TOOLS AND EQUIPMENT FOR WOOD, METAL, AND BAMBOO CRAFT
DICTIONARY MECHANICAL
1. Angle
An angle is a flat metal bar Which is bent at an
angle of 90 degrees along SIT length, RESULTING in
an L-shaped angle piece Normally Both Sides are
of equal length. The angle is Often heavy structural
element in buildings, bridges, and so on, while the
lighter is used for a variety of media.
3. ANGLE OF 45 ° and 90 °:
• It is an instrument used to give dimension to
any room, and is also useful when creating
angles of either 45 ° or 90 °
•
4. Awl
• It is called a center punch hand tool shaped
sharpening hardened steel pointer at one end
with a tip of about 60 which is used to mark
the exact spot that was previously drawn on a
piece where a hole has to be made
5. Anvil
• An anvil is a tool blacksmith. It is made from a
solid block of stone or metal used as a support
to forge metals such as iron or steel. The
weight of a blacksmith's anvil normally
between 50 and 200 kg,
6. Burner gas
• Torch or torch aka burner gas or propane
lantern, its main use is to soften and remove
old paint and welding metals. Modern burners
are provided with liquid gas tanks normal
temperature vaporizing as the pressure is
released through valve operation. The most
ancient torch used as fuel gas.
7. Brush
• The brush is a brush that collects between the
fibers retaining certain material and then
uniformly distributed on a surface. This
material may be liquid or powdery
8. Bank for welding
• The bank for welding and modular panel for
welding tools and accessories are the perfect
individual work station when welding with
maximum guarantees of success.
9. Bench grinder
• The bench grinder is a tool to sharpen tools
and clean metal. A bench grinder can make
the edge of the square and tools acutely
repair screwdrivers, wicks and tips punches.
10. Bit
• The bit is a metal piece that creates cutting
holes in various materials when placed in a
power tool as a drill, auger or other machine.
Its function is to form a hole or cylindrical
cavity.
11. Bolt
Bolt piece of iron or other metal, long,
cylindrical, with round head at one end and
secured with a cotter pin, nut or rivet on the
other, used to say high volume parts.
12. Chisel
• It is called chisel to a manual cutter or marking
consists of a tempered steel bar ending in a tip with
a handle shaped knob which serves mainly to cut,
mark, grooving or grinding material cold by the blow
with a suitable hammer or by pressure with the palm
of the hand.
13. Chisel
• Chisel: A special fine chisel to make
rectangular holes or escopladuras or boxes.
•
14. Chisel
•
• Chisel: A cutting tool like a chisel but used to
split, cut or make holes in metals.
15. CPress
• C Press in its utility is to hold and squeeze a
particular piece to be taken to a process in
order to give better results to the job, as there
are some things thact are necessary to
sustain.
16. Chainsaw
• Chainsaw makes cutting operations,
considering that are possible to do in inclined
plane, in short no matter where cutting tilt
want to cut. then a sample.
18. Caliper guage
• It is an instrument to measure outdoor indoor,
among other dimensions , based on convertion
systems such as desimal metric system and
english system
19. Drill
• The drill is a machine tool where most of the holes are made in the
mechanical parts are machined workshops. These machines stand out for
the simplicity of handling. They have two movements: The rotation of the
bit that gives it the electric motor of the machine through a transmission
pulleys and gears, and the advancement of penetration of the bit, which
can be done manually or automatically sensitive if he uses transmission to
do so.
20. Disk grinder
• Disk grinder
Superfine aluminum oxide disc for cutting
metal. Is 115 mm in diameter and a height of
0.8 mm tablet
21. Drill
• Electric screwdriver an advanced and modern
version of the traditional drill. The latest
models are powered by rechargeable batteries
that provide greater freedom of movement,
although there with cables.
22. Electric sanders
• Electric sanders the main advantage of using electric sanders is that a
working speed set is obtained, and that do not require expensive facilities
to maintain, contrary are sanders high weight, noisy and that steps need
to be taken to prevent referrals or shock during use.
