1.  24 El-Eskandar El-Akbar St., El-Azarita, Alexandria, Egypt.
 Phone (+203) 4858257 - (+203) 4858277 - (+203) 4869407 –
mob. (+2012) 3657186-00971508548073, 00971567850230
 Email.mohsaad7@gmaill.com
 MOHAMED SAAD ABD EL SABOUR AHMED HELALY
 Personal Information
 Nationality: Egyptian
 Religion: Muslim
 Date of birth: 28.7.1980
 Gender: Male
 Marital status: Married
 Military service: Done
 Objective
To obtain a responsible position in a company where my academic background
and personal skills allow me the opportunity of growth.
 Education
Primary school / Saint Kathren

2. Secondary school / Shidwan
[1998-2002] Faculty of Law, Alexandria University. (Grade 63.1)
 Summary of qualifications
Operating systems
Windows Me, XP & windows &
Microsoft Office (MS Word, MS Excel, MS PowerPoint)
Internet applications
 Professional Experience
End Client Name: Exxon Mobil (from 23/02//2015 till30/04/2015)
 Client Name Marine Harkand & TILONE subsea
 Continued Project Title 2014 USAN Subsea Baseline Inspections
 Vessel Name Bourban Evolution 802
 Company – Blisston Nigeria limited
 As a 3.4u inspection engineer and data recorder
 Scope of Work:
The subsea surveys shall consist of visual inspections (VI) and cathodic protection (CP)
system survey (anode condition survey and CP potential measurement). The inspection
and survey work shall be conducted using a work class ROV. However, a diver
inspection may be considered for survey of the CP system on areas difficult to access by

3. ROV such as the FPSO hull underside. Where a diver is used, the Contractor shall adhere
strictly to the specification of ExxonMobil’s Diving requirements.
The subsea inspection shall involve the use of ROV to inspect all subsea equipment (In-
line tee; Flow line end terminals; Christmas Trees; Jumpers), risers, flow lines
(including flex joints), umbilical, underwater part of the FPSO Hull, offloading lines
(including flex joints), and the submerged part of the calm buoy. The subsea inspection
shall cover but not limited to the following:
• General condition of the equipment
 • Detection of leaks
 Condition of features such as crossings, mechanical anchors, saddle blocks,
junctions, sub-sea valves assemblies, spool pieces, flanged joints, mechanical
connectors, or hyperbaric weld
 • Condition of the insulation
 • Condition of the anticorrosion coating
 • Condition of the field joints wrapping
 • Detection of bare metal areas
 • Cathodic protection potential measurement/anodes activity and depletion
 • Presence of debris in contact/close proximity to any equipment
 • Verification and measurement of free spans
 • Detection of scouring of subsea equipment support
 • Any other anomaly that may compromise the integrity of the subsea
equipment.
 The general field layout of USAN field inspection zone is as shown in Figure 2.
Eleven main areas have been detailed and sketched up graphically, however for
the current scope shall cover only ten areas as outlined below:
 1. South Production Loop
 2. South Water Injection Line
 3. South Production Umbilical distribution
 4. North Production Loop
 5. North Water Injection Line
 6. North Production Umbilical distribution
 7. South Gas Injection Line
 8. Gas Injection Umbilical distribution
 9. Risers & Umbilical arches
 10. OLT System
End Client Name: Exxon Mobil (from 23/09//2014 till10/11/2014)
 Client Name Marine HALLIN & TILONE subsea
 Project Title 2014 USAN Subsea Baseline Inspections

