This document provides instructions for removing and installing the water temperature regulator on a Caterpillar C7 engine. It describes:
1. Draining the engine coolant below the level of the water temperature regulator.
2. Disconnecting the hose from the regulator cover and removing mounting bolts.
3. Installing the new regulator by reversing the removal steps, filling the cooling system, and tightening all connections to the specified torques.
Cleanliness is important to prevent contamination, and safety precautions are described for working with hot coolant and steam.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fjskexswksemmm
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) The removal procedure includes disconnecting harness assemblies, removing bolts, and removing the valve mechanism cover base.
3) The installation procedure specifies cleaning parts, positioning the base, installing bolts, and reconnecting harness assemblies.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fjjsekfxswzksmem
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Proper cleanliness and coolant drainage are emphasized.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fujsekfksemmaq
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and positioning the regulator cover with a new gasket before refilling the cooling system.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fusjefjskekem
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Cleanliness is emphasized to prevent contaminating parts.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fujsfkkskekmem
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) Key steps for removing the valve mechanism cover base include disconnecting harness assemblies, removing bolts, and removing the cover base.
3) Key steps for installing the cylinder head include attaching lifting tools, installing bolts in a specific tightening sequence, and connecting various tube assemblies and hoses.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fujsjefjwekskemm
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Cleanliness is emphasized to prevent contaminating parts.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...ufdjskeksmemzx
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) The removal procedure includes disconnecting harness assemblies, removing bolts, and removing the valve mechanism cover base.
3) The installation procedure specifies cleaning parts, positioning the cover base, installing bolts, and reconnecting harness assemblies.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C7 engine:
1) The removal procedure involves disconnecting various components like hoses, tubes, and harnesses before removing bolts and lifting the cylinder head off with lifting tools.
2) The installation procedure specifies applying anti-seize compound to bolts and lubricant to new bolts before lowering the cylinder head into place and torquing bolts to specified values.
3) Reconnecting components like hoses, tubes, harnesses and installing supports completes the installation.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fjskexswksemmm
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) The removal procedure includes disconnecting harness assemblies, removing bolts, and removing the valve mechanism cover base.
3) The installation procedure specifies cleaning parts, positioning the base, installing bolts, and reconnecting harness assemblies.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fjjsekfxswzksmem
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Proper cleanliness and coolant drainage are emphasized.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fujsekfksemmaq
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and positioning the regulator cover with a new gasket before refilling the cooling system.
Caterpillar cat 329 d l excavator (prefix dtz) service repair manual (dtz0000...fusjefjskekem
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Cleanliness is emphasized to prevent contaminating parts.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fujsfkkskekmem
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) Key steps for removing the valve mechanism cover base include disconnecting harness assemblies, removing bolts, and removing the cover base.
3) Key steps for installing the cylinder head include attaching lifting tools, installing bolts in a specific tightening sequence, and connecting various tube assemblies and hoses.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...fujsjefjwekskemm
The document provides instructions for removing and installing the water temperature regulator on a Caterpillar 329D excavator engine. The removal procedure involves draining the engine coolant, loosening a hose clamp, and disconnecting a hose from the regulator cover. The installation procedure specifies tightening tolerances for the hose clamp and connects the hose to the cover. Cleanliness is emphasized to prevent contaminating parts.
Caterpillar cat 329 d excavator (prefix dtz) service repair manual (dtz00001 ...ufdjskeksmemzx
1) The document provides instructions for removing and installing the valve mechanism cover base and cylinder head on a Caterpillar 329D excavator powered by a C7 engine.
2) The removal procedure includes disconnecting harness assemblies, removing bolts, and removing the valve mechanism cover base.
3) The installation procedure specifies cleaning parts, positioning the cover base, installing bolts, and reconnecting harness assemblies.
The document provides instructions for removing and installing a cylinder head on a Caterpillar C7 engine:
1) The removal procedure involves disconnecting various components like hoses, tubes, and harnesses before removing bolts and lifting the cylinder head off with lifting tools.
2) The installation procedure specifies applying anti-seize compound to bolts and lubricant to new bolts before lowering the cylinder head into place and torquing bolts to specified values.
3) Reconnecting components like hoses, tubes, harnesses and installing supports completes the installation.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
The document provides instructions to disassemble a final drive for excavator models 325D and 325D L. It involves 33 steps including removing bolts, gears, seals, carriers, shafts, washers and bearings. Cleanliness is important to prevent dirt entering during reassembly. Tools include a transmission repair stand, link brackets, retaining ring pliers, and a slide hammer puller. The procedure separates the final drive into individual components for repair or replacement.
