Model dwl 100 series clip on digital level


Published on

A brilliant, compact instrument that clips onto your spirit level to convert it in seconds into a digital level & inclinometer. Suitable for ALL the Trades!

Accurate & simple to use, this can be used as a compact spirit level to measure true level or 90 degree plumb.

Or ALL angles in between with a 0.1 degree accuracy.

Designed to fit regular box section levels from 17mm to 23mm wide.

You can store measurements at the press of a button & the display is clear & easy to read.

It has endless uses for both the Professional & DIY'er alike.

Published in: Business, Technology
  • Be the first to comment

  • Be the first to like this

No Downloads
Total views
On SlideShare
From Embeds
Number of Embeds
Embeds 0
No embeds

No notes for slide

Model dwl 100 series clip on digital level

  1. 1. Model DWL 100 SeriesThe DWL 100 products are primarily designed for extreme convenience to be attachedon Traditional Spirit Levels,commonly available and to INSTANTLY transform theseSpirit Levels into Digital Level.Models: Clip on Models Special Feature DWL 100CWP Resolution 0.1° DWL 180CWP Resolution 0.05° Dimension L(95) x H(48) x T(32) mmScrew on models Special FeatureDWL 100S Resolution 0.1°DWL 180S Resolution 0.05°Dimension L(118) x H(48.5) x T(16) mmFeatures & Specification: Application: Measurement Range 0°~ +/- 90° High Resolution 0.05°~ 0.1° Operating Temperature 0°~ 50°C Long Battery Life with 3 minutes auto off Easy, Clear & Precise Digital Display Hold Function to Freeze Display Buzzer Sound Power supply 2 x 3v Lithium cell (Batteries included) For further information, please refer to
  2. 2. OPERATION CALIBRATION INSTRUCTION a) Batteries:Caution: Digi-Pas is calibrated in the Factory  Open the battery compartment atfor maximum accuracy. User only the rare of the Digi-Pas .recalibrate unless necessary.  Remove the small plastic from two new batteries (type AAA/LR03).1. Push ONCE on the Cal button then  Ensure correct polarity.release. Buzzer starts to beep. b) Switching on the Digi-Pas:2a. Place Digi-Pas on a flat surface (e.g.  Switch the Digi-Pas on using theTable) Use a finger to Press Mode button on/off switch.ONCE while wait a few seconds until buzzer  The Digi-Pas can measure anglesbeeps. range 0°~ +/- 90° b. Place Digi-Pas reverse horizontal (180°) c) Buzzer Sound (Acoustic signal):Press Mode button ONCE and wait a few  The Buzzer Sound are used toseconds until buzzer beeps. indicated angle of slope stands at 0°, c. Place Digi-Pas vertically (-90° and) 45° 90° , ,Press Mode button ONCE and wait a few  To switch off Acoustic signal, holdseconds until buzzer beeps. the Mode for more than 2 seconds, d. Place Digi-Pas reverse vertically (+90°) the speaker anunciator will beand Press Mode button ONCE and wait a few disappeared.seconds until buzzer beeps. d) Hold button (Memory functions)3. Calibration completes when buzzer beep  With the hold button, you cansound stops. Freeze Display for reading and the NOTE : Ensure Digi-pas is kept still during current measurement result can beCalibration saved in the internal memory.  Return to normal measuring mode by pressing Hold button  To call back the reading in the internal memory, press Hold button for 3 second. The previous save reading will be appearing in the display. e) Switching off:  To switch off the Digi-Pas, press the on/off switch (1) .When not in use more than 3 min, the Digi-Pas will switches off automatically. UK and Europe sales office TARAX TECHNOLOGY LTD First Floor, Office 2, 10 Panmure Street, Dundee, DD1 2BW. t:(+44)01382520129 m:(+44)07825041403 For further information, please refer to