Best practice manual hvac chillers

5,596 views
5,363 views

Published on

Published in: Technology, Business
0 Comments
9 Likes
Statistics
Notes
  • Be the first to comment

No Downloads
Views
Total views
5,596
On SlideShare
0
From Embeds
0
Number of Embeds
6
Actions
Shares
0
Downloads
591
Comments
0
Likes
9
Embeds 0
No embeds

No notes for slide

Best practice manual hvac chillers

  1. 1. BEST PRACTICE MANUAL HVAC-CHILLERS Prepared for Bureau of Energy Efficiency, (under Ministry of Power, Government of India) nd Hall no.4, 2 Floor, NBCC Tower, Bhikaji Cama Place, New Delhi – 110066. Indian Renewable Energy Development Agency, Core 4A, East Court, st 1 Floor, India Habitat Centre, Lodhi Road, New Delhi – 110003 . By Devki Energy Consultancy Pvt. Ltd., 405, Ivory Terrace, R.C. Dutt Road, Vadodara – 390007, India. 2006
  2. 2. CONTENTS 1 I N T R O D U C T I O N ............................................................................................................................. 4 REFRIGERATION & AIR-CONDITIONING ................................................................................................. 4 THE NEED FOR RADICAL THINKING ...................................................................................................... 4 1.1 1.2 2 REFRIGERATION & AIR CONDITIONING SYSTEMS......................................................................... 5 2.1 2.2 2.3 2.3.1 2.3.2 2.3.3 2.3.4 2.3.5 2.3.6 2.4 2.5 2.5.1 2.5.2 2.6 2.6.1 2.7 2.7.1 2.8 3 STRATEGIES AND OPPORTUNITIES FOR ENERGY SAVING ....................................................... 31 3.1 3.2 3.3 3.4 3.5 3.6 3.7 3.8 3.9 3.10 3.11 3.12 3.13 3.14 4 MINIMISING REFRIGERATION & AIR-CONDITIONING .............................................................................. 31 OPERATING AT HIGHER EVAPORATOR TEMPERATURE ......................................................................... 32 ACCURATE MEASUREMENT AND CONTROL OF TEMPERATURE .............................................................. 33 REDUCTION IN HEAT LOADS ............................................................................................................. 34 MINIMISING HEAT INGRESS ............................................................................................................... 34 REDUCING VENTILATION HEAT LOAD ................................................................................................. 38 USING FAVOURABLE AMBIENT CONDITIONS ....................................................................................... 39 USE EVAPORATORS AND CONDENSERS WITH HIGHER HEAT TRANSFER EFFICACY ................................. 40 ENERGY SAVING OPPORTUNITIES IN NORMAL OPERATION ................................................................... 41 MAINTENANCE TO ENSURE ENERGY EFFICIENT OPERATION ................................................................. 43 ENERGY SAVING IN LOW RELATIVE HUMIDITY AIR CONDITIONING ......................................................... 44 DESUPERHEATER FOR RECOVERING CONDENSER WASTE HEAT .......................................................... 45 INTER-FUEL SUBSTITUTION: ELECTRICITY SAVINGS BY USE OF ABSORPTION CHILLERS ......................... 45 GENERAL TIPS TO SAVE ENERGY IN COOLING TOWERS....................................................................... 45 THERMAL STORAGE FOR MAXIMUM DEMAND CONTROL.......................................................... 47 4.1 4.2 5 INTRODUCTION .................................................................................................................................. 5 REFRIGERATION SYSTEM EFFICIENCY .................................................................................................. 5 VAPOUR COMPRESSION SYSTEMS ....................................................................................................... 6 Operating Principle ................................................................................................................... 6 Refrigerants: Ozone Depletion and Global Warming ................................................................ 8 Types of Compressor & Capacity Control............................................................................... 10 Evaporators ............................................................................................................................ 15 Condensers ............................................................................................................................ 17 Expansion Valves ................................................................................................................... 19 SUB-COOLING ................................................................................................................................. 20 SUPERHEATING ............................................................................................................................... 20 Secondary Coolants ............................................................................................................... 20 Specific Power Consumption of Vapour Compression Systems............................................. 21 VAPOUR ABSORPTION REFRIGERATION SYSTEM ................................................................................. 22 Operating Principle ................................................................................................................. 23 CAPACITY CONTROL ........................................................................................................................ 26 Specific Fuel Consumption Of Vapour Absorption Systems ................................................... 26 COOLING TOWERS ........................................................................................................................... 28 INTRODUCTION ................................................................................................................................ 47 TECHNOLOGIES ............................................................................................................................... 47 SYSTEM DESIGN AND EQUIPMENT SELECTION: ENERGY ISSUES ........................................... 49 5.1 INTRODUCTION ................................................................................................................................ 49 5.2 IMPORTANT ISSUES .......................................................................................................................... 49 5.2.1 Energy Cost............................................................................................................................ 49 5.2.2 Refrigeration Load Estimation................................................................................................. 49 5.2.3 System Design........................................................................................................................ 50 5.2.4 Minimise Heat Ingress – Select Right Thermal Insulation....................................................... 51 5.2.5 Sizing & Selecting the Right Refrigeration Machine................................................................ 52 5.2.6 Controls for Energy Efficiency................................................................................................. 54 2
  3. 3. 6 CASE STUDIES .................................................................................................................................. 55 6.1 6.2 6.3 6.4 6.5 6.6 6.7 6.8 6.9 6.10 CASE STUDY 1: OPERATIONAL SAVING – CORRECT REFRIGERANT CHARGING ................................... 55 CASE STUDY 2: MATCHING COMPRESSOR CAPACITY TO ACTUAL LOAD BY SPEED VARIATION ............. 56 CASE STUDY 3: REPLACEMENT OF INEFFICIENT CHILLER .................................................................... 57 CASE STUDY 4: INNOVATIVE RETROFIT PRECISION TEMPERATURE CONTROLLER .................................. 58 CASE STUDY 5: ELIMINATION OF RE-HEAT IN LOW RELATIVE HUMIDITY AIR CONDITIONING................... 59 CASE STUDY 6: LARGER HEAT EXCHANGERS IMPROVE COP ............................................................... 60 CASE STUDY 7: ELECTRONIC EXPANSION VALVES SAVE ENERGY ........................................................ 60 CASE STUDY 8: PRE-COOLING OF AUDITORIUM VENTILATION AIR........................................................ 62 CASE STUDY 9: ENERGY SAVING IN FRUIT COLD STORES ................................................................... 63 CASE STUDY 10: TRI-FUEL CHILLER OPTIONS SAVES COST ............................................................... 67 7 REFERENCES .................................................................................................................................... 68 8 CONVERSION TABLES ..................................................................................................................... 69 LIST OF FIGURES Figure 2-1: Schematic Diagram of Vapor Compression System ....................................................................................6 Figure 2-2: Pressure – Enthalpy Diagram for Vapour Compression System................................................................7 Figure 2-3: Roller Compressor..........................................................................................................................................11 Figure 2-4: Rotary Sliding Vane Compressor ....................................................................................................................11 Figure 2-5: Reciprocating Compressor.............................................................................................................................12 Figure 2-6: Recips - Power at Part Load Operation...........................................................................................................12 Figure 2-7: Screw Compressor .........................................................................................................................................13 Figure 2-8: Screw - Power at Part Loads ..........................................................................................................................13 Figure 2-9: Scroll Compressor ..........................................................................................................................................13 Figure 2-10: Centrifugal Compressor ................................................................................................................................14 Figure 2-11: Centrifugals – Power at Part Loads...............................................................................................................14 Figure 2-12: Air Handling Unit for Cooling Air....................................................................................................................15 Figure 2-13: Shell & Tube Heat Exchangers .....................................................................................................................15 Figure 2-14: Plate Heat Exchanger ...................................................................................................................................16 Figure 2-15: Grooved Tubes to Increase Surface Area ....................................................................................................17 Figure 2-16: Tube Inserts to Increase Turbulence.............................................................................................................17 Figure 2-17: Some Commonly Used Condensers .............................................................................................................18 Figure 2-18: Schematic Diagram of Superheat Sensing Expansion Valve.........................................................................19 Figure 2-19: Anti-freeze Solutions – Change in Freezing Point with Concentration ...........................................................21 Figure 2-20: Schematic Diagram of Single Effect Absorption Chiller .................................................................................24 Figure 2-21: Schematic Diagram of Double Effect Absorption Chiller................................................................................25 