The document provides step-by-step instructions for assembling a hydraulic pump. It lists 61 steps involving the installation of gaskets, seals, pins, plates, pistons, shafts, bearings, covers, and other components into the pump housing in the correct order and orientation. Special tools and safety precautions are noted. The process concludes by installing the completed pump control and connecting fittings.
This document provides instructions for removing and installing a flywheel housing on a 416C Backhoe Loader with a 3054 engine. It describes using lifting brackets and removing mounting bolts to detach the housing. Cleaning surfaces and replacing seals is emphasized. Proper tools and safety precautions are listed.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It outlines the required tools and steps to remove the housing, which include removing mounting bolts from the top and sides of the housing and lifting it off using lifting brackets. Reinstallation involves cleaning mating surfaces, placing the housing on the cylinder block, and reinstalling the mounting bolts with the specified torque. Instructions are also provided for removing and installing the crankshaft rear seal and flywheel.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. The removal procedure involves supporting the engine, removing mounting bolts from the top and bottom of the housing, attaching lifting tools to the housing, and using hammers to separate the housing from the cylinder block. The installation procedure specifies cleaning mating surfaces and inserting a new felt seal if needed before placing the housing on the cylinder block and securing it with mounting bolts. Tools including link brackets and lifting devices are listed.
This document provides instructions for removing and installing a crankshaft rear seal on a Caterpillar 3054 engine. It describes the necessary tools and parts, safety precautions, and step-by-step procedures for both removing the old seal and installing the new one. The procedures are separated into sections for engines with a 14-bolt housing assembly versus a 10-bolt housing assembly. Precise instructions are given for lubricating parts, inserting the seal, aligning components, and tightening bolts to the specified torque.
This document provides instructions for removing and installing a flywheel housing on a Caterpillar 3054 engine. It describes the required tools and gives step-by-step procedures for removing the housing which include supporting the engine, removing mounting bolts, attaching lifting tools, and removing bolts attaching the housing to the cylinder block. Reinstallation involves cleaning surfaces, positioning the housing, and tightening bolts to specifications.
Caterpillar Cat 345D L Excavator (Prefix YEE) Service Repair Manual (YEE00001...f7usuejkdkddm3
This document provides instructions for removing and installing various engine components on a Caterpillar 345D L excavator, including:
- Removing and installing the rear gear group. This involves removing several gears, seals, bolts and bearings. Precise positioning of bearings is required during installation.
- Removing the flywheel using lifting equipment and tooling. The flywheel weighs approximately 79 kg.
- Removing and installing the crankshaft rear seal using bolts, sealant and cleaning of parts. Proper inspection of the crankshaft surface is also noted.
Precise positioning and cleaning of parts is emphasized to ensure proper installation. Various specialty tools are listed to facilitate removal and installation
This document provides instructions for removing and installing a crankshaft pulley on a Caterpillar 3054 engine. It describes using a puller tool to remove the pulley and pressing the pulley onto the crankshaft during installation. Tightening specifications are included for attaching the pulley.
This document provides instructions for removing and installing a flywheel and crankshaft rear seal on a Caterpillar 3054 engine. It describes the required tools and multi-step processes for both removal and installation. For the flywheel, the instructions cover removing bolts, lifting the flywheel off, and potentially removing a ring gear. For the crankshaft rear seal, it differentiates between engines with 14-bolt and 10-bolt housings and explains cleaning, pressing or placing the seal, and torquing bolts.
This document provides instructions for removing the crankshaft front seal from a Caterpillar 3054 engine. The steps are:
1. Use a drill bit to drill out the lock tabs of the seal.
2. Pry the seal out of the housing with a seal removal tool.
3. Inspect the seal bore and remove any debris before installing the new seal.
Caterpillar Cat 345D L Excavator (Prefix RGG) Service Repair Manual (RGG00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It lists 31 steps for disassembly, removing components like the head, plates, seals, and pins. It then lists 31 steps for assembly, installing components like seals, spacers, washers, and plugs in reverse order of disassembly. Tools required are listed in tables. Cautions are provided about cleanliness, contamination, misassembly, and applying lubricant to parts.
Caterpillar Cat 345D L Excavator (Prefix PBT) Service Repair Manual (PBT00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling the swing drive of a 345D L excavator. It lists the required tools and gives step-by-step procedures to remove components such as the carrier assembly, ring gear, and bearings. Cleanliness is emphasized during assembly, with seals, O-rings and other parts replaced as needed. The instructions ensure the swing drive is properly disassembled and reassembled.
