Fiber optic patch cable as the basic element of a network, transmits signals through strands of glass or plastic fiber. Fiber optic cables are available in multimode and single-mode fibers terminated with LC, SC, ST, LC, FC, MTRJ, E2000 connectors in simplex and duplex. The typical multimode fiber used in telecom or datacom applications has a core size of 50 or 62.5 microns. Single-mode fiber shrinks the core size down to 9 microns so that the light can only travel in one ray.

1. WHITE PAPER
Fiberstore (FS.COM) | Fiber Type and Corresponding Optical Transceivers
Fiber optic patch cable as the basic element of a network, transmits signals through strands of glass
or plastic fiber. Fiber optic cables are available in multimode and single-mode fibers terminated with
LC, SC, ST, LC, FC, MTRJ, E2000 connectors in simplex and duplex. The typical multimode fiber used
in telecom or datacom applications has a core size of 50 or 62.5 microns. Single-mode fiber shrinks
the core size down to 9 microns so that the light can only travel in one ray. Different fiber types like
multimode or single-mode fibers connect with fiber optic transceivers resulting in different
performances, which makes a huge impact on the network application. Here is what you need to
know about the fiber types and the corresponding optical transceivers for network infrastructure.
Internal Structure of Fiber Optic Cable
An optical fiber is a flexible filament of very clear glass capable of carrying information in the form
of light. Single-mode fiber optic cable has a small diametral core of 9/125 microns that allows only
one mode of light to propagate, which results in light reflections, lower attenuation and creating the
ability for the signal to travel faster, further. That’s why single-mode fibers are typically used in
long-reach applications.
MM fiber patch cords, however, has a large diametral core of 50/125 and 62.5/125 in construction
that allows multiple modes of light to propagate. Therefore, the number of light reflections created
as the light passes through the core increases, creating the ability for more data to pass through at a
given time. Because of the high dispersion and attenuation rate with this type of fiber, the quality of
the signal is reduced over long distances. The above picture shows the inner structure of fiber optic
cables.
Fiber Type and
Corresponding Optical
Transceivers

2. WHITE PAPER
Fiberstore (FS.COM) | Fiber Type and Corresponding Optical Transceivers
Factors When Choosing Single-mode or Multimode Fiber
Different core diameters of single-mode and multimode fiber optic cables affect the optical
properties and have a direct impact on system performance. Besides this, other factors like
bandwidth, attenuation and costs also have the biggest impact on the system performance. Figure 2
gives you a vivid description of single-mode and multimode fiber.
Attenuation is the reduction of signal power, or loss, as light travels through an optical fiber. Fiber
attenuation is measured in decibels per kilometer (dB/km). The higher the attenuation, the higher
rate of signal loss of a given fiber length. Single-mode fibers generally operate at 1310 nm (for short
range) while multimode fibers operate at 850 nm or 1300 nm. Attenuation is not usually considered
to be the main limiting factor in short rang transmissions. But it can cause big differences in high
speed network such as 100Gb/s.
Bandwidth means the carrying capacity of fiber. For single-mode fiber, the modal dispersion can be
ignored since its small core diameter. Bandwidth behavior of multimode fibers is caused by
multi-modal dispersion during the light traveling along different paths in the core of the fiber. It has
an influence on the system performance and data rate handling. Multimode fiber uses a graded
index profile to minimize modal dispersion. This design maximizes bandwidth while maintaining
larger core diameters for simplified assembly, connectivity and low cost. So manufacturers start to
develop higher-performance multimode fiber systems with higher bandwidth.
Costs: A fiber optic transceiver usually consists the optical light sources, typically LED–light emitting
diode and optical receivers. Since the core diameter size and primary operating wavelengths of
single-mode fiber and multimode fiber are different, the associated transceiver technology and
connectivity will also be different. So is the system cost.
To utilize the single-mode fibers generally for long distance applications, transceivers with lasers
that operate at longer wavelengths with smaller spot-size and narrower spectral width. But these
kinds of transceivers need higher precision alignment and tighter connector tolerance to smaller