Figure 2-22: Schematic Diagram of Triple Effect Absorption Chiller ..................................................................................25 Figure 2-23: Counter-flow Induced Draft ...........................................................................................................................29 Figure 2-24: Cross-flow Induced Draft...............................................................................................................................29 Figure 2-25: Variation of Cooling Water Leaving Temperature with Variation in Ambient WBT........................................30 Figure 3-1: Building Structure Cooling: Grid of Pipes on the Roof and Floor .....................................................................32 Figure 3-2High Speed Door ..............................................................................................................................................35 Figure 3-3: Dock Leveler helps seal back of truck with building.........................................................................................35 Figure 3-4: Example of good thermal insulation in a chilled water system .........................................................................35 Figure 3-5: Typical Modern Building with Glass Façade....................................................................................................36 Figure 3-6: Heat Pipes ......................................................................................................................................................38 Figure 3-7: Heat Wheel.....................................................................................................................................................39 L I S T O F T AB L E S Table 2-1: Summary of Status of Some Refrigerant Groups......................................................................9 Table 3-1: Reduction in Roof Underside Temperature due to Structure Cooling ..................................32 Table 3-2: Effect of Evaporator and Condenser Temperatures on Refrigeration Machine Performance .......33 Table 3-3: Heat Ingress into Air-conditioned Space through Open Doors .....................................................35 Table 3-4: Properties of Different Types of Window Glass .......................................................................37 Table 5-1: Thumb Rules for Calculating Comfort Air-conditioning Load ................................................50 Table 5-2: Thermal Conductivities of Some Insulating Materials ...................................................................51 Table 5-3: Insulation thickness for Refrigeration Piping .................................................................................52 Table 5-4: Comparison of Likely Energy Consumption for a Typical 100 TR Air-Conditioning System.........53 3
  4. 4. 1 1.1 I N T R O D U C TI O N Refrigeration & Air-conditioning India, being a warm tropical country, most of the refrigeration and HVAC applications involve cooling of air, water, other fluids or products. Heating is used only for a very small period in winter in the northern parts of the country and in places at high altitudes. Refrigeration and Air-conditioning accounts for a significant portion of the energy consumption in many manufacturing industries (like chemicals, pharmaceuticals, dairy, food etc.), agricultural & horticultural sectors (mainly cold stores) and commercial buildings (like hotels, hospitals, offices, airports, theatres, auditoria, multiplexes, data processing centers, telecom switching exchanges etc). Refrigeration and air conditioning systems cover a wide variety of cooling applications, using both standard and custom-made equipments. Some commonly used applications are process cooling by chilled water or brine, ice plants, cold stores, freeze drying, air-conditioning systems etc. Comfort air-conditioning generally implies cooling of room air to about 24°C and relative humidity in the range of 50% to 60%. Industrial process air conditioning and precision air conditioning may require temperatures ranging from 18°C to 24°C with relative humidity values ranging from 10% to 60%. This manual highlights some issues related to energy efficiency and energy conservation in refrigeration and air conditioning, along with some emerging innovative techniques to eliminate or minimize conventional refrigeration and air conditioning. 1.2 The Need for Radical Thinking With industrial development, the demand for process related refrigeration and air conditioning is increasing. However, modern lifestyles with the rising demand for comfort air conditioning in commercial buildings and homes, using conventional air conditioning methods and equipments, are a source of concern for an energy scarce country like India. Significant developments have taken place in the technology related to the hardware and controls related to refrigeration and air conditioning systems to help improve energy efficiency. However, the right attitude and design philosophy can play a larger role than technology in conserving energy. This implies that use of nature-assisted cooling techniques and minimal use of energy guzzling refrigeration equipments is the key energy conservation. There is an urgent need to promote and commercialize all proven techniques that use natural processes to eliminate or minimize the use of conventional refrigeration and air conditioning. Basic design of industrial processes and also architectural spaces should strive to minimize the demand for conventional refrigeration and air conditioning. A strategy focusing on both refrigeration load reduction and energy efficiency improvement for conventional refrigeration is necessary to limit the unmitigated growth of conventional refrigeration. 4
  5. 5. 2 2.1 REFRIGERATION & AIR CONDITIONING SYSTEMS Introduction The most commonly used systems for industrial and commercial refrigeration and air conditioning are Vapour Compression Refrigeration System and Vapour Absorption Refrigeration System. Vapour compression machines, usually with electrically driven compressors, are the most commonly used machines for refrigeration and air conditioning for temperatures ranging from 25°C to -70°C. Vapour Absorption Refrigeration machines, wherein heat energy is consumed, are being increasingly used. Absorption refrigeration machines may be economical in situations where process waste heat or cheap fuels (usually coal or agro-waste) are available. The uncertainty of energy availability and prices is likely to increase the preference for Hybrid Systems, incorporating both Vapour Compression and Vapour Absorption. With the availability natural gas, engine driven vapour compression system or engine waste heat based vapour absorption systems may also find increasing use. 2.2 Refrigeration System Efficiency The cooling effect of refrigeration systems is generally quantified in tons of refrigeration. The unit is derived from the cooling rate available per hour from 1 ton (1 short ton = 2000 pounds = 907.18 kg) of ice, when it melts over a period of 24 hours. British measuring units are still popularly used by refrigeration and air conditioning engineers; hence it is necessary to know the energy equivalents. 1 Ton of Refrigeration (TR) = 3023 kcal/h = 3.51 kW thermal = 12000 Btu/hr The commonly used figures of merit for comparison of refrigeration systems are Coefficient of Performance (COP), Energy Efficiency Ratio (EER) and Specific Power Consumption (kW/TR). These are defined as follows: The If both refrigeration effect and work done by the compressor (or the input power) are taken in the same units (TR or kcal/hr or kW or Btu/hr), the ratio is COP = Refrigeration Effect Work done If the refrigeration effect is quantified in Btu/hr and work done is in Watts, the ratio is EER = Refrigeration Effect (Btu/hr) Work done (Watts) Higher COP or EER indicates better efficiency. 5
  6. 6. The other commonly used and easily understood figure of merit is Specific Power Consumption = Power Consumption (kW) Refrigeration effect (TR) Lower Specific Power Consumption implies better efficiency. 2.3 Vapour Compression Systems 2.3.1 Operating Principle Vapour compression systems are commercially used for both very small systems (like window air conditioners, refrigerators etc.) to very large systems (in industries and commercial buildings). Figure 2-1: Schematic Diagram of Vapor Compression System 6
  7. 7. Figure 2-2: Pressure – Enthalpy Diagram for Vapour Compression System The vapor compression system comprises the following basic steps (fig. 2.1 & 2.2): 1. Step 1-2-3: Absorption of heat by the liquid refrigerant and conversion to gas in the evaporator. Refrigerant is a substance with low boiling point at a desired working pressure. The surface of the evaporator is in contact with air, water or any other fluid or substance that it may be cooling. (From 1 to 2, liquid refrigerant absorbs latent heat energy, at constant pressure and temperature, converting itself to saturated vapour without increase in temperature; from 2 to 3, it absorbs additional heat at constant pressure to become superheated vapor with some increase in temperature. Superheating is necessary to prevent liquid refrigerant from entering the compressor). 2. Step 3-4: Compression of low temperature, low pressure refrigerant gas from the evaporator to high temperature, high pressure gas in the compressor. (From 3 to 4, reduction in vapour volume during compression, with increase in pressure; the joule equivalent of work done during compression, increases the temperature of the vapour to level higher than ambient). 3. Step 4-5-6-7: Rejection of heat to the in the condenser, resulting in condensation of the gaseous refrigerant to liquid at high pressure. The condenser surface is cooled by moving air or water. (From 4 to 5, vapour temperature drops when superheat is removed and the vapour is saturated; from 5 to 6, saturated vapour condenses back to liquid phase at constant temperature and pressure; from 6-7, the liquid is subcooled below its saturation temperature). 7
  8. 8. 4. Step 7-1: Expansion of the liquid refrigerant from high condenser pressure to low evaporator pressure through a throttling valve, called expansion device or valve. The opening of the expansion valve is controlled to enable capacity regulation. (There is no heat addition or removal during this process, but some flash gas is formed as a very small portion of the liquid refrigerant evaporates between the expansion valve and the evaporator. To reduce flash gas formation, condensers are sometimes giving more heat transfer area to sub-cool the refrigerant or a very small quantity of refrigerant is separately expanded in a sub-cooler to cool the liquid refrigerant before the expansion valve.) The heat transfer rate in the evaporator influences the refrigerant suction temperature and pressure. The ambient conditions and heat transfer rate in the condenser influence the discharge temperature and pressure. The suction and discharge pressures, that is, the compression ratio basically decides the extent of work to be done by the compressor and hence the energy consumption in the compressor. Since the compressor suction and discharge pressures are governed by the heat transfer in the evaporator and condenser, the heat transfer efficacy of these heat exchangers and the regulation of refrigerant flow through the system by the expansion valve and the performance of the compressor at partial loads plays a major role in deciding the overall operating efficiency of the vapour compression system. 2.3.2 Refrigerants: Ozone Depletion and Global Warming Refrigerants are substances with low boiling points and large latent heats, at pressures above atmospheric pressure. Refrigerants usually fall into one of the following groups: • • • • • CFCs – chlorofluorocarbons; HCHCs – hydro chlorofluorocarbons; HFCs – hydro fluorocarbons; HCs – hydrocarbons; NH3 – ammonia. CFCs deplete stratospheric ozone and, following the Montreal Protocol, are no longer produced. HCFCs also deplete ozone, but to a lesser extent, and will be phased out in Europe by 2015. Small quantities are manufactured under strict regulation for few older systems. Developing countries have been permitted more time for the transition. Hence new refrigeration systems with HCFCs are still sold in developing countries. HFCs have been developed in the 1990s to replace CFCs and HCFCs. HCs are also being used as replacements. Refrigerants consume energy during their manufacture and refrigeration plants also contribute to global warming as they consume electricity and other fuels to operate. Combustion of fuels in power stations or refrigeration equipments result in emission of carbon dioxide, which is a greenhouse gas that contributes directly to global warming. The total direct and indirect global warming impact of refrigerants is called its Total Equivalent Warming Impact (TEWI) value. 8
