2. Introduction
The aim of the project is to design an automated system that
controls the movement of car using DTMF tone, in case if car is
stolen.
In this system, if there is any unauthorized switching on of car,
the mobile attached to car's system will automatically dial up the
last number.
As the caller of the number picks the call, he presses a certain
button and car's ignition goes off.
9. In addition to the full wave rectifier circuit ,we
have added, a voltage regulator to maintain the
output voltage at 5V.
the capacitor(uf) nullifes the effect of the
voltage regulator.
10. DTMF decoder
DTMF keypad frequencies (with sound
clips)
1209
Hz
1336 H
z
1477 H
z
1633 H
z
697 H
z
1 2 3 A
770 H
z
4 5 6 B
852 H
z
7 8 9 C
941 H
z
* 0 # D
11. DTMF Decoder
Dual-tone multi-frequency signaling (DTMF) is used for
telecommunication signaling over analog telephone lines in
the voice-frequency band
The DTMF system uses eight different frequency signals
transmitted in pairs to represent sixteen different numbers,
symbols and letters
The DTMF keypad is laid out in a 4×4 matrix.
DTMF is basically a signal to the phone company that you
generate when you press an ordinary telephone's touch keys
12. Creating circuit having H-bridges
which drives the motor.
To control a movement of the dc motor we require a H
bridge circuit.
H bridge is a combination of the 4 transistor circuit.
Two transistor’s are npn and two transistor’s are pnp
transistor.
With the help of this four transistor circuit we control
the movement of the motor automatically.
14. Creating Auto Dial-up circuit relay
logic .
Using this relay logic,handsfree redials the last
number store in the mobile.
Relay logic is used for the autodialup circuit.
we connect a one relay coil with the controller with two
transistor circuit.
16. Methodology
Case 1: When
intruder presses
the start switch
Case 2: When
the sensors
detects anything
Autodiallin
g circuit
activated
17. Proposed Plan
• 1st-2nd weeks – Literature Survey
• 3rd week – Component study
• 4th week – Procuring Component
• 5th-6th week – Study of embedded language
• 7th week – Circuit design
• 8th week – circuit implementation and corrections (if any)
• 9th -10th week – Microcontroller Programming
• 11th-12th week – Hardware implementation
• 13th-14th week – Final project report, model and presentation
submission
18. Future Aspects
We can add multiple sensors apart from the one we
have already used.
a) One of them being motion sensor which will
comprise of reciever, transmitter and modem.
b) Since we are also using a cell phone in our
project, the cell can be also used as a GPS navigator.
c) A smart mobile charging function can also be
added in the circuitry.
19. REFERENCES
http://www.atmel.com/dyn/resources/prod_documents/doc2487.pdf - for
details of 8951 MC
http://www.keil.com/dd/docs/datashts/atmel/at_c51ism.pdf - instruction set
of atmel 89s
http://www.pcbased.in/8051-microcontrollers/89s51-architecture-instruction-
set-tutorials--89S51-microcontrollers.asp - PIN DESCRIPTION OF 89S51
http://www.siongboon.com/projects/2005-07-18_dtmf_circuits/ - for dtmf ic
8870
http://www.digchip.com/datasheets/download_datasheet.php?id=541970&par
t-number=M-8870 - for studying 8870
http://www.freewebs.com/maheshwankhede/dtmfdecoder.html - interfacing
8051 with dtmf decoder
http://www.societyofrobots.com/robotforum/index.php?topic=4786.0 - forum
on robotics discusing dtmf use
www.tech-faq.com/dtmf.html - studying dtmf
http://www.intlsensor.com/fumigation.html - gas sensor
http://www.doctronics.co.uk/555.htm
