its construction, showed metals levels in the grassy bioswale
were far below the required standards for metals in municipal wastewater sludges rec-
ommended for agriculture usage, with the exception of lead, which was at the standard.
The lead probably came from the use of leaded gasoline in that time frame. With the
elimination of leaded gasoline since that time, concentrations of lead in swales con-
structed in the last few years would probably not be as high as that measured in the par-
ticular study.
Biologic action accounts for the high removal of oil and grease from swales. A minimum
seventy-five percent reduction of oil and grease was found in one study in a bioswale
with a residence time of approximately 9 minutes. A check of the length of the same
bioswale equivalent to a residence time of four and a half minutes resulted in a minimum
oil and grease removal of forty-nine percent. It has been found that, to a certain extent
Page 16 of 52
21. and with a small lag time, as the concentration of oil and grease increase the removal ef-
ficiency increases. The lag is probably due to the time required for the establishment of a
additional new growth of bacteria and the increased efficiency was probably due to the
increased bacteria present.
In the few studies that have been done on pathogen removal by swales, grassy swales
have not been found to significantly reduce concentrations of escherichia coli (e. coli)
bacteria. This could be due to the fact that swales attract more wildlife which add to the e.
coli in the swale. There is no conclusive information as to whether swales will or will not
remove pathogens.
Besides removing pollutants from storm water runoff, bioswales provide storm water de-
tention and thus can reduce the increased peak flow rate that is the result of increased im-
pervious surfaces from site development. Many municipalities in Oregon are now requir-
ing water quality or detention ponds or devices to mediate the expected increased peak
flow rates from development and thus reduce or eliminate increased stream flows which
typically cause stream bank erosion. Bioswales can be an alternative to those detention
facilities.
Vegetation
Swale vegetation must meet certain criteria for the vegetation planted along a swale to
maintain channel stability and improve the bioswale's ability to filter pollutants from
stormwater. The vegetation must:
* provide a dense cover and a root or rhizome structure that holds the soil in place in
order to resist erosion;
* during water quality level flows (event design), it must stand upright in order to
provide maximum residence time and pollutant removal;
* tolerate a bioswale's soil conditions (pH, compaction, composition); and
* tolerate periodic flooding and drought. It must not be dormant during the period of
the year that the pollutants are to be treated.
In some cases, the bioswale vegetation must also meet aesthetic and functional criteria by
selecting the appropriate plant for the use, water cycle, aesthetic goals, and local govern-
ment codes. Many municipalities require setbacks from intersections, require low height
vegetation for visibility at intersections, along parking lots, streets, and pedestrian walk-
ways, or for police surveillance. Bioswales and their plant materials can present unique
and different visual characteristics from conventional drainage or landscape design. Turf
grass lawns, woody perennials, drought-tolerant, riparian or exotic plants, and cobbles
can all be used, depending on the desired aesthetic effect.
Page 17 of 52
22. BIOSWALE DESIGN
In areas were there is insufficient land length available to obtain the retention time neces-
sary in order to gain the maximum effect of a bioswale, it is better to install a bioswale in
conjunction with some other treatment system such as a sand filter for whatever pollution
removal that can be accomplished than to not install one. Bioswale design parameters to
consider are: settling pond or chamber at the inlet; excess runoff considerations; cross-
section selection; swale slope; swale width; swale vegetation selection; level spreader
use; storm design event; flow velocity; vegetative bed compaction and porosity; and con-
struction season for the bioswale.
Design Event and Runoff Expectations:
The most polluted runoff usually occurs during the first portion of a storm cycle. The
oils, metals, and other pollutants accumulated over a dry period are washed off rooftops,
roadways, and other surfaces in the first light rain or in the first minutes of a large storm.
In subsequent storm cycles this pattern is repeated, with the first rains carrying the high-
est concentration of pollutants. The term usually associated with this phenomena is “first
flush”.
The first consideration to make is what storm event the bioswale should be designed to
handle. Serious consideration should be made of the degree that site construction has
compacted the soils and the type of soils present on the site. A design guide developed
by the US Department of Agriculture Natural Resource Conservation Service called TR-
55 can be of assistance in calculating the amount of runoff from a site for a given rainfall
event. TR-55 can be downloaded from the internet web site at:
http://www.wcc.nrcs.usda.gov/water/quality/common/tr55/tr55.html. For some sites, es-
pecially heavy clay or heavily compacted sites and long duration storm events, designing
the swale for 100% runoff may be the best conservative approach to use. Both the peak
and design duration storm events should be investigated. The two-year 24-hour storm
event should be the minimum that the bioswale is designed to treat. A map of the Oregon
two-year 24-hour storm events can be found on the internet at:
http://www.wrcc.dri.edu/pcpnfreq.html. Check with your local government to see
whether or not they have a different design storm event in their codes. The storm peak
runoff will be higher than the 24-hour average. A metered water quality or detention
pond at the head of the swale could serve as the sedimentation pond and as a means of
controlling the flow rate to the swale.
