Mesin dapat membantu manusia melakukan pekerjaan dengan mudah, cepat dan efisien. Terdapat dua jenis mesin, yaitu mesin ringkas dan mesin kompleks. Mesin ringkas menggunakan prinsip mesin sederhana seperti tuas, roda dan gandar, skru, satah condong, baji, takal dan gear untuk mempermudah pekerjaan manusia.
1. SIMPLE MACHINE AND COMPLEX
MACHINE
MESIN RNGKAS DAN MESIN KOMPLEKS
1. MACHINE IS A TOOL THAT HELPS US TO DO
OUR WORK EASILY, FASTER AND
EFFICIENTLY.NG /MESIN ADALAH ALATAN
YANG MEMBANTU KITA BEKERJA SECARA
MUDAH, CEPAT DAN CEKAP
2. MACHINE CAN SAVE OUR TIME AND
ENERGY./MESIN BOLEH MENJIMATKAN MASA
DAN TENAGA
3. THERE ARE TWO TYPES OF MACHINES :
SIMPLE MACHINE AND COMPLEX MACHINE. /
TERDAPAT DUAJENIS MESIN : MESIN RINGKAS
DAN MESIN KOMPLEKS
2. SIMPLE MACHINE/MESIN RINGKAS
1. SIMPLE MACHINE IS A DEVICE THAT ALLOWS US TO
USE LESS FORCE TO MAKE WORK EASIER AND
FASTER./MESIN RINGKAS ADALAH ALAT YANG
MEMBOLEHKAN KITA MENGGUN.AKAN KURANG
DAYA MENJADIKAN KERJA LEBIH SENANG DAN
LEBIH CEPAT
2. EXAMPLES OF SIMPLE MACHINES ARE
CONTOH/ MESIN RINGKAS IALAH :
i) WHEEL AND AXLE/RODA & GANDAR
ii) SCREW/SKRU ii)LEVER/TUAS
iii)INCLINED PLANE/SATAH CONDONG
iii)WEDGE/BAJI vii)GEAR/GEAR
iv) PULLEY/TAKAL
3. WHEEL AND AXLE/RODA DAN GANDAR
1. A wheel and axle is a machine that made up of large wheel
connected to a rod called axle.Roda dan gandar adalah
mesin yang terdiri daripada roda yang besar yang
bersambung kepada roda yang dipanggil gandar.
2. When wheel turns, axle also turns./Bila roda
berputar, gandar juga berputar.
3. Wheel and axle helps us to move or carry heavy objects
easily. Roda dan gandar menolong kita menggerakkan
atau mengangkat objek dengan mudah.
4. Normally, wheel is bigger than axle. This can reduce the
energy to do work.Biasanya, roda adalah lebih besar dari
gandar. Ini akan mengurangkan tenaga untuk melakukan
kerja.
4. WHEEL AND AXLE/RODA DAN GANDAR
5. The direction of force is always opposite the directions of
motion load.
Arah daya selalunya bertentangan dengan daya gerakan
beban.
1. Example/Contoh :
To take water from well, a bucket is tied to an axle.
Mengambil air dari perigi, bakul diikat pada roda.
The axle can be rotated by using the wheel.
Gandar boleh dipusing menggunakan roda.
When the wheel and axle rotates, the bucket can move up
or down to carry water.
Bila roda dan gandar berputar, bakul akan bergerak naik ke
atas atau ke bawah untuk membawa air.
5. WHEEL AND AXLE/roda dan gandar
7. Other examples of wheel and axles are :
Contoh lain roda dan gandar adalah :
Car spanner Screw driver Door knob Hand-drawn well
Steering
wheel
Car tyre
Pencil
sharpener Tap water
6. Lever/TUAS
1. Lever consists of a bar that rest on a support.
Tuas mengandungi bar yang diletakkan pada satu
sokongan.
2. A lever has three main parts known as effort, fulcrum and
load./Tuas terdiri daripada tiga bahagian utama
iaitu, daya, fulkrum dan beban.
