IJERA (International journal of Engineering Research and Applications) is International online, ... peer reviewed journal. For more detail or submit your article, please visit www.ijera.com
Performance Assessment of Polyphase Sequences Using Cyclic Algorithm
Kk2518251830
1. Sukanti Rout, Santosh Kumar Sahoo, Bidyadhar Basa / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 2, Issue 5, September- October 2012, pp.1825-1830
Monte Carlo Simulation Technique For Reliability Assessment Of
R.C.C. Columns
Sukanti Rout*, Santosh Kumar Sahoo**, Bidyadhar Basa***
*(Department Civil Engineering, SOA University, Bhubaneswar-30)
** (Department Civil Engineering, SOA University, Bhubaneswar-30)
*** ( Department Civil Engineering, SOA University, Bhubaneswar-30)
ABSTRACT
Efforts have been made since several adequately represented by the mathematical models
years to improve the engineering decision and or where solution of the model is not possible by
minimize the uncertainty, thus preventing the analytical method.
failure of the structure. Several probability MONTE CARLO SIMULATION yields a
theories have been developed in this regard to solution which is very close to the optimal, but not
ascertain the actual behavior of the structure or to necessarily the exact solution. However, it should be
determine the reliability of the structure as load noted that this technique yields a solution that
and resistances are random variables. This paper converges to the optimal or correct solution as the
presents the usefulness of “Monte Carlo number of simulated trials lead to infinity.
Simulation technique”, for checking the safety of For example , the integral of a single
R.C.C columns subjected to combined axial load variable over a given range corresponds to find the
and biaxial moments. area under the graph representing the function
A simple program for this method of .Suppose the function f(x) is positive and the lower
reliability analysis of R.C.C columns is developed and upper bounds are a and b ,respectively and the
which will benefit the designers and site engineers function is bounded above by the value „c‟. The
to define safety of the building in absolute terms. graph of the function is then contained within a
rectangle with sides of length c, and (b-a).
Keywords: Reliability; Monte Carlo method; If the points are picked up at random within
Simulation; R.C.C Column Design the rectangle and determine whether they lie beneath
the curve or not, it is apparent that, provided the
INTRODUCTION distribution of selected points is uniformly spread
Every engineering structure must satisfy the over the rectangle, the fraction of points falling on or
safety and serviceability requirement under the below the curve should be approximately the ratio of
service load over it; which means it must be reliable the area under the curve to the area of the rectangle.
against collapse and serviceability, such as excessive If N points are used and n of them fall under the
deflection and cracking. In the present study an curve, then, approximately,
𝑏
attempt has been made to study the reliability of a 𝑛 𝑓(𝑥) 𝑑𝑥
structural system and its component using Monte =
𝑁 𝑐(𝑏 − 𝑎)
Carlo Simulation Technique, which is a static, 𝑎
stochastic and continuous simulation model. In this
study the focus is distribution of a variable to
simulate the performance or behavior of a structural
system. The main reason for adopting Monte Carlo
Simulation Technique in the present work is to
estimate the parameters and probability distribution
of random variables whose values depend on the
interaction with specified probability distribution.
The relative advantage is that, this method avoids the
complicated closed form solution. The method can
also be used to study the statistical properties of
resistance.
MONTE CARLO METHOD
It is a simulation technique in which The accuracy improves as the number N
statistical distribution functions are created by using a increases. When it is decided that sufficient points
series of random numbers. This approach has the have been taken, the value of the integral is estimated
ability to develop many data in a matter of a few by multiplying the area of the rectangle c(b-a).