In the past, stormwater management has focused almost exclusively on flood protection
through the use of water quality or detention ponds. Systems that can accommodate these
peak flows are more than adequate to convey small storms, which occur much more fre-
quently. So, the small storm and its impacts are often overlooked. Yet, small storms, be-
cause of their frequency and cumulative impacts, make the largest contribution to total
annual runoff and have the greatest impact on water quality. For this reason, stormwater
design must consider both the peak volumes for flood control, as well as the water quality
volume for pollution control.
Page 18 of 52
23. The water quality volume (24-hour design storm) is usually established by local or re-
gional agencies and varies depending on local conditions. It is defined as the amount of
runoff that must be treated before being released into a conveyance storm drain network
or receiving water.
The Water Environment Federation/American Society of Civil Engineers in their jointly
published Urban Runoff Quality Management (1998) adopted an eighty percent annual
capture rate as a standard of practice for water quality volume. This translates into ap-
proximately the first one-half to one-and-a-half inches of rain depending on annual rain-
fall and local rainfall patterns. It can also be translated as a two-year recurrence interval
storm, or the size storm that has a fifty percent chance of occurring in any given year.
The Center for Watershed Protection, recommends a ninety percent annual capture rate.
Under this rule, grassy swales are sized to treat ninety percent of the annual volume of
runoff in a watershed.
The bioswale inlet can be designed to allow peak flows to bypass the bioswale and be
conveyed by a conventional conveyance system. This also prevents the larger, higher
velocity flows of large storms from washing out any accumulated sediment or eroding the
vegetation in the bioswale. To determine the appropriate design storm for a particular
area, consult local rainfall data or contact a local municipality or flood control, public
works, or stormwater agency for the required standard. While the design storm is typi-
cally expressed as a depth, the associated rainfall intensity is also required to design the
channel cross section. The bioswale will treat runoff only as fast as it arrives at the swale,
and this is governed by how much rain falls on the ground over a given period of time,
how much evaporation takes place, and how much infiltration occurs.
Bioswales are usually a part of a larger storm drainage system that drains water from de-
veloped areas. They must also be sized to convey a peak flow design storm without erod-
ing. The design storm is often the two-year, five-year, or ten-year, twenty-four-hour
storm, although municipalities may have adopted other standards for their swales or open
channels. As with the water quality design storm, the local municipality, planning de-
partment, flood control, public works, or stormwater agency will provide the required
standards.
When designing a swale to handle a certain storm event occasionally a storm event of
grater volume than the design event will occur and result in the runoff overflowing the
swale. Some thought should be given to measures that can be taken to reduce the prob-
lems such overflow would create. These measures might be to temporarily provide for
overflow onto adjacent parking areas or landscaped areas adjacent to the swale. Another
method would be to design an overflow system to accommodate the excess flow directly
into a storm sewer.
Page 19 of 52
24. Geometric Design Principles
The basic components of bioswale design include: longitudinal slope, cross section
(shape), length, and roughness. Roughness is a function of the vegetation coverage and
type.
Longitudinal Slope
The longitudinal slope of a bioswale is a critical design element that effects the design of
the bioswale and its performance. Appropriate slopes typically range from one percent to
six percent.
The optimal longitudinal slope of a bioswale is between one and two percent. Low slopes
limit erosion by reducing water velocities and increase pollutant removal by increasing
residence (contact) time of water in the swale. As longitudinal slope and velocity in-
crease, erosion may increase and pollutant removal rates typically decrease.
On slopes less than or equal to one percent, drainage is marginal, and standing water may
be present if the underlain soil type does not allow much infiltration or the water table
remains high. Perforated drain pipe can be installed in the bottom of the bioswale to al-
low for this drainage. It might be useful to install a valve on the drain pipe near the down
gradient end of the piping so that the ponded water may be drained as required. The rea-
son for this is that excess draining of the bioswale bottom will deplete needed water re-
serves that are necessary for the vegetation through the dry summer months which would
require more frequent irrigation for the vegetation to be active at the beginning of the wet
season.
Bioswales are not recommended on slopes
greater than six percent unless they can
somewhat follow the slope contour to limit
the swale slope to less than six percent.
Page 20 of 52
25. Bioswales with longitudinal slopes of from two to six percent require check dams or
weirs spaced approximately every fifty to 100 feet along the length of the bioswale to re-
duce the speed of flow. Check dams reduce velocity, increase residence time, protect
plant material from erosion, and enhance pollutant removal.