23. Electric Sander
• Electric Jig Saw is a lightweight tool for straight,
circular and oblique cuts. The leaflets are
interchangeable, depending on the material to be
used: cardboard sheets, gypsum, thin metal plates.
24. Earmuffs
• Earmuffs consist of a head harness of metal
or plastic that holds two caps made mostly of
plastic. The device completely encloses the
ear pavilion and tightly applied to the head by
a foam pad or fluid-filled
25. Electrode
• One electrode is an electrical conductor used
to make contact with a metal part of a circuit,
such as a semiconductor, an electrolyte, a
vacuum, a gas, etc.
26. Expancion key
• Expancion key serves to set and loosen nuts
of different diameter, provided that particular
dimencion scope.
28. Flexometro
• The tape measure is a measuring instrument which is agree
with the name of tape, with the addition that is constructed
from a thin flexible strip, divided into units of measurement,
and it is rolled inside a metal casing or plastic
29. flange nuts
• flange nuts
A flange nut is a nut having a wide flange at
one end which acts as a, integrated non-
rotating washer.
•
30. Grooved
• Grooved or hollow chisel chisel is a tool to open channels and
slots for gas pipes and water and power lines in different
materials (except granite and marble). The grooved chisel is
preferred for softer materials construction. Being slightly
angled, can be kept constant groove depth more easily with
the hollow chisel.
31. Goniometer
• Goniometer (instrument). It is a measuring
instrument used to measure angles, checking
cones, and tuning of machine tools machine
shops.
32. Glove
• The glove is a garment whose purpose is to
protect the hands or the product to be
handled.
•
33. Garment leather
• Garment leather or heavy cloth, which, around the neck,
served in certain trades to protect clothing from above the
chest to below the knees:
• had the tools in the pockets of her apron
34. Hammer
• The ball peen hammer is a tool steel
combined percussion and wooden handle or
fiber cylindrical surface flat head and blow.
35. Horizontal milling
• iscalled a horizontal milling unamáquina-
herramientautilizadafordiferentesmecanizadosporstartdevirutaenprismati
cparts. This type of machine is characterized by work in space through
proper movement lamesa where the parts to be machined are fixed. This
table can move alo along three different movements: Longitudinal,
transverse and vertical.
36. Industrial diss
• Disco industrial diamond dust for fine cutting
supplies. Has diameter 230 mm and a height
of 22.2 mm tablet.
38. Key in L
• Key in l is used for tightening and loosening
bolts that are inside hexagonal shaped
quadrant.
39. Level
• Level (instrument). It is a measuring instrument used to
determine the horizontal or vertical position of an element.
There are different types and are used by surveyors,
carpenters, masons, blacksmiths, aluminum worker
40. Lacquer
• In a broad sense the lacquer is a relatively inaccurate to refer
to a termination liquid light wood or colored that dries by
solvent evaporation term. It is often also a curing process that
produces a hard, durable surface finish.
41. Mazas
• Mazas: These hammers with wooden head,
nylon, rubber, etc. They are used to hit on soft
materials that can be marked. Are typically
used to hit other tools and to shape sheets.
•
42. Mandrel
A mandrel is a special type of press used to hold
an object, usually a radially symmetrical
object, especially a cylindrical object.
•
43. Machine shaper
• In this machine shaper grinding processes are
performed, are made screw heads, nuts.
where at one point the presicion of certain flat
regions is necessary and curvas.acontinuacion
have a sample.
•
44. Male
• Male only serves to hold any kind of object
that fence to be subjected to a mechanical
process, either a cut or tightening and
loosening of this.
45. Metal Putty
• Metal Putty 250Gr Aprox.20-30 min after
sanding Asbestos and silicone free, smooth
and thixotropic.Adding hardener:
4.2%.Resistance to acids, alkalis, water and
salts.Resistant to temperatures of 120 ° C.