4.  Vessel Name Bourban Evolution 802
 Company – Blisston Nigeria limited
 As a 3.4u inspection engineer and data recorder
 Scope of Work:
The subsea surveys shall consist of visual inspections (VI) and cathodic protection (CP)
system survey (anode condition survey and CP potential measurement). The inspection
and survey work shall be conducted using a work class ROV. However, a diver
inspection may be considered for survey of the CP system on areas difficult to access by
ROV such as the FPSO hull underside. Where a diver is used, the Contractor shall adhere
strictly to the specification of ExxonMobil’s Diving requirements.
The subsea inspection shall involve the use of ROV to inspect all subsea equipment (In-
line tee; Flow line end terminals; Christmas Trees; Jumpers), risers, flow lines
(including flex joints), umbilical, underwater part of the FPSO Hull, offloading lines
(including flex joints), and the submerged part of the calm buoy. The subsea inspection
shall cover but not limited to the following:
• General condition of the equipment
 • Detection of leaks
 Condition of features such as crossings, mechanical anchors, saddle blocks,
junctions, sub-sea valves assemblies, spool pieces, flanged joints, mechanical
connectors, or hyperbaric weld
 • Condition of the insulation
 • Condition of the anticorrosion coating
 • Condition of the field joints wrapping
 • Detection of bare metal areas
 • Cathodic protection potential measurement/anodes activity and depletion
 • Presence of debris in contact/close proximity to any equipment
 • Verification and measurement of free spans
 • Detection of scouring of subsea equipment support
 • Any other anomaly that may compromise the integrity of the subsea
equipment.
 The general field layout of USAN field inspection zone is as shown in Figure 2.
Eleven main areas have been detailed and sketched up graphically, however for
the current scope shall cover only ten areas as outlined below:
 1. South Production Loop
 2. South Water Injection Line
 3. South Production Umbilical distribution
 4. North Production Loop
 5. North Water Injection Line

5.  6. North Production Umbilical distribution
 7. South Gas Injection Line
 8. Gas Injection Umbilical distribution
 9. Risers & Umbilical arches
 10. OLT System
 End Client Name: ZADCO
 Client Name: ZADCO from (27-04-2014 till 29-06-2014)
 Location: UPPER ZAKUM field ABU DHABI
 Vessel name: M/V ZAKHER ADMIRAL
 As a 3.4u inspection engineer and data recorder
 Scope of Work:
End Client Name: ZADCO :
3.4 subsea controller( coordinator) / Data recorder.
(Creation a final reports for Clint review and approval)
On board M/V ZAKHER ADMIRAL in the subsea inspection offshore structures
and flow line contract with zadco at zakum field .
-Structure inspection.
- Risers inspection
- Anode survey
- Conductors ‘survey
- Water jet cleaning for clamps.
- Still photos for selected anodes and risers tube turn
- Pipe line survey
- Riser video Survey.
 Client Name: E- MARINE from (06-02-2014 till 01-04-2014)
 Location: UMM AL DALAKH field ABU DHABI

6.  Vessel name: M/V Stanford Hunter
 As a 3.4u inspection engineer and data recorder
Scope of Work
Following instruction from ZADCO,E-MARINE, MUTAWA MARINE divers
onboard M/V Stanford Hunter conducted the 2014 underwater installation of
electrical submersible pump at UMM Al Dalakh field (CPP, LQP, WHP01, WHP02,
WHP07 and WHP11)Platforms.
The inspection program encompassed underwater specific legs of the
structures.
Legs NO: B1, D1, and D2 at CPP. /Leg NO: M1 at LQP. /Leg NO: A1 at WHP01.
Leg NO: A2 at WHP02. / Leg NO: A1 at WHP07. /Leg NO: A1 at WHP11.
There were installed clamps on the specific legs platforms.
There were revealed cables on the specific legs platforms.
 End Client Name: British Petroleum (BP)
 Client Name: Dalgidj underwater-technical,ROV & Diving operations
from (11/2013 till 01/2014 )
 Location: CASPIAN SEA (AZRI. Field).
 Vessel/Rig Name: M/V CITADEL.
 As a 3.4u inspection engineer and data recorder
Scope of Work
The Scope of Work for the 2013 EA (PDQ) Platform ROV structural
inspection programmed comprises of the following activities:
- Structure GVI

7. - FMD Survey
- GVI of Gas/Oil Risers, Water Injection Risers, Spool Pieces and
Guides
- GVI of Caissons and Supports
- GVI of J Tubes and Support Clamps
- GVI of Conductors and Conductor Guides
- CPMs of Jacket
- CPMs of Risers, Spool Pieces and Guides
- CPMs of Caissons and Supports
- CPMs of J Tubes and Supports
- CPMs of Conductors, Guides and Template
- Seabed Survey
Summary of Inspection Work scope
Inspection Category Extent of Inspection Survey
GVI – Swim round Jacket members, piles and pile clusters, and legs
at all levels from seabed up to LAT. This survey
also includes the drilling template, boat landing
and the conductor protection nets. At least one
side of every component is to be inspected with
all round inspection where damage is suspected.Flooded Member
Detection Survey
Survey of all subsea members of Jacket
(excluding the legs which are flooded), support
stubs to guides and clamps for risers, caissons
and J-tubes.GVI - Risers,
Spool pieces and
Guides
Risers, spool pieces and riser bolted clamp
attachments to jacket. Free spans in spool
pieces should be reported as anomalies
(anomaly code SU).
GVI - Caissons
and Supports
All caissons, caisson supports to jacket and in
particular at the intakes as well as around the
level of the pumps (where present).
Note: If possible the Cutting Caisson (C5)
should be assessed during drilling in
progress in order to check cutting flow at EL -
14m and end of the caisson

