1. Amir Jawaid Arian
H.no2612 Shah Latif colony Kotri
923455761367
E-mail: arainamir@ymail.com
Introduction:
A Masters Degree holder in Petroleum Technology from the UK, possess multidimensional 14 years experience
in Dewan Salman Fibre Ltd., Pakistan’s largest Polyester Staple Fibre manufacturing facility; a joint
venture between Mitsubishi Corporation of Japan, Sam Yang Co. of Korea and Dewan Mushtaq group.
Participated commissioning and pre- commissioning activities at UCH 2 GAS Amine Sweetening unit
300 MMSCF/ Day capacity, with OGDCL and ENAR Team,working in H2S Environment and its safety
measures ,
Qualifications:
M.Sc. Petroleum Technology: School of Science & Technology, University of Teesside, United Kingdom
Core Modules: Health and Safety, Process Simulation and Economics, Fire sciences, Petroleum
Chemistry, Hydrocarbon Operation, Modelling.
Dissertation: Economic benefit by Health and Safety Importance of Health and Safety by making
appropriate policy which is economically beneficial for an Organization.
B.E. Chemical: NED University of Engineering & Technology, Karachi, Pakistan
Major Subjects: Unit operations, Heat and Mass transfer, Fluid Dynamics, Thermodynamics, Plant
Design and Economics, Fuel and Furnaces.
Dissertation: Recycling of Waste Paper and Designing of related equipment
Professional Experience:
Working for OGDCL uch 2 commissioning Team at 300 MMSCFD Plant Amine sweetening unit from jan
2012 to till date for ZEL Engineering . participated in all activities of erection and pre -commissioning and
commissioning activities
Water flushing of equipment , air blowing ,internal inspection and installation of equipment,conformity
Check,utility system set up,Amine drain system set up,instrument air and nitrogen gas system, fuel gas system
and flare gas system , leak test, nitrogen purging , incinerator start up, Refractory curing/dry out start-up with fuel
gas , preparation of Amine solution, pressurization , Loading of Amine solution,
Start up procedure,formulated Amine solution loading , process gas pressurization and set up,Amine circulation at
minimum flow,Steam vapor circuit set up,cooling water circuit set up,Achievement of normal operating
conditions ,Establishment of gas flow, strat up and control system tuning ,Hook up of ESDV,S,Control valve ,and
BDV,S , PSV calibration and installation instrument loop versification, stoke test , Solo run test of all motors
Assistant Manager SEP 2006 TO JAN 2009
Meeting with clients ,train the staff in different location for different clients, provide HSE Training
Safety drills, ISO9001,14001,18001,,Trough lecture ,assist clients in calibration, Environmental testing provided
according to international standards, testing of smoke detectors, fire alarms,,
Shift Engineer: Dewan Salman Fibre Limited, Haripur, Pakistan Dec 2000 – Aug 2006
1 | Page

2. • Ensuring compliance with applicable HSE Rules, Regulations and Standards.
• Well versed with the Work Permit System.
• Participating in HAZIDs and HAZOP studies, detailed Risk and Reliability analyses, Consequence Studies,
Fire Protection Studies, etc.
• Reviewing Design briefs, reports, P&IDs and Safety System Design material and providing expert advice.
• Responsible for incident investigation, trouble shooting, root cause analysis and to recommend solutions to
prevent recurrence.
• Conducting Emergency drills.
• Ensuring overall plant Housekeeping as per Health and Safety requirements.
• Participating in HSE meetings.
• Hand on experiences on DCS (Distributed Control System) of a continuous Polymer Plant.
• Multi-dimensional experience of Operations and Technical Services, capable to work effectively within
a multi-discipline team environment.
• Ensuring that key process parameters and their trends are normal, process security system is intact and
security bypass and normalization timings are logged properly with reasons. Advising corrective measures in
case of any abnormality.
• Supervising and controlling operations and maintenance activities, responsible for synergy in operations of
process area, utilities, material movement, laboratory, HSE, security, maintenance and telecommunication.
Polymer plant annual turnaround shut down and starts up planning, execution, internal equipment observation,
etc.
• Monitoring of Schedule Switching and ensuring the availability of Stand-by Equipment.
• Interaction with services department and communication with higher management.
• Responsible for energy management for all units by managing steam turbines and motor driven machinery
and boiler load regulation in shifts.
• Technical staff management, training needs identification, recommendation, and after training assessment.
• Worked as member core team for certification of ISO-9001, OHSAS-18001 and EMS-14001.
• Review and approval of Environment and OHSAS-18001 study.
• Waste water disposal at plant according to environmental standards.
Professional Training:
• Safety Control and Loss Prevention - DSFL
• Industrial Pollution and Waste disposal - DSFL
• Fire Safety Courses
• Health and Safety Courses
Skills:
• Effective interpersonal and communication skills, supervision, effective decision making, strong emotional
stability, self-regulation, social skills and technical report writing.
• Computer literacy: Proficient in Windows environment well versed in Microsoft Office Suite and Microsoft
Project. Confident in utilizing Internet and Technology to supplement the day-to-day work related needs.
Engineering Software:
• HYSYS (Oil Manager)
• Mini Tab
2 | Page

3. Professional Membership:
• Member of Engineering Council of Pakistan and IChemE (Student Membership)
References:
• Available on request
3 | Page