Caterpillar Cat 345C L Excavator (Prefix BWY) Service Repair Manual (BWY00001...f7usuejkdkddm3
The document provides instructions for disassembling and assembling the travel motor of a 345C excavator. It lists 31 steps to disassemble the various components of the travel motor, including removing the head, brake piston, disks, rotating group, and seals. Proper identification and cleaning of parts is emphasized to avoid contamination. The appropriate tools are also listed.
Caterpillar Cat 345D L Excavator (Prefix KFH) Service Repair Manual (KFH00001...f7usuejkdkddm3
This document provides instructions for removing and installing various components of a C13 engine, including:
1) Removing the rear gear group by removing covers, seals, gears, bolts, and bearings.
2) Removing the flywheel using lifting equipment and guide studs.
3) Installing the flywheel by applying threadlocker to bolts and checking runout.
4) Removing the crankshaft rear seal by removing bolts.
Caterpillar Cat 345C L Hydraulic Excavator (Prefix ESD) Service Repair Manual...f7usuejkdkddm3
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Caterpillar Cat 345C L Excavator (Prefix TBA) Service Repair Manual (TBA00001...f7usuejkdkddm3
This document provides instructions for disassembling and assembling a travel motor. The disassembly procedure involves 31 steps to remove parts like the head, plates, seals, pistons, and housing. The assembly procedure reverses the disassembly with 13 steps like installing seals, pistons, plates, and housing components. Precautions are provided to keep parts clean and in proper orientation to avoid damage. Tools required are listed for both procedures.
The document provides assembly instructions for a 345C excavator final drive system. It involves assembling three carrier assemblies that contain planetary gears, installing them into a ring gear housing along with other components like bearing cones and seals. The procedure has 26 steps and requires various tools. It ensures proper bearing preload is achieved and components are cleaned, lubricated and torqued correctly during reassembly.
The document provides instructions for disassembling and assembling a travel motor. It is a 31 step process that includes removing components like the head, brake piston, disks, and seals. Tools required are listed. Cleanliness is emphasized to prevent contamination of hydraulic components. Used parts should be replaced, and new seals and O-rings installed.
Fleet management these days is next to impossible without connected vehicle solutions. Why? Well, fleet trackers and accompanying connected vehicle management solutions tend to offer quite a few hard-to-ignore benefits to fleet managers and businesses alike. Let’s check them out!
What Could Be Behind Your Mercedes Sprinter's Power Loss on Uphill RoadsSprinter Gurus
Unlock the secrets behind your Mercedes Sprinter's uphill power loss with our comprehensive presentation. From fuel filter blockages to turbocharger troubles, we uncover the culprits and empower you to reclaim your vehicle's peak performance. Conquer every ascent with confidence and ensure a thrilling journey every time.
Implementing ELDs or Electronic Logging Devices is slowly but surely becoming the norm in fleet management. Why? Well, integrating ELDs and associated connected vehicle solutions like fleet tracking devices lets businesses and their in-house fleet managers reap several benefits. Check out the post below to learn more.
Ever been troubled by the blinking sign and didn’t know what to do?
Here’s a handy guide to dashboard symbols so that you’ll never be confused again!
Save them for later and save the trouble!
The Octavia range embodies the design trend of the Škoda brand: a fusion of
aesthetics, safety and practicality. Whether you see the car as a whole or step
closer and explore its unique features, the Octavia range radiates with the
harmony of functionality and emotion
Welcome to ASP Cranes, your trusted partner for crane solutions in Raipur, Chhattisgarh! With years of experience and a commitment to excellence, we offer a comprehensive range of crane services tailored to meet your lifting and material handling needs.
At ASP Cranes, we understand the importance of reliable and efficient crane operations in various industries, from construction and manufacturing to logistics and infrastructure development. That's why we strive to deliver top-notch solutions that enhance productivity, safety, and cost-effectiveness for our clients.
Our services include:
Crane Rental: Whether you need a crawler crane for heavy lifting or a hydraulic crane for versatile operations, we have a diverse fleet of well-maintained cranes available for rent. Our rental options are flexible and can be customized to suit your project requirements.
Crane Sales: Looking to invest in a crane for your business? We offer a wide selection of new and used cranes from leading manufacturers, ensuring you find the perfect equipment to match your needs and budget.