8. GVI - J-Tubes and
Support Clamps
All J-Tubes and bolted clamp attachments to
jacket.
GVI – Conductors
and Conductor
Guides
All conductors and conductor guides.
Note: Special attention needs to be given to
conductor No. 42 at EL -39m in order to check
discharge which was identified based on 2010
ROV inspection video records
Cathodic Potential
Measurements –
Jacket
Legs, selected jacket members, template, piles
and pile guides at selected locations shown in
sketches and listed in datasheets.
Cathodic Potential
Measurements -
Risers,
Spoolpieces and
Guides
Risers and guides at each guide elevation and
midway between guides. Spool pieces at 5m
intervals from riser base flange to burial point or
to 25m out from the base of the jacket.
Cathodic Potential
Measurements -
Caissons and
Supports
Caissons and supports at each support
elevation, caissons midway between supports
and at bottom.
Cathodic Potential
Measurements - J-
Tubes and
Support Clamps
J-Tube and support clamps at each clamp
elevation and mid-way between clamps.
Cathodic Potential
Measurements -
Conductors,
Guides and
Template
Conductors and guides at elevations shown in
the datasheet.
Anode Survey Not planned for year 2013
Seabed Survey Conductors, piles and legs at the mud line. Level
of the scour / deposition is to be estimated to +/-
150mm relative to centre of -146.1m bracing at
legs and conductors. Clear debris from jacket
and template to 5m from jacket; spool pieces to
burial point or for 25m from riser base flange.

9. Wall Thickness
Measurement
Not planned for 2013 survey
-
End Client Name: Exxon Mobil (from 09/2013 till 11/2013)
 Client Name Marine Platforms
 Project Title ERHA FPSO the Hull External under water
 Vessel Name SIEM MARLIN
 Field ERHA FPSO Hull External under water Inspection
 Company – Blisston Nigeria limited
 As a 3.4u inspection engineer and data recorder
 Carry out CVI, GVI, FMD, CP and Valve survey for the subsea
asset integrity Manifolds, Riser towers, flexible risers and X
Trees
 MPL was asked to perform an inspection on the Calm Buoy
mooring lines in the ERHA field. This inspection was done on
behalf of the client, Exxon Mobil. The inspection was performed
by ROV on board the vessel, the Siem Marlin. The inspection
started on the 17th of October 2013. Below is a list of the
inspections performed and completed.
 ERHA Calm Buoy Mooring Lines
 100% overall general visual inspection of all 8 mooring lines.
 General visual inspections on the suction pile anchors.
 Close visual inspection of the spelter sockets.
 CP readings on the suction pile and mooring lines.
 Inspections of anodes protection where fitted.

10. MPL was asked to perform a UWILD inspection on the ERHA
FPSO. This inspection was done on behalf of the client, Exxon
Mobil. The inspection was carried out by ROV on board the
vessel, the Siem Marlin. The inspection started on the 19th
of
October 2013. Below is a list of the inspections performed.
FPSO UWILD INSPECTION
 General visual inspections of the port side shell sections.
 General visual inspections of the starboard side shell sections.
 General visual inspections of the bow and stern side shell sections.
 CP readings on the bottom shell (12 locations)
 General visual inspection of the anodes.
 Close visual inspection of the bottom shell sections
o Client ADMA – OPCO, (from 09/2012 till 08/2013)
Inspection diver.
Onboard DSV Faisal-1 in the Subsea inspection of
Offshore Structures and flow line contract with
ADMA-OPCO at Umm Shaif, Zakum Field and
Das lsland.
On board MA/ Mutawa 11 in the Provision of sub
sea inspection services (Additional Diving Support
vessel & other resources) for ADMA-OPCO
contract.
Scope of work included:-
- Pipe line inspection
- Riser inspection
- inspection offshore structures.
- maintenance work like install boat landing ,anodes ,clamps ,fenders .
o Client Zadco
Inspection diver .
On board dsv mutawa 9 in the subsea inspection offshore structures and flow
line contract with zadco at zakum field and um al dalakh Scope of work included .