  9. 9. Table 2-1: Summary of Status of Some Refrigerant Groups Type Examples R12 R502 R11 R22 R409A R411B NH3 Ammonia HFC HC E.G. propane, iso-butane, iso-pentane Uses Other Issues High High Low High Zero Very low Now phased out of production To be phased out of production in 2015. Their use is also regulated increasingly strictly. Toxic and flammable, reacts with copper. Zero High Widely used in most applications until 1990. Widely used in many applications. Not recommended for us after 1999. Used in industrial systems since the birth of refrigeration. Started to be used in place of CFCs from about 1990. Zero Very low Zero HCFC GWP** R717 CFC ODP* Very low R134a R404A R407C R410C R507 R600a R290 Care 30 Care 50 R1270 CO2 R290 used in some industrial systems for decades. R600a now used in domestic systems. Care 30 and Care 50 now used in some commercial systems. Widely used before the 1950s but superseded by halocarbons. Now being ‘rediscovered’ as a primary and secondary refrigerant. Different compressor oil needed performance of some HFCs not as good as CFCs. Some reliability problems. Flammable, but are very good refrigerants with few changes needed to a CFC/HCFC system. Not yet widespread commercial use as a primary refrigerant, but an interesting prospect. (High operating pressures require special materials and construction.) *ODP – Ozone Depleting Potential; **GWP – Global Warming Potential Many of the new refrigerants are blends of different substances, which fall into two categories: • • Those with a low ODP which are used as transitional substances, these are usually blends based on HCFC R22 (e.g. R409A, R411B); Those with zero ODP, which have a longer term future, these are usually based on HFCs (e.g. R404A, R407C), or HCs (e.g. Care 30, Care 50). The transitional substances are primarily used to convert existing systems. They should not be specified for new equipment. As they include R22, they can operate with the existing (mineral) oil in the system and the conversion procedure is relatively simple. The blends based on HCFCs or HCs can be used to replace the HCFC or CFC refrigerant in existing systems without changing the oil. Blends based on HFCs are usually only used in new systems. The blends are mostly of two or three substances and are classified as Zeotropic blends or Azeotropic blends. Zeotropic Blends Zeotropic blends behave differently in a system compared to a single substance. While a single substance has a single evaporating/condensing temperature, zeotropic blends evaporate and condense across a small temperature range, and are said to have a ‘temperature glide’. The temperature glide is the difference between the ‘bubble temperature’ (when the refrigerant is saturated and about to evaporate and the ‘dew 9
  10. 10. temperature’ (when the saturated vapour is about to condense). This property may lead to increased refrigeration capacity when the refrigerant and the cooled fluid are in counter flow, may lead to uneven ice build up leading to problems in defrosting and may be difficult to use in a flooded system. If required, the refrigerant will also have to be removed as a liquid from the system to prevent change in the composition of the remaining refrigerant in the system. Azeotropic Blends Blends that do not have a temperature glide are called azeotropic blends and they behave like a single substance. e.g. R502 and R507. Hydrocarbons (HCs) HCs are inflammable and safety is a serious issue. These refrigerants are being used in domestic refrigerators. However, in India, care is required from the view point of safety because a major portion of the refrigerator repair market is in the unorganized sector. Ammonia (R717 or NH3) Anhydrous ammonia is popularly used as a refrigerant in industrial systems, especially chemical and dairy industries. Ammonia has high latent heat and hence less mass flow is required, resulting in slight reduction in the power consumption. Lubricating oil, being denser than ammonia, can be easily drained from the lower points of the system. Air, being heavier than ammonia, can be purged easily from the highest point in the system. All these properties contribute to the design of ammonia systems that are slightly more efficient operationally. Ammonia is toxic in high concentrations. The occupational exposure limit is 25 ppm when the smell is quite obvious. Most people can tolerate up to about 250 ppm, with some irritation and discomfort. At 3500 ppm, ammonia is quite lethal. A 16% to 27% ammonia-air mixture can be ignited with some difficulty. Ammonia also attacks copper, zinc, tin, calcium and their alloys. • • Relative performance of a refrigerant is affected by the type of compressor and the operating conditions. • Zeotropic blends can give advantage in capacity and efficiency when used correctly i.e. advantage is taken of the temperature glide in the evaporator. • Too much or too little charge of refrigerant can reduce efficiency. • Insufficient refrigerant reduces the wetted area in the evaporator, increases the superheat, reduces the suction pressure, increases the temperature lift and reduces the efficiency. • 2.3.3 The refrigerant type can affect the efficiency of the system by about 10%. Refrigerant, contaminated with air or other gases, will affect the efficiency of the system. Types of Compressor & Capacity Control The commonly used compressors for most vapour compression systems are reciprocating, screw, scroll and centrifugal. For very small applications like window air 10
  11. 11. conditioners and split air conditioners, small rotary roller or sliding vane or reciprocating compressors are used. The compressors are constructed as Open, Hermetically Sealed and Semi-Hermetic (semi-bolted) compressors. In the open type compressor, the shaft extends out of the compressor and is connected externally to the prime mover (electric motor or engine). In the hermetically sealed motor-compressor unit, the entire assembly is encapsulated, only the refrigerant lines and electrical connections extend out of the housing. In semihermetic compressors, while the motor and compressor are encapsulated, the heads of the compressors can be removed to gain access to the pistons and valves for servicing. The motor is also accessible for repair by removing the bolted plate. In both hermetic and semi-hermetic compressors, the refrigerant is in contact with the motor windings. So only halocarbon refrigerants, which do not attack copper, can only be used; ammonia cannot be used. Presently, ammonia compressors are always of the open type. Open type compressors are usually more efficient than the hermetic and semi-hermetic types because the suction vapour in a hermetic compressor passes over the motor to cool it, resulting in super heating of the vapour and thereby requiring more power for compression. However, proper refrigeration system design can minimize the impact on energy consumption. The rotary compressors are usually suitable for small, fraction tonnage capacity machines like window air-conditioners. These compressors are roller, vane or reciprocating type. In the roller type compressor (fig. 2.3), the roller is eccentrically mounted in a cylindrical space having spring loaded separator. The low pressure vapour enters, gets compressed and finally discharged to the condenser. Roller type compressors are manufactured up to 5 ton capacity. In the vane type compressor (fig. 2.4), a number of vanes are mounted in the slots of an eccentrically mounted rotor. The position of vanes changes as the rotor rotates. The compression ratio is limited to about 7:1. The capacity control is by cycling the compressor on and off. Exit Inlet Figure 2-3: Roller Compressor Figure 2-4: Rotary Sliding Vane Compressor 11
  12. 12. Figure 2-5: Reciprocating Compressor Figure 2-6: Recips - Power at Part Load Operation In a reciprocating compressor, the refrigerant vapour is compressed by movement of the piston in a cylinder (fig. 2.5). Reciprocating compressors are commonly used up to single machine capacities of 250 TR. In the case of small machines, the arrangement may be cyclic on/off control based on temperature sensing. However, in larger machines, as frequent starts and stops of motors are not permitted, other methods of capacity control are adopted. In reciprocating compressors with multiple cylinders, cylinders are selectively loaded or unloaded, based on set pressures (reflecting the temperatures); the variation in power with cylinder unloading is shown in fig. 2.6. Unloading implies that the suction valve is kept open so that the vapour, taken in during the suction stroke, returns back through the suction valves itself during the discharge stroke. Reciprocating compressors cannot tolerate liquid slugging, which can happen when the evaporator load is less and the superheat controlled expansion valve is unable to regulate the flow of refrigerant correctly, resulting in excess liquid refrigerant entering the evaporator and getting sucked into the compressor. Liquid slugging can cause serious damage to the compressor. In a screw compressor (fig.2.7), there is male rotor with lobes and female rotor with gullies. As both the rotors rotate in opposite directions, the gas gets drawn in, gets sealed between the rotors and the housing, gets compressed as the cavity bears against the end of the housing and, finally, as the screw thread reaches the discharge port, the compressed gas flows into the discharge line. The compression ratio in a single stage can go up to 25:1, which is significantly higher than the pressure ratios of reciprocating compressors. Screw compressors are available for refrigeration capacities from about 10 TR to 1200 TR, but commonly used in the 100 to 300 TR range. For capacity control, sliding valve control is used to bypass some gas back to the suction (depending on the position of the sliding valve) and hence reduce the volumetric efficiency of the compressor. The variation in power consumption and cooling capacity for a screw compressor is shown in fig. 2.8. Due to internal losses, capacity control by sliding valve below 60% capacity is not very efficient. However, screw compressors can tolerate liquid slugging. 12
  13. 13. Figure 2-7: Screw Compressor Figure 2-8: Screw - Power at Part Loads Figure 2-9: Scroll Compressor In the Scroll compressor (fig. 2.9), the main components are two involute scrolls that intermesh. The top scroll, which contains the gas discharge port, is fixed and the bottom scroll orbits. The two scrolls are maintained with a fixed annular phase relation (180°) by an anti-rotation device. As the bottom scroll orbits within the other, crescent shape gas pockets are formed, their volumes are reduced until they vanish at the centre of the 13
