1. SERVICE
Before calling the service after sale, a few tips to problems.
If the LEDs light up very randomly at startup: problem DMX DMX or no connection.
-> Check the polarity, the DMX cable and the console.
One or more of the three colors are weak or off: short-circuit or overload the
installation RGB.
-> Verify that your installation does not include short-circuit or exceed the specified
power.
In the case of a short circuit, turn the power off before installing any intervention.
WARRANTY
This unit has a warranty of 12 months carry-in from the date of purchase.
SPECIFICATIONS
Height: 19mm
Width: 178mm
Depth: 46mm
Weight: 0.120 kilograms without power
Construction: PC
Input:
12VDC / 36VDC on terminal
RGBY output circuit:
Common + red - green - blue - on terminal
Max Amperage: 4 x3A
Specifications are subject to change without notice.
ALL PRODUCTS MUST BE RECYCLED WHEN THEY ARRIVE AT THE END OF LIFE.
AN ECO-CONTRIBUTION TO FINANCE THE TREATMENT OF WASTE ELECTRICAL AND
ELECTRONIC EQUIPMENT (WEEE)
DMX 4 CHANNEL RGB CONTROLER
Model No. SR-2102
GENERATOR
3x12 - 36VDC
DMX 4-CHANNEL R / G / B (0-100%)
INSTRUCTIONS - Version 1.0
READ BEFORE USE
2. Thank you for having chosen our controller A007.
CAUTION FOR USE
The generator A007 is a device intended to be used with
-lamps and circuits 3x12V DC to 36V RGBY range LED Light.
-circuits 12V DC to 36V DC monochrome range LED Light.
Using this generator with other products or for other purposes could cause irreversible
damage to the entire facility.
Before connecting the power supply, or ensure that the circuits are connected to the
voltage present.
The amperage output is available by the 3A max. LED voltage depands on the input
voltage.
The installation must be performed by qualified professionals and in our protocol.
The device is intended for indoor use only. It must be protected from moisture and
must operate at a temperature between 10 ° and 35 ° C.
Do not use the device with its housing open.
To immediately replace any damaged cable connector or by a qualified technician.
Do not repair or attempt to repair it by yourself in case of malfunction, refer to a
qualified technician.
the generator is configured to expect information DMX only. Without DMX
connection, the generator has no effect on the LEDs.
DIMMENSION
INSTALLATION
The generator can operate with either circuits or lamps 3x12V DC to DC 3x36V.
IT IS IMPERATIVE TO USE THE SAME SUPPLY VOLTAGE OF THE ELEMENTS.
Do not operate the circuit with a 12V DC power supply 36V DC or vice versa. Do not
connect elements of different voltage.
The maximum power available are:
12V IN, Each channel OUT BY: 36W max. LEDs
24V IN, Each channel OUT BY: 72W max. LEDs
36V IN, Each channel OUT BY: 108W max. LEDs
It should meet an additional reserve of 15% in the choice of powersupply
WIRING COMPONENTS RGB (No. 3 on diagram)
Use only products that operate with 12V to 36V + with the Common and color R / G / B -
-
Wire as indicated on the silkscreen in front of the camera:
Channel 1: V+ R-
Channel 2: V+ G-
Channel 3: V+ B-
Channel 4: V+ Y-
WIRING THE POWER 12V - 36V DC (No. 4 on the diagram)
Power supply 12 to 36V DC voltage corresponding to the elements RGB output.
Observe polarity (V and V +)
CONNECTING THE DMX (1 and 2 on the diagram)
DMX signal goes though terminal with Data+ and Data-, the unit has two group of the
terminal, one is for DMX signal input, the other is to another unit (max 32 generators).
The DMX address setting though button and the display.
SETTING OF THE DMX ADDRESS:
The address is obtained by pressing buttons:
Button 1: setting hundreds'digit
Button 2: setting tens'digit
Button 3: setting units'digit
DMX CHANNELS:
Channel 1: Red 0-100%
Channel 2: Green 0-100%
Channel 3: BLUE 0-100%
Channel 4: YELLOW 0-100%