This document presents information on optical detectors. It begins with an overview of optical communication systems and fiber optic architecture. It then discusses the key components of optical receivers including light sources, detectors, and fiber-optic cables. Common types of optical detectors are photo diodes (PIN and APD). PIN diodes have good linearity and speed but lower sensitivity, while APDs provide internal gain but more noise. Characteristics like responsivity, bandwidth, capacitance, and noise are examined. Factors influencing detector performance and tradeoffs between bandwidth and efficiency are also summarized.
Optical detectors details and technologies with formulas
1. NAME :
SYED KAMRAN HAIDER
PRESENTATION:
OPTICAL DETECTORS
FOUNDATION UNIVERSITY RAWALPINDI CAMPUS
2. OPTICAL COMMUNICATION SYSTEMS
Communication systems with light as the carrier and optical
fiber as communication medium
Optical fiber is used to contain and guide light waves
Typically made of glass or plastic
Propagation of light in atmosphere is impractical
This is similar to cable guiding electromagnetic waves
Capacity comparison
Microwave at 10 GHz
Light at 100 Tera Hz (1014 )
2
3. HISTORY
1880 Alexander G. Bell
Photo phone, transmit sound waves over beam of light
1930: TV image through uncoated fiber cables
Few years later image through a single glass fiber
1951: Flexible fiberscope: Medical applications
1956: The term “fiber optics” used for the first time
1958: Paper on Laser & Maser
3
4. HISTORY CONT’D
1960: Laser invented
1967: New Communications medium: cladded fiber
1960s: Extremely lossy fiber:
More than 1000 dB /km
1970: Corning Glass Work NY, Fiber with loss of less than
2 dB/km
70s & 80s : High quality sources and detectors
Late 80s : Loss as low as 0.16 dB/km
1990: Deployment of SONET systems
4
5. OPTICAL FIBER ARCHITECTURE
Transmitter
Input
Signal
Coder or
Converter
Light
Source
Source-to-Fiber
Interface
Fiber-to-light
Interface
Light
Detector
Amplifier/Shaper
Decoder
Output
Fiber-optic Cable
Receiver
TX, RX, and Fiber Link
5
6. OPTICAL FIBER ARCHITECTURE –
COMPONENTS
Light source:
Amount of light emitted is
proportional to the drive
current
Two common types:
LED (Light Emitting
Diode)
ILD (Injection Laser
Diode)
Source–to-fiber-coupler
(similar to a lens):
A mechanical interface to
couple the light emitted by
the source into the optical
fiber
Input
Signal
Coder or
Converter
Light
Source
Source-to-Fiber
Interface
Fiber-to-light
Interface
Light
Detector
Amplifier/Shaper
Decoder
Output
Fiber-optic Cable
Receiver
Light detector:
PIN (p-type-intrinsic-n-type)
APD (avalanche photo diode)
Both convert light energy into
current
6
7. LIGHT DETECTORS
PIN Diodes
photons are absorbed in the intrinsic layer
sufficient energy is added to generate carriers in the
depletion layer for current to flow through the device
Avalanche Photodiodes (APD)
photogenerated electrons are accelerated by
relatively large reverse voltage and collide with other
atoms to produce more free electrons
avalanche multiplication effect makes APD more
sensitive but also more noisy than PIN diodes
7
9. OPTICAL DETECTORS.
These are transducers that convert optical
signals into electrical signals.
Transducers are devices that convert input
energy of one form into output energy of
another.
An optical detector does so by generating
an electrical current proportional to the
intensity of the incident optical light.
9
10. OPTICAL DETECTOR REQUIREMENTS.
Compatible in size to low-pass optical fibers
for efficient coupling and packaging.
High sensitivity at the operating wavelength
of the source.
Low noise contribution.
Maintain stable operation in changing
environmental conditions.
10
12. PHOTO DETECTION PRINCIPLES
(Hitachi Opto Data Book)
Device Layer Structure
Band Diagram
showing carrier
movement in E-field
Light intensity as a
function of distance below
the surface
Carriers absorbed here must
diffuse to the intrinsic layer
before they recombine if they are
to contribute to the photocurrent.
Slow diffusion can lead to slow
“tails” in the temporal response.
Bias voltage usually needed
to fully deplete the intrinsic “I”
region for high speed
operation
12
14. CHARACTERISTICS OF PHOTODETECTORS
Number of Collected electrons
1
Number of Photons *Entering* detector
/Number of Collected electrons
1 1
Number of Photons *Incident* on detector /
Photo Current (Amps)
W
i
ph W
e p
o
e
i q
R e
P h
R
1 1
Incident Optical Power (Watts)
1 1ph o
ph W
p
o
W
p
oi RP
i q
R e
P h
R e
P
q
h
• Internal
Quantum Efficiency
•External
Quantum efficiency
• Responsivity
•Photocurrent
Incident Photon Flux
(#/sec)
Fraction Transmitted
into Detector
Fraction absorbed in
detection region
14
16. OPTICAL DETECTOR MATERIALS.
Si,GaAs, GaAlAs – 850nm
Ge, InP, InGaAs -1300nm and 1550nm.
Materials determine the responsivity of the
detector which is the ratio of the output
photocurrent to the incident optical power.
It’s a function of the wavelength and
efficiency of the device.