  14. 14. scroll. Suction, compression and discharge are simultaneously performed in a continuous sequence by the orbiting motion of the scroll. Scroll compressors are available for capacities up to 30 TR; multiple compressors are used to build larger packages. The capacity control of Scroll compressors is by cyclic on/ off control. Some new Scroll designs have the facility to operate at 100% and 67%. Scroll compressors can tolerate some liquid slugging and particulate contamination. Scrolls can tolerate high discharge temperatures and pressures. Figure 2-10: Centrifugal Compressor Figure 2-11: Centrifugals – Power at Part Loads In the Centrifugal compressor (fig 2.10), large volumes of vapour are centrifugally accelerated to high velocity and this velocity energy is converted to pressure. The compression ratio is around 5:1 at 3600 rpm. The speed of the centrifugal compressor goes very high at around 20,000 rpm. These machines are manufactured in the range of 35 to 10,000 ton capacity. Centrifugals are generally used beyond 150 ton single machine capacity. In centrifugal compressors, capacity control is ususally by inlet guide vanes at the suction. Capacity control in the range of 10% to 100% is possible; the variation of power with capacity is shown in fig. 2.11. The partial load operation of all compressors is inefficient compared to full load operation as the power does not drop in proportion to the drop in capacity. Capacity control for all types of compressors can be done very efficiently by varying the speed of the compressor. The permitted range of speed variation will vary depending on the compressor type and the lubrication arrangement. • The efficiencies of compressors of different types and makes may be different. So accurate comparisons are required at the time of selection. Compressor efficiency at part loads is key issue to be considered. • It is desirable to avoid the use of single large compressor where the refrigeration load is variable. Multiple smaller machines operating close to full load are more desirable. • Compressors with variable speed drives always result in better efficiency at part loads. 14
  15. 15. Evaporators 2.3.4 The evaporator is the heat exchanger where the heat is removed from the system by the boiling of the refrigerant in the evaporator. The heat may be removed from air, water or any other process coolant. The evaporator may be refrigerant cooled coils in an air stream (Air Handling Unit – AHU) (fig. 2.12) for air conditioning, shell and tube heat exchangers (fig. 2.13) with refrigerant in the tube or shell sides, plate heat exchangers (fig. 2.14) or refrigerant coils submerged in water or brine tanks. Refrigerant Air Figure 2-12: Air Handling Unit for Cooling Air Warm Liquid Refrigerant Vapor Baffles Refrigerant Vapor Warm Liquid Cool Liquid Liquid Refrigerant Cool Liquid Refrigerant Liquid Cool Liquid Figure 2-13: Shell & Tube Heat Exchangers 15
  16. 16. Figure 2-14: Plate Heat Exchanger The coils are generally of two types: (a) Direct Expansion (DX) type, wherein regulated quantity of refrigerant liquid is allowed to enter through the expansion valve and the vapour get sucked by the compressor or (b) Flooded type, wherein the entire shell or large coil is flooded with refrigerant liquid by gravity from a surge drum or by pumping, the vapour from the boiling liquid move back into the surge drum and then get sucked by the compressor. The surge drum gets liquid refrigerant from a liquid receiver due to pressure difference. In flooded evaporators, the entire heat transfer surface is wetted with liquid refrigerant. Flooded evaporators tend to accumulate lubricating oil and suitable arrangements are provided to drain the oil. Evaporators are designed to with parallel tubes to maximize heat transfer area, minimize pressure drop and also ensure adequate refrigerant velocity to facilitate return of lubricating oil back to the compressor. Formation of oil film on heat transfer surfaces can significantly reduce the heat transfer rate. Baudelot cooler is used when water is required very close to freezing temperature, say Baudelot cooler, which comprises vertical tubes or plates, with water tricking down in film form on one side and boiling refrigerant on the other side. The water collects in a tank below. The heat transfer in the evaporator depends on the surface area, the fluids involved, the turbulence in the fluid streams and the operating temperature and pressure. The heat transfer 2 coefficients may range from 1500 to 5000 W/m °K, depending on the evaporator design and refrigerants used. The benefits of Plate Heat Exchangers (PHEs) over conventional shell and tube heat exchangers are smaller refrigerant volumes (5 to 20%) due to low internal holding volume, easy access for maintenance and inspection, easy augmentation of heat transfer area by addition of plates, high heat transfer coefficients resulting from the intense turbulence in the plate channels and reduced fouling tendencies and higher reliability. PHEs can be designed to have closer approach temperatures i.e. higher evaporating temperature (for same end-use temperature) to achieve higher COP. PHEs have been in use for secondary heat transfer to products (especially in food and pharmaceutical industries) for a long time. More recently, PHEs have been also used as evaporators and condensers in refrigeration systems in place of shell and tube heat exchangers. 16
  17. 17. Figure 2-15: Grooved Tubes to Increase Surface Area Figure 2-16: Tube Inserts to Increase Turbulence Larger heat transfer area in the evaporator leads to better heat transfer from the process coolant to the refrigerant, resulting in higher refrigerant temperature and pressure and less energy consumption. Heat transfer area can be increased in heat exchangers by providing more tubes or larger number of smaller tubes or by surface area enhancement techniques like use of grooved tubes (fig.2.15), finned tubes, helical wire inserts in tubes (fig.2.16) etc. Within certain limits, the coefficient of heat transfer can be increased by operation at higher process coolant velocities. Trade offs have to be made depending on pressure drops, energy cost and material cost. 2.3.5 Condensers The condenser is the heat exchanger where the refrigerant gas condenses, giving up its heat to the atmosphere. The condensers may be natural air draft cooled for small equipment like refrigerators, forced air draft cooled condensers, water cooled shell and tube condensers or water cooled plate heat exchangers or evaporative condensers. Some of the commonly use condensers are shown in fig. 2.17. In the case of water-cooled condensers, the water is generally cooled in cooling towers or spray ponds. In some cases, evaporative condensers are used where water is sprayed on coils; the heat is directly dissipated to the atmosphere, avoiding the need for a separate cooling tower or spray pond. 2 The heat transfer coefficients range from 1400 to 11000 W/m °K, depending on the condenser design and refrigerant used. The issues relating to various types of heat exchangers in section 2.2.4 are also relevant to condensers. Most refrigerants have low surface tension, which promotes the formation of a thin condensate film on the external profile of the tube. Heat transfer is an inverse function of condensate film thickness and therefore increases with thin condensate films. Hence, short, vertical fins on a horizontal tube will gave a smaller film thickness than on plain tube. 17
  18. 18. Figure 2-17: Some Commonly Used Condensers Integral externally finned tubes, additional longitudinal or spiral grooves and ridges in finned tubes etc. create turbulence and augment water side heat transfer. These features promote turbulence and may also help retard the adverse effect of fouling. However, finned tubes may retain condensate, restricting its performance. Several enhanced surfaces with complex surface geometries have been developed to promote surface tension-drained condensation. Air cooled condensers, being limited by the dry bulb temperature of air, generally result in higher refrigerant condensing temperature and pressure, compared to water cooled condensers, leading to higher compression ratios and higher power consumption (about 20% or higher) in compressors. However, water scarcity and absence of water treatment facilities is forcing many users to prefer air cooled condensers. In such cases, providing evaporative cooling pads before the condenser can help reduce the condensing temperature and pressure when the weather is dry i.e. low relative humidity conditions. Air cooled condensers facilitate the use of warm air for space heating in during cold weather. • • Condenser performance improves when the coolant (air or water) temperature is low. Evaporative condensers are more efficient than shell and tube condensers. However, these are difficult to repair in case of tube puncture. Evaporative condensers are also more prone to corrosion due to the constant presence of air around the tubes. 18
  19. 19. • The overall heat transfer coefficient of a heat exchanger is determined by the designer and the application engineer has no control over it. • For the same duty conditions, the heat exchanger with more primary tube surface area will have higher efficacy, all other parameters being equal. 2.3.6 Expansion Valves The expansion device is a refrigerant flow control device that helps match the refrigerant flow rate with the boil off rate in the evaporator, in the process reducing the pressure of the refrigerant from the high condensing pressure to the low evaporator pressure. To utilize the coil more effectively, liquid refrigerant should be present right up to the end of the coil, instead of getting superheated over some area toward the end section of the coil. However, superheat section is a trade-off, to protect the compressor from the possibility of liquid entry to the compressor. The high pressure, liquid refrigerant is passed through the expansion device into the evaporator, where the refrigerant vaporizes, due to the heat from the process coolant or material being cooled. The expansion device may be a fixed orifice or capillary tube, manually controlled valve, thermostatic, electronic or balanced port valve, float valve or superheat controlled expansion valve. Superheated Refrigerant Evaporator Liquid Refrigerant Figure 2-18: Schematic Diagram of Superheat Sensing Expansion Valve Orifice plates and capillary tubes are used only for small machines like window air conditioners, refrigerators etc. where the capacity control is by cycling the compressor on and off and no refrigerant flow control is required. Thermostatic valves have an orifice to provide a pressure drop and a needle valve and diaphragm to regulate the flow of refrigerant based on the evaporator outlet refrigerant vapour temperature, which is kept about 5ºK above the evaporating temperature, to prevent liquid entering the compressor. Balanced port valves are similar to thermostatic valves, apart from a special internal balanced port design, which enable better flow control. Electronic valves are also similar to thermostatic valves with the difference that the temperature is sensed electronically and the orifice opening is changed either by heated fluid pressure or by electrically actuated valve. Electronic valves can be easily integrated into an electronic microprocessor based control system. 19