Swale Cross Section (Shape)
There are four basic cross sections for bioswales: rectangular, triangular, trapezoidal, and
parabolic. Trapezoidal cross sections are the most common shape for bioswales because
they are easy to construct, offer good hydraulic performance, facilitate maintenance, and
are aesthetically pleasing. Triangular cross sections can also be appropriate if the side
slopes are very gentle (approximately 10:1 or shallower). Rectangular cross sections are
generally not used for grassy swales because they are difficult to construct and maintain,
difficult to establish with vegetation in the sides, and because the vertical side slopes can
present a safety hazard.
In general, shallow side slopes are more desirable, although they increase the amount of
area required for the bioswale. A 3:1 slope (horizontal:vertical) is considered the steepest
to limit erosion and/or slippage of the slopes. A 5:1 slope is considered the steepest slope
that allows regular mowing.
Bottom Width
A wide, flat swale bottom maximizes the available treatment area and pollutant removal
while also providing ease of maintenance. In order to be able to mow the vegetation in a
bioswale, the bottom should be at least two feet wide. The maximum free width of the
bioswale bottom should be less than eight feet wide to avoid rilling and gullying and en-
sure sheet flow.
Depth
The bioswale should be at least six inches deeper than the maximum design flow depth.
This additional depth is known as "freeboard," and provides a safety factor to prevent the
bioswale from overflowing onto adjacent areas if the channel becomes obstructed or if
runoff volumes exceed the design size.
Length
The time it takes water to flow from its inlet into the bioswale to the bioswale's outlet is
the “residence time” or retention. Residence time for bioswales should be at least five
minutes. The designer should seek to maximize a bioswale's length, since this will in-
Page 21 of 52
26. crease the residence time, or “contact time” of runoff with the vegetation in the bioswale.
In general, the greater the residence time, the greater a bioswale's ability to remove pol-
lutants from runoff.
Water Velocity
The speed at which water flows in the bioswale is its velocity. Velocity is calculated for
two storm sizes: water quality design storm and the peak flow design storm. Velocity
should be less than or equal to one-and-a-half feet per second for the water quality design
storm, and below five feet per second or the erosive velocity of the channel for the peak
flow design storm. This is generally three to six feet per second depending on vegetation
type and the use or erosion control fabric or other stabilization method. Erosion may be a
problem if average discharge velocities frequently exceed three feet per second. Where
velocities make erosion a concern, erosion control fabrics or geotextiles may be used to
achieve added erosion resistance while still allowing the growth of a dense stand of vege-
tation.
Inlet
An inlet method of directing water into a bioswale that is commonly seen is to provide
for continuous inflow along the entire length of the bioswale (sheet flow). This is easy to
achieve by eliminating curbs next to streets and parking lots. In this way, inflows are
spread over a wide area, erosion is minimized, and pollutants are dispersed widely among
the vegetation. One of the draw backs with this is that the residence time for the storm
water entering the bioswale is not maximized. If the flow is evenly distributed along the
full length of the bioswale then the average residence must be figured from the center of
the length of the bioswale to the discharge point.
When a concentrated inlet such as a pipe or curb cut is used, an energy dissipater and
flow spreader should be used where the water enters the bioswale to rapidly spread the
flow over the full width of the bioswale. This will limit erosion, maximize the bioswale
pollutant removal efficiency, and reduce the need for maintenance.
The asphalt edge of a street or parking lot that drains directly into a bioswale may crack
over time due to plant growth or occasional car traffic. To avoid this problem, a concrete
or stone band (or other hard edge) can be placed to finish the asphalt edge. The top of the
band should be at the grade of the asphalt to allow for water to pass over the band and
into the bioswale.
Check Dams/Weirs
Check dams, or weirs, pool water upstream of the weir, increasing residence time and
infiltration. A number of check dam designs have been implemented in the field, includ-
ing notched concrete weirs, board check dams, and stone check dams. Check dams
should include an orifice for very low flows and to minimize long-term ponding that may
foster mosquito growth.
Page 22 of 52
27. The frequency of placement and design of check dams should be governed by longitudi-
nal channel slope and geometry. To obtain maximum storage from stable check dams,
they should be located such that the upstream limit of ponding from one check dam is just
below the downstream edge of the adjacent check dam. To prevent mosquito develop-
ment, check dams should be designed to pond water to a depth that will infiltrate within
twenty-four hours of the end of a storm. Infiltration testing prior to construction of the
bioswale will be helpful in determining whether or not there is likely to be a problem in
this area. An underdrain (French Drain) system may have to be installed with valving to
control the ponding.
CONSTRUCTION
During construction, the soil in the bottom and sides of the bioswale have typically be-
come compacted and may be deficient in many of the basic elements necessary to provide
the optimal growth of the vegetation to be planted. The soil in the bottom and sides of
the bioswale should be prepared before the vegetation is planted. Preparation of the soil
should include tilling in additives such as grit in the form of sand and gravel, or ceramic
grit, and/or compost to reestablish infiltration capability and, in the case of compost, or-
ganics for vegetation growth and reestablishment of voids for air.