Crane Maintenance and Repair: To ensure optimal performance and safety, regular maintenance and timely repairs are essential for cranes. Our team of skilled technicians provides comprehensive maintenance and repair services to keep your equipment running smoothly and minimize downtime.
Crane Operator Training: Proper training is crucial for safe and efficient crane operation. We offer specialized training programs conducted by certified instructors to equip operators with the skills and knowledge they need to handle cranes effectively.
Custom Solutions: We understand that every project is unique, which is why we offer custom crane solutions tailored to your specific requirements. Whether you need modifications, attachments, or specialized equipment, we can design and implement solutions that meet your needs.
At ASP Cranes, customer satisfaction is our top priority. We are dedicated to delivering reliable, cost-effective, and innovative crane solutions that exceed expectations. Contact us today to learn more about our services and how we can support your project in Raipur, Chhattisgarh, and beyond. Let ASP Cranes be your trusted partner for all your crane needs!
2. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02435581
Valve Mechanism Cover Base - Remove and Install
SMCS - 1120-010
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Note: Cleanliness is an important factor. Before the removal procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/3
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g01216706
1. Disconnect harness assembly (4). Disconnect harness assemblies (2). Remove bolts (1).
Remove valve mechanism cover base (3) .
Installation Procedure
Note: Cleanliness is an important factor. Before the installation procedure, the exterior of the
component should be thoroughly cleaned. This will help to prevent dirt from entering the internal
mechanism.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
Illustration 2 g01216706
2/3
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 3 g01127431
1. Position valve mechanism cover base (3). Install bolts (1). Tighten bolts (1) in a numerical
sequence.
2. Connect harness assembly (4). Connect harness assemblies (2) .
End By: Install the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 10:47:03 UTC+0800 2019
3/3
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02435468
Cylinder Head - Remove
SMCS - 1100-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
Start By:
A. Remove the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
B. Remove the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
C. Remove the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
D. Remove the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
1/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1. Drain the engine coolant from the cooling system. Refer to Operation and Maintenance
Manual, "Cooling System Coolant - Change".
Illustration 1 g01216665
2. Remove support (1) .
Illustration 2 g01216682
2/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. 3. Disconnect tube assemblies (2) and (4). Remove clamp (3). Loosen clamps (6). Remove
boot (5) .
Illustration 3 g01216730
4. Remove clamp (7). Remove bolt (8) .
Illustration 4 g01216744
5. Loosen clamp (10). Disconnect hose (9). Remove bolts (11) .
6. Remove the belt from the fan drive. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
3/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. 9. Disconnect harness assemblies (20), (21), (22), and (24). Disconnect tube assembly (23) .
Illustration 8 g01216836
10. Disconnect tube assembly (26). Attach Tooling (A) and a suitable lifting device to cylinder
head (28). The weight of cylinder head (28) is approximately 175 kg (385 lb). Remove bolts
(25) and (27). Remove cylinder head (28) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 10:47:58 UTC+0800 2019
5/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02436485
Cylinder Head - Install
SMCS - 1100-012
Installation Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7575 Link Bracket 2
B 4C-5590 Anti-Seize Compound 1
C 6V-4876 Lubricant 1
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Install a new cylinder head gasket.
1/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. Illustration 1 g01216836
Illustration 2 g01217111
2. Attach Tooling (A) and a suitable lifting device to cylinder head (28). The weight of
cylinder head (28) is approximately 175 kg (385 lb). Position cylinder head (28) onto the
cylinder block.
3. Apply Tooling (B) to bolts (25). Apply Tooling (C) to new bolts (27). Install bolts (25) and
(27) according to the following procedure:
a. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 300 ± 15
N·m (221 ± 11 lb ft).
b. Loosen Bolt (1) through Bolt (14) until the washers are loose under the bolt heads.
c. Tighten Bolt (1) through Bolt (14) in a numerical sequence to a torque of 130 ± 15
N·m (95 ± 11 lb ft).
d. Tighten Bolt (1) through Bolt (14) again in a numerical sequence to a torque of 130 ±
15 N·m (95 ± 11 lb ft).
2/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. e. Turn Bolt (1) through Bolt (14) in a numerical sequence for an additional 90° (1/4
turn).
f. Tighten Bolt (15) through Bolt (20) in a numerical sequence to a torque of 55 ± 7
N·m (41 ± 5 lb ft).