  20. 20. The superheat sensing valve (fig. 2.18) is the most commonly used refrigerant flow control device. This valve controls the refrigerant superheat leaving the evaporator. The valve stem is positioned by the pressure difference on opposite sides of the diaphragm. The pressure under the diaphragm is provided by the refrigerant at the inlet to the evaporator and the pressure on the top of the diaphragm by a power fluid, which is the same refrigerant used in the system. A slight force exerted by the spring on the valve stem keeps the valve closed until the pressure above the diaphragm overcomes the combined forces of the spring and the evaporator pressure. For the pressure above the diaphragm to be higher than the evaporator pressure below the diaphragm, the power fluid temperature must be higher than the saturation temperature in the evaporator. The refrigerant gas at the outlet of the evaporator, therefore, must be superheated to bring the power fluid up to the valve opening pressure. The operation of the superheat controlled expansion valve can be sluggish at partial loads i.e. when the compression ratio is low. The electronic expansion valve, which can work on very low superheat settings allows more coil length to be used for liquid refrigerant, compared to a conventional expansion valve, and thus improves coil performance. A novel expansion valve controller has been developed in India to sense the process coolant (air, water, brine etc.) temperature and heat or cool the sensing bulb faster to make the operation of the superheat sensing expansion valve more sensitive at partial loads. Use of these devices has led to better temperature stability and energy savings. Float valves are used in flooded systems where the liquid refrigerant level in the surge drum is sensed and maintained. Alternatively, manually adjusted valves with a level switch are also provided for flooded evaporators. 2.4 Sub-cooling Sub-cooling of the liquid refrigerant before the expansion valve reduces the flash gas formation and helps increase the evaporator capacity. Sub-cooling can be provided by providing more heat transfer area in the condenser or providing a compressor suction gas to refrigerant liquid heat exchanger or flashing of minuscule quantity of liquid refrigerant to cool the liquid refrigerant. In the case of flooded evaporators, location of the receiver in a cool location can help achieve some free sub-cooling. The COP can improve by 5% to 10% by sub-cooling. 2.5 Superheating Superheat is the increase in temperature of refrigerant gas above the evaporating temperature. The higher the suction gas superheat, lower the gas density and therefore, lower the compressor mass flow rate. This reduces the compressor capacity without reducing its power consumption, increasing running costs. Superheat may be picked up while doing useful cooling or in the suction piping from the evaporator to the compressor. To some extent, superheat, is a necessary evil to prevent liquid refrigerant from entering the compressor. The advent of electronic expansion valves has helped minimize superheat without the danger of liquid slugging. Suction lines should always be insulated to minimize superheat. 2.5.1 Secondary Coolants In air conditioning air may be directly cooled in the heat exchanger (air handling unit) or through a secondary coolant. In most industrial applications, the final material to be cooled is generally cooled through an intermediate process coolant like water or water with an antifreeze agent (generally termed as brines). The concentration of the anti-freeze agent affects 20
  21. 21. the freezing point and also the heat transfer rate. Fig 2.19 shows the variation of freezing points with the concentration of the anti-freeze agents of some commonly used anti-freeze solutions. Figure 2-19: Anti-freeze Solutions – Change in Freezing Point with Concentration 2.5.2 Specific Power Consumption of Vapour Compression Systems The efficiency of refrigeration systems depends on the operating temperature and hence all figures of merit related to efficiency have to specified at a certain operating temperature. Well designed, well maintained, water cooled vapour compression systems, using reciprocating, screw or scroll compressors, for chilled water at 6°C to 8°C have COP of 4 to 5.8, EER in the range of 14 to 20 Btu/hr/W or Specific Power Consumption in the range of 0.61 to 0.87 kW/TR. Open-type compressors are more efficient than semi-hermetic compressors; in semihermetic compressors, the motor is also cooled by the refrigerant. Centrifugal compressors, which are generally used for cooling loads about 150 TR, can have COP of about 6, EER greater than 20 and Specific Power Consumption of 0.59 kW/TR. The COP of systems with air cooled condensers is generally about 20% to 40% higher. In areas with dry weather, the COP improves significantly, if evaporatively cooled saturated air is provided (using cooling pad and booster fan) instead of ambient dry air. The COP of well designed small machines like window air conditioners and split air conditioning units are generally in the vicinity of 2.5. The COP is poor due the compactness of the machine, which limits heat transfer area, and the fact that the condenser is air cooled. 21
  22. 22. It may be noted that COP is calculated taking into account only the compressor power consumption. The power consumption of other parasitic loads like pumps, fans etc. are not considered. COP is affected by the evaporator temperature and the condenser temperature. Higher the evaporator temperature and lower the condenser temperature, better is the COP. 1ºC higher temperature of refrigerant in the evaporator or 1ºC lower in the condenser improves the COP by 2% to 4%. The evaporator temperature can be increased by: • Changing process temperature settings. • Installing an evaporator of higher rating i.e. more heat transfer area. • Keeping the heat transfer surface clean i.e. avoiding fouling, defrosting as per requirement etc. The condenser temperature can be decrease by: • Installing a condenser of higher rating i.e. more heat transfer area. • The condenser temperature is allowed to float down with ambient temperature • Water cooled or evaporatively cooled condensers are used instead of air cooled condensers COP is also affected by: • The efficiency of the type of compressor used. • The amount of refrigerant charged in the system. refrigerant leaks consume more power. • The physical properties of refrigerant used. Systems with COSP (Coefficient of System Performance) is another parameter, which has been evolved to estimate the system performance by also including the power consumption of parasitic loads like fans, pumps etc.. This is a good parameter to bench mark the overall system efficiency at a particular site but it does facilitate comparison with other similar installations as system configurations vary from site to site. 2.6 Vapour Absorption Refrigeration System The Vapour Absorption Systems or Absorption Chillers use heat source to produce cooling effect. There is no compression of refrigerant vapour in this system. Absorption chillers are used in locations with access to cheap heat energy source or process waste 22
  23. 23. heat. Absorption chillers have few moving parts, which means less noise and vibrations, an important issue in commercial buildings. Vapour absorption process requires two substances with strong chemical affinity at low temperatures. The commercially available absorption chillers use the following combinations: a) Lithium Bromide (absorbent) and water (refrigerant) for chilled water at 5ºC and above. Newer versions provide slightly lower temperatures. b) Water (absorbent) and Ammonia (refrigerant) for temperatures below 5ºC. A secondary coolant (brine) is required to transfer heat to ammonia. Absorption Chillers may be single effect or multiple effect machines; the COP of multiple effect machines is higher. In India, single effect and double effect machines are being manufactured. Triple effect absorption machines are available from international manufacturers. Most of the absorption chillers in use in India are for chilled water using LiBr and water. Single machine capacities in excess of 1200 TR are available. Both steam heated and direct fired models are being widely used. A small number of chillers, using ammonia and water, are also in operation. Ammonia-water absorption chillers are single effect machines, hence their COP is poor. 2.6.1 Operating Principle Single-Effect Chiller Fig. 2.20 shows a Single Effect Chiller. The evaporator contains a bundle of tubes that carry the system water to be cooled/chilled. This is the part of the chiller where cooling of the system's water occurs. The cooling cycle begins when high-pressure liquid refrigerant from the condenser passes through an orifice into the lower-pressure evaporator, and collects in the evaporator pan or sump. This step of the cycle causes "flashing" of some of the refrigerant at the entrance to the evaporator and cools the remaining refrigerant liquid that is sprayed over the tubes carrying the system water. Transfer of heat from the comparatively warm system water to the cooled refrigerant causes the latter to evaporate and cool the water in the chiller tubes. The refrigerant vapors, generated in the evaporator, migrate to the lower-pressure absorber, where the vapors are absorbed by the lithium-bromide absorbent solution spayed over the absorber tube bundle. The absorber and evaporator share the same vapor space, allowing refrigerant vapors generated in the evaporator to migrate continuously to the absorber. The absorption process creates a lower pressure, drawing a continuous flow of refrigerant vapor from the evaporator to the absorber. In addition, the absorption process condenses the refrigerant vapors and releases the heat removed from the evaporator by the refrigerant. The heat released from the condensation of refrigerant vapors and their absorption in the solution is removed from the absorber by transferring it to the cooling coil, installed in the absorber, through which cooling tower water is circulated. The cooling tower water releases the heat removed from the absorber to the cooling tower installed at the facility. The diluted lithium-bromide solution form the absorber is pumped continuously from the absorber to the generator, which operates at a higher pressure. In the generator, heat (from natural gas, steam, or hot water) is added to boil off the refrigerant vapors absorbed in the absorber. The concentrated lithium-bromide solution produced in the generator is returned to the absorber. 23
  24. 24. Figure 2-20: Schematic Diagram of Single Effect Absorption Chiller The refrigerant vapors created in the generator migrate to the cooler condenser. The cooling tower water circulating through the condenser turns the refrigerant vapors to a liquid state and picks up the heat of condensation, which it rejects to the cooling tower. The liquid refrigerant returns to the evaporator and completes the cycle. A heat exchanger is used to recover some of heat from the concentrated hot lithiumbromide solution going from the generator to the absorber to heat the dilute cold lithiumbromide solution going from the absorber to the generator. Multiple-Effect Chiller Double Effect Chiller A double-effect chiller (fig. 2.21) is very similar to the single-effect chiller, except that it contains an additional generator, condenser, and heat exchanger that operate at higher temperatures than those for a single-effect chiller. The higher temperature generator is called the first stage generator, the higher temperature condenser is called the first stage condenser, and the higher temperature heat exchanger is called the high-temperature heat exchanger. 24
  25. 25. Figure 2-21: Schematic Diagram of Double Effect Absorption Chiller The refrigerant vapors from the first-stage generator are condensed in the first stage condenser. The heat recovered from condensation in this condenser is used to boil off additional refrigerant vapors from the lower-temperature second stage generator. This additional refrigerant vapor generated increases the capacity of the evaporator for the same heat input, resulting in increased performance efficiency. The high-temperature heat exchanger is used for recovering heat from the concentrated lithium-bromide solution from the first-stage generator to heat the lithium-bromide solution form the second-stage generator. Triple Effect Chiller A recent development is the direct fired Triple Effect Absorption Chiller (fig. 2.22) wherein the one more middle level generator and condenser are added. This chiller is now available commercially from some international refrigeration majors. Figure 2-22: Schematic Diagram of Triple Effect Absorption Chiller 25