16
17. PIN PHOTODIODE.
Semiconductor positive-negative structure
with an intrinsic region sandwiched between
the other two regions.
Normally operated by applying a reverse-
bias voltage.
Dark current can also be produced which is
a leakage current that flows when a reverse
bias is applied without incident light.
17
20. PIN DIODE STRUCTURES
Diffused Type
(Makiuchi et al. 1990)
Etched Mesa Structure
(Wey et al. 1991)
Diffused Type
(Dupis et al 1986)
Diffused structures tend to have lower dark current than mesa etched
structures although they are
more difficult to integrate with electronic devices because an additional high
temperature processing step is required.
20
21. RESPONSE TIME FACTORS.
Thickness of the active area.
-Related to the amount of time required for
the electrons generated to flow out of the
detector active area.
Detector RC time constant.
-Depends on the capacitance of the
photodiode and the resistance of the load.
21
22. ADVANTAGE OF PIN PHOTODIODES.
The output electrical current is linearly proportional
to the input optical power making it a highly linear
device.
Low bias voltage(<4v).
Low noise
Low dark current
High-speed response
22
23. AVALANCHE PHOTODIODE.
•High resistivity p-doped
layer increases electric
field across absorbing
region
•High-energy electron-hole
pairs ionize other sites to
multiply the current
•Leads to greater
sensitivity
23
24. AVALANCHE PHOTODIODES.
An APD internally amplifies the photocurrent by an
avalanche process when a large reverse-bias voltage is
applied across the active region.
The gain of the APD can be changed by changing the
reverse-bias voltage.
24
27. DETECTOR EQUIVALENT CIRCUITS
Iph
Rd
Id Cd
PIN
Iph
Rd
Id Cd
APD
In
Iph=Photocurrent generated by detector
Cd=Detector Capacitance
Id=Dark Current
In=Multiplied noise current in APD
Rd=Bulk and contact resistance
27
28. MSM DETECTORS
Semi insulating Ga
•Simple to fabricate
•Quantum efficiency: Medium
Problem: Shadowing of absorption
region by contacts
•Capacitance: Low
•Bandwidth: High
Can be increased by thinning absorption layer and
backing with a non absorbing material. Electrodes
must be moved closer to reduce transit time.
•Compatible with standard electronic processes
GaAs FETS and HEMTs
InGaAs/InAlAs/InP HEMTs
To increase speed
decrease electrode spacing
and absorption depth
Absorption
layer
Non absorbing substrate
E Field
penetrates for
~ electrode spacing
into material
Simplest Version
Schottky barrier
gate metal
Light
28
29. WAVEGUIDE PHOTODETECTORS
(Bowers IEEE 1987)
•Waveguide detectors are suited for very high bandwidth applications
•Overcomes low absorption limitations
•Eliminates carrier generation in field free regions
•Decouples transit time from quantum efficiency
•Low capacitance
•More difficult optical coupling 29
31. DETECTOR CAPACITANCE
p-n junction
xp xn
For a uniformly doped junction
Where: =permitivity q=electron charge
Nd=Active dopant density
Vo=Applied voltage V bi=Built in potential
A=Junction area
C
A
W
w xp xn
C
A
2
2q
Vo Vbi
Nd
1/ 2
W
2(Vo Vbi)
qNd
1/2
P N
Capacitance must be minimized for high
sensitivity (low noise) and for high speed
operation
Minimize by using the smallest light collecting
area consistent with efficient collection of the
incident light
Minimize by putting low doped “I” region
between the P and N doped regions to
increase W, the depletion width
W can be increased until field required to fully
deplete causes excessive dark current, or
carrier transit time begins to limit speed.
31
32. BANDWIDTH LIMIT
C=0K A/w
where K is dielectric constant, A is area, w is
depletion width, and 0 is the permittivity of free
space (8.85 pF/m)
B = 1/2RC
32
33. PIN BANDWIDTH AND EFFICIENCY TRADEOFF
Transit time
=W/vsat
vsat=saturation velocity=2x107 cm/s
R-C Limitation
Responsivity
Diffusion
=4 ns/µm (slow)
RC in
A
R
W
1 1 W
pR
q
R e
h
33
34. DARK CURRENT
Surface Leakage
Bulk Leakage
Surface Leakage
Ohmic Conduction
Generation-recombination
via surface states
Bulk Leakage
Diffusion
Generation-Recombination
Tunneling
Usually not a significant noise source at high bandwidths for PIN Structures
High dark current can indicate poor potential reliability
In APDs its multiplication can be significant
34
35. SIGNAL TO NOISE RATIO
ip= average signal photocurrent level
based on modulation index m where
2
22
2 p
p
Im
i
LBLDp
p
RTBkBqIBMFMIIq
Mi
N
S
/422 2
22
35
36. OPTIMUM VALUE OF M
where F(M) = Mx and m=1
Dp
LBLx
opt
IIxq
RTkqI
M
/422
36
37. NOISE EQUIVALENT POWER (NEP)
Signal power where S/N=1
Units are W/Hz1/2
L
x
D
RM
kT
MeI
e
h
NEP 2
4
2
37
39. COMPARISONS
PIN gives higher bandwidth and bit rate
APD gives higher sensitivity
Si works only up to 1100 nm; InGaAs up to 1700,
Ge up to 1800
InGaAs has higher for PIN, but Ge has higher M
for APD
InGaAs has lower dark current
39