2. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01368091
Idler Gear - Remove and Install
SMCS - 1206
Removal Procedure
Start By:
A. Remove the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
B. Remove the front cover. Refer to Disassembly and Assembly, "Housing (Front) - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/5236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
3. Illustration 1 g00721939
Note: Rotate the crankshaft until the timing marks on the following gears are aligned:
crankshaft gear, camshaft gear, fuel injection pump gear and idler gear (1) .
1. Remove outer washer (3) from the idler gear shaft.
2. Use a suitable puller to remove idler gear (2) .
Note: Do not rotate the crankshaft once the idler gear has been removed. If the crankshaft is
rotated, the number 1 piston must be set to the top center position. Refer to Testing and
Adjusting, "Finding Top Center Position for No. 1 Piston".
3. Remove the inner washer from the idler gear shaft (not shown). The inner washer is located
behind the idler gear.
Remove the Idler Gear Shaft
Table 1
Required Tools
Tool Part Number Part Description Qty
A 1P-0074 Slide Hammer Puller Gp 1
B 4C-5651 Threaded Adapter 1
2/5236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
4. Illustration 2 g00721895
(4) Idler gear shaft
(5) Oil hole
(6) O-ring seal
Illustration 3 g00721904
1. Remove O-ring seal (6) .
2. Thread tool (B) onto tool (A) .
3. Use tool (A) to remove idler gear shaft (4) .
Install the Idler Gear Shaft
Table 2
Required Tools
Tool Part Number Part Description Qty
C Installation Tool 1
3/5236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
5. D 159-9076 Seal Installer Handle 1
Illustration 4 g00721922
1. Ensure that oil hole (5) is in the up position.
2. Use a soft hammer (8) to start the idler gear shaft into the cylinder block.
Illustration 5 g00721925
3. Use tool (C) and tool (D) to install the idler gear shaft.
4. Drive the idler gear shaft with the installation tool until the installation tool makes contact
with the machined surface of the cylinder block.
Installation Procedure
1. Install O-ring seal (6) .
2. Install the inner washer onto the idler gear shaft.
3. Install idler gear (2) .
4/5236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
6. Note: Ensure that the timing marks on the crankshaft gear, the camshaft gear, and the fuel
injection pump gear are aligned with the timing marks on the idler gear (1) .
4. Install the outer washer (3) onto the idler gear shaft.
End By:
a. Install the front cover. Refer to Disassembly and Assembly, "Housing (Front) - Install".
b. Install the fan. Refer to Disassembly and Assembly, "Fan - Remove and Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:48:23 UTC+0800 2019
5/5236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
7. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01354640
Housing (Front) - Remove
SMCS - 1151-011
Removal Procedure
Start By:
A. Remove the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
B. Remove the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
C. Remove the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump
- Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
8. Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
Illustration 1 g00594914
1. Disconnect return spring (1) from the throttle lever on the front housing.
Note: It is necessary to get a reference for the maximum fuel setting in order to remove the
front housing. This setting must be taken from the original front housing before the front
housing is removed.
2. Establish a reference for the maximum fuel setting. Refer to the Testing and Adjusting
Module, "Fuel Setting - Adjust" topic for more information.
Illustration 2 g00595216
3. Remove four nuts (3), bolt (2), and plate (4) from the back side of the front housing.
2/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
9. Illustration 3 g00598941
4. Remove bolts (5) from the back side of the front housing.
Illustration 4 g00598948
Note: Mark the location of the bolts for the front housing. The bolts for the front housing
are different lengths and the bolts must be installed in the original location.
5. Remove bolts (6) and two nuts (7) that fasten the front housing to the cylinder block.
6. Remove front housing (8) and the gasket from the cylinder block. Inspect the gasket and the
front housing for damage. If the gasket or the front housing is damaged, use new parts for
replacement.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:49:18 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
10. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01354651
Housing (Front) - Install
SMCS - 1151-012
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Make sure that the mating surfaces of the front housing and the cylinder block are clean and
free from damage.
Illustration 1 g00598948
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
11. 2. Put the gasket and front housing (8) in position on the engine.
Note: The bolts for the front housing are different lengths and the bolts must be installed in
the original location.
3. Install two nuts (7) and bolts (6) that fasten the front housing to the engine.
Illustration 2 g00598941
4. Install bolts (5) in the back side of the front housing.
Illustration 3 g00595216
5. Put plate (4) in position on the engine and install bolt (2) and four nuts (3) .
6. Set the maximum fuel adjustment. Refer to the Testing and Adjusting Module, "Fuel Setting
- Adjust" topic for more information.
2/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
12. Illustration 4 g00594914
7. Connect return spring (1) to the throttle lever on the front housing.
End By:
a. Install the fuel injection pump. Refer to Disassembly and Assembly, "Fuel Injection Pump -
Install".
b. Install the crankshaft pulley. Refer to Disassembly and Assembly, "Crankshaft Pulley -
Remove and Install".
c. Install the alternator. Refer to Disassembly and Assembly, "Alternator - Remove and
Install".