  26. 26. Lithium Bromide – Water Absorption Chiller The LiBr-Water absorption system is commonly used for chilled water applications at 5ºC and above. Single effect absorption chillers can operate with hot water at 85ºC to 90ºC 2 or low pressure steam at pressures up to 3 kg/cm g. Double effect chillers require a 2 temperature of at least 140ºC or above, which is available from steam at 7 to 9 kg/cm g or pressurized hot water at about 160ºC or direct fuel firing. The evaporator-absorber is at a pressure of 6 mmHg and temperature of about 4ºC. The generator is at about 160ºC at full load; it reduces as part loads. The condensation of water in the condensergenerator takes place at a pressure of 75 mmHg and temperature of about 45ºC. Water – Ammonia Absorption Chiller Water – ammonia absorption single effect chillers can be used for applications requiring temperatures in the range of -40ºC to +5ºC. The preferred heat source temperature is 95ºC to 180ºC. Normal cooling water is used for cooling the absorber and condenser. For temperatures below -40ºC up to -60ºC, the cooling will have to be provided by chilled water at 10ºC to 15ºC. These chillers operate at moderate pressures and no vacuum is required till -30ºC. Other Issues Absorption chillers require vacuum pumps only for short duration while starting the machine; after that, equilibrium condition is maintained by physical and chemical phenomena. Crystallisation of LiBr in the chiller was a problem earlier. But now improved controls have overcome this problem. The problem of tube failures due to Li Br corrosion has also been over come by the use of corrosion inhibitors and providing adequate allowance in selection of tube material and thickness. 2.7 Capacity Control Capacity control is achieved by controlling the heat input rate chiller i.e. controlling the steam flow, fuel firing rate etc. This can be achieved by steam flow control or burner modulation. Absorption chillers can be turned down typically to about 25% capacity. 2.7.1 Specific Fuel Consumption Of Vapour Absorption Systems Lithium Bromide – Water Absorption Chillers Single Effect Absorption chillers at about 8°C have COP of about 0.5 to 0.6, EER is about 2.1 and Specific Steam Consumption is about 8.75 kg/hr/TR, at a steam pressure of 3 bar or lower. Double Effect Absorption chillers at about 8°C have COP in the range of 1 to 1.2, EER in the range of 3.5 to 4 Btu/hr/W and Specific Steam Consumption in the range of 4.5 to 5.25 kg/hr/TR, at a steam pressure of 8 to 8.5 bar. In the case of directly fired double effect absorption chillers, the Specific Fuel Consumption is likely to be about 0.35 3 m /hr/TR of natural gas or about 0.30 kg/h/TR of fuel oil. Triple Effect Absorption chillers are now available from international refrigeration companies and the reported COP is 1.6 i.e. EER of over 5. The steam consumption is likely to be about 2.3 kg/hr/TR. 26
  27. 27. Water – Ammonia Absorption Chillers Single Effect Absorption chillers at about -10°C have COP of about 0.55, EER is about 1.9 and Specific Steam Consumption is about 10.2 kg/hr/TR, at a steam pressure of 3 bar. At -40°C, the COP drops to about 0.45. The COP of absorption chillers improves when the evaporator is operated at higher temperature. The COP of the chiller being poor implies that the load dumped on the condenser is very large. It should also be noted that the cooling water passes through both the absorber and condenser. Hence any deficiency in the cooling water system can affect the cooling capacity and the COP of the machine. The electrical power consumption of the vapor absorption machine is only about 2% of a comparable vapor compression machine, excluding the power consumption of cooling water system. . It may also be noted that for the same heat load, the heat rejected in an absorption machine is about 60% more than in a vapor compression machine; hence the cooling water pumping power consumption is likely to be significantly higher. It may be noted that electricity savings are large; however, the economics would depend on the cost of heat energy used in the absorption system. To improve the part load efficiency of absorption chillers, variable speed drive can be used for controlling the speed of the dilute LiBr solution pump; this prevents the unnecessary sensible heating of surplus solution in the generator during low refrigeration loads. Lithium bromide will be supplied with inhibitors to limit corrosion, but regular checks (say once in a year) of chemical composition of the solution is advisable. Slow corrosion by inhibited lithium bromide will produce non-condensable gases, which will cause a very gradual loss of vacuum. If vacuum degrades more quickly than that expected from manufacturer’s guidelines, this may be an early warning of corrosion. The chilled water and condenser water circuits should also be protected against corrosion and scaling by using conventional water treatment. 27
  28. 28. Vapor compression system with water cooled condensers, using any reciprocating, screw or scroll compressors, can be designed to achieve COP of 5.5 at full load operation. The differences in compressor efficiencies are marginal at full load and can be compensated by system design. Centrifugal compressors with good system design can reach COP of 6.2 or higher. Well design vapour compression systems with air cooled condensers are likely to consume about 20% more energy. The performance can be improved by providing evaporatively cooled air to condenser. The COP of well designed small machines like window air conditioners and split air conditioning units are generally in the vicinity of 2.5. The conditions and performance of the evaporator and the condenser decide the energy efficiency of the system to a great extent. Hence one refrigeration chiller package can be compared with another, but comparison of COPs merely based on compressor types can be misleading. The COP of vapour compression systems at part loads is generally lower than that at full load. The extent of drop in COP will depend on the type of capacity control used. If capacity control is achieved by Variable Speed Drives, the COP improves and is generally higher than the full load value. While selecting or modifying a vapour compression system, the average COP (or kW/TR) of the system should be evaluated, keeping in view, the likely average loading on the plant and the anticipated COP (or kW/TR) at different loading levels. Vapour absorption chillers have low COP but are economical when operated with waste heat or cheap fuels. 2.8 Cooling Towers Cooling Towers are an integral part of water cooled refrigeration systems. Poor performance of cooling towers can lead to serious inefficiencies in plant processes and equipment, leading to higher energy consumption, higher vent losses etc. Usually, Induced Draft type, Forced Draft type or Natural Draft type towers are used in the industry. The fans used are usually axial flow fans. Induced and forced draft cooling towers operate by inducing or forcing air to flow through a matrix that is wetted by water from the condenser. Natural draft cooling towers spray water through nozzles from a height, resulting in cooling of water by the natural upward movement of air. 28
  29. 29. Figure 2-23: Counter-flow Induced Draft Figure 2-24: Cross-flow Induced Draft Two parameters, which are useful for determining the performance of cooling towers, are the Temperature Range (difference between the cooling tower inlet and outlet water temperatures) and Temperature Approach (difference between the cooling tower cold water temperature and the ambient wet bulb temperature). Though both parameters should be monitored, the Approach is a better indicator of cooling tower performance; lower the approach, better is the performance. For the same heat load, water flow and fill material, lower the Approach, larger will be size of the cooling tower and higher would be air flow requirement. Cooling towers are designed for dissipating a specified heat load at a specified ambient wet bulb temperature. However, actual wet bulb temperatures are continuously varying. Fig 2.25 shows information on variation in Temperature Approach for a particular cooling tower when it is subject to constant flow and heat load under varying ambient wet bulb temperatures. It may be noted that at lower ambient wet bulb temperatures, with constant heat load and water flow rate, the approach rises but the actual cold water temperature goes lower than the specified design value. The actual water flow rates and heat loads through the towers are also usually very different from the rated design flow rate and heat load. As site tests are difficult, at least it may be ensured that the water flow to airflow is within an acceptable range. For example, for cooling towers designed for wet bulb temperatures of 26°C and an approach of 3°C, the air flow to water flow ratio is approximately 100 cfm/USGPM (1 US GPM = 3.785 lpm), which is equivalent an Liquid to Gas ratio (L/G) of 1.16. The performance of induced draft cooling towers would depend on the condition of the fill, the heat load, the water flow, the airflow and the ambient wet bulb. The fill materials generally used are lumber, PVC honeycomb fill, PVC slats or PVC ‘V’ bars. 29
  30. 30. Leaving Water Temperature, ºF Leaving Water Temperature, ºC Ambient Wet Bulb Temperature, ºF Ambient Wet Bulb Temperature, ºC Figure 2-25: Variation of Cooling Water Leaving Temperature with Variation in Ambient WBT For every 1kW (i.e. 860 kcal/h) of heat rejected, approximately 1.5 litres of water will be evaporated. Water quality if of paramount importance. It should not be turbid or contain suspended impurities. The pH value must be between 6.5 and 7.5 to prevent salt deposition when alkaline or corrosion when acidic. The total permanent (CaCO3) hardness should be below 120 ppm to prevent scale buildup on condenser tubes, resulting in poor heat transfer and higher power consumption in compressor. Since water, available at most places in India, has impurities and high hardness level, the make-up water has to be filtered and softened. 30
  31. 31. 3 3.1 STRATEGIES AND OPPORTUNITIES FOR ENERGY SAVING Minimising Refrigeration & Air-conditioning Use Cooling Tower Water at Higher Flows for Process Cooling For process applications, the possibility of replacing chilled water with cooling water at higher flows and increased heat transfer area is a possibility for some process cooling applications. This approach can also help in replacing sub-zero brine with chilled water in some applications. Technology imported from colder countries generally specifies chilled water for cooling applications as temperatures between 10°C to 20°C are usually available from cooling towers for most part of the year in these countries. At the time of technology transfer or equipment purchase, redesign of the heat exchangers for summer cooling water temperatures, prevalent in India, or highest permissible chilled water temperatures should be seriously explored. Use Evaporative Cooling for Comfort Cooling in Dry Areas In areas having dry summer, reasonable comfort temperatures can be achieved by use of evaporative cooling i.e. by humidification of air by small desert coolers or central humidification plants. The energy consumption is likely to be about only about 10% to 20% of a conventional air conditioning system with HVAC chillers. Building Structure Cooling A significant portion of the air conditioning load is due the heat transmitted through the walls and heat stored in the structure. This results in the room inner wall surface being at temperatures higher than that of the human body. This results in discomfort as the human body is unable to radiate heat to the walls; hence heat transfer (body cooling) is possible only by convection (air movement) and perspiration. Cooling of the building structure (walls and roof) can lead to dramatic reduction in the wall temperature and human comfort. Building structure cooling helps neutralize this solar heat load by cooling the structure itself. The Central Building Research Institute, Roorkee, has developed evaporative roof cooling methods (using wetted mats on roof tops) to neutralize the heat load. Wetted mats can be spread on the roof, the water will evaporate, effectively neutralising the solar heat load. The mats can be kept wet by small pump which is controlled by a moisture sensor or timer. It may be noted that the mat should be only moist and not flooded with water. This system can very effectively eliminate or significantly reduce energy consumption air-conditioning plants. A Mumbai based company, specializing in innovations in refrigeration and air conditioning, has extended this concept further and attempted cooling the roof and the floor by burying a grid of water filled pipes (fig. 3.1), under vacuum, in the roof and floor. Water evaporates at 25ºC and the grid is connected to a small cooling tower, which acts as the heat sink and condenses the water vapour. This concept was first attempted in a pent house at Ahmedabad. In May, with Ahmedabad ambient temperature at 41.6°C, the terrace floor temperature was 61.9°C, but the structure cooling system ensured that the room temperature was only 27°C. In fact, observations reveal that the room temperature remained almost constant through out the day and night. 31