Ceramic Grit Installed in Bioswale
If sand and gravel or ceramic grit is
used, some form of nutrients and organ-
ics must be added to recreate topsoil.
Typical mixture ratios for mixed-yard-
debris compost should be around 1:3
compost to existing soil. Compaction of
the soil from construction can extend to
a depth of thirty inches or more depend-
ing on soil type and moisture content.
So whatever method is used to recreate
the natural infiltration rate should ex-
tend at least twelve to twenty-four
inches into the bioswale bottom and sides. See the article on compost on the Oregon
DEQ web page at http://www.deq.state.or.us/nwr/stormwater.htm for more in-
formation on soil compaction and compost. Caution should be exercised if plug planting
and fertilization are used instead of complete bioswale bed preparation. This practice can
result in localized subsurface water ponding and associated root rot, and/or restricted root
growth and root ball formation which will eventually result in loss of much of the vegeta-
tion planted.
It usually takes at least two years to effectively establish the bioswale vegetation unless
compost amendment of the subsurface soil occurs. This means that to prevent erosion
and loss of vegetation during the first year, some method must be used to protect the
seeds, if seeding is used, other vegetation planted, and provide for the soil isolation and
Page 23 of 52
28. armoring from the water flow. The use of biodegradable geotextiles laid over seeds or
the use of a liner through which vegetation can grow from the top down will provide the
necessary isolation and armoring needed. The main ingredient needed to provide the iso-
lation and armoring is complete soil coverage and good anchoring of the material. A
tight weave jute mating has proven effective in use for this isolation and armoring as has
a new material being used by Hobbs & Hopkins as part of their Bioswale System.
Jute Geotextile Mat Bioswale System Liner
Erosion control fabrics are usually classified into mulches; organic, biodegradable, and
non-biodegradable blankets and netting; and soil-filled turf reinforcement mats. The use
of tackified mulches should only be considered for low-velocity swales or bioswales
planted early in the summer and irrigated for vegetation establishment. Note that
mulches will add to the nutrient load in the bioswale until it is consumed and may be sub-
ject to increased erosion until the vegetation is fully established.
Erosion control blankets and netting can be made completely of or in combinations of
jute, coconut fibers, straw, excelsior, and various plastics, and are usually installed sta-
pled or staked into the ground or weighted down with rock or gravel. A seed mixture
may be installed in the mat or they may be installed over the seed. Biodegradable blan-
kets or nets degrade thus stabilizing the swale over the short term but providing no long-
term protection.
Turf reinforcement mats (TRMs) are flexible, synthetic mats filled with soil. They pro-
vide long-term channel and vegetation stabilization at velocities in the range of fourteen
to twenty feet per second.
The following are common problems encountered during construction which result in
problems for the best effective bioswale vegetation establishment.
• Crews unfamiliar with the concept behind bioswales;
• timing of the construction of the bioswale is delayed;
Page 24 of 52
29. • compaction of the bioswale subsoil and subsequent failure to correct the prob-
lem;
• poor timing of bioswale construction, such that the bioswale is inundated with
sediment-laden runoff, seeding is washed off by the first rains, or erosion occurs
in the bioswale and turbidity laden waters are discharged ;
• cost cutting occurs in the selection and planting of the vegetation; and
• poor preparation of the swale channel to accept flows, i.e. check dams are not in-
stalled.
The construction period is also typically the period when greatest erosion occurs. If a
swale is located downstream from a construction site, it may collect sediment from the
site. This is an indication of how effective the swale is--sediment that settles in the swale
is sediment that does not flow off-site into receiving waters. Prior to the completion of
construction, sediment can be excavated from the swale and redistributed as topsoil on-
site.
Water Quality Effect: Monitoring and Performance
There are two ways of measuring the effectiveness of bioswales at removing pollutants.
The first is by measuring the particular pollutants of interest by their concentrations in
water entering and exiting the bioswale and calculating the difference. This method does
not account for the infiltration of the pollutants along the length of the bioswale which
may be released at some future time or have to be remediated in the future. The second
method involves performing a mass balance of pollutants in the bioswale throughout the
length of the bioswale. This method will result in information on the amount of pollut-
ants retained in the soil and vegetation of the bioswale.
Obtainable Efficiencies:
Obtainable reductions of pollutants in bioswales are:
Total Suspended Solids – 83 to 92%
Turbidity (with 9 minutes of residence) – 65%
Lead – 67%
Copper – 46%
Total Phosphorus – 29 to 80%
Aluminum – 63%
Total Zinc - 63%
Dissolved Zinc – 30%
Oil/Grease – 75%
Nitrate-N – 39 to 89%
These results can be obtained for a bioswale at least 200 feet in length with a maximum
Page 25 of 52
30. runoff velocity of 1.5 ft./sec., a water depth of from one to four inches, a grass height of
at least 6 inches, and a minimum contact (residence) time of 2.5 minutes.