46. Milling machine
• A milling machine is a machine tool used for
machining by chip removal by moving a rotary
tool cutting edges of several known
strawberry
47. Oxyfuel
• Oxyfuel welding and in this type of welding, as
well as in flame cutting, the heat source
comes from the combustion of a gas, often
acetylene.
48. Pliers
• Cutting pliers used to cut cables or wires,
which is why they are lined with rubber to
shield against the current.
•
49. Pliers Universal
• Universal Pliers this tool can be found in
different measures 160 mm long, 180 mm or
200 mm. Universal pliers have narrow and
thick jaws that facilitate straight and curved
cuts in metal sheets.
50. Paint gun utensil
• Paint gun utensil comprising a container and a
mechanism for spreading a certain pressure
on a liquid surface: water gun; glue gun; liquid
paint gun
51. Paint
• The paint is a fluid product which, when
applied on a surface in relatively thin layers, is
transformed over time in a solid film which
adheres to said surface, so that covers,
protects and decorates the element on which
it is applied
52. Parallel
• The parallel or lathe lathe is the type that
evolved based on ancient lathes when you
were able to incorporate new equipment that
make it one of the most important machine
tools that have been
53. Pliers
• Pliers: These are special tools to remove nails,
are not therefore true clamping tools,
although sometimes used as such.
55. Rivet
• A rivet is a rivet or fastener to be used to permanently join
two or more pieces. It consists of a cylindrical tube (stem)
which at its end has a head. The heads have a larger diameter
than the rest of the rivet, so that when inserting it in a hole
can be tapped. The use that is given is to join two different
pieces, whether or not of the same material
56. Ring
• Ring gear steel cylinder on one end has teeth
and the other end connects to the drill.
57. Strawberries
• Strawberries are cutting tools shape, material and size varied
according to the type of routing you want to perform. A
strawberry is determined by its diameter, shape, constituent
material, number of flutes or teeth you have and the restraint
system to the machine.
58. Square
• The try square is a tool for work in carpentry
or metalworking, used for marking and
measuring a piece of material.
59. Spike
• Spike for welder is a tool with spring handle
and two opposite mouths, as a flat hammer,
and another sharp peak and is used to remove
welding slag.
60. Safety glasses
• Safety glasses, goggles or goggles are a form
of protective eyewear that are normally used
to prevent foreign objects, water or chemicals
on the eyes.
61. Scissors
• Unior scissors to lamina are made of carbon
steel with forged ends and induction
hardened cutting edges.
62. Tip marker
• Tip marker or scorer is a sharp steel instrument that
is used to mark a line on a metal surface. The
simplest has a single point and a knurled grip easier
to hold. The most elaborate skimmers are two
points, whether fixed or replaceable.
63. Thinner
• The diluents (thinner in English), also known
as paint thinner or depressant is a mixed
solvent of organic nature petroleum that has
been designed to dissolve, dilute or thin
water-insoluble substances such as paint, oils
and fats.
64. U Bolt
• Piece of metal, typically U-shaped, perforated at their ends
traversed by a pin called worm.
It is used to join or say something.
Measure from the string anchor with 25 m in length.
65. U Joint / Universal Joint
• The gimbal or, in Spain, pronounced cards, is a mechanical
component, first described by Girolamo Cardano, which
allows joining two non-collinear axes. Its objective is to
transmit the rotational movement of a shaft to the other
66. Voltmeter
• A voltmeter is an instrument used to measure
the potential difference between two points in
an electric circuit.
67. Welding Machine
• A welding machine is a tool that is used
mainly for joining pieces, by applying heat
69. Zigzag Spring
• A zigzag1 is a pattern composed of small
corners in variable angle, but constant in the
zigzag, tracing a path between two parallel
lines, which can be described as irregular and
regular
70. Zinc Coated Steel Sheet
• What is the galvanized sheet?
Share on FacebookShare on EmailShare on twitterShare on Printmore
Sharing Services
Sheet is a galvanized steel sheet which has undergone a hot dip process
the sheet covering 100% of zinc, in order to prevent corrosion.
The galvanized steel sheets have a number of applications in construction,
automobile manufacturing tools.