3. WHITE PAPER
Fiberstore (FS.COM) | Fiber Type and Corresponding Optical Transceivers
core diameters. Thus, it causes higher costs for single-mode fiber interconnections. To lower the
cost, manufacturers produce transceivers based on VCSEL (vertical cavity surface emitting laser), for
example, 10G-SFPP-SR is a SFP+ transceiver support a link length of 300m, which are optimized for
use with multimode fibers. Transceivers applying low cost VCSEL technology to develop for
50/125μm multimode fibers, take advantage of the larger core diameter to gain high coupling
efficiency and wider geometrical tolerances. OM3 and OM4 multimode fibers offer high bandwidth
to support data rates from 10Mb/s to 100Gb/s.
Fiber Type and Associated Optical Transceiver Compatibility Matrix
From a technician standpoint, optical transceivers should be compatible with fiber optic cables,
meaning that multimode transceivers should only connect with multimode fiber optic cables, or you
may end up with an error. Table 3 summarizes various optical interfaces and their performance over
the different fiber types. The table specifies the maximum reach achievable over each fiber type
and the requirement for a mode conditioning patch cord.
This table is directly derived from the IEEE 802.3-2005 standard, if you comply with the standard,
these performances are guaranteed and longer reaches may be achievable depending on the
quality of each link. To ensure whether a link can work, all you can do is to try and see if the
performance is satisfactory. The link should be either error-free for critical applications, or the bit
error should remain below 10-12 as per minimum standard requirement. For instance, it may be
possible to reach much longer distances than 550 m with an OM3 laser-optimized fiber and
1000BASE-SX interfaces. Also, it may be possible to reach 2 km between two 1000BASE-LX devices
over any fiber type with mode conditioning path cords properly installed at both ends. Single mode
fiber patch cables as noted before, are suitable for long-haul application. Although the optics are
more expensive, they’re offering much longer reach, which makes them an ideal choice for network
infrastructure.

4. WHITE PAPER
Fiberstore (FS.COM) | Fiber Type and Corresponding Optical Transceivers
Conclusion
Choosing the right fiber for your network application is a critical decision. Whether to use
single-mode or multimode fiber for your infrastructure, no one can give your the best answer. Only
by fully understand the system requirements and select the appropriate fiber can you maximize the
value and performance of your cabling system. FS.COM offers cost-effective fiber optic patch cables
to meet the requirements of all the customers. If you are interested, please send your request to us.

5. WHITE PAPER
Fiberstore (FS.COM) | Fiber Type and Corresponding Optical Transceivers
Contact Us
Manufacturing R & D (China)
Eastern Side, Second Floor, Science &
Technology Park, No.6, Keyuan Road,
Nanshan District, Shenzhen 518057,
China
Tel: +86 (755) 8300 3611
Fax: +86 (755) 8326 9395
Email: sales@fs.com
APAC Office (Hong Kong)
1220 Tung Chun Commercial Centre,
438-444 Shanghai Street, Kowloon,
Hong Kong
Tel: +852 81763606
Fax: +852 81763606
Email: sales@fs.com
North America (United States)
331 Andover Park East Ste330, Tukwila,
WA 98188,United States
Tel: +1-425-226-2035
Fax: +1-253-246-7881
Email: sales@fs.com
London Office (United Kingdom)
Third Floor 207 Regent Street, London,
W1B 3HH, United Kingdom
Tel: +44 2081441980
Notice: This document is for informational purposes only and does not set forth any warranty, expressed or
implied, concerning any equipment, equipment features, or service offered or to be offered by Fiberstore.
Fiberstore reserves the right to make changes to this document at any time, without notice, and assumes no
responsibility for its use. This information document describes features that may not be currently available.
Contact a Fiberstore sales team for information on feature and product availability.
Follow us
LinkedIn
Twitter
Facebook
G+
Pinterest
Youtube
Blog