Maintenance
Although through proper vegetation selection a bioswale may be relatively low mainte-
nance, some bioswales may require regular plant maintenance for aesthetic reasons. This
maintenance includes regular mowing, irrigation, and pruning. Mowing or cutting back
the vegetation also reduces evapotranspiration and reduces the amount of pollutant up-
take until the vegetation reestablishes full growth.
Vegetation in the bioswale should be trimmed every year or two to prevent woody spe-
cies from taking over. Clippings from plants should be disposed of properly as they may
have absorbed hazardous toxins. Removal of vegetation clippings following this practice
removes pollutants that have been absorbed by the vegetation. Fertilizers and herbicides
are a source of organic compounds which are some of the pollutants that are removed by
the vegetation in a bioswale and their use for maintenance of the bioswale should be
avoided as much as possible.
Regrading may be necessary to reshape the bioswale cross-section as sediments collect
and form pools. As with plant waste, sediments should be removed and disposed of
properly.
Regular maintenance activities for bioswales should include inspection of surface drain-
age systems to ensure removal of any sediment buildup and trash; repair of surfaces that
have been damaged by erosion, rodents, vehicles or other causes; care of plant materials;
replacement of dead plants; and regular irrigation during dry periods. Inspections and
repair to bioswales should be scheduled far enough in advance of the first seasonal rains
to allow for any repairs that may be necessary, and during and after each major storm.
Trash and debris left to accumulate in either the storm drainage system leading to the
bioswale or in the bioswale can restrict the flow of water causing localized flooding and
possible erosion, create sediment buildup, and create aesthetic problems that create poor
public perception of the site.
Page 26 of 52
31. EXAMPLES
HOBBS & HOPKINS BIOSWALE SYSTEM
Swale with ceramic grit installed. Swale with erosion/turbidity protection
blanket and Check Dams installed.
Swale with seed/mulch being applied on
top.
Bioswale with emerging vegetation.
Page 27 of 52
32. PARKING LOT BIOSWALES
Oregon State Police Department Parking Lot Mini
Bioswales- Portland
Oregon Museum of Science and
Industry Parking Lot Mini
Bioswales - Portland
Page 28 of 52
33. Oregon Museum of Science and Industry Parking Lot Mini Bioswales – Portland
Portland Community College Parking
Lot Mini Bioswale
Page 29 of 52
34. GRASSY BIOSWALES
Lawn Bioswale in Texas Spokane Park and Ride Lawn Bioswale
Reed College – Portland SW Scholls Ferry Road – Portland
Page 30 of 52
35. Residential Development Grassy Bioswale at Fairview Lake
used during subdivision construction
COMMERCIAL BIOSWALES
City of Portland
Bureau of Environmental
Services Laboratory Bioswale
– St Johns
Gifford Pinchot National Forest Head-
quarters Bioswale
Page 31 of 52
36. Washington County Commercial Development Bioswale – Beaverton
Spring at end of first year above and Fall of the same
year at right.
Page 32 of 52
37. RURAL BIOSWALES
Within one year of construction Three years after construction
Hawthorn Ridge next to SE 162 Avenue - Portland
Center for Urban Horticulture Bioswale - Seattle
Gresham Bioswale
Page 33 of 52
38. School Bioswale
Parking Lot Mini Bioswale Wide Main Bioswale
Arrata Creek School
9821 Arrata Place, Troutdale
INDUSTRIAL BIOSWALES
Kinzua Resources, L.L.C. – Pilot Rock, Oregon
View looking south toward the outfall View looking North from the outfall
Storm water runoff from this lumber company drained off the impervious surfaces to a
low area and then ran off to Birch Creek. The runoff, prior to the construction in 2000, of
the nearly 400 feet long bioswale was high in Total Suspended Solids (190 - 810 mg/l)
and zinc (0.011 - 0.86 mg/l). After the bioswale construction, initial testing show that the
TSS has been reduced to between 26 and 100 mg/l and zinc has been reduced to blow 0.1
Page 34 of 52
39. mg/l. Prior to construction of the bioswale there was always runoff from one of the two
preexisting outlets even during light, short duration rainfall events. Now there is minimal
runoff out of the one final outfall.
Weyerhaeuser Warrenton Log Yard
Naturally vegetated drainage ditches prior to bioswale construction
Construction of bioswale in 2001
(Notice swale divider in picture on the right)
Page 35 of 52
40. Bioswales approximately 1 year later
STREET RUNOFF BIOSWALE
At Construction in 2001 One Year Later
On Baseline Road at Beaverton Creek
Page 36 of 52
41. Phytofiltration
In this document, the term “Phytofiltration” will be used to refer to the use of vegetation
uptake of pollutants in storm water runoff in vegetated strips rather than in bioswales or
constructed wetlands. There is no excavated channel although the area under considera-
tion will slope to an outlet. The flow across the vegetated strip will be in sheet flow and
the vegetation will typically not be a wetland species.
