Multilab India Suppliers of Elcometer 123 analog surface profile gauge measures the peak to Valley height of blast cleaned surface
http://www.multilab.biz/testing/elcometer-testing-equipments/surface-profile/elcometer123-surface-profile-gauge.htm
This easy to use gauge measures the peak-to-valley height of a blast cleaned surface.
The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as blasting proceeds.
Metric and Imperial versions
Part Number Description
E123A--M-
Elcometer 123 Surface Profile Gauge, Metric Version
E123A--E- Elcometer 123 Surface Profile Gauge, Imperial Version
Range 0 - 1000µm (0 - 40mils)
Scale 2µm (0.1 mil)
Dimensions 105 x 55 x 25mm (4.1 x 2.2 x 1”)
Weight 335g (8oz)
Certificate Available Certificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability.
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory.
Packing List Elcometer 123 Surface Profile Gauge, glass slide, 2mm allen key, carry case and operating instructions
Can be used in accordance with
ASTM D 4417-B, SANS 5772, US Navy NSI 009-32, US Navy PPI 63101-000
Beginners Guide to TikTok for Search - Rachel Pearson - We are Tilt __ Bright...
Elcometer 123 analog surface profile gauge measures the peak to Valley height of blast cleaned surface
1. data sheet
Elcometer 123 Surface Profile Gauge
This easy to use gauge measures the peakto-valley height of a blast cleaned surface.
The average of a series of measurements
provides an indication of the surface
roughness and allows the surfaces to be
compared as blasting proceeds.
Metric and Imperial versions
Elcometer 123 Surface Profile Gauge
Surface Profile
The degree of profile on the surface
affects a coating’s overall
performance. The height of the
profile (measured from the peaks to
the troughs) determines aspects
such as adhesion, coverage and
overall volume of coating used. If the
profile is too large the amount of
coating required to ensure adequate
coverage increases, otherwise there
is a danger that the peaks remain
uncoated - allowing rust spots to
occur. If the profile is too small, there
may be an insufficient key to produce
adequate adhesion, leading to
premature coating failure. Ensuring
the correct surface preparation
optimises the performance of the
coating and material usage.
There are four different methods
available for testing surface profile:
- Surface Comparators
- Replica Tape
- Surface Profile Gauges
- Surface Roughness Testers
TECHNICAL SPECIFICATION
Range
0 - 1000μm (0 - 40mils)
Scale
2μm (0.1 mil)
Dimensions
105 x 55 x 25mm (4.1 x 2.2 x 1”)
Weight
335g (8oz)
Part Number
E123A--M-
Elcometer 123 Surface Profile Gauge, Metric Version
E123A--E-
Elcometer 123 Surface Profile Gauge, Imperial Version
Packing list
www.elcometer.com
Elcometer 123 Surface Profile Gauge, glass slide, 2mm allen key, carry case and operating instructions
Elcometer 123 Surface Profile Gauge
V3: 12.10.11
1/2
2. data sheet
Related Products
Elcometer 7061 MarSurf PS1 Surface Roughness Tester
The Elcometer 7061 is a light weight and portable measuring solution for the range of
surface roughness measurements required for compliance to International Standards.
Elcometer 7061
Elcometer 223 Digital Surface Profile Gauge
A Digital Surface Profile Gauge which measures the peak-to-valley height of a surface
in a similar way to the Elcometer 224.
Elcometer 223
Elcometer 124 Thickness Gauge
The Elcometer 124 Thickness Gauge is used to measure peak-to-valley height of a
surface profile moulded in the Elcometer 122 Testex Replica Tape.
Elcometer 124
Elcometer 122 Testex Replica Tape
Elcometer 122 Testex Tape consists of foam with a non-compressible backing. The
foam side is rubbed into the surface providing a permanent mould of the peak-tovalley profile, which can be measured using the Elcometer 124 Thickness Gauge.
Elcometer 122
Elcometer 125 Surface Comparators
These extremely durable comparators allow the estimation of surface roughness of
either grit and shot blasted surfaces.
Elcometer 125
Elcometer 127 Keane-Tator Surface Comparators & Magnifier
The Elcometer 127 range of Surface Comparators are available in sand, shot or grit
surface profiles. Each comparator is supplied with 5 profile grades ranging from 0.5 5.5mils.
Elcometer 127
www.elcometer.com
Elcometer 123 Surface Profile Gauge
V3: 12.10.11
2/2