minutes on a digital computer. The method is For each point, a value of X is selected at random
generally used to solve problems which cannot be between a and b, say X0. A second random selection
1825 | P a g e
2. Sukanti Rout, Santosh Kumar Sahoo, Bidyadhar Basa / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 2, Issue 5, September- October 2012, pp.1825-1830
is made between o and c to give Y. if Y less than Step-3 But if Pu1< pu: Increase the value
equal to f(X0), the point is accepted in the count n, of Ku and repeat the process given below till
otherwise it is rejected and the next point is picked. Pu1=Pu => xu= KuD
This method is often powerful when used on integrals Calculation of Єi
of many variables by using a random number for Єi = (0.002/ai )/ (xu – 3D/7) where ai=xu-(D/2) +yi
each of the variable. Although random numbers have
been used, the problem being solved is essentially
determinate. Calculation of fci
If Єi < 0, then fci = 0
Column with axial load and biaxial moment If 0< Єi < 0.002 then fci = 446fck Єi (1-250 Єi )
Creation of random numbers: For Єi>0.002, fci= 0.446 fck
For normal distribution, Box and Mullar Calculation of fsi
technique is used to generate normal variates. If Єi<0.00174, fSi is calculated as = Єi.ES
Standard normal deviates are obtained by generating But if Єi>0.00174, fSi is obtained from table.
two uniform random number v1 and v2 (with a
uniform density range between 0 and 1 ) at a time.
Then the desired standard normal variates are given Calculation of Pu1
by pu1= C1 fck b D
u1=(2 ln 1/v1)1/2 cos 2πv2 => C1= 0.4461- C3/6)
u2=(2 ln 1/v1)1/2 sin 2πv2 C3= (8/7)(4/(7Ku-3))2
then two normal variates y1 and y2 are given by Pus1= (fs1-fc1) Ast1 +…
y1=µ+σ[(2 ln 1/v1)1/2 cos 2πv2] => Pu1 = Puc1 + Pus1
y2= µ+σ[(2 ln 1/v1)1/2 sin 2πv2] When Pu1 nearly equal Pu Calculate
where y1 and y2 are values of fck and fy respectively Muxx=Muyy= Puc1((D/2)-C2D) + (fs1-fc1) Ast1 y1+…
and µ= Mean and σ= standard deviation
(Already obtained from test results for fck and then
for fy)
Thus 400 normal variates of fck and 400 normal
variates of fy are generated using above normal
distribution equations.
Theoretical models or prediction equation for
moment of resistance (Rx and Ry)
Step-1
Start with Ku=1
xu = Kud = d
(a) Calculation of Єi
Єi = (0.0035/ai )/ xu
where ai = xu-(D/2) +yi
(b) Calculation of fci
If Єi < 0, then fci = 0
If 0< Єi < 0.002 then fci = 446fck Єi (1-250 Єi )
For Єi>0.002 , fci= 0.446 fck
(c) Calculation of fsi
If Єi<0.00174, fSi is calculated as = Єi.ES
But if Єi>0.00174, fSi is obtained from table.
(d) Calculation of Pu1
pu1= Puc1 +Pus1
=> Puc1 = 0.36fck.b.xu
=> Pus1= (fs1-fc1)Ast1 + (fs2-fc2) Ast2 + fs3 – fc3) Ast3
= n Asti (fsi − fci)
i=0
(e) Comparison of Pu1 with given Pu
If Pu1 = Pu
then Muxx = Muyy = Puc1[(D/2)-0.416d] +
n
i=1 Asti (fsi − fci)Yi
Step-2
But if Pu1 > Pu : Reduce the value of Ku and
repeat step-1 i.e, from (a) to (b) till Pu1 is nearly equal
to Pu. And then calculate Muxx (or) Muyy.
1826 | P a g e
5. Sukanti Rout, Santosh Kumar Sahoo, Bidyadhar Basa / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 2, Issue 5, September- October 2012, pp.1825-1830
FREQUENCY DISTRIBUTION CURVE
ANALYSIS OF RESULTS
In the present problem, MONTE CARLO
METHOD has been used to study the distribution
of a variable (R/Rn) which is a function of two
random variables fck and fy to simulate the
performance or behavior of a structural system and
to determine the reliability of 28 column
components. Here R is the moment of resistance of
a particular column for which Rn is the nominal
value of moment of resistance which has been
calculated using the nominal value of fck
(characteristic compressive strength of concrete of
M25 grade i.e. 25 N/mm2 and of fy (characteristic
yield strength of Fe 415 grade steel i.e. 415 N/mm2
) . Values of R have been normalized with its
corresponding nominal value of Rn so that the
statistics of R of different designs could be
compared. Hence instead of studying the
distribution of R the distribution of R/Rn is studied.