The picture above shows a mostly impervious 11.5 acre industrial site (Fought & Com-
pany Inc.) with a 195,750 square feet galvanized corrugated roofed building. The zinc
levels in the storm water discharge ranged from 4.31 mg/L to 9.13 mg/L from the roof
with a permit benchmark of 0.6 mg/L. Cleaning and painting the roof is an option that
would have a significant cost. The site chose to divert all of the roof runoff to one catch
basin and use vegetation to remove the zinc. The amount of space required for this was
so insignificant that the area which is located next to the building just in from the lower
left hand corner of the above picture does not show very well in the above picture.
An area approximately twenty feet wide by thirty feet long was prepared by removing the
asphalt and adding a mixture of sand (70%) and porous ceramic grit (25%) along with a
microbial nutrient to a depth of 8 inches. A grassy vegetation seed mixture from Hobbs
& Hopkins, Pro-time 705 PDX Ecology Lawn Seed Mixture, was applied. On the pe-
ripheral of the area troughs were installed with level outfall edges to the grassy area to
encourage sheet flow to the catch basin.
Page 37 of 52
42. The vegetation must be watered in the summer and maintained by cutting an removal of
the grass to a composting facility so that the zinc will not continue to build up but be re-
moved.
Catch Basin
Level Spreader Trough
Testing for the last two years shows the zinc discharging into the catch basin is now rang-
ing from 0.05 mg/L to 0.34 mg/L, an approximate 97% reduction.
This Phytofiltration makes use of the biological microorganisms which convert the zinc
into a form which is readily acceptable to the vegetation for uptake.
Other pollutants can be removed using this method of filtration. A couple of things need
to be considered in the construction of a filter strip.
a. The longitudinal slope should be 2% or more and groundwater needs to be below
the vegetation root depth unless the vegetation specifically can withstand the con-
stant water at the roots.
b. The filter strip should be located in an unshaded area of the site.
Page 38 of 52
43. Constructed Wetlands
Constructed wetlands are man-made, engineered wetland areas created through excavation
and/or berming. They typically differ from natural or restored wetlands in that they are
located in areas where no wetland existed before. The regulatory status of constructed
wetlands is unique in that they can be created, used, and eliminated generally without
permits or other regulatory input with the exception of possibly land use regulations. The
basic types of constructed wetlands are shallow marsh, 2 or 3 celled pond/marsh, ex-
tended-detention, and pocket wetland. Extended-detention and pocket wetlands are less
effective in removal of some types of pollution than other types of wetlands either as a
result of the open channel or the reduced retention time of the storm water. They are par-
ticularly good for the removal of nutrients and conventional pollutants such as oil and
grease and some heavy metals. Constructed wetlands can be classed as either surface
flow, subsurface flow, or hybrid systems, which are a combination of both.
Surface flow wetlands have the water level and flow above the ground surface and vegeta-
tion is rooted and emerges above the water surface. The near surface water layer is aero-
bic while the deeper water and substrate are usually anaerobic. Subsurface flow wetlands
have the water flow below the surface of a sand and gravel bed in which the roots of the
vegetation penetrate to the bottom of the bed. Subsurface wetlands are frequently used to
lower the 5-day biochemical oxygen demand (BOD5) which causes reduced oxygen levels
in the storm water runoff. Subsurface wetlands provide greater attachment surface area
for biota and may treat storm water faster and thus promote smaller constructed wetlands
for the same level of treatment.
Wetlands designed for sediment and turbidity removal also serve as mechanisms for re-
moval of phosphorus and pesticide removal. Phosphorus and pesticides are absorbed and
attached to soil particles that enter the wetland.
Constructed wetlands have been used to some extend for the secondary or tertiary treat-
ment for sewage treatment where they are very cost and performance efficient at remov-
ing nutrients, suspended solids, metals, and other pollutants. The life of this type of
treatment wetland can be as long as 20 years. To date, constructed wetland life for treat-
ment of storm water is unknown but should with minimum maintenance exceed the life
of a wastewater treatment wetland. The following discussion will focus on the use of
constructed wetlands for the treatment of storm water.
Since maintaining water in the constructed wetland is so important, constructed wetlands
should not be built in well draining (type A) soil unless a liner is used or a method of
providing off season water to keep the wetland viable are considered. Use of a liner
would minimize water loss to infiltration but also give up any potential pollutant benefit
to that in filtration. This is desirable in some areas especially where the depth to the wa-
ter table is great in the summer and a source of summer or dry weather supplemental wa-
ter is lacking or difficult and costly to obtain. If a liner is to be used, the soil above the
wetland must be carefully constructed to provide the growth medium for beneficial biota
Page 39 of 52
44. and for initial organics and nutrients for vegetation establishment.