4. Connect tube assembly (26) .
Illustration 3 g01216827
5. Connect tube assembly (23). Connect harness assemblies (20), (21), (22), and (24) .
Illustration 4 g01216825
6. Connect tube assembly (18). Connect hose (19) and tighten clamp (17) to 11 ± 1 N·m (97 ±
0.9 lb in). Connect harness assembly (16) .
3/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Illustration 5 g01216756
7. Position bracket (12). Install bolts (13). Position pulley (14) on the fan drive. Install bolts
(15) .
8. Install the fan drive belt. Refer to Operation and Maintenance Manual, "Belt -
Inspect/Adjust/Replace".
Illustration 6 g01216744
9. Connect hose (9). Tighten clamp (10) to 11 ± 1 N·m (97 ± 0.9 lb in). Install bolts (11) .
4/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 7 g01216730
10. Install clamp (7). Install bolt (8) .
Illustration 8 g01216682
11. Install boot (5). Tighten clamps (6) to 11 ± 1 N·m (97 ± 0.9 lb in). Connect tube assemblies
(2) and (4). Install clamp (3). Tighten clamp (3) to 7.5 ± 1 N·m (66 ± 0.9 lb in).
Illustration 9 g01216665
12. Install support (1) .
13. Fill the cooling system. Refer to Operation and Maintenance Manual, "Cooling System
Coolant - Change".
End By:
a. Install the rocker shaft and pushrods. Refer to Disassembly and Assembly, "Rocker Shaft
and Pushrod".
b. Install the unit injectors. Refer to Disassembly and Assembly, "Unit Injector - Remove".
c. Install the muffler. Refer to Disassembly and Assembly, "Muffler - Remove and Install".
5/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. d. Install the valve mechanism cover base. Refer to Disassembly and Assembly, "Valve
Mechanism Cover Base - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 10:48:54 UTC+0800 2019
6/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02450638
Water Temperature Regulator - Remove and Install - Engine
in Machine
SMCS - 1355-010
Removal Procedure
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. At operating temperature, the engine coolant is hot and under pressure.
Steam can cause personal injury.
Check the coolant level only after the engine has been stopped and the
fill cap is cool enough to touch with your bare hand.
Remove the fill cap slowly to relieve pressure.
Cooling system conditioner contains alkali. Avoid contact with the skin
and eyes to prevent personal injury.
1. Drain the engine coolant into a suitable container for storage or for disposal. Drain the
coolant to a level that is below the water temperature regulator. Refer to Operation and
Maintenance Manual, "Cooling System Coolant - Change" for the correct procedure.
Illustration 1 g00860997
2. Loosen clamp (2) and disconnect hose (1) from cover (3) .
2/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
19. Illustration 2 g00861004
3. Remove bolts (4) .
4. Remove cover (3) .
Illustration 3 g01140925
5. Remove water temperature regulator (5) and gasket (6) .
Installation Procedure
3/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
20. Illustration 4 g01140925
1. Install a new gasket (6). Install water temperature regulator (5) .
Illustration 5 g00861004
2. Position cover (3) .
3. Install bolt (4) .
Illustration 6 g00860997
4/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. 4. Connect hose (1) to cover (3) .
5. Tighten clamp (2) .
6. Fill the cooling system to the correct level. Refer to Operation and Maintenance Manual,
"Cooling System Coolant - Change"and Operation and Maintenance Manual, "Capacities
(Refill)".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Sat Nov 23 10:49:50 UTC+0800 2019
5/5
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Shutdown SIS
Previous Screen
Product: EXCAVATOR
Model: 329D EXCAVATOR DTZ
Configuration: 329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine
Disassembly and Assembly
324D, 325D, 326D and 329D Excavators and 329D MHPU Mobile Hydraulic Power
Unit C7 Engine Supplement
Media Number -RENR8645-13 Publication Date -01/05/2012 Date Updated -07/05/2012
i02541413
Radiator - Remove
SMCS - 1353-011
Removal Procedure
Table 1
Required Tools
Tool Part Number Part Description Qty
A 138-7573 Link Bracket 2
Start By:
A. Remove the hood. Refer to Disassembly and Assembly, "Hood - Remove and Install".
Note: Put identification marks on all hoses, on all hose assemblies, on all wires, and on all tube
assemblies for installation purposes. Plug all hose assemblies and all tube assemblies. This helps
to prevent fluid loss, and this helps to keep contaminants from entering the system.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Dealer Service
Tool Catalog" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/6
329D & 329D L Excavators DTZ00001-UP (MACHINE) POWERED BY C7 Engine(...
2019/11/23
https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...