The document describes the configuration of two routers, R1 and R2. On each router, serial interface S0/0 and Fast Ethernet interface F0/0 are configured with IP addresses and enabled. Ping tests are then able to reach the IP address of F0/0 on R1, indicating basic connectivity is established between the two routers.
1. R1
Router Con0 is now available
Press RETURN to get started!
Router>enable
Router#confi
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#inter
Router(config)#interface s0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.1.1 255.255.255.0
Router(config-if)#clo
Router(config-if)#clock r
Router(config-if)#clock rate 64000
Router(config-if)#no shut
Router(config-if)#no shutdown
11:08:56 %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
11:08:56 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed
state to up
Router(config-if)#exit
Router(config)#con
Router(config)#con
Router(config)#conf
Router(config)#config t
Router(config)#config ter
Router(config)#config
Router(config)#inter
Router(config)#interface F0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.101.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
11:10:20 %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
11:10:20 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,
changed state to up
2. Router(config-if)#exit
Router(config)#
R2
Router Con0 is now available
Press RETURN to get started!
Router>enable
Router#con
Router#confi
Router#configure ter
Router#configure terminal
Enter configuration commands, one per line. End with CNTL/Z
Router(config)#inter
Router(config)#interface s0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.1.2 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
11:11:41 %LINK-3-UPDOWN: Interface Serial0/0, changed state to up
11:11:41 %LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed
state to up
Router(config-if)#exit
Router(config)#inter
Router(config)#interface F0/0
Router(config-if)#ip add
Router(config-if)#ip address 192.168.100.1 255.255.255.0
Router(config-if)#no sh
Router(config-if)#no shutdown
11:12:24 %LINK-3-UPDOWN: Interface FastEthernet0/0, changed state to up
11:12:24 %LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/0,
changed state to up
Router(config-if)#exit
3. Ping
Microsoft Windows 2000 [Version 5.00.2195]
(C) Copyright 1985-1999 Microsoft Corp.
C:>ping 192.168.101.1/24
Unknown host 192.168.101.1/24
C:>ping 192.168.101.1
Pinging 192.168.101.1 with 32 bytes of data:
Reply from 192.168.101.1 ;bytes=32 time=22ms TTL=254
Reply from 192.168.101.1 ;bytes=32 time=22ms TTL=254
Reply from 192.168.101.1 ;bytes=32 time=22ms TTL=254
Reply from 192.168.101.1 ;bytes=32 time=22ms TTL=254
Ping Statistics for 192.168.101.1:
Packets Sent = 4, Received = 4, Lost = 0 (0% loss),
Approximate round trip times in milli-seconds:
Minimum = 22ms, Maximum = 23ms, Average = 22ms
C:>