Providing that the water does not freeze, wetlands can perform sedimentation in cold
weather. Wetland substrate, where decomposition and microbial activity occurs, can
generate sufficient heat to keep the subsurface layers from freezing. The rate of decom-
position will slow as the temperature drops so if the wetland is needed to perform during
cold weather it may be necessary to created a larger constructed wetland for this condi-
tion. Wetlands will lose large amounts of water in the summer to evapotranspiration. If
there is too great a vertical distance between the root zone of the vegetation and the
ground water level in the summer, a liner will be needed to minimize the loss of water to
infiltration and a source of water during this time may be needed in order to provide for
the survivability of the wetland vegetation.
Basic Design and Construction:
• Suitable for larger sites, up to 100 acres.
• Shape should be long and relatively narrow. A length to width ratio of 5:1 is pre-
ferred, with a minimum ratio of 2:1 to enhance water quality benefits. The longer
length allows more travel time and opportunity for infiltration, biofiltration and
sedimentation.
• Soils should be tested to determine suitability. Best when located in clay loams,
silty clay loams, sandy clays, silty clays and clays.
• For storm water, the permanent pool depth should be not more than 18 inches deep.
This depth is a function of the selected vegetation’s ability to grow and thrive in the
water depth.
• Cannot be used in areas with shallow depth to bedrock or unstable slopes.
• Needs to have a shallow marsh system in association to deal with nutrients.
• Should be multi-celled preferably three of equal sizes, the first cell should be 3 feet
deep to trap coarse sediments and slow turbulence (settling basin or pond). They
need to be designed as a flow through facility, and the pond bottom should be flat to
facilitate sedimentation.
• Side slopes should be 2:1, not steeper than 3:1, and 10 to 20 feet in width.
• Pond berm embankments over 6 feet should be designed by a registered engineer.
Berm tops should be 15 feet wide for maintenance access and should be fenced for
public safety.
• Baffles can be used to increase the flow path and water residence time.
• Should have an overflow system/emergency spillway to deal with a 100 year 24-
hour flood, and a gravity drain.
• Access to the wet pond is to be limited with a gate and signs posted.
• For mosquito control either stock the pond with fish or allow it to be drained for
short periods of time (do not kill the marsh vegetation). Full vegetation with no
clear or open water tends to eliminate or at least restrict mosquito populations.
• Selection of vegetation should be done by a wetland specialist. Three to eight dif-
ferent types of vegetation should be used.
• Oil/water separators can be used prior to the constructed wetland depending upon
Page 40 of 52
45. the surrounding land uses. Generally this is not necessary as the vegetation tends to
break up and consume oil and grease.
• Relatively low maintenance costs.
Design Considerations:
Characterize the quantity and quality of the storm water runoff to be treated by sampling
the storm water prior to designing the wetland and modeling the runoff and rainfall data.
• Constructed wetlands have larger land requirements for equivalent service com-
pared to wet or water quality detention ponds.
• Relatively high construction costs.
• There is a delayed efficiency until plants are well established (1 to 2 seasons).
• Need a buffer width of 25 to 50 feet.
• Water level fluctuations can kill plants so water level control is a must.
• A sediment pond on the inlet is needed to remove sediments prior to the wetland
and thus decrease wetland sedimentation and maintenance costs
• An inlet flow distribution system is needed to enhance maximum wetland effi-
ciency.
• A flow discharge system is needed to ensure that flow across the full width of the
wetland is discharged evenly and thus ensure maximum wetland usage.
• May have to be excavated to the water table to ensure dry season water source.
• Full vegetation with no open channels is needed to maximize efficiency and dis-
courage waterfowl usage, which could increase bacterial contamination of the water
with fecal coliform and e. coli bacteria.
• Should be designed to retain for 24 hours the rainfall runoff from 2-year storm
event.
• Vegetation selection should be chosen not only for pollutant uptake and climate but
also for ease and frequency of maintenance.
• Extremes in weather and climate should be considered not the average.
• Design with the landscape not against it.
• Replanting of vegetation which initially fail may be necessary.
• A liner may be necessary to assist in retention of water due to losses from infiltra-
tion through the summer months depending on the seasonal level of groundwater.
Page 41 of 52
46. Wetland Design
The example above is one that is used for sewage treatment but has many of the aspects
desired in a constructed wetland for storm water runoff. Some type of sedimentation
chamber or pond should be located upstream so that the heavier settleable solids will set-
tle out prior to the wetland and thus reduce the load on the wetland. This settling pond
should be designed with a maximum velocity through the pond of around 1 to 1.5 feet per
second and a depth below the outfall of several feet to retain the sediment. This allows
for most of the sediment removal to occur in the settling pond and not in the wetland.