11. On board dsv zakher admiral in the subsea inspection offshore structures and
flow line contract with zadco at zakum field and um al dalakh Scope of work
included:-
- Conductor removal, using hydraulic drilling machine to drill a hall and install a
pin in side
-use hydraulic saw ( guilloten) to cut the conductor.
- Riser inspection
- Anode survey
- Grit Blast to selected node for MPl.
- MPI survey (Magnetic Particle inspection)
- Conductors ‘survey
- Water jet cleaning for conductors clamps.
- Still photos for selected anodes and risers tube turn
- Pipe line survey
- Riser video Survey.
o Client: ADOC
Inspection Diver
On board MA/ Mutawa 11 in the Provision of sub
sea inspection services (Additional Diving Support
Vessel & other resources) for ADMA-OPCO
Contract.
Scope of work included:-
- Riser inspection
- Anode survey
- Grit Blast to selected node for MPl.
- MPI survey (Magnetic Particle inspection)
- Conductors ‘survey
- Water jet cleaning for risers clamps
- Water jet cleaning for conductors clamps.
- Still photos for selected anodes and risers tube turn
- Pipe line survey
- Riser video Survey.
o Client: ADMA/NPGC project No.8053
Inspection Diver
On board SEP 250 for diving services for Flare and
J5 jackets installation
o Client: Hyundai
Inspection Diver
Third party diving inspection works at Das island
Inspection Diver
Onboard DSV Faisal-1 in the Subsea inspection of
Offshore Structures and flow line contract with
ADMA-OPCO at Umm Shaif, Zakum Field and
Das island including the following:-

12. - General visual inspection
- C.P. Survey
- U.T. Survey
- Video & Photography
- Air Lifting, Grit Blasting
- Water Jetting
- Assist in ACFM Survey
- Assist in Sonoma tic Survey
Sep 2008 – present
 Mutawa Marine Works LLC.
Air Diver
o Client: CORODEX, Dubai
Palm island Development Project
Air Diver
Scope of Work:
10"-16" Pipeline Trenching and installation Works
Offshore
o Client: TOTAL ABK
Inspection Diver
Onboard DSV ZAKHER PRIDE, in the Subsea
Inspection and Maintenance of Offshore
Structures and Flow lines. Duties covering all
Requirements for client on inspection contract i.e.
Structure, flow line inspections, Survey, Still
Photography, video inspection, CP, UT reading,
Water jetting, etc..
Client ADMA-OPCO
On board DSVs NMS 401 & NMS 402 for ADMAOPCO.
Duties include the following:-
- Bottom Survey for Offshore Structures prior to Rig moves;
- Diving Services during Rig moves
- Leg Penetration check for Rigs - Anchor Handling Operations
- Photography
- Video inspections
- General Maintenance for Offshore Structures
Jan 2008 -Aug 2008
AL-YOUSUF Maritime Services
Air Diver
Scope of work included: - Remove and put frames under water - Put cement and
concrete using pump - Put concrete blocks under water using crane - Under
water survey.

13. Training professional diving centre
 Certificate
1- Class 4 , 3 , 2 air diving (commercial diving 50 m ) , first aid certificate
2- Underwater inspector grade 3.1u in accordance with the cswip
requirements published in document cswip – div-7-95-part 1,3rd edition
June 2009 Date of issue 23/7/2009Date of expiry 12/6/2014
3-Cswip 3.4u – underwater inspection controller
Date issue 28/8/2012
Date of expiry 28/8/2017
4-Trainee Offshore Air Diving Supervisor
5- COABIS subsea inspector course held at AKER SOLUTIONS, ABERDEEN
on 10/04/2014.
 HSE courses.
1-Tropical basic offshore safety induction emergency training (OPITO approved
course code – 5501) certificate number: 005855012607125577.
2-B.A & H2S

14. 2-Basic H2S training (OPITO approved course code –9014)
 Skills
Ability to work under stress.
Adapting myself with any new tool and new environment.
Working alone or as a member of teamwork.
Good handling problems.
Good communicating and presentation skills.
Computer skills.
 Language
Arabic (Mother tongue)
English (Very good)