Instruction of brother lc 123, lc-125, lc-127 refillable cartridge

1. Refill Instructions for Brother LC
Removing the cover before refill
On the back side of the cartridge
collars of the ink chamber inside click in place
Removing the front cover above the ink outlet and air valve by using a small screwdriver. Carefully
push in the 2 retaining collars and th
Afterwards, carefully remove the cover from the ink cha
On the back cover the retaining collars are more difficult to reach. Please proceed particularly
careful. Push the retaining collars in and th
pull the ink chamber out of the cove
2 options to refill Brother cartridge
Option 1 it is sufficient to remove only the front cover above the ink outlet and air valve. Drill the
hole into the upper left corner next to the air valve. Fill
through this hole. Reseal the opening with a sealing plug or hot glue. Press the front cover onto the
ink chamber until the retaining coll
ink chamber by the cover and therefore seals the opening securely
Option 2 remove both covers from the ink chamber. Fill
into the ink chamber. Be careful not to damage the side foils with needle or syringe while refilling.
Reseal the filler opening with a sealing plug or hot glue. Put the back cover onto the ink chamber
and press until the retaining coll
chamber and cover for a plug that fits plain onto the chamber. The sloping
presses the plug firmly into place and seals the opening securely. At last attach the front cover onto
the ink chamber and push until the retaining collars click into place
Brand names and trademarks are
Copyright
Refill Instructions for Brother LC-123, LC-125, LC
refilling ink.
two holes on each part of the cover. That is where the retaining
collars of the ink chamber inside click in place.
the front cover above the ink outlet and air valve by using a small screwdriver. Carefully
push in the 2 retaining collars and then push them rightwards as the first two pictures sho
carefully remove the cover from the ink chamber.
On the back cover the retaining collars are more difficult to reach. Please proceed particularly
careful. Push the retaining collars in and then leftwards as the first two pictures show.
pull the ink chamber out of the cover.
2 options to refill Brother cartridges
ption 1 it is sufficient to remove only the front cover above the ink outlet and air valve. Drill the
hole into the upper left corner next to the air valve. Filling in the recommended amount of ink
through this hole. Reseal the opening with a sealing plug or hot glue. Press the front cover onto the
ink chamber until the retaining collars click into place. The sealing plug is pressed firmly onto the
refore seals the opening securely.
remove both covers from the ink chamber. Filling in the recommended amount of ink
into the ink chamber. Be careful not to damage the side foils with needle or syringe while refilling.
ler opening with a sealing plug or hot glue. Put the back cover onto the ink chamber
and press until the retaining collars click into place. It is enough place available between ink
chamber and cover for a plug that fits plain onto the chamber. The sloping
presses the plug firmly into place and seals the opening securely. At last attach the front cover onto
the ink chamber and push until the retaining collars click into place.
are the property of their respective holders and are for descriptive
Copyright 1993 - 2016 euccoi . All Rights Reserved.
www.euccoi.com
125, LC-127 Cartridge
two holes on each part of the cover. That is where the retaining
the front cover above the ink outlet and air valve by using a small screwdriver. Carefully
n push them rightwards as the first two pictures show.
On the back cover the retaining collars are more difficult to reach. Please proceed particularly
n leftwards as the first two pictures show. Then easily
ption 1 it is sufficient to remove only the front cover above the ink outlet and air valve. Drill the
in the recommended amount of ink
through this hole. Reseal the opening with a sealing plug or hot glue. Press the front cover onto the
click into place. The sealing plug is pressed firmly onto the
in the recommended amount of ink
into the ink chamber. Be careful not to damage the side foils with needle or syringe while refilling.
ler opening with a sealing plug or hot glue. Put the back cover onto the ink chamber
rs click into place. It is enough place available between ink
chamber and cover for a plug that fits plain onto the chamber. The sloping back of the cover
presses the plug firmly into place and seals the opening securely. At last attach the front cover onto
descriptive purpose only.