As the runoff leaves the settling pond, it enters a wetland inlet distribution system con-
sisting of a submerged perforated pipe covered by rip rap or a ditch with level lower bank
on the wetland side 90 degrees to the wetland length and roughly perpendicular to the
inlet flow pipe or ditch. This flow distribution system allows for full even parallel flow
across the full width of the wetland. A point inlet would provide for short circuiting of
the wetland and dead areas of flow that would not provide much in the way of treatment.
Wetland outlet distribution structures should be of similar design as the inlet distribution
structures. The level of water in the wetland can be controlled by adjustable weirs, ro-
tateable pipe elbows, expandable flexible piping, or other methods.
Page 42 of 52
47. The most efficient wetland is one that is completely vegetated with no open water. Open
water tends to provide concentration of the flow due to decreased flow resistance and re-
sults in short circuiting and decreased pollutant removal efficiencies for the wetland sur-
face area used. If large variations in expected flows need to be provided for, the wetland
that provides for high and low flows may be necessary. An example of such a wetland is
shown below.
In the example at the bottom of the previous page, short circuiting is addressed through
the use of a deep and a shallow meandering channel both of which are to be completely
vegetated but which allows for two different rainfall events.
In the first example, a wetland discharge system is also needed to collect the discharge
flow across the full width of the wetland evenly. Again this can be accomplished through
the use of a perforated pipe covered in rip rap located at a lower elevation in the wetland
than the inlet distribution device or with another ditch with a level bank perpendicular to
the wetland length. The ditch banks and internal surfaces on both types of ditches must
be lined or armored in some way to ensure that erosion does not take place in the ditch or
on the ditch banks. Both the inlet and the discharge ditches, if used, must be of sufficient
width and depth to ensure that the entering and discharging volume of storm water is
handled in such a way as to ensure an even distribution of water across the wetland.
Retention time for the water in a constructed wetland should be a minimum of thirty-six
hours. To be successful, the design of a constructed wetland should include input from a
Page 43 of 52
48. hydrologist, wetland specialist, wetlands plant specialist, and an engineer. Some method
of providing water during the dry season needs to be considered or the vegetation will be
dormant or dead at the time it is needed when the rains arrive.
Pocket wetlands have been used at commercial and industrial sites and by TriMet on their
westside light rail line. It is doubtful due to their size that these pocket wetlands remove
a large amount of pollutants but the do remove some. In some cases where insufficient
land is available to allow for a fully functioning wetland, removing some of the pollutants
from storm water runoff is preferable to not removing any.
The Natural Resources Conservation Service has a Wetland Conservation Standard for
Constructed Wetlands, Code 280, that should be reviewed during the design phase of a
constructed wetland.
Maintenance:
Phosphorus removal may be significant only during the first few years of vegetation es-
tablishment. This may be because in the first few years of vegetation growth the plants
have a high demand for nutrients and phosphorus until the vegetation is established and a
cycle of growth-death-growth recycling of the nutrients and phosphorus occurs. This
would lead to the conclusion that a constructed wetland, in order to continue to remove
certain pollutants, must have the dead vegetation removed and not allow it to recycle so
that the nutrients and pollutants will always be removed from the incoming storm water
and not from the dead vegetation. In this way the pollutant uptake will always be from
the storm water and not from the decaying vegetation of past uptake. Monitoring the
phosphorus and other pollutants entering and leaving the constructed wetlands will give a
better feel for when the removal of the dead vegetation should take place. Some of the
decaying vegetation needs to be available to provide for some of the nutrients and bio-
mass necessary for good vegetative growth. Excess decaying vegetation will reduce the
vegetative uptake of the pollutants from the incoming storm water.
Maintenance is of primary importance in order to maintain the pollutant uptake of a con-
structed wetland.. A maintenance plan needs to address removal of dead vegetation prior
to the winter wet season, debris removal from trash racks, sediment monitoring in the up-
stream settling ponds or forebays are likely to contain significant amounts of heavy met-
als and possibly organics. Maintenance of the constructed wetland actually starts in the
construction phase with the addition of organics such as compost to the soil. With proper
maintenance constructed wetlands can function for 20 years or longer. Any mowing of
the banks of the constructed wetland should also include a method for removal of those
trimmings periodically. Mowing or cutting back the vegetation also reduces evapotran-
spiration and reduces the amount of pollutant uptake until the vegetation reestablishes full
growth. Undesirable woody plant growth should be removed as soon as it is discovered.
The method for controlling the water level in the wetland will have to be adjusted peri-
odically as vegetation is established and as sediments accumulate in order to maintain the
optimum water depth for the vegetation. The sediment forebay or settling pond will need
to be checked and cleaned out in order to maintain good removal of the heavy sediments
Page 44 of 52