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:50:14 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
13. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01150784
Crankcase Breather - Remove and Install
SMCS - 1317-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
14. Illustration 1 g00610373
1. Loosen bolts (3) and remove breather cover (6) from the valve mechanism cover.
2. Remove the diaphragm and plate (4). Remove spring (5) .
3. Clean vent hole (2) and breather tube (1). Clean cavity (7) for the breather assembly in the
valve mechanism cover.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Make sure that the components of the breather assembly are installed
correctly. Engine damage may occur if the breather assembly is not
working properly.
2/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
15. Illustration 2 g00610373
1. Install a new spring (5) in cavity (7) for the breather assembly.
2. Install a new diaphragm and plate (4) on top of spring (5) .
3. Install breather cover (6) and four bolts (3). Tighten the bolts to a torque of 9 N·m (80 lb
in).
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:51:10 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
16. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01317371
Valve Mechanism Cover - Remove and Install
SMCS - 1107-010
Removal Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
17. Illustration 1 g00583098
1. Loosen hose clamps (1) and remove breather tube (2) from the engine.
Illustration 2 g00583101
2. Remove three cap nuts (3), the washers and the rubber seals.
3. Remove valve mechanism cover (4) and the gasket from the engine.
Installation Procedure
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
1. Check the condition of the gasket and the rubber seals. If the gasket or the rubber seals are
worn or damaged, use new parts for replacement.
2/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
18. Illustration 3 g00583101
2. Put the gasket and valve mechanism cover (4) in position on the engine.
3. Lubricate cap nuts (3) with clean engine oil. Install the rubber seals, the washers and cap
nuts (3) .
Note: Do not overtighten the cap nuts on the valve mechanism cover.
4. Tighten cap nuts (3) to a torque of 11 N·m (8 lb ft).
Illustration 4 g00583098
5. Put breather tube (2) in position on the engine and tighten hose clamps (1) .
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:52:05 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
19. Thank you very much for
your reading. Please Click
Here. Then Get COMPLETE
MANUAL. NO WAITING
NOTE:
If there is no response to
click on the link above,
please download the PDF
document first and then
click on it.
20. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01318486
Rocker Shaft and Pushrod - Remove
SMCS - 1102-011; 1208-011
Removal Procedure
Start By:
A. Remove the valve mechanism cover. Refer to Disassembly and Assembly, "Valve
Mechanism Cover - Remove and Install".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
21. Illustration 1 g00698000
1. Loosen eight bolts (1) that fasten the brackets for the rocker shaft (4) to the cylinder head.
Begin with the inner bolts and work toward the outer bolts.
2. Loosen four nuts (3). Begin with the inner nuts and work toward the outer nuts.
Note: Rocker shaft brackets (4) contain three plates (2) that include the studs for the valve
mechanism cover. The plates must be installed in the original location in order to install the
valve mechanism cover.
3. Remove bolts (1) and nuts (3) from the brackets for the rocker shaft (4) .
2/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
22. Illustration 2 g00590103
4. Remove rocker shaft assembly (4) from the cylinder head.
Note: Roll pins (5) are installed in the brackets of rocker shaft (4) in order to align rocker
shaft assembly (4) with oil holes (7) in the cylinder head. Oil holes (7) provide lubrication
to rocker shaft assembly (4) .
5. Place an identification mark on each pushrod (6) in order to locate the pushrods for
installation. Remove eight pushrods (6) from the engine.
Copyright 1993 - 2019 Caterpillar Inc.
All Rights Reserved.
Private Network For SIS Licensees.
Fri Nov 15 12:53:01 UTC+0800 2019
3/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...
23. Shutdown SIS
Previous Screen
Product: SKID STEER LOADER
Model: 246 SKID STEER LOADER 5SZ
Configuration: 236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034 Engine
Disassembly and Assembly
3034 Engine for Caterpillar Built Machines
Media Number -SENR5013-08 Publication Date -01/11/2008 Date Updated -14/11/2008
i01511617
Rocker Shaft - Disassemble
SMCS - 1102-015
Disassembly Procedure
Start By:
A. Remove the rocker shaft assembly. Refer to Disassembly and Assembly, "Rocker Shaft and
Pushrod - Remove".
NOTICE
Keep all parts clean from contaminants.
Contaminants may cause rapid wear and shortened component life.
NOTICE
Care must be taken to ensure that fluids are contained during
performance of inspection, maintenance, testing, adjusting and repair
of the product. Be prepared to collect the fluid with suitable containers
before opening any compartment or disassembling any component
containing fluids.
Refer to Special Publication, NENG2500, "Caterpillar Tools and Shop
Products Guide" for tools and supplies suitable to collect and contain
fluids on Caterpillar products.
Dispose of all fluids according to local regulations and mandates.
1/3236, 246, 248 Skid Steer Loader 5SZ00001-03999 (MACHINE) POWERED BY 3034...
2019/11/15https://127.0.0.1/sisweb/sisweb/techdoc/techdoc_print_page.jsp?returnurl=/sis...