  32. 32. Figure 3-1: Building Structure Cooling: Grid of Pipes on the Roof and Floor (picture before application of cement plaster) At Jaipur, the comparison of a house with structure cooling system and a neighbouring conventional house without structure cooling is shown in table 3.1. It may be noted that the roof underside temperature with structure cooling is 29.3ºC compared to 45.2ºC without structure cooling. With structure cooling the cooled part of the building becomes a heat sink for the entire structure. A cooler structure helps more efficient heat transfer from the human body to the structure and increase the comfort level. This concept has also been implemented by a leading pharmaceutical company in Madya Pradesh for ware house cooling. This can help eliminate or reduce the need for air conditioning. Table 3-1: Reduction in Roof Underside Temperature due to Structure Cooling Roof Temperature (ºC) Difference Top side Under side 25.3 House with Roof Cooling 54.6 29.3 7.6 Neighbouring house without roof cooling 52.8 45.2 Note: Reduction in roof heating load is 75% for air conditioning at 24ºC Building structure cooling potential has to be aggressively exploited with innovative methods to eliminate or minimize the need for air conditioning. 3.2 Operating at Higher Evaporator Temperature Table 3.2 shows the variation of refrigeration capacity, power consumption and specific power consumption for a vapour compression system with variation in evaporator refrigerant gas temperature. It may be observed that higher the evaporator temperature, higher the system capacity, higher the power input and lower the specific power consumption (kW/TR). This clearly indicates that the cooling effect increases in greater proportion than the power consumption, thus, at higher evaporator temperatures, the refrigeration system will cool faster and shut off or unload. The approximate thumb rule is that for every 1°C higher temperature in the ° evaporator, the specific power consumption will decrease by about 2 to 3%. 32
  33. 33. Table 3-2: Effect of Evaporator and Condenser Temperatures on Refrigeration Machine Performance Evaporator Temperature °C +5 0 -5 Condenser Temperatures °C +35 +40 +45 +50 Capacity (TR) Power cons. (kW) Sp. Power (kW/TR) Capacity (TR) Power cons. (kW) Sp. Power (kW/TR) Capacity (TR) Power cons. (kW) Sp. Power (kW/TR) 151 94 0.62 143 102.7 0.72 135 110.6 0.82 127 117.8 0.93 129 90 0.70 118 96.8 0.82 111 103 0.93 104 108.9 1.05 103 84.2 0.82 96 89.6 0.93 90 94.7 1.05 84 99.4 1.19 Increasing the Chilled Water Temperature Set Point The rationale behind temperature settings for all process applications needs to be reviewed, keeping in view the high energy costs. The aim is to avoid unnecessary supercooling, without affecting production, quality and safety. Increasing energy costs have forced many industries to experiment and stabilize process cooling operation at higher temperatures. Improve air Distribution in Cold Storages In cold storage units, single floor mounted large coil and fans may lead to non-uniform temperatures in the cold store, which in turn leads to lower temperature settings. Replacement of single large floor mounted coil-fan-diffuser units (for better air distribution) by smaller wall or ceiling mounted small fan-coil units helps in more uniform distribution of cold air, which, in turn, helps lower temperature settings. resulting large energy savings. This measure has been implemented in some potato cold stores. Improve Air Distribution and Circulation in Air Conditioned Rooms In some air-conditioning systems, lower temperatures are set to over come problems of poor air distribution; making changes in ducting may be a more economical solution than permanently paying higher energy bills. In air-conditioned spaces, use of circulation fans can provide apparent comfort and help raise the room temperature settings to about 26°C or 28°C instead of 24°C. Quiet fans can be concealed behind suspended grids to ensure that the décor is not affected. The reduction in energy consumption in the refrigeration machines will be significantly more than the power consumed by the circulation fans. 3.3 Accurate Measurement and Control of Temperature Most vapour compression machines use superheat sensing expansion valves, which do not give accurate temperature control especially when the compressors are operating at partial loads, resulting in significantly lower temperatures and higher energy consumption. This can be avoided by the use of electronic expansion valves, which are modulating valves that operate based on electronic sensing of the end-use temperature. 33
  34. 34. A Mumbai based company has invented a new temperature controller that senses the temperature of the return air/water/brine and controls the superheat expansion valve by heating or cooling, as necessary, to give very accurate temperature control. This controller can be conveniently retrofitted on the existing superheat sensing system i.e. with out disturbing the existing expansion valve control system. This technology is already commercialized. Some industries and commercial buildings have reported energy savings along with good temperature control between +/-1°C (see case study). 3.4 Reduction in Heat Loads Keep Unnecessary Heat Loads Out Unnecessary heat loads may be kept outside air-conditioned spaces. Often, laboratory ovens are kept in air-conditioned spaces. Such practices may be avoided. Provide dedicated external air supply and exhaust to kitchens, cleaning rooms, combustion equipment etc. to prevent easy mixing of air between warm and cool rooms due to pressure differentials. In cold stores, idle operation of fork lift trucks should be avoided in case of any unforeseen stoppage of material movement. Use False Ceilings Air-conditioning of unnecessary space wastes energy. In rooms with very high ceiling, provision of false ceiling with return air ducts can reduce the air-conditioning load. Relocation of air diffusers to optimum heights in areas with high ceilings is recommended. Use Small Control Panel Coolers CNC machine shops, telecom switching rooms etc. are air-conditioned. As cooling is required only for the panels housing critical circuitry, use of small power panel coolers and hydraulic oil coolers (0.1 to 0.33 TR are available) can make the whole centralised air-conditioning redundant and save energy. Use Pre-Fabricated, Modular Cold Storage Units Cold stores should be designed with collapsible insulated partitions so that the space can be expanded or contracted as per the stored product volumes. The idea is to match product volumes and avoid unnecessary cooling of space and reduce losses. Modular cold store designs are commercially available. Cycle Evaporator Fans in Cold Stores In cold stores that remain shut for long periods, the heat load of the fans can be the major load. After attainment of temperature, refrigerant flow in evaporator fan-coils units and fan operation can be cycled on and off, using a programmable controller. This will reduce the heat load of fans and save energy (see case study). 3.5 Minimising Heat Ingress Cold Stores Many cold stores face serious problems with high energy consumption, ice buildup around doorways, frost and wet floors. They are largely caused by excessive amounts of outside warm air entering the facility at the loading bay. At - 10°C, air can hold only 3 about 2g/m . Table 3.3 shows the comparison of heat ingress through identically sized open doors of air conditioned room and a cold store at -16ºC. Providing an anteroom, providing a high speed door (fig. 3.2) between the cold store and the anteroom and providing a dock leveler (fig. 3.3) to seal the back of the truck to the building are some of the methods to reduce air ingress to cold stores during loading and unloading operations. High speed doors are constructed of light weight, flexible materials for durability. They have minimal insulation properties, but since air exchange is the dominant mode of refrigeration loss, the door's speed becomes more important in controlling refrigeration 34
  35. 35. loss than its insulating properties. A modern high speed door will be open for about 10 seconds per passage. The anteroom in combination with a speed door to the cold store reduces the air infiltration from 2,900 to 700 cubic meters per truck load of cargo moved, a 76 percent reduction. Table 3-3: Heat Ingress into Air-conditioned Space through Open Doors (Door Size: 2m x 1m; Ambient Condition: 30°C & 60% Relative Humidity) Normal Air-conditioned Cold Storage room 24 -16 Room temperature, °C Room relative humidity, % 60 90 Additional heat load, TR 2.5 25 Figure 3-2High Speed Door Figure 3-3: Dock Leveler helps seal back of truck with building Figure 3-4: Example of good thermal insulation in a chilled water system (Observe that chilled water pumps, valves and pipes are al well insulated) 35
  36. 36. Check and Maintain Thermal Insulation Repair damaged insulation after regular checks. Insulate any hot or cold surfaces. Replace wet insulation. Insulate HVAC ducts running outside and through unoccupied spaces. Provide under-deck insulation on the ceiling of the top most floor of airconditioned buildings. Insulate Pipe Fittings Generally, chilled water/brine tanks, pipe lines and end-use equipment in the industry are well insulated. However, valves, flanges etc. are often left uninsulated. With rising energy costs, it pays to insulate pipe flanges, valves, chilled water & brine pumps etc. also (fig. 3.4). Pre-formed insulation or ‘home-made’ box type insulation can be used. For out door piping, provided metal cladding for weather protection. Use Landscaping to the Reduce Solar Heat Load At the time of design of the building, fountains and water flow can be used provide evaporative cooling and act as heat sinks. Trees may be grown around buildings to reduce the heat ingress through windows and also reduce glare. Terrace lawns can help reduce the solar heat gain. Figure 3-5: Typical Modern Building with Glass Façade Reduce Excessive Use of Glass on Buildings Modern commercial buildings (fig. 3.5) use glass facades or large window area (almost 30% of the wall area) resulting in large solar heat gain and heat transmission. Such architecture is suitable for cold countries; in India, it increases the air conditioning load for about eight to ten months in a year. In existing buildings, the possibility of replacing glass panes with laminated insulation boards should be seriously considered. The colour of the laminations can be chosen to suit the internal and external décor. Glass facades, if desired, can be provided in the form of a glass curtain external to a convention wall with necessary window area. Use Glass with Low Solar Heat Gain Coefficient and Thermal Conductivity Table 3.4 shows the solar heat gain coefficient (SHGC), thermal Conductivity and daylight transmittance for different types glass panes. Use of glass with low SHGC and thermal conductivity is recommended. Daylight transmittance is important, if electric lighting (another heat load on air conditioning) has to be minimized. 36