3. The effort is the force applied on the lever./Daya adalah
tenga yang dikenakan pada tuas.
4. The fulcrum is the fixed point where the lever turns./
Fulkrum ialah titik tetap di mana tuas berputar.
5. The load is the object that the lever lifts or moves.
Beban adalah objek di mana tuas angkat atau gerakkan.
7.
8. Lever/Tuas
6. The nearer the fulcrum from the load (an object), the less
effort we need. So when we used lever, we must :
Semakin dekat fulkrum dengan beban (objek), semakin
sedikit tenaga yang diperlukan. Jadi bila kita menggunakan
tuas, kita mestilah :
place the fulcrum as near the load as possible
letakkan fulkrum sedekat mungkin dengan beban
Apply the effort as far as possible
Kenakan daya sejauh mungkin.
7. Lever can be classified into three categories, according to
the position of fulcrum, load and effort.
Tuas boeh dikelaskan kepada tiga kategori, berdasarkan
kepada kedudukan fulkrum, beban dan daya
9. Lever/TUAS
FIRST CLASS LEVER
TUAS KELAS PERTAMA
SECOND CLASS
LEVER/TUAS KELAS
KEDUA
THIRD CLASS LEVER
TUAS KELAS KETIGA
POSITION OF
FULCRUM, LOAD
AND EFFORT
KEDUDUKAN
FULKRUM, BEBAN
DAN DAYA
FULCRUM IN THE
MIDDLE ./FULKRUM
BERADA DI TENGAH
LOAD IN THE
MIDDLE./ BEBAN
BERADA DI TENGAH
EFFORT IN THE
MIDDLE./ BERADA
DI TENGAH
EXAMPLES
CONTOH
SCISSORS, HAMMER,
PLIERS, SEE SAW
GUNTING, TUKUL,
PLAYAR, JONGKANG-
JONGKIT
BOTTLE OPENER,
WHEELBARROW,
NUTCRACKER, PAPER
CUTTER./PEMBUKA
BOTOL, KERETA
SORONG, PEMECAH
BUAH, PEMOTONG
KERTAS
FISHING ROD,
BROOM, ICE TONGS,
TWEEZER, ARM
PENYAPU, PENYEPIT
AIS, PENYEPIT,
LENGAN
11. Wedge/BAJI
1. A wedge consists of one or two inclined plane joined
together to form a V-shaped or a sharp edge.
Baji terdiri daripada satu atau dua satah condong
digabungkan bersama untuk membentuk bentuk V
atau hujung tajam
2. It is use to cut or separate an object.
Ianya digunakan untuk memotong atau memisahkan
objek.
3. Example of wedge are : knife, pin, needle, axe,
thumbtack, door stopper and spear.
Contoh baji ialah : pisau, pin, jarum. Kapak, peku
tekan,, penahan pintu, lembing
13. pulley
1. A pulley is a wheel that turns around an axle. A
rope goes over a pulley. The rope is used to
connect the load with the effort.
Takal adalah roda yang berputar pada gandar.
Tali melilit pada takal. Tali digunakan untuk
menyambung beban dengan daya.
2. There are three types of pulley :
Terdapat tiga jenis takal :
• Fixed pulley/Takal tetap
• Movable pulley/Takal bergerak
• Combined pulley system.
Sistem takal bergabung
14. pulley
2. We can use 2 or 3 pulley at the same to lift an
object. It can reduces force needed to lift up the
load.
Kita boleh menggunakan 2 atau 3 takal pada
waktu yang sama untuk mengangkat objek.
Ianya boleh mengurangkan daya yang
diperlukan untuk mengangkat beban.
15. FIXEDpulley/takal tetap
1. A fixed pulley is a pulley that does not move up.
Takal tetap ialah takal yang tidak bergerak.
2. A pulley can change the direction of the
force, making it easier to lift things up. When the
rope is pulled, the load is pulled up.