It is to be noted that Rn is deterministic and is
constant for a particular design. The frequency
distribution of the generated samples of R/Rn are
presented in the form of tables, histograms and
frequency polygon curves from which it has been
found that the normal distribution fits the generated
data well. This is very much consistent with the
results obtained by Ellingwood. et al (1997) who
have also fitted a normal distribution to the lower
tail below 5% fractile of the generated strength
distribution result as given in the table
“SUMMARY OF RESULTS”. It is observed that
the resulting values of mean, standard deviation
and γR (Ratio of design value of R to Rn) are
comparable with standard values of mean , standard
deviation and R as presented in the table
“RESISTANCE STASTICS OF R/Rn” . Also from
the comparison drawn between experimental
results and theoretical exact values of mean and
standard deviation of R it is found that there is a
maximum deviation of 3.6% in the values for mean
in Rx for column category A1-C5. As the error for
mean is below 4%, these category of column can be
considered reliable from safety point of view.
1829 | P a g e
6. Sukanti Rout, Santosh Kumar Sahoo, Bidyadhar Basa / International Journal of Engineering
Research and Applications (IJERA) ISSN: 2248-9622 www.ijera.com
Vol. 2, Issue 5, September- October 2012, pp.1825-1830
CONCLUSION [3] Rashedi M.R. and Moses I.
Evaluation of reliability allows one to (1988),”Identification of failure Modes in
formulate a rational design and optimization System Reliability”, J. Struct. Div. ASCE,
procedure. In terms of the design problem rather 114(2), 292-313.
than analysis, a major advantage of reliability based [4] Val, D.V. and Melchers,
design is the elimination of deterministic design R.E.(1997)”Reliability Determination of
restrictions in the individual members of the Deteriorating R.C.Slab Bridge”:”Method:
structural design. The total structure is only as First order reliability method.(FORM)”,
strong as its “weakest element” which is here the ASCE. J. Struct. Engg. , 123(12).
column designated as A1-C5. The members with Books
very high levels of reliability do not contribute to [1] Ranganathan. R. (1990), “Reliability
overall structure reliability. As the weakest link i.e. Analysis and Design of Structures” Tata
the column designated as A1-C5 is reliable from McGraw Hill.
safety point of view. Hence the total structure is [2] Verghese. P.c.(1994) “ Limit State Design
reliable from strength of the column point of view Of Reinforced CONCRETE “ Prentice
The error between experimental results Hall of India ,New Delhi.q
and theoretical exact values for all 28 columns Codes
show that the design is adequate. i.e. the columns [1] Bureau of Indian Standard (1978) “Design
have sufficient strength to resist the applied loads Aids to IS: 456-1978 for Reinforced
and experimental results well agree with theoretical Cement Concrete”, (sp:16-1980) .
exact value. Also, the experimental resistance [2] Bureau of Indian Standard (2000) “Indian
statistic satisfies the standard statistics resistance Standard Code of Practice for Plain and
values. Reinforced Cement Concrete”, IS:456-
Hence, it is calculated that the columns of typical 2000.
floor of the building under consideration are [3] Bureau of Indian Standard (1980)
structurally reliable. “Explanatory Hand Book to IS 456-
1978”,SP-34.
REFERENCES [4] Bureau of Indian Standard (1980) “Hand
Journal papers Book on Concrete Reinforcement and
[1] Chikkodi. p. and Ranganathan. R. (1988), Detailing”,sp-34.
“Partial Safety factors for R.C.C. Design”, [5] Ranganathan. R.(1987), “Reliability
Intl. J.of structures. vol.8,127-149 . Analysis and Design of R.C.C. Slabs
[2] Ellingwood. B.R.(1979), “Reliability ,Beams, Columns and Frames “- code
Based Evaluation of Design Criteria” J. calibration report no. D.S. and T:4/1/83-
Str. Div.ASCE.105.ST-4,713-737. stp.111/5, Civil Engg.Deptt.,IIT.Mumbai.
1830 | P a g e