1. LED Aging Table(tube.bulb)
2. LED Lock Crimp Machine
3. LED Rework Station
4. LED Test Power Supply(DC)
5. LED Driver Test Stand
6. Desktop Lamp Base Crimping Machine
7. LED Pressure Riveting Machine
8. Wire Cutting and Stripping Machine
9. LED Bulb Capping Machine
For More SMT Equipments Plz Contact at etasmt@foxmail.com or eta@eta-ele.com (Shanny)
WebSite: www.smt11.com
1. 1 LED Auxiliary Products introduction | ETA
www.smt11.com
Full LED solution provider
LED Auxiliary Equipment
Introduction
LED Aging Table(tube.bulb):
1.The main structure of test bench adopts 4040 industrial aluminum structure.
2. The external dimension is approx. 2400*500*1900mm(H),the width of lamps test bench
installation part is 2000mm,the width of control cabinet part is 400mm.Equipped with
supportable truckle, making it easy to move and fix.
3. Each lamp test bench match up with independent control cabinet, PLC+ touch screen
control method, making it convenient to set and adjust normal open, on and off working
mode, on and off time setting, total, test time setting, adjusting power output voltage of
each layer and other parameters value.
4. Each layer(or each column of the stent lamp) power supply independently, in the position
of power supply into lamp, each layer(or each column of the stent lamp) are equipped with
protective air switch, realizing jumping off when abnormity arises;
6. The lamp test bench control power supply and life aging power supply are separately installed, the life aging power supply leave a special
interface, convenient for external AV power supply, stabilized voltage supply, voltage regulator or set file output transformer.
LED Lock Crimp Machine:
1.Pneumatic crimping lights, Automatic counting, has automatic punching and
semi-auto transfer swith ,when in automatic switch just input the lamp cap
into the hole ,then it automatic start punching .when use semi-auto
switch ,use you foot to control it .
2.This equipment is applicable to a variety of LED/CFL lamp manufacturer,
lamp and plastic head for the combination of clamping, the use of
machine-driven cylinder and head combinations, E27 lamp,E14 lamp ,B22
lamp special fixing equipment, which is stable, secure, convenient and quiet.
3.Frames:Made of 40×30mm rectangle steel pipe, Protective board is made of
2.0mm cold steel sheet by bending.
4.Air cylinder:Made of base crimping machine of energy saving lamp special air cylinder, 12 air cylinders, 12 Fixing special needles.
5.Electric traceway:Automatic puching or semi-auto optional, automatic counting. Easy to control.
6.Speed: 0.3-1 seconds per pieces .
LED Rework Station:
1.digital display screen
2.room temperature -400 C temperature can be arbitrarily set
3.heating plate using high quality imported aluminum alloy, high density, good thermal conductivity,
temperature uniformity.
4.the temperature control part uses the intelligent microcomputer PID chip, has a key to self adjust
2. 2 LED Auxiliary Products introduction | ETA
www.smt11.com
Full LED solution provider
and save function, phase shift trigger control, temperature is stable, energy saving.
5.high quality ceramic heating body, can work in high temperature environment for a long time
LED Test Power Supply(DC):
1. High precision LED digital display, intuitive and clear.
2. Double temperature control fan, good heat dissipation effect, effectively prolong the life of fan,
reduces the noise.
3. Voltage multi ring potentiometer adjustment, make the output more accurate.
LED Driver Test Stand
1.can accurately measure the driving load voltage supply.
2.can accurately measure the power supply voltage to drive the load , the output current and voltage
single lamp beads .
3.you can test the finished lamp is lit and power .
4.you can test the finished product without cap lamp is lit and power .
Size : 300 * 200 * 67MM
Maximum measurable current : Do not exceed 2A ( the presence of 5% of the float )
The maximum measured load voltage : 200V
Maximum measurable power : 100W
Desktop Lamp base crimping machine
1.Use high quality cylinders, the depth of punching needle can be adjustable .
2.Adopt High quality ,high speed ,harden needles ,hardness>=60%.
3.With function of Automatic counting the number of punching lamps .
4. 3-4mm distance electromagnetic induction then punching .
5.With automatic and semi-atomatic switch ,you can choose the way you want .
6. Two conjoined air filter processor inside to dry the air .
7.Weight: about 35 kgs .
LED Pressure riveting machine
1.with the needle guide bar which ensure a steady stroke
2.small pressure appearance, high noise small-scale production efficiency
3.pressure adjustable time 0 to 10 seconds, to ensure product quality
4.the most suitable for mass production efficiency to reduce the cost of production
3. 3 LED Auxiliary Products introduction | ETA
www.smt11.com
Full LED solution provider
Wire Cutting and Stripping Machine
1.Widely used in cutting,stripping,Max conductor sectional: 10mm2
2. LED display,hybrid motor drive,Multi-function setting
3. workable wire PVC,Teflon,Braided wire
4. Exquitsite and compact design, extremely excellent conception, small footprint.
5. Touched computer operation screen make it easy to learn to operate.
6. Changing procedure & Materials rapidly
4. High-efficiency step drive, high-accuracy and fast speed.
LED Bulb Capping Machine
1. Compressed air as power source can be applied to manual operation and automatic pipelining.
2. Simple structure, easy operation, low price and superior performance.
3. according to different products or mold, adjust height, speed, stroke, pressure and stamping time.
4. You can choose a two hand control button or a foot switch.
5.used for led bulb A60,A65,A70 etc.
Thanks for choosing ETA.