Takal boleh mengubah arah daya, menjadikan
lebih senang untuk mengangkat objek
3. The distance moved by the load is equal to the
distance move by the effort.
Jarak pergerakan beban adalah sama dengan
jarak daya.
16. FIXEDpulley/takal tetap
4. Examples : raising a flag, well, lifting a heavy object
Contoh : menaikkan bendera, perigi, mengangkat objek
berat
17. Movablepulley/takal bergerak
1. The movable pulley moves together with the load.
Takal bergerak akan bergerak bersama-sama dengan
beban.
1. The force needed to pull an object is half the weight of an
object./Daya yang diperlukan untuk menarik objek adalah
separuh daripada berat objek.
2. A movable pulley does not change the direction of the
force. Both the effort and the load move in the same
direction./Takal bergerak tida mengubah arah daya.
Kedua-duanya bergerak dalam satu arah.
18. Combination pulley system/sistem
takal bergabung
1. The combination pulley system is a combination of fixed
and movable pulleys.
Takal bergabung adalah gabungan takal tetap dan takal
bergerak.
2. The force needed to pull an object is half the weight of an
object./Daya yang diperlukan untuk mengangkat objek
adalah separuh daripada berat objek.
19. Screw/skru
1. A screw is a helical inclined plane.
Skru adalah satah condong berbentuk heliks.
2. The longer the inclined plane is, the closer will be
thread of the screw, and less force needed to move
the load./Semakin panjang satah condong, semakin
dekat benang pada skru dan semakin sedikit daya
diperlukan untuk menggerakkan beban
3. It is used to fixed objects together and also to raise
an object.
Ianya digunakan untuk melekatkan objek bersama-
sama dan juga untuk menaikkan objek
20. screw
4. Examples :
Screw Bottle
Opener G- clamp Car jack
Bolt and nut Drill Spiral staircase Car lid
21. INCLINED PLANE/satah condong
1. Actually it is a flat surface placed in
slanting manner. One side will be
higher than other
Sebenarnya merupakan permukaan
rata yang diletakkan dan keadaan
condong. Satu bahagian adalah
lebih side tinggi dari bahagian lain.
22. INCLINED PLANE/satah condong
2. Inclined planes make it easier to move heavy
objects. It can reduce the effort needed o move
an object.
Satah condong menjadikan lebih mudah untuk
mengangkat objek berat. Ianya boleh
mengurangkan daya untuk mengangkat beban.
3. It is easier to push a heavy load up a gentle
inclined plane than a steep inclined plane
Adalah lebih mudah untuk menolak objek berat
pada permukaan yang agak landai berbanding
satah condong yang curam.
24. gear
1. It consists a wheel with teeth. The teeth fix
together when the gears are placed together.
Mengandungi roda bersama dengan gigi. Gigi
dilekatkan bersama bila gear diletakkan
bersama.
2. Gears make movement easier.
Gear menjadikan pergerakan lebih mudah.
25. gear
3. Gears also help change the speed and the
direction of movement.
Gear juga menolong mengubah kelajuan dan
arah pergerakan.
4. Gears also can be used to control several
things simultaneously.
Gear juga menolong untuk mengawal beberapa
benda secara serentak.
26. gear
3. When one gears turns anticlockwise, the other gears
turns in the opposite direction (clockwise)
Bila satu gear bergerak arah lawan jam, satu lagi
bergerak pada arah bertentangan (arah lawan jam)
27. gear
3. When the big gear turns once, the small
gear turns many times. Therefore the
small gear turns faster than the big gear.
Bila gear besar berputar sekali, gera kecil
akan berputar banyak kali. Dengan
itu, gear kecil adalah adalah lebih laju
dari gera besar.
28. gear
3. Some gears move at the same position but some gears
at different position. The arrangements of gears are
important to determine the position of movement.
Sesetengah gear bergerak pada kedudukan sayang
sama tetapi sesetengah gera pada kedudukan yang
berbeza. Susunan gear adalah penting untuk
menentukan posisi pergerakan.