Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001 and up).pdf

Service Repair Manual
Models
329D and 329D L Excavator

Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02435581
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...

Illustration 1 g01216706
1. Disconnect harness assembly (4). Disconnect harness assemblies (2). Remove bolts (1).
Remove valve mechanism cover base (3) .
Installation Procedure
Note: Cleanliness is an important factor. Before the installation procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
2/3
2019/11/23

https://www.aservicemanualpdf.com/
My Dear Friend! Thank you very
much for visiting. Full manual if
required, please enter the
following URL into your browser.
https://www.aservicemanualpdf.com/

1. Position valve mechanism cover base (3). Install bolts (1). Tighten bolts (1) in a numerical
sequence.
2. Connect harness assembly (4). Connect harness assemblies (2) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 10:47:03 UTC+0800 2019
3/3
2019/11/23

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02435468
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
B. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
C. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
D. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod".
NOTICE
NOTICE
1/5
2019/11/23

Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine coolant from the cooling system. Refer to Operation and Maintenance
Manual, "Cooling System Coolant - Change".
2. Remove support (1) .
2/5
2019/11/23

3. Disconnect tube assemblies (2) and (4). Remove clamp (3). Loosen clamps (6). Remove
boot (5) .
4. Remove clamp (7). Remove bolt (8) .
5. Loosen clamp (10). Disconnect hose (9). Remove bolts (11) .
6. Remove the belt from the fan drive. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
3/5
2019/11/23

7. Remove bolts (15). Slide pulley (14) toward the fan. Remove bolts (13). Remove bracket
(12) .
8. Disconnect harness assembly (16). Loosen clamp (17) and disconnect hose (19). Disconnect
tube assembly (18) .
4/5
2019/11/23

9. Disconnect harness assemblies (20), (21), (22), and (24). Disconnect tube assembly (23) .
10. Disconnect tube assembly (26). Attach Tooling (A) and a suitable lifting device to cylinder
head (28). The weight of cylinder head (28) is approximately 175 kg (385 lb). Remove bolts
(25) and (27). Remove cylinder head (28) .
Sat Nov 23 10:47:58 UTC+0800 2019
5/5
2019/11/23

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02436485
Cylinder Head - Install
SMCS - 1100-012
Table 1
Required Tools
B 4C-5590 Anti-Seize Compound 1
C 6V-4876 Lubricant 1
NOTICE
1. Install a new cylinder head gasket.
1/6
2019/11/23

2. Attach Tooling (A) and a suitable lifting device to cylinder head (28). The weight of
cylinder head (28) is approximately 175 kg (385 lb). Position cylinder head (28) onto the
cylinder block.
3. Apply Tooling (B) to bolts (25). Apply Tooling (C) to new bolts (27). Install bolts (25) and
(27) according to the following procedure:
a. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 300 ± 15
N·m (221 ± 11 lb ft).
b. Loosen Bolt (1) through Bolt (14) until the washers are loose under the bolt heads.
c. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 130 ± 15
N·m (95 ± 11 lb ft).
d. Tighten Bolt (1) through Bolt (14) again in a numerical sequence to a torque of 130 ±
15 N·m (95 ± 11 lb ft).
2/6
2019/11/23

e. Turn Bolt (1) through Bolt (14) in a numerical sequence for an additional 90° (1/4
turn).
f. Tighten Bolt (15) through Bolt (20) in a numerical sequence to a torque of 55 ± 7
N·m (41 ± 5 lb ft).
4. Connect tube assembly (26) .
5. Connect tube assembly (23). Connect harness assemblies (20), (21), (22), and (24) .
6. Connect tube assembly (18). Connect hose (19) and tighten clamp (17) to 11 ± 1 N·m (97 ±
0.9 lb in). Connect harness assembly (16) .
3/6
2019/11/23

7. Position bracket (12). Install bolts (13). Position pulley (14) on the fan drive. Install bolts
(15) .
8. Install the fan drive belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
9. Connect hose (9). Tighten clamp (10) to 11 ± 1 N·m (97 ± 0.9 lb in). Install bolts (11) .
4/6
2019/11/23

10. Install clamp (7). Install bolt (8) .
11. Install boot (5). Tighten clamps (6) to 11 ± 1 N·m (97 ± 0.9 lb in). Connect tube assemblies
(2) and (4). Install clamp (3). Tighten clamp (3) to 7.5 ± 1 N·m (66 ± 0.9 lb in).
12. Install support (1) .
13. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
End By:
a. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod".
b. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
c. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
5/6
2019/11/23

d. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
Sat Nov 23 10:48:54 UTC+0800 2019
6/6
2019/11/23

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02450638
Water Temperature Regulator - Remove and Install - Engine
in Machine
SMCS - 1355-010
Removal Procedure
NOTICE
containing fluids.
NOTICE
1/5
2019/11/23

At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
fill cap is cool enough to touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with the skin
and eyes to prevent personal injury.
1. Drain the engine coolant into a suitable container for storage or for disposal. Drain the
coolant to a level that is below the water temperature regulator. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
2. Loosen clamp (2) and disconnect hose (1) from cover (3) .
2/5
2019/11/23

Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.

3. Remove bolts (4) .
4. Remove cover (3) .
5. Remove water temperature regulator (5) and gasket (6) .
3/5
2019/11/23

1. Install a new gasket (6). Install water temperature regulator (5) .
2. Position cover (3) .
3. Install bolt (4) .
4/5
2019/11/23

4. Connect hose (1) to cover (3) .
5. Tighten clamp (2) .
6. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change"and Operation and Maintenance Manual, "Capacities
(Refill)".
Sat Nov 23 10:49:50 UTC+0800 2019
5/5
2019/11/23

Shutdown SIS
Previous Screen
Product: EXCAVATOR
i02541413
Radiator - Remove
SMCS - 1353-011
Removal Procedure
Table 1
Required Tools
Start By:
A. Remove the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
NOTICE
containing fluids.
1/6
2019/11/23

Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001 and up).pdf

Recommended

Recommended

More Related Content

Similar to Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001 and up).pdf

Similar to Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001 and up).pdf (20)

More from sijipang18046

More from sijipang18046 (20)

Recently uploaded

Recently uploaded (20)

Caterpillar Cat 329D L Excavator (Prefix DTZ) Service Repair Manual (DTZ00001 and up).pdf