  37. 37. Table 3-4: Properties of Different Types of Window Glass Product Clear Glass Body Tinted Glass Hard Coated Solar Control Glass Soft Coated Solar Control Glass Low Emissivity Glass Solar Control + Low Emissivity Glass Solar Heat Gain Coefficient (SHGC) 0.72 0.45 0.26 Thermal Conductivity 3.16 3.24 3.27 Daylight Transmittance 79 65 24 0.18 3.08 15 0.56 0.23 2.33 1.77 61 41 Use Low Conductivity Window Frames Consider the use of plastic window frames in place of steel and Aluminium frames. This can reduce the heat ingress by conduction. However, security and safety issues related to the use of plastics should also be given due consideration. Provide Insulation on Sun-Facing Roofs and Walls Building insulation has not received much attention in India in spite of the very hot summers. Air-conditioned hotels and corporate office buildings should be constructed with insulated walls (hollow bricks with insulation, double walls with insulation fill etc.) to reduce the heat ingress. Providing roof under-deck insulation is a common practice. Use Doors, Air-Curtains, PVC Strip Curtains for Air Conditioned Spaces Add vestibules or revolving door or self-closing doors to primary exterior doors. Aircurtains and/or PVC strip curtains are recommended for air-conditioned spaces with heavy traffic of people or pallet trucks. Use intermediate doors in stairways and vertical passages to minimise building stack effect. The Biological Sciences Building at Indian Institute of Technology, Kanpur, Roof and Wall Insulation has reduced the cooling load by 23%. The windows to wall ratio is only 7% and double glass insulated glass windows has reduced the cooling load by another 9%. A study of a seven storied modern, air conditioned office building in Mumbai 2 with about 70000 ft has quantified an air conditioning load of 185 TR in summer. Thet window to wall ratio is about 30%. A simulation revealed that blocking 50% of the windows with laminated rigid insulation boards can reduce the air conditioning load by 13%. Providing gypsum board panels along walls with a one inch air gap can reduce the air conditioning load by an additional 4%. The air conditioning system comprising 56 air cooled package air conditioners has an average COP of 2.7. Replacement of air cooled condensers by water cooler condensers can reduce the specific energy consumption by about 40%. 37
  38. 38. 3.6 Reducing Ventilation Heat Load Ventilation is required to for ensuring healthy conditions to the occupants of air conditioned rooms. Most designs provide ventilation of about 15 cfm per person in nonsmoking area. In India, the issue of Indoor Air Quality (IAQ) is usually ignored; ventilation ports are generally kept closed and fresh air is usually available only through door openings. Indoor Air Quality is a serious issue in the developed countries and, in future, buildings in India may also have to adhere to norms. However, with ventilation, the heat load increases as the heat content of fresh air is generally higher in summer. Air to air heat exchangers can help reduce this heat load by pre-cooling the incoming air with out-going exhaust air. Air-to-Air Heat Exchangers for Pre-cooling Ventilation Air Plate Heat Exchangers These heat exchangers use a series of thin Aluminium sheets to transfer heat between two air streams. Sufficient turbulence is created between the plates to improve heat transfer. Warm Air Cold Air Warm Air Cold Air Figure 3-6: Heat Pipes Heat Pipes Heat Pipes (fig. 3.6) usually consist of sealed finned tubes with a wick lining on the inner side. The tube contains a working fluid, which evaporates from the hot end of the tube and condenses at the cold end, thus transferring heat. The working fluid is returned to the hot end by capillary action of the wick. An alternative heat pipe design (without the wick), working on the lines of a re-boiler is also being used. 38
  39. 39. Figure 3-7: Heat Wheel Heat Wheels Heat wheels (fig. 3.7) are rotary heat exchangers packed with Aluminium honey comb fill. One half of the wheel is in contact with the warm air and the other half with the cold air. The sensible heat of the incoming warm air is transferred to one half of the fill; as it rotates slowly and moves into the cold half, the fill transfers the heat to the cold stream. Desiccant coated heat wheels are also available; here, in addition to sensible heat transfer, latent heat transfer also takes place as the desiccant absorbs moisture also. (Also see case study of CII Green Building for an innovative method of pre-cooling ventilation air for an auditorium). Reducing Ventilation Air Requirement by Ozone Dosing The oxygen in the fresh air oxidises the Volatile Organic Compounds (VOC) and odours. The air also dilutes the CO2. The minimum ventilation requirement is 15 cfm per person in a non-smoking room and 30 cfm per person if smoking is permitted. The load on the air conditioning system increases with ventilation. Use of controlled injection of ozone can help reduce the quantity of fresh air. Ozone is a powerful oxidant, which removes odour, VOC and even fungi by oxidation. This reduces the oxygen requirement in the form of ventilation and air is mainly required for diluting CO2. This is a much smaller requirement, thus fresh air can be modulated rationally down to 5 cfm or less per person. However, if residual concentration of ozone exceeds limits, ozone is a toxic gas. The ASHRAE limit is 0.05 ppm. A plate type corona generator in the air duct is recommended along with an auto VOC controller. 3.7 Using Favourable Ambient Conditions Use Cooling Tower Water Directly for Cooling in Winter In locations with dry climate, the winter dry bulb (air) and wet bulb (water) temperatures are very low, especially at nights. During winter, cooling towers may be able to give temperatures of 8°C to 12°C. Plate heat exchangers can be used to transfer the heat load directly to the cooling tower, bypassing the chillers and shutting off the compressors or absorption machines. This system is used in very cold countries to prevent ice buildup in cooling towers. Some industries have successfully implemented this concept 39
  40. 40. during winter, especially during nights when the wet bulb temperature is close to chilled water temperatures. Design New Air-conditioning Systems with Facility for 100% Fresh Air during Winter In air-conditioned systems with centralised AHUs, fresh air and exhaust air ducts can be provided with dampers (and blowers, if necessary) to mix fresh air or use 100% fresh, filtered air, depending on the ambient conditions. These systems should also have the facility to exhaust the stale, warm air. Such air conditioning systems can be fitted with enthalpy sensors and motorised dampers to maximize the use of ambient fresh air during winter and cool summer nights. The normal energy consumption of the air conditioning system may be comparatively less in winter, but even this reduced load can be eliminated if the system design incorporates the facility to take advantage of favourable ambient conditions. Fresh air systems can also be easily retrofitted in most air conditioning systems with centrally located air handling units. Use Ground Source Heat Pumps The near constant temperature in the ground (usually around 26ºC) can be used to cool the air for comfort cooling. Warm air is cooled by drawing it through very long air tunnels created by buring pipes at depths of around 4m. This method is suitable during the dry season. It may not be suitable when the relative humidity is high. This technique has been practically demonstrated at The Energy Research Institute (TERI), Gurgaon. 3.8 Use Evaporators and Condensers with Higher Heat Transfer Efficacy Use Heat Exchangers with Larger Surface Area In the Indian industry, the specific power consumption for chilled water at 6° to 8°C, in reasonably well maintained vapour compression systems, is likely to be around 0.8 kW/TR (only for compressor; pumps & fans are not included). The best systems available in India today can give specific power consumption lower than 0.6 kW/TR (compressor power). In the USA, the specific power consumption figure of chillers is expected to be below 0.56 kW/TR to qualify as an high efficiency chiller. A high efficiency chiller developed by Trane, USA, has a specific power consumption of 0.48 kW/TR. This low specific power consumption has been achieved mainly by use of larger and more effective heat transfer area in the chillers and condensers. Larger area implies more effective heat transfer. This, in turn, implies that the refrigerant temperatures, for the same heat load, will be higher in the evaporator and lower in the condenser. Table 3.2 shows very clearly that higher evaporator temperatures and lower condenser temperatures lead to significant drop in the specific power consumption in the compressor. Hence replacement of chillers/ condensers or increase of heat transfer area by adding additional chillers/condensers in parallel can lead to significant energy savings. 1°C higher temperature in the evaporator or 1°C lower temperature in the ° ° condenser can reduce the specific power consumption by 2 to 3%. Use Plate Heat Exchangers for Process and Refrigeration Machine Condenser Cooling The use of Plate Heat Exchangers for condenser cooling can lead to lower temperature approach, hence reducing the compressor energy consumption. Plate heat exchangers have a temperature approach of 1°C to 5°C instead of around 5°C to 10°C for shell and tube heat exchangers. 40
  41. 41. Avoid the Use of Air Cooled Condensers To take advantage of the wet bulb temperature, use of air-cooled condensers should be avoided for large cooling loads. Air cooled condensers may be permitted only for small cooling loads or in conditions of extreme scarcity of water or lack of space for cooling tower. Condenser water may be provided at the lowest acceptable temperature. Evaporative Pre-coolers for Air-cooled Condensers The performance of air-cooled condensers is limited by the dry bulb temperature. The performance of these condensers can be improved, in dry weather conditions, by providing humidified air near wet bulb temperature. This pre-cooler consists of a cooling pad (with trickling water) through which the air is drawn. Depending on the design, a booster fan may be required to overcome the additional resistance to air flow. The potential for energy saving in dry summer months may be about 30% to 40%. 3.9 Energy Saving Opportunities in Normal Operation Use Building Thermal Inertia in Air Conditioning for Early Switch Off Once the entire building structure is cooled, it takes a few hours to regain normal temperature. This building thermal lag can be used to minimise HVAC equipment operating time by shutting the air-conditioning system half hour or one hour before closing time. Timers or Occupancy Sensors for Window and Split Air Conditioners Window air conditioners and split air conditioners installed for office cabins may operate unnecessarily for long time without any occupancy. The use of timers or infra-red occupancy sensors can help switch of these machines automatically. Interlock Fan Coil Units in Hotels with Door Lock or Master Switch In hotels, unnecessary operation of Fan Coil Units can be prevented by providing an interlock with the door locking system or by switching control at the reception desk. The fan of the fan-coil unit should get switched off or go to low speed mode and the chilled water flow should be cut off by a solenoid valve. This can reduce the air-conditioning load in business hotels, during day time, when rooms are mostly not occupied. Improve Utilisation Of Outside Air. In systems with facility for using fresh air, the use of fresh air should be maximized when ambient conditions are favourable. Maintain Correct Anti-freeze Concentration In systems operating below 5°C, brine or glycol concentration should maintained at the correct levels as this has a significant impact on heat transfer and/or pumping energy. Install Chiller Control System to Co-Ordinate Multiple Chillers. Study part-load characteristics and cycling costs to determine the most efficient mode for operating multiple chillers. Run the chillers with lowest operating costs to serve the base load. Link Chiller control system to the Building Automation System to maximize savings. Permit Lower Condenser Pressures during Favourable Ambient Conditions Favourable ambient conditions reduce cooling air or cooling water temperatures, which will reduce condensing temperatures and pressures, thus reducing the compressor power. The control systems may set to allow the machines to operate at lower condenser pressure. Optimise Water/Brine/Air Flow Rates Optimise condenser water flow rate and chilled water/brine flow rate to maintain the design temperature difference across the chillers and condensers. For normal process 41

×